Transparent conductive ZnO:Ga films prepared by DC reactive magnetron sputtering at low temperature

Ga-doped ZnO (ZnO:Ga) transparent conductive films were deposited on glass substrates by DC reactive magnetron sputtering. The structural, electrical, and optical properties of ZnO:Ga films were investigated in a wide temperature range from room temperature up to 400 °C. The crystallinity and surface morphology of the films are strongly dependent on the growth temperatures, which in turn exert an influence on the electrical and optical properties of the ZnO:Ga films. The film deposited at 350 °C exhibited the relatively well crystallinity and the lowest resistivity of 3.4 × 10⁻⁴ Ω cm. More importantly, the low-resistance and high-transmittance ZnO:Ga films were also obtained at a low temperature of 150 °C by changing the sputtering powers, having acceptable properties for application as transparent conductive electrodes in LCDs and solar cells.     

Deposition of Ni, Ag, and Pt-based Al-doped ZnO double films for the transparent conductive electrodes by RF magnetron sputtering

Ni, Ag, and Pt-based Al-doped ZnO (AZO) films have been deposited as transparent conductivity layers on quartz by RF magnetron sputtering and characterized by X-ray diffraction, Hall measurement, optical transmission spectroscopy, scanning electron microscopy (SEM). The deposition of thicker metal layer in double layers resulted in lowering the effective electrical resistivity with a slight reduction of their optical transmittance. A film consisting of AZO (250 nm)/Ni (2 nm) double structure, exhibits a sheet resistance of 21.0 Ω/sq, a high transmittance of 76.5%, and characterize good adhesion to substrate. These results make the satisfactory for GaN-based light-emitting diodes (LEDs) and solar cells with metal-based AZO double films as current spread layers.     

Influence of negative ion resputtering on Al-doped ZnO thin films prepared by mid-frequency magnetron sputtering

Al-doped ZnO (AZO) films were deposited on glass substrates by mid-frequency magnetron sputtering with a ceramic ZnO:Al₂O₃ (98 wt%:2 wt%) target. The origin of the high resistivity of the films at the substrate position facing the erosion area of the target was investigated. The results indicate a preferential resputtering of Zn atoms caused by the negative ions, which leads to an increase of the oxygen/metal ratio in the films. Then more Al oxides form and result in the decrease of Al_Zn (the main donor in the films) concentration in the films. Thus the free carrier concentration decreases badly. This is the main mechanism responsible for the high resistivity.     

Optimization of parameters for deposition of Ga-doped ZnO films by DC reactive magnetron sputtering using Taguchi method

Ga-doped ZnO (ZnO:Ga) transparent conductive films were deposited on glass substrates by DC reactive magnetron sputtering. Taguchi method was used to find the optimal deposition parameters including oxygen partial pressure, argon partial pressure, substrate temperature, and sputtering power. By employing the analysis of variance, we found that the oxygen and argon partial pressures were the most influencing parameters on the electrical properties of ZnO:Ga films. Under the optimized deposition conditions, the ZnO:Ga films showed acceptable crystal quality, lowest electrical resistivity of 2.61 × 10⁻⁴ Ω cm, and high transmittance of 90% in the visible region.     

Growth of Ga-doped ZnO films with ZnO buffer layer by sputtering at room temperature

Gallium-doped zinc oxide films have been grown on glass substrates with and without ZnO buffer layers by r.f. magnetron sputtering at room temperature. In this approach, the grey relational Taguchi method analysis is adopted to solve the coating process with multiple deposition qualities. Optimal coating parameters can then be determined by using the gray relational grade as a performance index. The GZO coating parameters (r.f. power, sputtering pressure, O₂/(Ar+O₂) flow-rate ratios, and deposition time) are optimized, by taking into account the multiple performance characteristics (structural, morphological, deposition rate, electrical resistivity, and optical transmittance). The results indicate that with the grey relational Taguchi method, the electrical resistivity of GZO films is reduced from 9.23×10⁻³ to 5.77×10⁻³ Ω cm and optical transmittance increases from 79.42% to 82.95%, respectively. The ZnO buffer layer can reduce the electrical resistivity of GZO films from 5.77×10⁻³ to 2.38×10⁻³ Ω cm. It can be anticipated that room temperature deposition enables film deposition onto polymeric substrates for flexible optoelectronic devices.     

磁控溅射制备ZnO薄膜及其声表面波特性

通过射频磁控溅射技术在GaAs，Au/GaAs，Si和玻璃基片上成功制备了ZnO多晶薄膜，利用X射线衍射对ZnO薄膜的取向、结晶性进行了表征，结果表明ZnO薄膜呈完全c轴取向，Au缓冲层可以有效地改善ZnO薄膜的晶体质量，X射线摇摆曲线结果表明ZnO(002)衍射峰的半高宽仅为2.41°，同时发现Au缓冲层的结晶质量对ZnO薄膜的c轴取向度有很大影响，通过扫描电子显微镜对ZnO/GaAs和ZnO/Au/GaAs薄膜的表面形貌进行了观测，利用网络分析仪对IDT/ZnO/GaAs薄膜的声表面波特性进行了测量. 关键词： ZnO薄膜 X射线衍射 声表面波     

Influence of deposition temperature on the crystallinity of Al-doped ZnO thin films at glass substrates prepared by RF magnetron sputtering method

Al-doped ZnO (AZO) transparent conducting films were successfully prepared on glass substrates by RF magnetron sputtering method under different substrate temperatures. The microstructural, electrical and optical properties of AZO films were investigated in a wide temperature range from room temperature up to 350 °C by X-ray Diffraction (XRD), Field-Emission Scanning Electron Microscopy (FESEM), High-Resolution Transmission Electron Microscopy (HRTEM), Hall measurement, and UV–visible meter. The nature of AZO films is polycrystalline thin films with hexagonal wurtzite structure and a preferred orientation along c-axis. The crystallinity and surface morphologies of the films are strongly dependent on the growth temperature, which in turn exerts a great effect on microstructural, electrical and optical properties of the AZO films. The atomic arrangement of AZO film having an wurtzite structure was indeed identified by the HRTEM as well as the Selected Area Electron Diffraction (SAED). The defect density of AZO film was investigated by HRTEM. The film deposited at 100 °C exhibited the relatively well crystallinity and the lowest resistivity of 3.6 × 10⁻⁴ Ω cm. The average transmission of AZO films in the visible range is all over 85%. More importantly, the low-resistance and high-transmittance AZO film was also prepared at a low temperature of 100 °C.     

The transparence comparison of Ga- and Al-doped ZnO thin films

The Ga-doped ZnO (GZO) and Al-doped ZnO (AZO) thin films were grown on quartz glass substrates by pulsed laser deposition under different oxygen partial pressures (PO₂). The transparent performances of films versus properties of structure and conductivity were discussed. With the increase of PO₂, the transmittance of both GZO films and AZO films increased to maximum and then decreased which were in according with the change of crystallization quality. The transmittance of GZO films was higher than that of AZO films, which were not dominated by the impurity ions induced by doping. AFM images and surface roughness mean square coefficients showed that the surfaces of GZO films were smoother than that of AZO films, which were due to the dopant Ga acting as the surfactant and smoothed the GZO films surface.     

High-performance InGaN/GaN MQW LEDs with Al-doped ZnO transparent conductive layers grown by MOCVD using H_2O as an oxidizer

In this study,the high performance of InGaN/GaN multiple quantum well light-emitting diodes(LEDs) with Aldoped ZnO(AZO) transparent conductive layers(TCLs) has been demonstrated.The AZO-TCLs were fabricated on the n~+-InGaN contact layer by metal organic chemical vapor deposition(MOCVD) using H_2O as an oxidizer at temperatures as low as 400 ℃ without any post-deposition annealing.It shows a high transparency(98%),low resistivity(510 ~4 Ω·cm),and an epitaxial-like excellent interface on p-GaN with an n+-InGaN contact layer.A forward voltage of 2.82 V @ 20 mA was obtained.Most importantly,the power efficiencies can be markedly improved by 53.8%@20 mA current injection and 39.6%@350 mA current injection compared with conventional LEDs with indium tin oxide TCL(LED-Ⅲ),and by28.8%@20 mA current injection and 4.92%@350 mA current injection compared with LEDs with AZO-TCL prepared by MOCVD using O_2 as an oxidizer(LED-Ⅱ),respectively.The results indicate that the AZO-TCL grown by MOCVD using H_2O as an oxidizer is a promising TCL for a low-cost and high-efficiency GaN-based LED application.     

The field emission of indium-doped ZnO films fabricated by room temperature DC magnetron sputtering

Indium doped ZnO film was fabricated at room temperature by co-sputtering a zinc target and an indium plate under the flow of oxygen and argon. The film was then characterized and the field emission of the film was studied. The indium composition x in the film (Zn_1−xIn_xO) is 5%. The film is hexagonal without any secondary phases or precipitates. The film has two major emission peaks, one related to the band edge emission and another possibly related to the electron acceptor transition. The possible acceptor is nitrogen occupying oxygen site in ZnO. The film is n-type and very resistive. The turn on field of the film at an emission current density of 10 μA/cm² is 17.5 V/μm. The relatively weak field emission property is due to the unintentional incorporation of acceptors such as substitutional nitrogen and oxygen vacancies, which increase the work function of ZnO by reducing the electron density and lowering the Fermi level position of the ZnO:In film.     

Defects related room temperature ferromagnetism in p-type (Mn, Li) co-doped ZnO films deposited by reactive magnetron sputtering

We report on the defects related room temperature ferromagnetic characteristics of Zn_0.95-xMn_xLi_0.05O (x = 0.01, 0.03, 0.05 and 0.08) thin films grown on glass substrates using reactive magnetron sputtering. By increasing the Mn content, the films exhibited increases in the c-axis lattice constant, fundamental band gap energy, coercive field and remanent magnetization. Comparison of the structural and magnetic properties of the as-deposited and annealed films indicates that the hole carriers, together with defects concentrations, play an important role in the ferromagnetic origin of Mn and Li co-doped ZnO thin films. The ferromagnetism in films can be described by bound magnetic polaron models with respect to defect-bound carriers.     

Effects of sapphire substrates surface treatment on the ZnO thin films grown by magnetron sputtering

The surface treatment effects of sapphire substrate on the ZnO thin films grown by magnetron sputtering were studied. The sapphire substrates properties have been investigated by means of atomic force microscopy (AFM) and X-ray diffraction rocking curves (XRCs). The results show that sapphire substrate surfaces have the best quality by CMP with subsequent chemical etching. The surface treatment effects of sapphire substrate on the ZnO thin films were examined by X-ray diffraction (XRD) and photoluminescence (PL) measurements. Results show that the intensity of (0 0 2) diffraction peak of ZnO thin films on sapphire substrates treated by CMP with subsequent chemical etching was strongest, FWHM of (0 0 2) diffraction peak is the narrowest and the intensity of UV peak of PL spectrum is strongest, indicating surface treatment on sapphire substrate preparation may improve ZnO thin films crystal quality and photoluminescent property.     

Transparent conductive ITO/Ag/ITO multilayer electrodes deposited by sputtering at room temperature

ITO/Ag/ITO multilayers have been prepared onto conventional soda lime glass substrates by sputtering at room temperature. The optical and electrical characteristics of single layer and multilayer structures have been investigated as a function of the Ag and ITO film thicknesses. Transmittance and sheet resistance values are found mainly dependent on the Ag film thickness; whereas the wavelength range at which the maximum transmittance is achieved can be changed by adjusting the ITO films thickness. ITO/Ag/ITO electrodes with sheet resistance below 6 Ω/sq have been obtained for Ag film thickness above 10 nm and ITO layers thickness in the 30-50 nm range. These multilayers also show high transmittance in the visible spectral region, above 90% by discounting the glass substrate, with a maximum that is located at higher wavelengths for thicker ITO.     

The influence of annealing on the properties of ZnO:Al layers obtained by RF magnetron sputtering

Al doped ZnO has been explored as a viable alternative to indium thin oxide, which is usually used as transparent electrodes' coverage but is expensive. Homogenous and durable ZnO:Al layers on glass have been obtained in radio frequency magnetron sputtering system by adjusting optimized deposition parameters, using ZnO ceramic target with 2?wt% Al₂O₃. Then, after growth process, annealing treatment has been introduced in order to improve the quality of the layers. Structural, electrical and optical properties of the obtained ZnO:Al layers are presented and discussed. From the application point of view, the best results (sheet resistance of 24 Ω/sq and transparency well above 85%) were achieved after annealing in 300?°C.     

Effects of hydrogen flux on the properties of Al-doped ZnO films sputtered in Ar + H2 ambient at low temperature

Al-doped ZnO (AZO) transparent conductive thin films were grown by magnetron sputtering with AZO (98 wt.% ZnO, 2 wt.% Al₂O₃) ceramic target in Ar + H₂ ambient at a relatively low temperature of 100 °C. To investigate the dependence of crystalline and properties of as-grown AZO films on the H₂-flux, X-ray diffraction (XRD), X-ray photoemission spectrometer (XPS), Hall and transmittance spectra measurements were employed to analyze the AZO samples deposited with different H₂-flux. The results indicate that H₂-flux has a considerable influence on the transparent conductive properties of AZO films. The resistivity of 4.15 × 10⁻⁴ Ω cm and the average transmittance of more than 94% in the visible range were obtained with the optimal H₂-flux of 1.0 sccm. Such a low temperature growing method present here may be especially useful for some low-melting point photoelectric devices and substrates.     

磁控溅射法制备钴掺杂氧化锌薄膜室温磁学性质

钴掺杂氧化锌是室温稀磁半导体的重要候选材料,其磁学特性和钴掺杂浓度、显微结构及光学性质密切相关。磁控溅射具有成本低、易于大面积沉积高质量薄膜等特点,是广受关注的稀磁半导体薄膜制备方法。利用磁控溅射方法制备了不同浓度的钴掺杂氧化锌薄膜,并对其显微结构、光学性质和磁学特性进行了系统分析。结果表明：当掺杂原子分数在8%以内时,钴掺杂氧化锌薄膜保持单一的铅锌矿晶体结构,钴元素完全溶解在氧化锌晶格之中;薄膜在可见光区域有很高的透射率,但在567, 615和659 nm处有明显吸收峰,这些吸收峰源于Co2+处于O2-形成的四面体晶体场中的特征d-d跃迁。磁学特性测试结果表明钴掺杂氧化锌薄膜具有室温铁磁性,且钴的掺杂浓度对薄膜的磁学特性有重要影响。结合薄膜结构、光学和电学性质分析,实验中观察到的室温铁磁性应源于钴掺杂氧化锌薄膜的本征属性,其铁磁耦合机理可由束缚磁极化子模型进行解释。     

Electrical and optical properties of Al-doped ZnO thin films by sol-gel process

Al-doped ZnO (AZO) thin films oriented along the (0 0 2) plane have been prepared by the sol-gel process and their electrical and optical properties with post-deposition heating temperature were investigated. The preferred c-axis orientation along the (0 0 2) plane was enhanced with increasing post-deposition heating temperature and the surface of the films showed a uniform and nano-sized microstructure. The electrical resistivity of the films decreased from 73 to 22 Ω cm as the post-deposition heating temperature increased from 500 to 650 °C; however, the film postheated at 700 °C increased greatly to 580 Ω cm. The optical transmittance of the films postheated below 650 °C was over 86%, but it decreased at 700 °C. The electrical and optical properties of the AZO films with post-deposition heating temperature are discussed.     

Fast response ultraviolet photoconductive detectors based on Ga-doped ZnO films grown by radio-frequency magnetron sputtering

A metal-semiconductor-metal photoconductive detector was fabricated on c-axis preferred oriented Ga-doped ZnO (ZnO:Ga) thin film prepared on quartz by radio-frequency magnetron sputtering. With a 10 V bias, a responsivity of about 2.6 A/W at 370 nm was obtained in the ultraviolet region. The photocurrent increases linearly with incident power density for more than two orders of magnitude. The transient response measurement revealed photoresponse with a rise time of 10 ns and a fall time of 960 ns, respectively. The results are much faster than those reported in photoconductive detectors based on unintentionally doped n-type ZnO films.     

Characteristics of ZnO:In thin films prepared by RF magnetron sputtering

In-doped ZnO (ZnO:In) transparent conductive thin films were deposited on glass substrates by RF magnetron sputtering. The effect of substrate temperature on the structural, electrical and optical properties of the ZnO:In thin films was investigated. It was found that higher temperature improves the crystallinity of the films and promotes In substitution easily. ZnO:In thin films with the best crystal quality were fabricated at 300 °C, which exhibit a larger grain size of 29 nm and small tensile strain of 0.9%. The transmittance of all the films was revealed to be over 85% in the visible range independence of the substrate temperatures and the lowest resistivity of ZnO:In thin films is 2.4×10⁻³ Ω cm.