SnO2:Eu nanoparticles dispersed in silica: A low-temperature synthesis and photoluminescence study

SnO₂:Eu and SnO₂:Eu nanoparticles dispersed in silica matrix were prepared at a relatively low temperature of 185 °C in ethylene glycol medium. For as-prepared SnO₂:Eu nanoparticles there exists a weak energy transfer from the SnO₂ host to the Eu³⁺ ions. However, the energy transfer can be significantly improved by dispersing the Eu³⁺-doped SnO₂ nanoparticles in silica matrix. Effective shielding of surface Eu³⁺ ions in SnO₂:Eu nanoparticles from the stabilizing ligand by silica matrix is the reason for the improved extent of energy transfer. Increase in asymmetric ratio of luminescence (ratio of the intensity of the electric dipole allowed transition, ⁵D₀→⁷F₂, to magnetic dipole allowed transition, ⁵D₀→⁷F₁) for SnO₂:Eu nanoparticles dispersed in silica compared to that of SnO₂:Eu nanoparticles, has been attributed to the distorted environment around surface Eu³⁺ ions brought about by the presence of both tin and silicon structural units. ¹¹⁹Sn and ²⁹Si MAS NMR studies on this sample confirmed that there is no interaction between the tin and silicon structural units even after heating the samples at 900 °C.     

Influence of CuO catalyst in the nanoscale range on SnO2 surface for H2S gas sensing applications

The dispersal of CuO catalyst on the surface of the semiconducting SnO₂ film is found to be of vital importance for improving the sensitivity and the response speed of a SnO₂ gas sensor for H₂S gas detection. Ultra-thin CuO islands (8 nm thin and 0.6 mm diameter) prepared by evaporating Cu through a mesh and subsequent oxidation yield a fast response speed and recovery. Ultimately nanoparticles of Cu (average size = 15 nm) prepared by a chemical technique using a reverse micelle method involving the reduction of Cu(NO₃)₂ by NaBH₄ exhibited significant improvement in the gas sensing characteristics of SnO₂ films. A fast response speed of ∼14 s and a recovery time of ∼60 s for trace level ∼20 ppm H₂S gas detection have been recorded. The sensor operating temperature (130° C) is low and the sensitivity (S = 2.06 × 10³) is high. It is found that the spreading over of CuO catalyst in the nanoscale range on the surface of SnO₂ allows effective removal of excess adsorbed oxygen from the uncovered SnO₂ surface due to spill over of hydrogen dissociated from the H₂S-CuO interaction.     

Carbon-coated SnO2 nanobelts and nanoparticles by single catalytic step

Several types of carbon nanostructures (amorphous and graphitic), for the coating of SnO₂ nanobelts and nanoparticles were obtained by a single catalytic process, during methane, natural gas, and methanol decomposition using the reactivity of surface-modified SnO₂ nanostructure as a nanotemplate. The nanostructured catalyst templates were based on transition metal nanoparticles supported on SnO₂ nanobelts previously prepared by a carbothermal reduction process. Carbon-coated SnO₂ nanopowders were also successfully synthesized for the fabrication of carbon spheres. The carbon coating process and yield, along with the nature of the nanostructured carbon, are strongly influenced by the chemically modified surface of the SnO₂ nanostructure template and the chemical reaction gas composition. The preliminary catalytic activity and gas-sensing properties of these novel materials based on metal nanoparticles and carbon-coated SnO₂ were determined.     

SnO$lt;sub$gt;2$lt;/sub$gt;纳米晶体的制备、结构与发光性质

使用软化学方法在碱性溶液中制备出了颗粒尺寸分布均匀的SnO₂纳米颗粒,使用透射电子显微镜（TEM）、X射线衍射（XRD）、光致发光谱（PL）和光吸收谱等方法分析与表征了SnO₂纳米颗粒的结构和光学性能.实验中通过表面活性剂的加入来控制纳米颗粒的结晶与凝聚.XRD,TEM的结果表明,原始制备出的SnO₂纳米颗粒的平均粒径小于4 nm,为完好的晶体状态.纳米颗粒经过400—1000 ℃退火后晶粒尺寸进一步增大.光吸收谱表明,相对于体材料,纳米颗粒的禁带宽度展宽并随颗粒尺寸增大而红移.光致发光谱测试表明,不同温度下退火的SnO₂纳米颗粒在350—750 nm有较强的发光,研究表明这是来源于颗粒表面的氧空位缺陷发光. 关键词： 氧化锡 表面活性剂 纳米颗粒 光致发光     

Structural and crystal growth kinetics studies for SnO2 nanoparticles prepared via hydrothermal route

Tin oxide nanoparticles with crystallite size (1.9–3 nm) were synthesized via hydrothermal route. The role of autoclave temperature (T_A) on the structural parameters and surface morphology of the as-synthesized SnO₂ nanoparticles (NPs) was followed using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The thermal behavior of the as-synthesized SnO₂ NPs was carried out using thermogravimetric and differential thermal analysis (TGA/DTA) techniques under non-isothermal conditions. The effect of T_A on the activation energy of crystal growth (E_c) and the Avrami exponent (n) of SnO₂ NPs were determined by different methods. The reaction mechanism controlling the growth process was discussed in terms of the results obtained using different iso-conversional methods to determine the local E_c(α) and n(α).     

The improvement of gas-sensing properties of SnO<Subscript>2</Subscript>/zeolite-assembled composite

SnO₂-impregnated zeolite composites were used as gas-sensing materials to improve the sensitivity and selectivity of the metal oxide-based resistive-type gas sensors. Nanocrystalline MFI type zeolite (ZSM-5) was prepared by hydrothermal synthesis. Highly dispersive SnO₂ nanoparticles were then successfully assembled on the surface of the ZSM-5 nanoparticles by using the impregnation methods. The SnO₂ nanoparticles are nearly spherical with the particle size of ~?10 nm. An enhanced formaldehyde sensing of as-synthesized SnO₂-ZSM-5-based sensor was observed whereas a suppression on the sensor response to other volatile organic vapors (VOCs) such as acetone, ethanol, and methanol was noticed. The possible reasons for this contrary observation were proposed to be related to the amount of the produced water vapor during the sensing reactions assisted by the ZSM-5 nanoparticles. This provides a possible new strategy to improve the selectivity of the gas sensors. The effect of the humidity on the sensor response to formaldehyde was investigated and it was found the higher humidity would decrease the sensor response. A coating layer of the ZSM-5 nanoparticles on top of the SnO₂-ZSM-5-sensing film was thus applied to further improve the sensitivity and selectivity of the sensor through the strong adsorption ability to polar gases and the “filtering effect” by the pores of ZSM-5.     

Synthesis and characterization of a polyaniline-modified SnO<Subscript>2</Subscript> nanocomposite

Polyaniline-modified tin oxide and tin oxide nanoparticles were synthesized using a solution route technique. The obtained pristine products were characterized with X-ray diffraction, thermogravimetric analysis, scanning electron microscopy, and optical absorption spectroscopy. Thermogravimetric analysis results showed that the polyaniline-modified SnO₂ nanoparticles exhibit higher thermal stability than the SnO₂ nanoparticles. Scanning electron microscopy analysis on the as-synthesized powders showed spherical particle in the range of 50–100 nm.     

Effect of annealing on electrical resistivity of rf-magnetron sputtered nanostructured SnO2 thin films

Tin oxide (SnO₂) thin films were deposited by radio frequency (RF) magnetron sputtering on clean corning glass substrates. These films were then annealed for 15 min at various temperatures in the range of 100-500°C. The films were investigated by studying their structural and electrical properties. X-ray diffraction (XRD) results suggested that the deposited SnO₂ films were formed by nanoparticles with average particle size in the range of 23-28 nm. XRD patterns of annealed films showed the formation of small amount of SnO phase in the matrix of SnO₂. The initial surface RMS roughness measured with atomic force microscopy (AFM) was 25.76 nm which reduces to 17.72 nm with annealing. Electrical resistivity was measured as a function of annealing temperature and found to lie between 1.25 and 1.38 mΩ cm. RMS roughness and resistivity show almost opposite trend with annealing.     

Electrical, structural and surface properties of fluorine doped tin oxide films

Fluorine (F) incorporated polycrystalline SnO₂ films have been deposited onto glass substrates by ultrasonic spray pyrolysis technique. To possess information about the electrical properties of all films, their electrical conductivities were investigated depending on the temperature, and their activation and trap energies were analyzed. The crystalline structure, surface properties and elemental analysis of the SnO₂ films were examined to determine the effect of the F element. After all investigations, it was concluded that each fluorine incorporation rate has a different and important effect on the physical properties, and SnO₂:F (3 at%) films were found to be the most promising sample for energy conversion devices, especially as conducting electrode in solar cells with its improved structural and electrical properties as compared to others.     

Preparation of nanocrystalline Sn-TiO2−X via a rapid and simple stannous chemical reducing route

The Sn-TiO_2−X nanoparticles have been prepared via a rapid and simple stannous chemical reducing method. The as-prepared Sn-TiO_2−X nanoparticles were investigated by means of surface photovoltage spectroscopy (SPS), XPS, and DRS technology as well as photocatalytic degradation of RhB were studied under illumination. The experiment results revealed that the reduction of the TiO₂ particles raised their Fermi level, which can enhance the driven force of photoinduced electrons transferring from TiO₂ to adsorbed O₂ and SnO₂ on the surface of TiO₂. On the other hand, the amount of oxygen vacancies of the Sn-TiO_2−X increased after the stannous chemical reduction. The oxygen vacancies can also effectively inhibit the recombination of photoinduced electrons and holes pairs. These factors are favorable to the photocatalytic reaction.     

Silica-based composite and mixed-oxide nanoparticles from atmospheric pressure flame synthesis

Binary TiO₂/SiO₂ and SnO₂/SiO₂ nanoparticles have been synthesized by feeding evaporated precursor mixtures into an atmospheric pressure diffusion flame. Particles with controlled Si:Ti and Si:Sn ratios were produced at various flow rates of oxygen and the resulting powders were characterized by BET (Brunauer–Emmett–Teller) surface area analysis, XRD, TEM and Raman spectroscopy. In the Si–O–Ti system, mixed oxide composite particles exhibiting anatase segregation formed when the Si:Ti ratio exceeded 9.8:1, while at lower concentrations only mixed oxide single phase particles were found. Arrangement of the species and phases within the particles correspond to an intermediate equilibrium state at elevated temperature. This can be explained by rapid quenching of the particles in the flame and is in accordance with liquid phase solubility data of Ti in SiO₂. In contrast, only composite particles formed in the Sn–O–Si system, with SnO₂ nanoparticles predominantly found adhering to the surface of SiO₂ substrate nanoparticles. Differences in the arrangement of phases and constituents within the particles were observed at constant precursor mixture concentration and the size of the resultant segregated phase was influenced by varying the flow rate of the oxidant. The above effect is due to the variation of the residence time and quenching rate experienced by the binary oxide nanoparticles when varying the oxygen flow rate and shows the flexibility of diffusion flame aerosol reactors.     

Controllable synthesis and highly efficient electrocatalytic oxidation performance of SnO2/CNT core-shell structures

In this work, the nanocomposites, carbon nanotubes (CNTs) coated with nanosized uninterrupted SnO₂, were prepared controllably by a facile solvothermal method. The obtained nanocomposites have a thin overlayer which is made of nanoparticles with a diameter of ∼3 nm. The products were characterized by X-ray diffraction and transmission electron microscopy. The obtained SnO₂/CNTs have an excellent electrocatalytic oxidation performance for the X-3B, a kind of dye. The parameters affecting the electrocatalytic activity were investigated in details. The excellent catalytic property of the SnO₂/CNT electrodes can be explained as follows: (1) high specific surface area gives more active sites for X-3B oxidation; (2) the formation of thin, uniform, and uninterrupted coverage of SnO₂ nanoparticles on CNTs raises the potential of oxygen evolution and the current efficiency; and (3) the CNTs increase the conductivity of the electrodes, which results in the increase of the current efficiency.     

The Stabilization of Metal Oxide Nanocrystals by the Addition of Alumina

A problem in the study of nanoparticles is that they will tend to grow at moderate temperatures. For example, most oxides (e.g. SnO₂, ZrO₂, MgO) will show significant grain growth at 400°C. This severely limits experimental studies that require measurements over an extensive temperature range. In this contribution we demonstrate that the incorporation of A1₂O₃, can significantly restrict grain growth in MgO and ZrO₂ even at high temperatures.     

Pure and Sb-doped SnO 2 nanoparticles studied by photoelectron spectroscopy

We describe photoemission results from pure and Sb-doped SnO₂ nanoparticles deposited on gold substrates. Photoelectron spectra with synchrotron radiation were recorded for Sn 3d, Sb 3d and O 1s core levels and valence bands in the 500-1200 eV energy range. For pure SnO₂ nanoparticles the surface is terminated by an oxygen rich layer with no obvious surface environment for Sn. When doped n-type with 9.1% or 16.7% Sb, dopant atoms are concentrated near the surface of the nanoparticles. The valence state of the dopant atoms is predominantly Sb^V. Plasmon satellite features are also observed in core level photoemission spectra and their intensity relative to the main peak increases with increasing photon energy. Received 30 November 2000     

Facile and surfactant-free synthesis of SnO<Subscript>2</Subscript>-graphene hybrids as high performance anode for lithium-ion batteries

A facile microwave-assisted ethylene glycol method is developed to synthesize the SnO₂ nanoparticles dispersed on or encapsulated in reduced graphene oxide (SnO₂-rGO) hybrids. The morphology, structure, and composition of SnO₂-rGO are investigated by scanning electron microscopy, transmission electron microscope, thermo-gravimetric analyzer, X-ray diffraction, Raman spectroscopy, and X-ray photoelectron spectroscopy. The electrochemical performance of SnO₂-rGO as anode materials for lithium-ion batteries was tested by cyclic voltammetry, galvanostatic charge–discharge cycling, and rate capability test. It is found that the SnO₂ nanoparticles with a uniform distribution have p-type doping effect with rGO nanosheets. The as-prepared SnO₂-rGO hybrids exhibit remarkable lithium storage capacity and cycling stability, and the possible mechanism involved is also discussed. Their capacity is 1222 mAhg^?1 in the first cycle and maintains at 700 mAhg^?1 after 100 cycles. This good performance can be mainly attributed to the unique nanostructure, good structure stability, more space for volume expansion of SnO₂, and mass transfer of Li⁺ during cycling.     

The effect of surfactants on the magnetic and optical properties of Co-doped SnO2 nanoparticles

A series of Co-doped SnO₂ nanoparticles have been synthesized by the co-precipitation route. Different amounts of surfactant have been used in order to study the effect of surfactants (CTAB) on the magnetic and optical properties. Structural analyses reveal that Co dopants are substituted into rutile SnO₂ nanoparticles without forming any secondary phase. The increase of the surfactant promotes the adsorption of organic molecules on the surfaces of nanoparticles. Meanwhile, both the ferromagnetism and the orange emission drop progressively. The dependence of ferromagnetic properties on the surfactant concentration could be explained based on the bound magnetic polaron, where the carriers are provided by oxygen vacancies. XANES spectra reveal that the electrons transfer from Co 3d bands to the surfactant ions. Such electron-transfer process suppresses the formation of oxygen vacancies and leads to the decline of the ferromagnetism and optical emission.     

Facile synthesis and optical property of SnO2 flower-like architectures

Two-dimensional (2D) hierarchical tin dioxide (SnO₂) flower-like architectures consisting of sheet-like nanoparticles have been successfully prepared by a simply mild hydrothermal method based on the reaction between tin foil, NaOH and KBrO₃. The photoluminescence (PL) spectrum exhibit that the flower-like architectures of SnO₂ have strong PL emission, which suggest its possible applications in nanoscaled optoelectronic devices. The formation process of SnO₂ architectures is investigated and the corresponding mechanism is also proposed.     

Sensing low concentrations of CO using flame-spray-made Pt/SnO2 nanoparticles

Tin dioxide nanoparticles of different sizes and platinum doping contents were synthesized in one step using the flame spray pyrolysis (FSP) technique. The particles were used to fabricate semiconducting gas sensors for low level CO detection, i.e. with a CO gas concentration as low as 5 ppm in the absence and presence of water. Post treatment of the SnO₂ nanoparticles was not needed enabling the investigation of the metal oxide particle size effect. Gas sensors based on tin dioxide with a primary particle size of 10 nm showed signals one order of magnitude higher than the ones corresponding to the primary particle size of 330 nm. In situ platinum functionalization of the SnO₂ during FSP synthesis resulted in higher sensor responses for the 0.2 wt% Pt-content than for the 2.0 wt% Pt. The effect is mainly attributed to catalytic consumption of CO and to the associated reduced sensor response. Pure and functionalized tin dioxide nanoparticles have been characterized by Brunauer, Emmett and Teller (BET) surface area determination, X-ray diffraction (XRD), high resolution transmission electron microscopy (HRTEM) and scanning transmission electron microscopy (STEM) while the platinum oxidation state and dispersion have been investigated by X-ray photoelectron spectroscopy (XPS) and extended X-ray absorption fine structure (EXAFS). The sensors showed high stability (up to 20 days) and are suitable for low level CO detection: <10 ppm according to European and 50 ppm according to US legislation, respectively.     

Preparation of long-afterglow colloidal solution of Sr2MgSi2O7: Eu, Dy by laser ablation in liquid

We have successfully prepared a novel nanoparticle solution of Sr₂MgSi₂O₇: Eu²⁺, Dy³⁺ with afterglow properties by means of laser ablation in liquid. This process also produced by-products of different kinds, depending on the liquid used. The amount of by-product and the size of the nanoparticles were controlled by the energy density of laser ablation. The amount of by-product was reduced by a decrease in the energy density, which also decreased the particle size of the nanoparticles. The PL spectrum of the nanoparticles was the same as that of the target materials used for laser ablation. The afterglow properties deteriorated with a decrease in particle size. We concluded that an increase in specific surface area caused by a decrease in particle size resulted in the decrease of luminescent intensity.