Preparation and study on radar-absorbing materials of cupric oxide-nanowire-covered carbon fibers

This paper firstly reports that cupric oxide nanowires (CNWs) were synthesized by thermal oxidation of copper coated carbon fibers (Cu/CFs). The results of transmission electron microscope images indicate that the nanowires are about 50 nm in diameter and several microns in length. The optimum growth conditions of the nanowires are found when the film of Cu/CFs is annealed at 400 °C for 4 h in air. The results show that the reflectivity of cupric oxide-nanowire-covered carbon fibers (1-1.3 mm in thickness) is less than −4 dB over the range of 8.6-18 GHz. Furthermore, the possible growth mechanism of CNWs is discussed.     

Synthesis, characterization and electromagnetic properties of Fe1−xCox alloy flower-like microparticles

Fe_1−xCo_x alloy microparticles with size 3-5 μm and novel flower-like shapes were prepared by a simple low temperature reduction method. The electromagnetic properties for the paraffin matrix composites containing Fe_1−xCo_x alloy microparticles were measured using a vector network analyzer in the 2-18 GHz frequency range. As a consequence of large surface- and shape-anisotropy energy for the flower-like shaped 3D microstructures, the strong natural resonance around 8-12 GHz and remarkable dielectric relaxation were observed in the complex permittivity and permeability spectrum, which are dominant in the enhanced electromagnetic wave absorption (EMA) performance. It was found that both the electromagnetic parameters of complex permittivity and permeability and the intensity and location of absorption band were remarkably dependent on the Co/Fe molar ratio. The enhanced EMA performance was obtained in these Fe_1−xCo_x-paraffin (x=0.4, 0.5, and 0.6) composites system. For the Fe_0.5Co_0.5 alloy, the reflection loss (RL) exceeding −20 dB was obtained in the broad frequency range of 5.4-18 GHz with a thin sample thickness of between 1.0 and 2.9 mm. In particular, an optimal RL of −59 dB was obtained at 3.61 GHz with a thin thickness of 3.6 mm for the Fe_0.4Co_0.6 sample. The Fe_1−xCo_x alloy microparticles may be attractive candidates for applications of microwave absorption materials with a wide frequency range and strong absorption in the high frequency region.     

Structural and magnetic properties of sol-gel Co2xNi0.5−x Zn0.5−xFe2O4 thin films

Nanocrystalline Co_2xNi_0.5−xZn_0.5−xFe₂O₄ (x=0−0.5) thin films have been synthesized with various grain sizes by a sol-gel method on polycrystalline silicon substrates. The morphology as well as magnetic and microwave absorption properties of the films calcined at 1073 K were studied using X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, and vibrating sample magnetometry. All films were uniform without microcracks. The Co content in the Co-Ni-Zn films resulted in a grain size ranging from 15 to 32 nm while it ranged from 33 to 49 nm in the corresponding powders. Saturation and remnant magnetization increased with increase in grain size, while coercivity demonstrated a drop due to multidomain behavior of crystallites for a given value of x. Saturation magnetization increased and remnant magnetization had a maximum as a function of grain size independent of x. In turn, coercivity increased with x independent of grain size. Complex permittivity of the Co-Ni-Zn ferrite films was measured in the frequency range 2-15 GHz. The highest hysteretic heating rate in the temperature range 315-355 K was observed in CoFe₂O₄. The maximum absorption band shifted from 13 to 11 GHz as cobalt content increased from x=0.1 to 0.2.     

Electromagnetic properties of manganese-zinc ferrite with lithium substitution

Polycrystalline manganese-zinc ferrite with lithium substitution of composition Li_0.5xMn_0.4Zn_0.6−xFe_2+0.5xO₄ (0.0≤x≤0.4) was prepared by the usual ceramic method. X-ray diffraction analysis confirmed that the samples have a spinel structure and are of single phase for some values of Li content. Lithium doping considerably modifies saturation magnetization since its value increases from 57.5 emu/g for x=0.0 to 82.9 emu/g for x=0.4. Lithium inclusion increases the real permeability (over 1 MHz) while the natural resonance frequency shifts to lower values as the fraction of Li increases. These ferrites show good electromagnetic properties as absorbers in the microwave range of 1 MHz - 1 GHz.     

Raman scattering and room temperature ferromagnetism in Co-doped SrTiO3 particles

Raman scattering has been used to study the influence of cobalt, an effective dopant to obtain SrTiO₃ magnetic oxide, on the lattice dynamics of SrTiO₃. It is found that Co doping increases the lattice defects and induces a Raman vibration mode of 690 cm⁻¹. On the other hand, the ferromagnetism dependence on the x and annealing temperature was clearly and coherently observed in SrTi_1−xCo_xO₃ (x = 0, 0.01, 0.03 and 0.05) nanoparticles. It is found that the ferromagnetism of SrTi_1−xCo_xO₃ nanoparticles is weakly related to crystal deformation and oxygen vacancies in SrTiO₃. So, F-center model can explain the origin of the ferromagnetism in the prepared Co-doped SrTiO₃ samples. At the same time, the finding of large room-temperature ferromagnetism (1.6 emu/g) in this system would stimulate further interest in the area of more complicated ternary oxides.     

Magnetic properties of nanocrystalline Co1−xZnxFe2O4 prepared by forced hydrolysis method

Nanocrystalline zinc-substituted cobalt ferrite powders, Co_1−xZn_xFe₂O₄ (x=0, 0.2, 0.4), were for the first time prepared by forced hydrolysis method. Magnetic and structural properties in these specimens were investigated. The average crystallite size is about 3.0 nm. When the zinc substitution increases from x=0 to x=0.4, at 4.2 K, the saturation magnetization increases from 72.1 to 99.7 emu/g and the coercive field decreases from 1.22 to 0.71 T. All samples are superparamagnetic at room temperature and ferrimagnetic at temperatures below the blocking temperature. The high value of the saturation magnetization and the very thin thickness of the disorder surface layer of all samples suggests that this forced hydrolysis method is suitable not only for preparing two metal element systems but also for three or more ones.     

Structural and magnetic properties of Mg(In2−xMnx)O4 system

We synthesized the Mn-doped Mg(In_2−xMn_x)O₄ oxides with 0.03?x?0.55 using a solid-state reaction method. The X-ray diffraction patterns of the samples were in a good agreement with that of a distorted orthorhombic spinel phase. Their lattice parameters and unit-cell volumes decrease with x due to the substitution of the smaller Mn³⁺ ions to the larger In³⁺ ions. The undoped MgIn₂O₄ oxide presents diamagnetic signals for 5 K?T?300 K. The M(H) at T=300 K reveals a fairly negative-sloped linear relationship. Neither magnetic hysteresis nor saturation behavior was observed in this parent sample. For the Mn-doped samples, however, positive magnetization were observed between 5 and 300 K even if the x value is as low as 0.03. The mass susceptibility enhances with Mn content and it reaches the highest value of 1.4×10⁻³ emu/g Oe (at T=300 K) at x=0.45. Furthermore, the Mn-doped oxides with x=0.06 and 0.2, respectively, exhibit nonlinear magnetization curves and small hysteretic loops in low magnetic fields. Susceptibilities of the Mn-doped samples are much higher than those of MnO₂, Mn₂O₃ oxides, and Mn metals. These results show that the oxides have potential to be magnetic semiconductors.     

Synthesis and characterization of Sr(ZnZr)x Fe12−2xO19-PANI composites

Strontium zinc zirconium hexaferrites/polyaniline (Sr(ZnZr)_xFe_12−2xO₁₉-PANI, x=0, 0.5, 1.0) composites were synthesized by oxidative chemical polymerization of aniline in the presence of ammonium peroxydisulfate (APS). The structure and morphology of the product was characterized by FTIR, TGA and SEM. The particle size of the core material was found to be about 250-500 nm. After coating with polyaniline, the particle size of Sr(ZnZr)_0.5Fe₁₁O₁₉-PANI composites grew upto 0.5-1.0 μm. XRD of the ferrites indicated that the structure of the core materials is hexagonal, with lattice constants around 5.886-5.885 Å. It was found that the saturation magnetization (M_S) and coercivity (H_C) for Sr(ZnZr)_xFe_12−2xO₁₉-PANI composites decreased after polyaniline coating. The composite under applied magnetic field, exhibited ferromagnetic hysteretic loops with high saturation magnetization (M_S=18.9-3.8 emu/g) and coercivity (H_C=3850.0-583.91 Oe).     

Absorbing properties and structural design of microwave absorbers based on W-type La-doped ferrite and carbon fiber composites

Sol–gel method was used to prepare W-type BaCo₂Fe₁₆O₂₇ hexaferrite and La-doped Ba_0.7La_0.3Co₂Fe₁₆O₂₇ hexaferrite. Electromagnetic parameters of the ferrites and short carbon fiber composites were measured, and reflectivity was calculated according to transmission-line theory in the range 12.4–18 GHz. The results show that reflection loss of the doped ferrite composite is higher as compared to the no doped ferrite composite. Based on the above calculation, double-layer absorbers containing La-doped ferrite and carbon fiber composites were designed, and reflectivity of the double-layer absorbers made of different thickness and composition was calculated. Finally, a kind of structural absorber having excellent absorbing properties was achieved, and the bandwidth of the reflection loss less than −10 dB can reach 5.2 GHz in the range of 12.4–18 GHz.     

Ferromagnetism in amorphous Ge1−xMnx grown by low temperature vapor deposition

Magnetic properties of amorphous Ge_1−xMn_x thin films were investigated. The thin films were grown at 373 K on (100) Si wafers by using a thermal evaporator. Growth rate was ∼35 nm/min and average film thickness was around 500 nm. The electrical resistivities of Ge_1−xMn_x thin films are 5.0×10⁻⁴∼100 Ω cm at room temperature and decrease with increasing Mn concentration. Low temperature magnetization characteristics and magnetic hysteresis loops measured at various temperatures show that the amorphous Ge_1−xMn_x thin films are ferromagnetic but the ferromagnetic magnetizations are changing gradually into paramagnetic as increasing temperature. Curie temperature and saturation magnetization vary with Mn concentration. Curie temperature of the deposited films is 80-160 K, and saturation magnetization is 35-100 emu/cc at 5 K. Hall effect measurement at room temperature shows the amorphous Ge_1−xMn_x thin films have p-type carrier and hole densities are in the range from 7×10¹⁷ to 2×10²² cm⁻³.     

The electrochemical preparation and microwave absorption properties of magnetic carbon fibers coated with Fe3O4 films

Electrodeposition was employed to fabricate magnetite (Fe₃O₄) coated carbon fibers (MCCFs). Temperature and fiber surface pretreatment had a significant influence on the composition and morphology of Fe₃O₄ films. Uniform and compact Fe₃O₄ films were fabricated at 75 °C on both nitric acid treated and untreated carbon fibers, while the films prepared at 60 °C were continuous and rough. Microwave measurements of MCCF/paraffin composites (50 wt.% of MCCFs, pretreated carbon fibers as deposition substrates) were carried out in the 2-18 GHz frequency range. MCCFs prepared at 60 °C obtained a much higher loss factor than that prepared at 75 °C. However, the calculation results of reflection loss were very abnormal that MCCFs prepared at 60 °C almost had no absorption property. While MCCFs prepared at 75 °C exhibited a good absorption property and obtained −10 dB and −20 dB refection loss in wide matching thickness ranges (1.0-6.0 mm and 1.7-6.0 mm range, respectively). A secondary attenuation peak could also be observed when the thickness of MCCF/paraffin composite exceeded 4.0 mm. The minimum reflection loss was lower.     

Preparation and magnetic properties of the conductive Co(1−x)NixFe2O4/polyaniline microsphere composites

Core-shell Co_(1−x)Ni_xFe₂O₄/polyaniline nanoparticles, where the core was Co_(1−x)Ni_xFe₂O₄ and the shell was polyaniline, were prepared by the combination of sol-gel process and in-situ polymerization methods. Nanoparticles were investigated by Fourier transform spectrometer, X-ray diffraction diffractometer, Scanning electron microscope, Differential thermal analysis and Superconductor quantum interference device. The results showed that the saturation magnetization of pure Co_(1−x)Ni_xFe₂O₄ nanoparticles were 57.57 emu/g, but Co_(1−x)Ni_xFe₂O₄/polyaniline composites were 37.36 emu/g. It was attributed to the lower content (15 wt%), smaller size and their uneven distribution of Co_(1−x)Ni_xFe₂O₄ nanoparticles in the final microsphere composites. Both Co_(1−x)Ni_xFe₂O₄ and PANI/Co_(1−x)Ni_xFe₂O₄ showed superparamagnetism.     

Hydrothermal-induced oriented growth of Fe–Co alloy and Sm-substituted magnetite nanowire composites

Fe–Co alloy and Sm³⁺-substituted magnetite nanowire composites (Co_xFe_1−x/Co_yFe_1−ySm_zFe_2−zO₄) have been synthesized via a hydrothermal method without using surfactants or templates. The effects of substitution on structure and morphology were investigated by powder X-ray diffraction, X-ray photoelectron spectroscopy, Mössbauer spectroscopy, and transmission electron microscopy (TEM). The TEM image shows that the average diameter of the magnetite nanowires is about 40 nm and the length is several micrometers. The z=0.1 composite shows relatively high saturation magnetization (92.3 emu/g) detected by a vibrating sample magnetometer. The possible growth mechanism of the nanowires is discussed on the basis of the crystal structure of the materials. From the perspective of thermodynamics, we explain the postulated mechanism of the hydrothermal reaction.     

Adjustable microwave absorption properties of flake shaped (Ni0.5Zn0.5)Fe2O4/Co nanocomposites with stress induced orientation

Flake shaped (Ni_0.5Zn_0.5)Fe₂O₄/Co nanocomposites were successfully fabricated by co-precipitating of Ni-Zn ferrite on the surface of cobalt nanoflakes. The electromagnetic characteristics of the samples were studied at the frequency of 0.1–14 GHz. The results showed that the cobalt nanoflakes in compacted nanocomposites were well orientated, and the nanocomposites were characterized with low optimal reflection loss (RL) of −33.8 dB at 11.5 GHz and broad RL bandwidth for <−20 dB in the frequency range of 7.6–12.1 GHz. At the same time, the position of the absorptive band can be adjusted by changing the mass ratio of ferrite to cobalt in the nanocomposites. It is proposed that the excellent microwave absorption properties are related to the combination of strong shape anisotropy of cobalt nanoflakes and adjustable dielectric loss.     

Effect of Co or Mn addition on the soft magnetic properties of amorphous Fe89−xZr11Bx (x=5, 10) alloy ribbons

The temperature and field dependent magnetic properties of melt-spun amorphous Fe_89−x−yZr₁₁B_x(Co,Mn)_y (x=5, 10 and 0≤y≤10) alloys in the temperature range 5-1200 K are reported. The Curie temperature and saturation magnetization at room temperature increase (decrease) almost linearly with Co (Mn) addition. With increasing Co concentration, the room temperature coercivity increases at the rate of 2.26 (0.28) A/m per at% for the x=5 (10) samples. The high-field magnetic susceptibility and local magnetic anisotropy decrease (increases) rapidly with increasing Co (Mn) concentration. The thermomagnetic curves show a marked increase in magnetization above 850 K corresponding to the crystallization of α-FeCo (α-Fe) phase in samples containing Co (Mn). The Curie temperature of the crystalline phase increases (remains same) with increasing Co (Mn) concentration with the formation of α-FeCo (α-Fe). Addition of Co up to 10 at% in Fe-Zr-B improves the room temperature saturation magnetization from 0.56 to 1.2 T, and Curie temperature from 315 to 476 K. Also, the coercivity increases with Co addition from 1.27 to 23.88 A/m for x=5 and from 7.64 to 10.35 A/m for x=10 alloy. The non-collinear spin structures that characterize Fe rich Fe-Zr-B amorphous alloys have been used to describe the observed results.     

Magnetic and Microwave Absorbing Properties of Electrospun Ba(1−x)LaxFe12O19 Nanofibers

Ba_(1−x)La_xFe₁₂O₁₉ (0.00≤x≤0.10) nanofibers were fabricated via the electrospinning technique followed by heat treatment at different temperatures for 2 h. Various characterization methods including scanning electron microscopy (SEM), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and microwave vector network analyzer were employed to investigate the morphologies, crystalline phases, magnetic properties, and complex electromagnetic parameters of nanofibers. The SEM images indicate that samples with various values of x are of a continuous fiber-like morphology with an average diameter of 110±20 nm. The XRD patterns show that the main phase is M-type barium hexaferrite without other impurity phases when calcined at 1100 °C. The VSM results show that coercive force (H_c) decreases first and then increases, while saturation magnetization (M_s) reveals an increase at first and then decreases with La³⁺ ions content increase. Both the magnetic and dielectric losses are significantly enhanced by partial substitution of La³⁺ for Ba²⁺ in the M-type barium hexaferrites. The microwave absorption performance of Ba_0.95La_0.05Fe₁₂O₁₉ nanofibers gets significant improvement: The bandwidth below −10 dB expands from 0 GHz to 12.6 GHz, and the peak value of reflection loss decreases from −9.65 dB to −23.02 dB with the layer thickness of 2.0 mm.     

Monodispersed nanocrystalline Co1–xZnxFe2O4 particles by forced hydrolysis: Synthesis and characterization

Zinc-substituted cobalt ferrites, Co_1–xZn_xFe₂O₄, were for the first time successfully prepared by forced hydrolysis method. The obtained materials are single phase, monodispersed nanocrystalline with an average grain size of about 3 nm. These materials are superparamagnetic at room temperature and ferrimagnetic at temperature lower than the blocking temperature. When the zinc substitution increases from x=0 to 0.4, at 4.2 K, the saturation magnetization increases from 72.1 to 99.7 emu/g. The high saturation magnetization of these samples suggests that this method is suitable for preparing high-quality nanocrystalline magnetic ferrites for practical applications.     

Structure and RT ferromagnetism of Fe-doped AlN films

Al_1−xFe_xN_1−δ thin films with 0 ≤ x ≤ 13.6% were deposited by dc magnetron co-sputtering at room temperature (RT). It is found that Fe atom will substitutes the Al atom in the lattice when x ≤ 1.2%, while it will embed into the interstice of the lattice at larger Fe content. RT ferromagnetism was observed in all doped samples. A maximum saturated magnetization 2.81 emu/cm³ of the film is found to be induced by AlFeN ternary alloy when x = 1.2%.     

Preference orientation and magnetic properties of CoxFe3−xO4 nanocrystalline thin films on quartz substrate

Nanocrystalline spinel ferrite thin films of Co_xFe_3−xO₄ (x=0.3$x=0.3$, 0.5, 0.8, and 1.0) have been prepared by RF sputtering on quartz substrate without a buffer layer at room temperature and annealed at the temperature range from 200 to 600 °C in air. The as-sputtered films exhibit the preferred orientation and the high magnetization and coercivity. After annealing, the preferred orientations become poor, but the magnetization and coercivity increase. The sample with a magnetization of 455 emu/cm³, a coercivity of 2.8 kOe, a remanence ratio of 0.72, and a maximum energy product of 2.4 MGOe has been obtained. The influence of Co ions and annealing temperature on the magnetic properties has been discussed.     

Reflectivity measurements of superionic conductors for Li ion secondary battery materials

The reflection measurements of superionic conductors LiCoO₂ and Li_1-xCoO₂, which are already in use for the positive electrode material of 4 V rechargeable lithium batteries, have been performed in the millimeter wave region from 6 to 60 cm⁻¹ using the electron storage ring facilities of Institute of Molecular Science in Okazaki. The increase of the reflectivity has been observed in the low wavenumber region below 10 cm^-1 above 300 K in Li_1-xCoO₂ for the first time, while the reflectivity of LiCoO₂ has almost the constant value in all observed temperature region between 77 to 380 K. The results will be discussed in connection with our previous results of LiNiO₂.