Thermal stability of Ag films in air prepared by thermal evaporation

The thermal stability of silver films in air has been studied. Pure Ag films, 250 nm in thickness, were prepared on glass substrates by thermal evaporation process, and subsequently annealed in air for 1 h at temperatures between 200 and 400 °C. The structure and morphology of the samples were investigated by X-ray diffraction, Raman spectra and atomic force microscopy. It is found that the crystallization enhances for the annealed films, and film surface becomes oxidized when annealing temperature is higher than 350 °C. The electrical and optical properties of the films were studied by van der Pauw method and spectrophotometer, respectively. Reflectance drops sharply as Ag films are annealed at temperatures above 250 °C. Film annealed at 250 °C has the maximum surface roughness and the minimum reflectance at 600 nm optical wavelength. Film annealed at 200 °C has the minimum resistivity, and resistivity increases with the increasing of the annealing temperature when temperature is above 200 °C. The results show that both oxidization on film surface and agglomeration of silver film result in infinite of electrical resistivity as the annealing temperature is above 350 °C.     

Influence of annealing temperature on structural and optical properties of ZnO: In thin films prepared by ultrasonic spray technique

Transparent conducting indium doped zinc oxide was deposited on glass substrate by ultrasonic spray method. The In doped ZnO samples with indium concentration of 3 wt.% were deposited at 300, 350 and 400 °C with 2 min of deposition time. The effects of substrate temperature and annealing temperature on the structural, electrical and optical properties were examined. The DRX analyses indicated that In doped ZnO films have polycrystalline nature and hexagonal wurtzite structure with (0 0 2) preferential orientation and the maximum average crystallite size of ZnO: In before and annealed at 500 °C were 45.78 and 55.47 nm at a substrate temperature of 350 °C. The crystallinity of the thin films increased by increasing the substrate temperature up 350 °C, the crystallinity improved after annealing temperature at 500 °C. The film annealed at 500 °C and deposited at 350 °C show lower absorption within the visible wavelength region. The band gap energy increased from E_g = 3.25 to 3.36 eV for without annealing and annealed films at 500 °C, respectively, indicating that the increase in the transition tail width. This is due to the increase in the electrical conductivity of the films after annealing temperature.     

Optical constants and thermocoloration of pulsed laser deposited molybdenum oxide thin films

Molybdenum oxide thin films were prepared by pulsed laser deposition. The as-deposited films were dark. Annealing the films in air at 400 °C resulted in transparent films. These films were further annealed in vacuum at 300 and 400 °C to investigate thermocoloration. The structural, chemical, and optical properties of the films were determined. All films were predominantly amorphous. The air-annealed films were nearly stoichiometric. However, after annealing in vacuum at 400 °C, the films became oxygen-deficient. The transmittance of the films progressively decreased as the vacuum-annealing temperature increased, indicating stronger coloration of the films. The optical constants were determined from the transmittance measurements. Both the refractive index and extinction coefficient increased upon vacuum annealing. However, the band gap slightly decreased after vacuum annealing.     

Effect of post-annealing on the properties of copper oxide thin films obtained from the oxidation of evaporated metallic copper

Thin films of copper oxide were obtained through thermal oxidation (100-450 °C) of evaporated metallic copper (Cu) films on glass substrates. The X-ray diffraction (XRD) studies confirmed the cubic Cu phase of the as-deposited films. The films annealed at 100 °C showed mixed Cu-Cu₂O phase, whereas those annealed between 200 and 300 °C showed a single cubic Cu₂O phase. A single monoclinic CuO phase was obtained from the films annealed between 350 and 450 °C. The positive sign of the Hall coefficient confirmed the p-type conductivity in the films with Cu₂O phase. However, a relatively poor crystallinity of these films limited the p-type characteristics. The films with Cu and CuO phases show n-type conductivity. The surface of the as-deposited is smooth (RMS roughness of 1.47 nm) and comprised of uniformly distributed grains (AFM and SEM analysis). The post-annealing is found to be effective on the distribution of grains and their sizes. The poor transmittance of the as-deposited films (<1%) is increased to a maximum of ∼80% (800 nm) on annealing at 200 °C. The direct allowed band gap is varied between 2.03 and 3.02 eV.     

Influence of temperature annealing on optical properties of SrTiO3/BaTiO3 multilayered films on indium tin oxide

We have prepared SrTiO₃/BaTiO₃ thin films with multilayered structures deposited on indium tin oxide (ITO) coated glass by a sol-gel deposition and heating at 300-650 °C. The optical properties were obtained by UV-vis spectroscopy. The films show a high transmittance (approximately 85%) in the visible region. The optical band gap of the films is tunable in the 3.64-4.19 eV range by varying the annealing temperature. An abrupt decrease towards the bulk band gap value is observed at annealing temperatures above 600 °C. The multilayered film annealed at 650 ° C exhibited the maximum refractive index of 2.09-1.91 in the 450-750 nm wavelength range. The XRD and AFM results indicate that the films annealed above 600 ° C are substantially more crystalline than the films prepared at lower temperatures which were used to change their optical band gap and complex refractive index to an extent that depended on the annealing temperature.     

The effect of heat treatment on the physical properties of sol-gel derived ZnO thin films

Zinc oxide (ZnO) thin films were deposited on microscope glass substrates by sol-gel spin coating method. Zinc acetate (ZnAc) dehydrate was used as the starting salt material source. A homogeneous and stable solution was prepared by dissolving ZnAc in the solution of monoethanolamine (MEA). ZnO thin films were obtained after preheating the spin coated thin films at 250 °C for 5 min after each coating. The films, after the deposition of the eighth layer, were annealed in air at temperatures of 300 °C, 400 °C and 500 °C for 1 h. The effect of thermal annealing in air on the physical properties of the sol-gel derived ZnO thin films are studied. The powder and its thin film were characterized by X-ray diffractometer (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure (JCPDS 36-1451) and show the c-axis grain orientation. Increasing annealing temperature increased the c-axis orientation and the crystallite size of the film. The annealed films are highly transparent with average transmission exceeding 80% in the visible range (400-700 nm). The measured optical band gap values of the ZnO thin films were between 3.26 eV and 3.28 eV, which were in the range of band gap values of intrinsic ZnO (3.2-3.3 eV). SEM analysis of annealed thin films has shown a completely different surface morphology behavior.     

Growth, structural and optical transport properties of nanocrystal Zn1−xCdS thin films deposited by solution growth technique (SGT) for photosensor applications

Solution Growth Technique (SGT) has been used for deposition of Zn_1−xCdS nanocrystalline thin films. Various parameters such as solution pH (10.4), deposition time, concentration of ions, composition and deposition and annealing temperatures have been optimized for the development of device grade thin film. In order to achieve uniformity and adhesiveness of thin film on glass substrate, 5 ml triethanolamine (TEA) have been added in deposition solution. The as-deposited films have been annealed in Rapid Thermal Annealing (RTA) system at various temperature ranges from 100 to 500 °C in air. The changes in structural formation and optical transport phenomena have been studied with annealing temperatures and composition value (x). As-deposited films have two phases of ZnS and CdS, which were confirmed by X-ray diffraction studies; further the X-ray analysis of annealed (380 °C) films indicates that the films have nanocrystalline size (150 nm) and crystal structure depends on the films stoichiometry and annealing temperatures. The Zn_0.4CdS films annealed at 380 °C in air for 5 min have hexagonal structure where as films annealed at 500 °C have represented the oxide phase with hexagonal structure. Optical properties of the films were studied in the wavelength range 350-1000 nm. The optical band gap (E_g=2.94-2.30 eV) decreases with the composition (x) value. The effect of air rapid annealing on the photoresponse has also been observed on Zn_1−xCdS nanocrystal thin films. The Zn_1−xCdS thin film has higher photosensitivity at higher annealing temperatures (380-500 °C), and films also have mixed Zn_1−xCdS/Zn_1−xCdSO phase with larger grain size than the as-deposited and films annealed up to 380 °C. The present results are well agreed with the results of other studies.     

Corrosion behavior of sputtered Cr-Si-Ni and Cr-Si-Ni-Al resistive films in 0.1 M NaOH

The corrosion behavior of magnetron sputtered Cr-Si-Ni and Cr-Si-Ni-Al resistive films had been investigated by means of the relative resistance change (ΔR/R), polarization measurements, AES, and SEM in 0.1 M NaOH solution at 25 °C and 50 °C, which simulated an alkaline environment. The results revealed that both the annealed Cr-Si-Ni and Cr-Si-Ni-Al films in Ar ambient exhibited good corrosion resistance and long-term reliability in 0.1 M NaOH solution at 25 °C, due to the formation of a protective oxide layer on the surface of two types of the films during corrosion. However, the corrosion properties of two types of the films became degraded rapidly with the solution temperature at 50 °C. The studies showed that the pro-formation of a protective oxide layer on the surface of two types of the films by annealing in air had an enhancing effect on the corrosion properties of the films in 0.1 M NaOH solution at 50 °C, and that Cr-Si-Ni-Al films by annealing in air had more improving effect on the corrosion resistance and long-term reliability than Cr-Si-Ni films.     

Effects of post-annealing on structural, optical and electrical properties of Al-doped ZnO thin films

Aluminum-doped zinc oxide (AZO) films were deposited at 400 °C by radio-frequency magnetron sputtering using a compound AZO target. The effects of annealing atmospheres as well as hydrogen annealing temperatures on the structural, optical and electrical properties of the AZO films were investigated. It was found that the electrical resistivity varied depending on the atmospheres while annealing in air, nitrogen and hydrogen at 300 °C, respectively. Comparing with that for the un-annealed films, the resistivity of the films annealed in hydrogen decreased from 9.8 × 10⁻⁴ Ω cm to 3.5 × 10⁻⁴ Ω cm, while that of the films annealed in air and nitrogen increased. The variations in electrical properties are ascribed to both the changes in the concentration of oxygen vacancies and adsorbed oxygen at the grain boundaries. These results were clarified by the comparatively XPS analyzing about the states of oxygen on the surface of the AZO films. There was great increase in electrical resistivity due to the damage of the surfaces, when AZO films were annealed in hydrogen with a temperature higher than 500 °C, but high average optical transmittance of 80-90% in the range of 390-1100 nm were still obtained.     

Effect of different annealing temperature on Sb-doped ZnO thin films prepared by pulsed laser deposition on sapphire substrates

Influence of annealing temperature on the properties of Sb-doped ZnO thin films were studied. Hall measurement results indicated that the Sb-doped ZnO annealed at 950 °C was p-type conductivity. X-ray diffraction (XRD) results indicated that the Sb-doped ZnO thin films prepared at the experiments are high c-axis oriented. It was worth noting that p-type sample had the worst crystallinity. The measurements of low-temperature photoluminescence (PL) spectra indicate that the sample annealed at the temperatures of 950 °C showed strong acceptor-bound exciton (A⁰X) emission, and confirmed that it is related to Sb-doping by comparing with the undoped ZnO low-temperature PL spectrum.     

Influence of annealing temperature on the properties of ZnO thin films deposited by thermal evaporation

ZnO thin films were deposited by thermal evaporation of a ZnO powder. The as-deposited films are dark brown, rich zinc and present a low transmittance. Then, these films were annealed in air atmosphere at different temperatures between 100 and 400 °C. Their microstructure and composition were studied using XRD and RBS measurements respectively. By increasing the temperature, it was found that film oxidation starts at 250 °C. XRD peaks related to ZnO appear and peaks related to Zn decrease. At 300 °C, zinc was totally oxidised and the films became totally transparent. The electrical conductivity measurement that were carried out in function of the annealing temperature showed the transition from highly conductive Zn thin film to a lower conductive ZnO thin film. The optical gap (E_g) was deduced from the UV-vis transmittance, and its variation was linked to the formation of ZnO.     

Investigation of p-type behavior in Ag-doped ZnO thin films by E-beam evaporation

Ag-doped ZnO (ZnO:Ag) thin films were grown on glass substrates by E-beam evaporation technique. The structural, electrical and optical properties of the films were investigated as a function of annealing temperature. The films were subjected to post annealing at different temperatures in the range of 350-650 °C in an air ambient. All the as grown and annealed films at temperature of 350 °C showed p-type conduction. The films lost p-type conduction after post annealing treatment temperature of above 350 °C, suggesting a narrow post annealing temperature window for the fabrication of p-type ZnO:Ag films. ZnO:Ag film annealed at 350 °C revealed lowest resistivity of 7.25 × 10⁻² Ω cm with hole concentration and mobility of 5.09 × 10¹⁹ cm⁻³ and 1.69 cm²/V s, respectively. Observation of a free-to-neutral-acceptor (e,A^o) and donor-acceptor-pair (DAP) emissions in the low temperature photoluminescence measurement confirms p-type conduction in the ZnO:Ag films.     

Effects of magnesium film thickness and annealing temperature on formation of Mg2Si films on silicon (1 1 1) substrate deposited by magnetron sputtering

Magnesium films of various thicknesses were first deposited on silicon (1 1 1) substrates by magnetron sputtering method and then annealed in annealing furnace filled with argon gas. The effects of the magnesium film thickness and the annealing temperature on the formation of Mg₂Si films were investigated by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM). The Mg₂Si thin films thus obtained were found to be polycrystalline and the Mg₂Si (2 2 0) orientation is preferred regardless of the magnesium film thickness and annealing temperature. XRD results indicate that high quality magnesium silicide films are produced if the magnesium/silicon samples are annealed at 400 °C for 5 h. Otherwise, the synthesized films annealed at annealing temperatures lower than 350 °C or higher than 450 °C contain magnesium crystallites or magnesium oxide. SEM images have revealed that microstructure grains in the polycrystalline films are about 1-5 μm in dimensions, and the texture of the Mg₂Si films becomes denser and more homogeneous as the thickness of the magnesium film increases.     

Characteristics of electron beam evaporated nanocrystalline SnO2 thin films annealed in air

Tin oxide (SnO₂) thin films (about 200 nm thick) have been deposited by electron beam evaporation followed by annealing in air at 350-550 °C for two hours. Optical, electrical and structural properties were studied as a function of annealing temperature. The as-deposited film is amorphous, while all other annealed films are crystalline (having tetragonal structure). XRD suggest that the films are composed of nanoparticles of 5-10 nm. Raman analysis and optical measurements suggest quantum confinement effects that are enhanced with annealing temperature. For instance, Raman peaks of the as-deposited films are blue-shifted as compared to those for bulk SnO₂. Blue shift becomes more pronounced with annealing temperature. Optical band gap energy of amorphous SnO₂ film is 3.61 eV, which increases to about 4.22 eV after crystallization. Two orders of magnitude decrease in resistivity is observed after annealing at 350-400 °C due to structural ordering and crystallization. The resistivity, however, increases slightly with annealing temperature above 400 °C, possibly due to improvement in stoichiometry and associated decrease in charge carrier density.     

Structural and optoelectronic properties of vacuum evaporated SnS thin films annealed in argon ambient

In this work, 650 nm polycrystalline SnS thin films were grown by thermal evaporation of high purity tin sulfide powder at 250 °C substrate temperature, followed by post deposition annealing at 200 °C and 300 °C for 2, 4 and 6 h, and at 400 °C for 2 and 4 h in argon ambient. The XRD pattern of the as-deposited and annealed SnS films led to the conclusion that the as-deposited films were polycrystalline in nature with preferentially oriented along (1 1 1) direction. The direct bandgap of all the films was found to be observed between 1.33 and 1.53 eV. Except for annealing at 400 °C all the films were nearly stoichiometric in nature, suggesting lower rate of desulfurization at that ambient. However, higher annealing temperature has resulted in the segregation of tin phase. All the films showed good absorption in the visible range. The as-deposited and annealed films showed p-type conductivity. Hall measurement revealed the carrier concentration and mobility ranging from 10¹⁵ to 10¹⁶ cm⁻³ and 0.8 to 31.6 cm² V⁻¹ s⁻¹ respectively. The photoconductivity measurements of all the SnS films were carried out by recording the lowering of resistance of the respective films with time under illumination.     

Preparation of p-type CdS thin films and in situ dark conductivity in vacuum deposited CdS:Cu films

CdS:Cu thin films were prepared using a vacuum co-evaporation technique. The Hall measurements indicate that the conductivity characteristic of CdS thin films transformed from highly compensated in as-grown or weakly annealed materials to p-type conductive in strongly annealed materials. X-ray diffraction spectra show that as-deposited thin films were the hexagonal phase of CdS except the presence of copper for high Cu doping and the diffraction peaks of Cu disappeared after annealing. From the X-ray photoelectron spectroscopy we found the ionization of Cu atoms and the formation of an acceptor level. In situ dark conductivity in vacuum as-deposited CdS:Cu was performed in the temperature range between 27 and 250 °C. An abnormal temperature dependence of conductivity was observed in medium and heavily Cu-doped films. The formation of a p-type material at a certain temperature was also studied by the hot probe measurements, which indicates a complex compensation process in the Cu-doped CdS films.     

Effects of annealing on morphological,structural and electrical properties of thermally evaporated WO3 thin films

Tungsten trioxide (WO₃) thin films were prepared by thermal evaporation method onto quartz substrates at room temperature. Effect of annealing temperature (from 200 to 800 °C) to morphology, crystallographic structure and electrical properties were investigated. In order to investigate the temperature dependant resistivity properties of the films dark current–voltage measurements were done at the temperatures of 30, 60, 90, 120 and 150 °C. From the AFM pictures it is seen that the increasing annealing temperature causes an increase in grain sizes. At elevated temperatures the grains combine to each other and thus form continuous and homogenous surfaces. From the XRD patterns it was seen that the as-prepared and annealed films at 200, 300, 310 and 320 °C were amorphous. On the other hand at 330 °C and higher temperatures the films were found as in crystallized structures (monoclinic phase). From the current–voltage measurements it was seen that the contacts areohmic and the current increased with increasing temperatures. From the calculated values it was seen that the produced films shows good semiconducting nature.     

Solution processed amorphous InGaZnO semiconductor thin films and transistors

Amorphous indium gallium zinc oxide (a-IGZO) semiconductor thin films and transistors were deposited on alkali-free glasses by the sol–gel route. The atomic ratio of In:Ga:Zn in the solution was 0.7:0.3:1. In this study, the effects of annealing temperature on the structural, surface condition, optical transmittance, and electrical resistivity of a-IGZO semiconductor thin films were investigated. GIXRD measurements and TEM-NBD analysis indicated that all annealed IGZO thin films had an amorphous phase structure. The dried IGZO sol–gel films annealed at a temperature higher than 425 °C had a flat surface and exhibited high transparency (>89%) in the visible region. According to results from TGA, FT-IR and XPS, the residual organic compounds in the dried IGZO sol–gel films were completely removed at the annealing temperatures higher than 450 °C. Therefore, we chose the 450 °C annealed thin film as the active channel layer in the bottom-gate, bottom-contact (BGBC) thin-film transistor (TFT) in the present study. Current–voltage (I–V) characteristics of the 450 °C annealed a-IGZO TFT revealed that it operated in n-type behavior with a positive threshold voltage (enhancement mode).     

Post-annealing effect upon optical properties of electron beam evaporated molybdenum oxide thin films

Molybdenum oxide (MoO₃) thin films were deposited by electron beam evaporation. The chemical composition, microstructure, optical and electrical properties of MoO₃ thin films depend on the annealing temperature and ambient atmosphere. X-ray diffraction (XRD) shows that crystalline MoO₃ films can be obtained at various post-annealing temperatures from 200 to 500 °C in N₂ and O₂. X-ray photoelectron spectroscopy (XPS) results reveal that the O-1s emission peak was shifted slightly toward lower binding energies as the annealing temperature in N₂ was increased. The oxygen vacancies and conductivity of MoO₃ film increased with the annealing temperature. However, when the MoO₃ films were annealed in an atmosphere of O₂, the optical transmission, the O/Mo ratio and the photon energy increased with the annealing temperature. The results differ from those for films annealed in a N₂ atmosphere.     

Crystallization and electrochemical performance of La0.6Sr0.4Co0.2Fe0.8O3 − δ-Ce0.8Gd0.2O1.9 thin film cathodes processed by single solution spray pyrolysis

La_0.6Sr_0.4Co_0.2Fe_0.8O_3 − δ-Ce_0.8Gd_0.2O_1.9 (LSCF-CGO) thin films obtained by spray pyrolysis of a single precursor solution were investigated by XRD, TEM and impedance spectroscopy at annealing temperatures ranging from 500 to 900 °C. Films annealed at 600 °C contained a mixture of amorphous regions and crystalline regions composed of fine crystallites (< 5 nm). Annealing above 600 °C increased the ratio of crystalline to amorphous material, led to the segregation of the films into distinct LSCF and CGO phases, and promoted grain growth. The electrical behavior of the films depended on annealing temperature. At testing temperatures of 400 °C and below, the polarization resistance of films with lower annealing temperatures was larger than the polarization resistance of films with higher annealing temperatures. However, at testing temperatures of 500 °C and above the polarization resistance of films with lower annealing temperatures was equal to or lower than the polarization resistance of films with higher annealing temperatures. This was reflected by the activation energy that decreased with increasing annealing temperature. The varying electrical behavior may be related to microstructural changes that caused bulk diffusion to be the rate-limiting step in films with lower annealing temperatures and oxygen dissociation to be the rate-limiting step in films with higher annealing temperatures.