Correlation between Al2O3 particles and interface of Al-Al2O3 coatings by cold spray

Al-Al₂O₃ composite coatings with different Al₂O₃ particle shapes were prepared on Si and Al substrate by cold spray. The powder compositions of metal (Al) and ceramic (Al₂O₃) having different sizes and agglomerations were varied into ratios of 10:1 wt% and 1:1 wt%. Al₂O₃ particles were successfully incorporated into the soft metal matrix of Al. It was found that crater formation between the coatings and substrate, which is typical characteristic signature of cold spray could be affected by initial starting Al₂O₃ particles. In addition, when the large hard particles of fused Al₂O₃ were employed, the deep and big craters were generated at the interface between coatings and hard substrates. In the case of pure soft metal coating such as Al on hard substrate, it is very hard to get proper adhesion due to lack of crater formation. Therefore, the composite coating would have certain advantages.     

Microstructure and properties of Ni-Co/nano-Al2O3 composite coatings by pulse reversal current electrodeposition

Ni-Co/nano-Al₂O₃ (Ni-Co/Al₂O₃) composite coatings were prepared under pulse reversal current (PRC) and direct current (dc) methods respectively. The microstructure of coatings was characterized by means of XRD, SEM and TEM. Both the Ni-Co alloy and composite coatings exhibit single phase of Ni matrix with face-centered cubic (fcc) crystal structure, and the crystal orientation of the Ni-Co/Al₂O₃ composite coating was transformed from crystal face (2 0 0) to (1 1 1) compared with alloy coatings. The hardness, anti-wear property and macro-residual stress were also investigated. The results showed that the microstructure and performance of the coatings were greatly affected by Al₂O₃ content and the electrodeposition methods. With the increasing of Al₂O₃ content, the hardness and wear resistance of the composite coatings enhanced. The PRC composite coatings exhibited compact surface, high hardness, better wear resistance and lower macro-residual stress compared with that of the dc composite coatings.     

Effect of NaAlO2 concentrations on microstructure and corrosion resistance of Al2O3/ZrO2 coatings formed on zirconium by micro-arc oxidation

In this study, Al₂O₃/ZrO₂ composite coatings were prepared on Zr substrates by micro-arc oxidation (MAO) in the NaAlO₂-containing electrolytes, and the effect of NaAlO₂ concentration on the microstructure, bond strength, microhardness and corrosion resistance of coatings was systematically investigated. The study reveals that the adequate NaAlO₂ in the electrolyte (>0.2 M) is essential to the formation of needle-like α-Al₂O₃ in the coatings, and the amount of α-Al₂O₃ rises with the increase of the NaAlO₂ concentration. m-ZrO₂ and t-ZrO₂ are present in all of the coatings, but their relative amount largely depends on the amount of Al₂O₃. It is also found that as the NaAlO₂ concentration increases from 0.2 to 0.3 M, the coating becomes denser and thicker, and its bond strength, maximum microhardness and corrosion resistance increases as well. The coating formed at 0.3 M NaAlO₂ demonstrates the highest bond strength of 52 MPa, the maximum microhardness of 1600 Hv_0.2N and the superior corrosion resistance. However, the overhigh concentration of NaAlO₂ (0.35 M) is found harmful to the coating's microstructure and properties.     

Preparation and characterization of nickel nano-Al2O3 composite coatings by sediment co-deposition

Ni-Al₂O₃ composite coatings were prepared by using sediment co-deposition (SCD) technique and conventional electroplating (CEP) technique from Watt's type electrolyte without any additives. The microstructure, hardness, and wear resistance of resulting composites were investigated. The results show that the incorporation of nano-Al₂O₃ particles changes the surface morphology of nickel matrix. The preferential orientation is modified from (2 0 0) plane to (1 1 1) plane. The microhardness of Ni-Al₂O₃ composite coatings in the SCD technique are higher than that of the CEP technique and pure Ni coating and increase with the increasing of the nano-Al₂O₃ particles concentration in plating solution. The wear rate of the Ni-Al₂O₃ composite coating fabricated via SCD technique with 10 g/l nano-Al₂O₃ particles in plating bath is approximately one order of magnitude lower than that of pure Ni coating. Wear resistance for SCD obtained composite coatings is superior to that obtained by the CEP technique. The wear mechanism of pure Ni and nickel nano-Al₂O₃ composite coatings are adhesive wear and abrasive wear, respectively.     

Preparation and wear resistance of pulse electrodeposited Ni-W/Al2O3 composite coatings

The aim of this work is to obtain the electroplating parameters for preparation of Ni-W/Al₂O₃ composite coating with high tungsten content, high micro-hardness and excellent wear resistance by pulse plating procedure. Our results showed that the duty cycle is a dominant parameter for the tungsten content in the coating and the tungsten content increases significantly with increasing duty cycle. The further analysis showed the great influence of tungsten content on micro-hardness of the coating. A maximum micro-hardness of about 859 Hv was obtained in pulse electrodeposited Ni-W/Al₂O₃ composite with tungsten content of 40 wt.% at a peak current density of 20 A/dm², a duty cycle of 80%, a pulse frequency of 1000 Hz and a particle loading of 10 g/L alumina in the plating bath. Although the hardness of Ni-W/Al₂O₃ composite coating was only slightly affected by the alumina content of the deposits prepared in present investigation, the alumina content effect on the tribological characteristic of Ni-W/Al₂O₃ composite coatings is significant. The friction coefficient was lowered to 0.25 and the wear loss was reduced to 1.05 mg by setting the control factors according to the values mentioned above for obtaining the coating with the highest micro-hardness.     

Plasma sprayed Al2O3/FeCrAl composite coatings for electromagnetic wave absorption application

Al₂O₃/FeCrAl composite coatings were fabricated by atmosphere plasma spraying technique. Microstructure and dielectric properties in the frequency range from 8.2 to 12.4 GHz were investigated. The microstructure of composite coatings shows a uniform dispersion of metal particles with litter pores and microcracks in the composite coatings. The relaxation polarization and interfacial polarization in the coatings would contribute to enhance ?′ with rising FeCrAl content, and the associated loss could be considered as a dominating factor enhancing ?″. By calculating the microwave-absorption as a single-layer absorber, for the composite coatings with 41 wt.% FeCrAl content, the reflection loss values exceeding −10 dB are achieved in the frequency range of 9.1-10.6 GHz when the coating thickness is 1.3 mm.     

Influence of treating frequency on microstructure and properties of Al2O3 coating on 304 stainless steel by cathodic plasma electrolytic deposition

Alumina ceramic coatings were fabricated on 304 stainless steel by cathodic plasma electrolytic deposition (CPED). Influence of treating frequency of the power supply on the microstructure and properties of the coatings were studied. The results indicated that coatings obtained at various frequencies on 304 stainless steels were all composed of α-Al₂O₃ and γ-Al₂O₃, and α-Al₂O₃ was the dominant phase. The contents of α-Al₂O₃ decreased gradually in a very small rate with increasing the frequency and γ-Al₂O₃ gradually increased. The surface of alumina ceramic coating was porous. With increasing the frequency, the coating surface gradually became less rough and more compact, resulting in low surface roughness. The bonding strength of Al₂O₃ coating was higher than 22 MPa and was not strongly affected by treating frequency. With increasing the frequency, the alumina coated steels showed better and gradually increasing corrosion resistance than the uncoated one in 3.5% NaCl solution. The coating steel with desirable corrosion resistance was obtained at 800 Hz whose corrosion current potential and corrosion density were −0.237 V and 7.367 × 10⁻⁸ A/cm², respectively.     

Coating formation by plasma electrolytic oxidation on ZC71/SiC/12p-T6 magnesium metal matrix composite

Plasma electrolytic oxidation (PEO) of a ZC71/SiC/12p-T6 magnesium metal matrix composite (MMC) is investigated in relation to coating growth and corrosion behaviour. PEO treatment was undertaken at 350 mA cm⁻² (rms) and 50 Hz with a square waveform in stirred 0.05 M Na₂SiO₃.5H₂O/0.1 M KOH electrolyte. The findings revealed thick, dense oxide coatings, with an average hardness of 3.4 GPa, formed at an average rate of ∼1 μm min⁻¹ for treatment times up to 100 min and ∼0.2 μm min⁻¹ for later times. The coatings are composed mainly of MgO and Mg₂SiO₄, with an increased silicon content in the outer regions, constituting <10% of the coating thickness. SiC particles are incorporated into the coating, with formation of a silicon-rich layer at the particle/coating interface due to exposure to high temperatures during coating formation. The distribution of the particles in the coating indicated growth of new oxide at the metal/coating interface. The corrosion rate of the MMC in 3.5% NaCl is reduced by approximately two orders of magnitude by the PEO treatment.     

Microstructure and mechanical properties of Al2O3-Al composite coatings deposited by plasma spraying

Al₂O₃ and Al₂O₃-Al composite coatings were prepared by plasma spraying. Phase composition of powders and as-sprayed coatings was determined by X-ray diffraction (XRD), while optical microscopy (OM) and scanning electron microscopy (SEM) were employed to investigate the morphology of impacted droplets, polished and fractured surface, and the element distribution in terms of wavelength-dispersive spectrometer (WDS). Mechanical properties including microhardness, adhesion and bending strength, fracture toughness and sliding wear rate were evaluated. The results indicated that the addition of Al into Al₂O₃ was beneficial to decrease the splashing of impinging droplets and to increase the deposition efficiency. The Al₂O₃-Al composite coating exhibited homogeneously dispersed pores and the co-sprayed Al particles were considered to be distributed in the splat boundary. Compared with Al₂O₃ coating, the composite coating showed slightly lower hardness, whereas the coexistence of metal Al phase and Al₂O₃ ceramic phase effectively improved the toughness, strength and wear resistance of coatings.     

Atmospheric reactive plasma sprayed Fe-Al2O3-FeAl2O4 composite coating and its property evaluation

In the present study, Fe-Al₂O₃-FeAl₂O₄ composite coatings were successfully deposited by reactive plasma sprayed Al/Fe₂O₃ agglomerated powder. Phase composition and microstructure of the coatings were determined by XRD and SEM. The results indicated that the composite coatings were principally composed of three different phases, i.e. FeAl₂O₄ phase as main framework, dispersed ball-like Fe-rich phase, and small splats of Al₂O₃ phase, and it was thought that the in situ synthesized metal phase was helpful to toughen the coating matrix. According to the results of the indentation and frictional wear tests, the composite coating exhibited excellent toughness and anti-friction properties in comparison with conventional Al₂O₃ monophase coating, though its microhardness value was a little lower than that of Al₂O₃ coating. The formation mechanism and the toughening mechanism of the composite coating were clarified in detail.     

Investigation of the characteristics and corrosion resistance of Al2O3/TiN coatings

Al₂O₃ /TiN double and Al₂O₃/Cr/TiN triple coatings were produced on stainless steel substrates using plasma-detonation techniques. Investigation of the microstructure and characteristics of the coatings after the preparation was performed by X-ray diffraction (XRD), transmission electron microscopy (TEM) and Auger electron spectroscopy (AES). The corrosion resistance of the coatings was studied in several electrolytic solutions (0.5 M H₂SO₄, 1 M HCl, 0.75 M NaCl) using electrochemical techniques (open circuit potential, cyclovoltammetry and potentiodynamic polarization). The obtained results showed, in most of the cases, an improvement of the corrosion resistance, except in NaCl solutions. The effect of the controlled thickness of TiN and Cr layers as well as the additional treatment with a high-current electron beam was also investigated. Nuclear reaction analysis (NRA), Rutherford backscattering spectroscopy (RBS) and scanning electron microscopy (SEM) were applied for the characterization of the samples before and after the corrosion experiments.     

Ni-Co-TiO2 nanocomposite coating prepared by pulse and pulse reversal methods using acetate bath

Ni-Co/nano TiO₂ (Ni-Co-TiO₂) composite coatings were prepared under pulse current and pulse reverse current methods using acetate bath. The microstructure and corrosion resistance of the coatings were characterized by means of XRD, SEM and EIS. Both the Ni-Co alloy and composite coatings exhibited single phase of Ni matrix with face centered cubic (fcc) crystal structure. The crystal orientation of the Ni-Co-TiO₂ composite coating was transformed from crystal face (2 0 0) to (1 1 1) compared with Ni-Co alloy coatings. The results showed that the microstructure and performances of the coatings were greatly affected by TiO₂ content on the deposits prepared by PC and PRC methods. The microhardness and corrosion resistance were enhanced in the optimum percentage of TiO₂ composite coatings. The PRC composite coatings were exhibited from compact surface, higher microhardness and good corrosion resistance compared with that of the PC composite coating.     

Effects of duty ratio at low frequency on growth mechanism of micro-plasma oxidation ceramic coatings on Ti alloy

The aim of this work is to study the effects of duty ratio on the growth mechanism of the ceramic coatings on Ti-6Al-4V alloy prepared by pulsed single-polar MPO at 50 Hz in NaAlO₂ solution. The phase composition of the coatings was studied by X-ray diffraction, and the morphology and the element distribution in the coating were examined through scanning electron microscopy and energy dispersive spectroscopy. The thickness of the coatings was measured by eddy current coating thickness gauge. The corrosion resistance of the coated samples was examined by linear sweep voltammetry technique in 3.5% NaCl solution. The changes of the duty ratio (D) of the anode process led to the changes of the mode of the spark discharge during the pulsed single-polar MPO process, which further influenced the structure and the morphology of the ceramic coatings. The coatings prepared at D = 10% were composed of a large amount of Al₂TiO₅ and a little γ-Al₂O₃ while the coatings prepared at D = 45% were mainly composed of α-Al₂O₃ and γ-Al₂O₃. The coating thickness and the roughness were both increased with the increasing D due to the formation of Al₂O₃. The formation of Al₂TiO₅ resulted from the spark discharge due to the breakdown of the oxide film, while the formation of Al₂O₃ resulted from the spark discharge due to the breakdown of the vapor envelope. The ceramic coatings improved the corrosion resistance of Ti-6Al-4V alloy. And the surface morphology and the coating thickness determined the corrosion resistance of the coated samples prepared at D = 45% was better than that of the coated samples prepared at D = 10%.     

Microstructure and properties of TiB2-containing coatings prepared by arc spraying

Low cost arc spraying and cored wires were used to deposit composite coatings consisting of TiB₂ and TiB₂/Al₂O₃ hard particles in a Ni(Cr) and stainless steel 304L matrix. Four coatings were prepared namely Ni(Cr)-TiB₂, Ni(Cr)-TiB₂/Al₂O₃, 304L-TiB₂ and 304L-TiB₂/Al₂O₃. The microstructural characteristics of powders and coatings were observed by scanning electron microscopy (SEM). Phase compositions of powders were analyzed by X-ray diffraction (XRD). Although all the analyzed coatings exhibited similar lamella structure, remarkable differences not only in the morphology of hard phase and matrix but also in the size and distribution of hard phases were observed from one coating to another. Tribological behavior of the coatings was analyzed in room temperature dry sliding wear tests (block-on-ring configuration), under 75 N at low velocity (0.5 m/s). The coatings showed far high wear resistance than low carbon steel substrate under same conditions examined. Wear loss of 304L-TiB₂ and Ni(Cr)-TiB₂ coatings were lower nearly 15 times than that of steel substrate. TiB₂ hard phases in coatings bonded well with metal matrix contributed to high wear resistance.     

Corrosion resistance of cerium-based conversion coatings on alumina borate whisker reinforced AA6061 composite

Cerium-based conversion coatings on Al₁₈B₄O₃₃w/6061Al composite surface were obtained by immersing the composite into a solution containing various concentrations of CeCl₃. Results indicate that the susceptibility to pitting for the conversion-coated composites was much lower than that of the untreated composite, and the corrosion resistance of the coated composites was improved markedly; moreover, the concentration of CeCl₃ in the cerium solution affects significantly the corrosion behaviors of the coated composites. The coating obtained from a solution containing 7.5 g CeCl₃ into 1000 ml produced better corrosion resistance on the composite due to the surface being almost covered by conversion coating. EDX and XPS experimental results indicated that the coatings were made up of oxygen, cerium, and aluminum.     

Electrodeposition and characterization of Ni-Y2O3 composite

Nano-sized Y₂O₃ particles were codeposited with nickel by electrolytic plating from a nickel sulfate bath. The effects of the incorporated Y₂O₃ on the structure, morphology and mechanical properties (including microhardness, friction coefficient and wear resistant) of Ni-Y₂O₃ composite coatings were studied. It is observed that the addition of nano-sized Y₂O₃ particles shows apparent influence on the reduction potential and pH of the electrolyte. The incorporated Y₂O₃ increases from 1.56 wt.% to 4.4 wt.% by increasing the Y₂O₃ concentration in the plating bath from 20 to 80 g/l. XRD results reveal that the incorporated Y₂O₃ particles favour the crystal faces (2 0 0) and (2 2 0). SEM and AFM images demonstrate that the addition of Y₂O₃ particles causes a smooth and compact surface. The present study also shows that the codeposited Y₂O₃ particles in deposits decrease the friction coefficient and simultaneously reduce the wear weight loss. Ni-Y₂O₃ composite coatings reach their best microhardness and tribological properties at Y₂O₃ content 4.4 wt.% under the experiment conditions.     

Suspension plasma sprayed composite coating using amorphous powder feedstock

Al₂O₃-ZrO₂ composite coatings were deposited by the suspension plasma spray process using molecularly mixed amorphous powders. X-ray diffraction (XRD) analysis shows that the as-sprayed coating is composed of α-Al₂O₃ and tetragonal ZrO₂ phases with grain sizes of 26 nm and 18 nm, respectively. The as-sprayed coating has 93% density with a hardness of 9.9 GPa. Heat treatment of the as-sprayed coating reveals that the Al₂O₃ and ZrO₂ phases are homogeneously distributed in the composite coating.     

Interfacial reactions and oxidation behavior of Al2O3 and Al2O3/Al coatings on an orthorhombic Ti2AlNb alloy

The uniform and dense Al₂O₃ and Al₂O₃/Al coatings were deposited on an orthorhombic Ti₂AlNb alloy by filtered arc ion plating. The interfacial reactions of the Al₂O₃/Ti₂AlNb and Al₂O₃/Al/Ti₂AlNb specimens after vacuum annealing at 750 °C were studied. In the Al₂O₃/Ti₂AlNb specimens, the Al₂O₃ coating decomposed significantly due to reaction between the Al₂O₃ coating and the O-Ti₂AlNb substrate. In the Al₂O₃/Al/Ti₂AlNb specimens, a γ-TiAl layer and an Nb-rich zone came into being by interdiffusion between the Al layer and the O-Ti₂AlNb substrate. The γ-TiAl layer is chemically compatible with Al₂O₃, with no decomposition of Al₂O₃ being detected. No internal oxidation or oxygen and nitrogen dissolution zone was observed in the O-Ti₂AlNb alloy. The Al₂O₃/Al/Ti₂AlNb specimens exhibited excellent oxidation resistance at 750 °C.     

Preparation and properties of composite ceramic coating containing Al2O3–ZrO2–Y2O3 on AZ91D magnesium alloy by plasma electrolytic oxidation

A composite ceramic coating containing Al₂O₃–ZrO₂–Y₂O₃ was successfully prepared on AZ91D magnesium alloy by plasma electrolytic oxidation (PEO) technique in an alkaline aluminate electrolyte. The morphology, elemental and phase composition, corrosion behavior and thermal stability of the uncoated and coated samples were studied by environmental scanning electron microscopy (ESEM), energy dispersive X-ray spectrometer (EDS), X-ray diffractometer (XRD), electrochemical corrosion test, high temperature oxidation test and thermal shock test. The results showed that the composite ceramic coating was composed of Al₂O₃, c-ZrO₂, t-ZrO₂, Y₂O₃ and some magnesium compounds, such as MgO, MgF₂ and MgAl₂O₄. After PEO treatment, the corrosion potential of AZ91D alloy was increased and the corrosion current density was significantly reduced. Besides, the coated magnesium alloys also showed excellent high temperature oxidation resistance and thermal shock resistance at 500 °C environment.     

Improving Fe3Al alloy resistance against high temperature oxidation by pack cementation process

The paper presents the results of oxidation tests of Fe₃Al-based alloys containing additions of Cr, Zr, B, and C, with and without an aluminide coating. The coating was formed by a pack cementation process in which the surface of material got enriched in aluminum. The Al-rich layer was intended to enhance the tendency of Al₂O₃ formation. The slow-growing Al₂O₃ scale provides the best corrosion protection for structural materials at high temperatures. The cyclic oxidation tests were performed in laboratory air at 1373 K. The structure and composition of oxide scales as well as their adherence were evaluated and compared for the materials with and without aluminide coatings. Surface enrichment in aluminum and effect minor addition of Zr on oxidation behavior was discussed.