The microstructure, mechanical and friction properties of protective diamond like carbon films on magnesium alloy

Protective hard coatings deposited on magnesium alloys are believed to be effective for overcoming their poor wear properties. In this work, diamond-like carbon (DLC) films as hard protective films were deposited on AZ91 magnesium alloy by arc ion plating under negative pulse bias voltages ranging from 0 to −200 V. The microstructure, composition and mechanical properties of the DLC films were analyzed by scanning electron microscopy, Raman spectroscopy, X-ray photoelectron spectroscopy and nanoindentation. The tribological behavior of uncoated and coated AZ91 magnesium alloy was investigated using a ball-on-disk tribotester. The results show that the negative pulse bias voltage used for film deposition has a significant effect on the sp³ carbon content and mechanical properties of the deposited DLC films. A maximum sp³ content of 33.3% was obtained at −100 V, resulting in a high hardness of 28.6 GPa and elastic modulus of 300.0 GPa. The DLC films showed very good adhesion to the AZ91 magnesium alloy with no observable cracks and delamination even during friction testing. Compared with the uncoated AZ91 magnesium alloy, the magnesium alloy coated with DLC films exhibits a low friction coefficient and a narrow, shallow wear track. The wear resistance and surface hardness of AZ91 magnesium alloy can be significantly improved by coating a layer of DLC protective film due to its high hardness and low friction coefficient.     

Effect of pulse electrodeposition parameters on the properties of Ni/nano-SiC composites

Pure nickel and nickel matrix composite deposits containing nano-SiC particles were produced under both direct and pulse current conditions from an additive-free nickel Watts’ type bath. It has been proved that composite electrodeposits prepared under pulse plating conditions exhibited higher incorporation percentages than those obtained under direct plating conditions, especially at low duty cycles. The study of the textural perfection of the deposits revealed that the presence of nano-particles led to the worsening of the quality of the observed [1 0 0] preferred orientation. Composites with high concentration of embedded particles exhibited a mixed crystal orientation through [1 0 0] and [2 1 1] axes. The embedding SiC nano-particles in the metallic matrix by an intra-crystalline mechanism resulted in the production of composite deposits with smaller crystallite sizes and more structural defects than those of pure Ni deposits. A dispersion-hardening effect was revealed for composite coatings independently from applied current conditions. Pulse electrodeposition significantly improved the hardness of the Ni/SiC composite deposits, mainly at low duty cycle and frequency of imposed current pulses.     

Electroless preparation and characterization of magnetic Ni-P plating on polyurethane foam

Magnetic Ni-P plating was coated on surface of polyurethane (PU) foam by electroless plating technique. Morphology, composition, structure, thermal decomposing behavior and magnetic property of PU foam before and after plating were characterized by scanning electron microscopy (SEM), energy diffraction spectrum (EDS), X-ray photoelectron spectroscopy (XPS), infrared spectrometer (IR), X-ray diffraction (XRD), thermogrametric analysis (TG) and vibrating sample magnetometer (VSM), respectively. The results showed that the Ni-P plating was composed by particles whose diameters were in the range of 1-2 μm. Because of the Ni-P plating coated on surface of PU foam, peak intensity of the plated PU foam in IR and XRD were lower than those before plating. TG curves of PU foam before and after plating were composed of two decomposing stages. Because part of Ni in Ni-P plating was oxidized, TG curve of the plated PU foam was uptilt during 650-1000 °C. The plated PU foams are magnetic and can be used in some special application.     

Study of deposition patterns of plating layers in SiC/Cu composites by electro-brush plating

SiC reinforced copper composite coatings were prepared by electro-brush plating with micron-size silicon carbide (SiC) ranging from 1 to 5 μm on pure copper sheet in this paper. The micro-structural characterizations of SiC/Cu composite coatings were performed by optical microscope and Scanning Electron Microscope (SEM) coupled with spectrometer, to study co-deposition mechanism of SiC/Cu. It was found that there were three different patterns of SiC deposition in plating layers during electro-brush plating process, i.e. the particles could deposit inside copper grains, in grain boundaries, or in holes of the surface. To investigate deposition mechanism of each pattern, size of SiC and copper grains was compared. By comparison of size of copper grains and hard particles, SiC were either wrapped in copper grains or deposited in grain boundaries. Moreover, electro-brush plating layers at different brush velocities and current densities were obtained respectively, to analyze the microstructure evolution of the composite coatings. The hardness of plating layers was measured. The results indicated at the current density of 3 A/dm², the SiC/Cu coating was compact with SiC content at a high level and the hardness reached a maximum.     

Electrochemical studies of zinc-nickel codeposition in sulphate bath

The electrodeposition of Zn-Ni alloys from a sulphate bath was studied under different conditions. The bath had the composition 0.40 M sodium sulphate, 0.01 M sulphuric acid, 0.16 M boric acid, 0.20 M zinc sulphate and 0.20 M nickel sulphate. It is found that the plating bath temperature has a great effect on the cyclic voltammograms, galvanostatic measurements during electrodeposition, and consequently linear polarization resistance for corrosion study and the alloy composition. Under the examined conditions, the electrodeposition of the alloys was of anomalous type. X-ray diffraction measurements revealed that the alloys consisted of the δ-phase (Ni₃Zn₂₂) or a mixture of the two phases δ and γ (Ni₅Zn₂₁). The comparison between Ni deposition and Zn-Ni codeposition revealed that the remarkable inhibition of Ni deposition takes place due to the presence of Zn²⁺ in the plating bath. The Ni deposition starts at −0.85 V in the bath of Ni deposition only, but the deposition starts at more negative potentials in the codeposition bath although the concentration of Ni²⁺ is the same in the both baths.     

Electrochemical behavior of cobalt from 1-butyl-3-methylimidazolium tetrafluoroborate ionic liquid

The electrodeposition of metallic cobalt from a 1-butyl-3-methylimidazolium tetrafluoroborate ionic liquid was investigated. The electrochemical behavior of Co(II) in the ionic liquid on a platinum working electrode at 60 °C was studied by cyclic voltammetry and chronoamperometry. The results from the cyclic voltammetry showed that the electrodeposition of metallic Co in the ionic liquid was an irreversible process and controlled by the diffusion of Co(II) on a platinum working electrode. The average value of αn_α was calculated to be 0.35 and the diffusion coefficient (D₀) of Co(II) was calculated to be 1.76 × 10⁻⁸ cm²/s at 60 °C. Chronoamperometric results indicated that the electrodeposition of Co on a platinum working electrode followed the mechanism of instantaneous nucleation and three-dimensional growth with diffusion-controlled. The cobalt plating was uniform, dense, shining in appearance with good adhesion to the platinum substrate at 60 °C. The scanning electron microscope (SEM) micrographs were used to confirm that the cobalt plating was denser and finer at 60 °C. Energy dispersive X-ray analysis (EDAX) profile showed that the obtained plating was pure cobalt. X-ray diffraction (XRD) pattern indicated that there was a preferred orientation direction and the average size of cobalt grains was 40 nm.     

The effect of surface nanocrystallization on plasma nitriding behaviour of AISI 4140 steel

A plastic deformation surface layer with nanocrystalline grains was produced on AISI 4140 steel by means of surface mechanical attrition treatment (SMAT). Plasma nitriding of SMAT and un-SMAT AISI 4140 steel was carried out by a low-frequency pulse excited plasma unit. A series of nitriding experiments has been conducted at temperatures ranging from 380 to 500 °C for 8 h in an NH₃ gas. The samples were characterized using X-ray diffraction, scanning electron microscopy, optical microscopy and Vickers microhardness tester. The results showed that a much thicker compound layer with higher hardness was obtained for the SMAT samples when compared with un-SMAT samples after nitriding at the low temperature. In particular, plasma nitriding SMAT AISI 4140 steel at 380 °C for 8 h can produced a compound layer of 2.5 μm thickness with very high hardness on the surface, which is similar to un-SMAT samples were plasma nitrided at approximately 430 °C within the same time.     

Effect of nickel on the initial growth behavior of electroless Ni-Co-P alloy on silicon substrate

In this work the small amounts of NiSO₄ was added to a basic electroless plating bath of CoSO₄ with Na₂H₂PO₂ as reducing agent for the deposition of Co-Ni-P film on a silicon substrate. The initial growth behavior, containing plating rate, chemical composition, crystal structure, surface morphology and micro-structure, of the electroless plating film was characterized by scanning electron microscope (SEM) and transmission electron microscope (TEM). The results showed that the growth morphology variation of the Co-Ni-P films deposited in the basic CoSO₄ + small amounts of NiSO₄ bath is the same as that of Co-P film deposited in the basic CoSO₄ bath, the plating rate of the Co-Ni-P film is much more rapid than that of the Co-P film, the Ni/Co wt.% in the Co-Ni-P film is greatly larger than that in the plating bath, and the structure of as-deposited film is crystalline at first stage and later stage.     

Microstructure and properties of Ni-Co/nano-Al2O3 composite coatings by pulse reversal current electrodeposition

Ni-Co/nano-Al₂O₃ (Ni-Co/Al₂O₃) composite coatings were prepared under pulse reversal current (PRC) and direct current (dc) methods respectively. The microstructure of coatings was characterized by means of XRD, SEM and TEM. Both the Ni-Co alloy and composite coatings exhibit single phase of Ni matrix with face-centered cubic (fcc) crystal structure, and the crystal orientation of the Ni-Co/Al₂O₃ composite coating was transformed from crystal face (2 0 0) to (1 1 1) compared with alloy coatings. The hardness, anti-wear property and macro-residual stress were also investigated. The results showed that the microstructure and performance of the coatings were greatly affected by Al₂O₃ content and the electrodeposition methods. With the increasing of Al₂O₃ content, the hardness and wear resistance of the composite coatings enhanced. The PRC composite coatings exhibited compact surface, high hardness, better wear resistance and lower macro-residual stress compared with that of the dc composite coatings.     

Friction and wear properties of the co-deposited Ni-SiC nanocomposite coating

Ni-SiC nanocomposite coatings were produced by electrodeposition from a nickel sulfate bath containing SiC nanoparticles with an average particle size of 30 nm. The characteristics of the coatings were assessed by scanning electron microscopy and microhardness test. The friction and wear performance of Ni-SiC nanocomposite coatings and Ni film were comparatively investigated sliding against Si₃N₄ ceramic balls under non-lubricated conditions. The results indicated that compared to Ni film, Ni-SiC nanocomposite coating exhibited enhanced microhardness and wear resistance. The effect of SiC nanoparticles on the friction and wear resistance is discussed in detail.     

Effect of deposition and annealing temperature on mechanical properties of TaN film

Tantalum nitride films (TaN) were synthesized by microwave ECR-DC sputtering. The effects of deposition and annealing temperature on mechanical properties of TaN films were investigated. Cross-section pattern, microstructure and binding energy of the films were investigated by scanning electron microscope (SEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), respectively. Mechanical properties were evaluated using nano-indentation and scratch tester. The results showed that the maximal hardness value of approximately 40 GPa was deposited in the TaN sample at 573 K. While the preparation temperature decreased, the hardness, modulus and adhesion of TaN film also decreased. Hardness and modulus also decreased with the increase in annealing temperature. Meanwhile the adhesion strength was also sensitive to the annealing temperature, with a maximum adhesion strength of 40 N measured in the TaN film annealed at 448 K. The results demonstrated that a desirable mechanical property of TaN films deposited by DC reactive magnetron sputtering can be obtained by controlling the deposition and annealing temperature.     

Self-lubricative coating grown by micro-plasma oxidation on aluminum alloys in the solution of aluminate-graphite

Aluminum trioxide ceramic coatings with high hardness were grown on surfaces of 2024 Aluminum alloys by micro-plasma oxidation in an aluminate electrolytic solution, which highly improve wear-resisting properties of 2024 Aluminum alloys. However, ceramic coating surfaces are porous and very coarse, which is disadvantageous to practical applications. In this paper, in order to increase the density of the pores and decrease the friction coefficient of the ceramic coatings, different concentrations (2-8 g/l) of graphite were added into the aluminate electrolytic solution. The thickness and hardness of the produced ceramic coatings were measured by HVS-100 micro-hardness tester and thickness tester. The friction coefficient of the coatings was studied by a frictionometer. The phase composition and surface morphology of the MPO films were evaluated through X-ray diffraction (XRD) and scanning electron microscope (SEM). The results show that the thickness of the ceramic coating is about 22 ± 1 μm, surfaces of the ceramic coatings are very uniform and that the coatings consist of mainly aluminum trioxides and a certain amount of graphite, which indicates graphite have entered the ceramic films during the micro-plasma oxidation process. Wear properties results show that the friction coefficient of the ceramic coatings decreased when graphite entered the ceramic films. When the concentration of graphite is 4 g/l, the wear properties of the coatings is the most excellent and the friction coefficient decreases to the lowest, that is 0.09.     

Mechanical properties and wear and corrosion resistance of electrodeposited Ni-Co/SiC nanocomposite coating

Ni-Co/SiC nanocomposite coatings with various contents of SiC nano-particulates were prepared by electrodeposition in a Ni-Co plating bath containing SiC nano-particulates to be co-deposited. The influences of the nanoparticulates concentration, current density, stirring rate and temperature of the plating bath on the composition of the coatings were investigated. The shape and size of the SiC nano-particulates were observed and determined using a transmission electron microscope. The polarization behavior of the composite plating bath was examined on a PAR-273A potentiostat/galvanostat device. The wear behavior of the Ni-Co/SiC nanocomposite coatings was evaluated on a ball-on-disk UMT-2MT test rig. The worn surface morphologies of the Ni-Co/SiC nanocomposite coatings were observed using a scanning electron microscope. The corrosion behavior of the nanocomposite coatings was evaluated by charting the Tafel curves of the solution of 0.5 mol L⁻¹ NaCl at room temperature. It was found that the cathodic polarization potential of the composite electrolyte increased with increasing SiC concentration in the plating bath. The microhardness and wear and corrosion resistance of the nanocomposite coatings also increased with increasing content of the nano-SiC in the plating bath, and the morphologies of the nanocomposite coatings varied with varying SiC concentration in the plating bath as well. Moreover, the co-deposited SiC nano-particulates were uniformly distributed in the Ni-Co matrix and contributed to greatly increase the microhardness and wear resistance of the Ni-Co alloy coating.     

Preparation and Characterization of Nanostructured Ni-TiN Composite Films

在悬浮有TiN纳米颗粒的镍镀液中,采用直流电镀方法制备了Ni-TiN纳米复合镀层. 采用原子力显微镜、X射线衍射仪和透射电镜等手段对镀层结构、表面形貌、耐蚀性能、硬度和热稳定性等进行了研究,并且与传统镍镀层的相应性能进行了比较. 结果表明,复合镀层在耐腐蚀性、硬度和热稳定性等方面都比传统镍镀层有了显著提高;由于电流密度对阴极析氢和镍晶粒的成核/生长速率的影响,Ni-TiN纳米复合镀层的硬度随着电镀电流密度的增加而轻微减小.     

Nanocrystalline nickel films with lotus leaf texture for superhydrophobic and low friction surfaces

Nanostructured Ni films with high hardness, high hydrophobicity and low coefficient of friction (COF) were fabricated. The surface texture of lotus leaf was replicated using a cellulose acetate film, on which a nanocrystalline (NC) Ni coating with a grain size of 30 ± 4 nm was electrodeposited to obtain a self-sustaining film with a hardness of 4.42 GPa. The surface texture of the NC Ni obtained in this way featured a high density (4 × 10³ mm⁻²) of conical protuberances with an average height of 10.0 ± 2.0 μm and a tip radius of 2.5 ± 0.5 μm. This structure increased the water repellency and reduced the COF, compared to smooth NC Ni surfaces. The application of a short-duration (120 s) electrodeposition process that deposited “Ni crowns” with a larger radius of 6.0 ± 0.5 μm on the protuberances, followed by a perfluoropolyether (PFPE) solution treatment succeeded in producing a surface texture consisting of nanotextured protuberances that resulted in a very high water contact angle of 156°, comparable to that of the superhydrophobic lotus leaf. Additionally, the microscale protuberances eliminated the initial high COF peaks observed when smooth NC Ni films were tested, and the PFPE treatment resulted in a 60% reduction in the steady-state COFs.     

Characterization and corrosion behavior of hydroxyapatite/zirconia composite coating on NiTi fabricated by electrochemical deposition

NiTi alloy is used as biomaterial due to its unique properties, but the high content of Ni (about 50 at.%) in biomedical NiTi is concerned. Hydroxyapatite and hydroxyapatite/zirconia composite coatings were directly electrodeposited on NiTi alloy surface. The coated samples were characterized using X-ray diffraction, scanning electron microscopy, infrared spectroscopy, bonding strength test, polarization and EIS. Results showed that when ZrO₂ was added into the electrolyte, morphology of HAP was changed from thin flake-flower-like crystals to needle-flower-like crystals, and coating was denser. Besides, HAP crystal grains in the coating were preferentially arranged in the [0 0 1] direction. Addition of ZrO₂ could improve the bonding strength between the coating and the substrate. Corrosion resistance of NiTi in the simulated body fluid at 37 °C was significantly improved by almost 60 times by electrodeposition of the hydroxyapatite/zirconia composite coating.     

Development of electroless Ni-Zn-P/nano-TiO2 composite coatings and their properties

Ni-Zn-P-TiO₂ composite coatings were successfully obtained on low carbon steel by electroless plating technique. Deposits were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive analysis (EDS) studies. The hardness and microstructure of as plated and heat treated Ni-Zn-P and Ni-Zn-P-TiO₂ composite coatings were analyzed. The change in microstructure and higher hardness was noticed for heat treated composite. The corrosion resistance behavior of as plated and heat treated Ni-Zn-P and Ni-Zn-P-TiO₂ coatings was investigated by anodic polarization, Tafel plots and electrochemical impedance spectroscopic (EIS) studies in 3.5 wt% NaCl solution. The composite coating exhibited enhanced corrosion resistance property over Ni-Zn-P coating.     

制备铋靶的脉冲电镀工艺

 采用脉冲电镀工艺,以直径为1 mm的铜丝为芯轴,在无氰镀液体系中,制备出惯性约束聚变实验用铋靶所需的金属铋镀层。通过正交试验得到的最佳脉冲工艺条件为：电流密度5 A/cm²,频率600 Hz,占空比1∶6,温度20 ℃。利用扫描探针显微镜和扫描电子显微镜分别对铋镀层表面形貌进行分析,同时利用X射线衍射对铋镀层物相成分进行分析。表征结果表明：所得铋镀层表面细致均匀,孔隙率低,平整性好,无裂纹。     

Preparation and properties of electroless Ni-P-SiO2 composite coatings

Dispersible SiO₂ nanoparticles were co-deposited with electroless Ni-P coating onto AISI-1045 steel substrates in the absence of any surfactants in plating bath. The resulting Ni-P/nano-SiO₂ composite coatings were heat-treated for 1 h at 200 °C, 400 °C, and 600 °C, respectively. The hardness and wear resistance of the heat-treated composite coatings were measured. Moreover, the structural changes of the composite coatings before and after heat treatment were investigated by means of X-ray diffraction (XRD), while their elemental composition and morphology were analyzed using an energy dispersive spectrometer (EDS) and a scanning electron microscope (SEM). Results show that co-deposited SiO₂ particles contributed to increase the hardness and wear resistance of electroless Ni-P coating, and the composite coating heat-treated at about 400 °C had the maximum hardness and wear resistance.     

Effect of deposition voltage on the field emission properties of electrodeposited diamond-like carbon films

Diamond-like carbon (DLC) films were deposited on Al substrates by electrodeposition technique under various voltages. The surface morphology and compositions of synthesized films were characterized by scanning electron microscopy and Raman spectroscopy. With the increase of deposition voltage, the sp² phase concentration decreased and the surface morphology changed dramatically. The influence of deposition voltage on the field electron emission (FEE) properties of DLC films was not monotonic due to two adverse effects of deposition voltage on the surface morphology and compositions. The DLC film deposited under 1200 V exhibited optimum FEE property, including a lowest threshold field of 13 V/μm and a largest emission current density of 904.8 μA/cm² at 23.5 V/μm.