Cu2ZnSnSe4 thin films prepared by selenization of co-electroplated Cu-Zn-Sn precursors

A novel technique for growth of high quality Cu₂ZnSnSe₄ (CZTSe) thin films is reported in our work. The CZTSe thin films were fabricated onto Mo layers by co-electroplating Cu-Zn-Sn precursors followed by annealing in the selenium vapors at the substrate temperature of 550 °C. The morphology and structure of CZTSe thin films were characterized using scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffraction (XRD) and Raman scattering spectrum, respectively. The results revealed that the single phase was in the CZTSe thin films, and the other impurities such as ZnSe and Cu₂SnSe₃ were not existed though they were difficult to distinguish both from EDS and XRD.     

Preparing Cu2ZnSnS4 films using the co-electro-deposition method with ionic liquids

Cu2ZnSnS4（CZTS） films are successfully prepared by co-electrodeposition in aqueous ionic solution and sulfurized in elemental sulfur vapor ambient at 400 C for 30 min using nitrogen as the protective gas.It is found that the CZTS film synthesized at Cu/（Zn＋Sn）=0.71 has a kesterite structure,a bandgap of about 1.51 eV,and an absorption coefficient of the order of 10 4 cm 1.This indicates that the co-electrodeposition method with aqueous ionic solution is a viable process for the growth of CZTS films for application in photovoltaic devices.     

Structural and optical properties of Er, Yb co-doped Y2O3 thin films

Thin Er³⁺, Yb³⁺ co-doped Y₂O₃ films were grown on (1 0 0) YAG substrates by pulsed laser deposition. Ceramic targets having different active ion concentration were used for ablation. The influence of the rare-earth content and oxygen pressure applied during the deposition on the structural, morphological and optical properties of the films were investigated. The films deposited at the lower pressure, 1 Pa, and at 1/10 Er to Yb doping ratio are highly textured along the (1 1 1) direction of the Y₂O₃ cubic phase. In addition to the crystalline structure, these films possess smoother surface compared to those prepared at the higher pressure, 10 Pa. All other films are polycrystalline, consisting of cubic and monoclinic phases of Y₂O₃. The rougher surface of the films produced at the higher-pressure leads to higher scattering losses and different behavior of the reflectivity spectra. Optical anisotropy in the films of less than 0.004 was measured regardless of the monoclinic structure obtained. Waveguide losses of about 1 dB/cm at 633 nm were obtained for the films produced at the lower oxygen pressure.     

Temperature induced band gap shrinkage in Cu2GeSe3: Role of electron-phonon interaction

The ternary semiconducting compound Cu₂GeSe₃ has been investigated for optical properties with photoacoustic spectroscopy. Optical absorption spectra of Cu₂GeSe₃ is obtained in the range of 0.76-0.81 eV photon-energy at temperatures between 80 and 300 K. The thermal variation of band gap energy has been examined from the optical absorption spectra at different temperatures. The temperature induced band gap shrinkage has been explained on the basis of electron-phonon interaction. Varshni's empirical relation in conjunction with Vina and Passler model is taken into consideration for data fitting. The Debye temperature was calculated approximately as 240 K. The acoustic phonons with a characteristic temperature as 160 K corresponding to effective mean frequency have been attributed to the thermal variation of the energy gap.     

Characterization of electrodeposited Bi2S3 thin films by holographic interferometry

Optical non destructive evaluation methods, using lasers as the object illumination source, include holographic interferometry. It is widely used to measure stress, strain, and vibration in engineering structures. Double exposure holographic interferometry (DEHI) technique is used to determine thickness and stress of electrodeposited bismuth trisulphide (Bi₂S₃) thin films for various deposition times. The same is tested for other concentration of the precursors. It is observed that, increase in deposition time, increases thickness of thin film but decreases stress to the substrate. The structural, optical and surface wettability properties of the as deposited films have been studied using X-ray diffraction (XRD), optical absorption and contact angle measurement, respectively. The X-ray diffraction study reveals that the films are polycrystalline with orthorhombic crystal structure. Optical absorption study shows the presence of direct transition with band bap 1.78 eV. The water contact angle measurement shows hydrophobic nature of Bi₂S₃ thin film surface.     

Substrate effects on V2O3 thin films

We apply density functional theory and the augmented spherical wave method to analyze the electronic structure of V₂O₃ in the vicinity of an interface to Al₂O₃. The interface is modeled by a heterostructure setup of alternating vanadate and aluminate slabs. We focus on the possible modifications of the V₂O₃ electronic states in this geometry, induced by the presence of the aluminate layers. In particular, we find that the tendency of the V 3d states to localize is enhanced and may even cause a metal-insulator transition.     

Studies on electrodeposited As2S3 thin films by double exposure holographic interferometry technique

Arsenic trisulphide (As₂S₃) thin films have been deposited onto stainless steel and fluorine doped tin oxide (FTO) coated glass substrates by electrodeposition technique using arsenic trioxide (As₂O₃) and sodium thiosulphate (Na₂S₂O₃) as precursors and ethylene diamine tetracetic acid (EDTA) as a complexing agent. Double exposure holographic interferometry (DEHI) technique was used to determine the thickness and stress of As₂S₃ thin films. It was observed that the thickness of the thin film increases whereas film stress to the substrate decreases with an increase in the deposition time. X-ray diffraction and water contact angle measurements showed polycrystalline and hydrophilic surface respectively. The bandgap energy increases from 1.82 to 2.45 eV with decrease in the film thickness from 2.2148 to 0.9492 μm.     

The microwave response of MgB2 /Al2O3 superconducting thin films

Microwave characteristics of MgB2/Al2O3 superconducting thin films were investigated by coplanar resonator technique. The thin films studied have different grain sizes resulting from different growth techniques. The experimental results can be described very well by a grain-size model which combines coplanar resonator theory and Josephson junction network model. It was found that the penetration depth and surface resistance of thin films with smaller grain sizes are larger than those of thin films with larger grain sizes.     

Optimization of annealing conditions of In2S3 thin films deposited by vacuum thermal evaporation

In₂S₃ thin films were grown on glass substrates by means of the vacuum thermal evaporation technique and subsequently thermally annealed in nitrogen and free air atmosphere from 250 to 350 °C for different durations. Experimental parameters have been adjusted in order to optimize the annealing conditions, and to obtain high band gap energy at low deposition temperature, as required for photovoltaic applications. In order to improve our understanding of the influence of the deposition and annealing parameters on device performance, we have investigated our indium sulfide material by X-ray diffraction, energy dispersive X-ray analysis (EDAX), atomic force microscopy (AFM) and spectrophotometry. The optical and structural properties of the films were studied as a function of the annealing temperature and durations. X-ray diffraction analysis shows the initial amorphous nature of deposited In-S thin films and the phase transition into crystalline In₂S₃ upon thermal annealing. Films show a good homogeneity and optical direct band gap energy about 2.2 eV. An annealing temperature of 350 °C during 60 min in air atmosphere were the optimal conditions.     

Optical and electrical properties of Y2O3 thin films prepared by ion beam assisted deposition

Y₂O₃ thin films were deposited by ion beam assisted deposition (IBAD) and the effects of fabrication parameters such as substrate temperature and ion energy on the structure, optical and electrical properties of the films were investigated. The results show that the deposited Y₂O₃ films had less optical absorption, larger refractive index, and better film crystallinity with the increase of substrate temperature or ion energy. The as-deposited Y₂O₃ films without ion-beam bombardment had larger relative dielectric constant (?_r) and the ?_r decreased with time even over by 40%, while the ?_r of films prepared with high ion energy had less changes, only less than 3%. Also, with the increase of ion energy, the electrical breakdown strength and the figure of merit increased.     

CuInS2 thin films obtained through the annealing of chemically deposited In2S3-CuS thin films

In this work, we report the formation of CuInS₂ thin films on glass substrates by heating chemically deposited multilayers of copper sulfide (CuS) and indium sulfide (In₂S₃) at 300 and 350 °C in nitrogen atmosphere at 10 Torr. CIS thin films were prepared by varying the CuS layer thickness in the multilayers with indium sulfide. The XRD analysis showed that the crystallographic structure of the CuInS₂ (JCPDS 27-0159) is present on the deposited films. From the optical analysis it was estimated the band gap value for the CIS film (1.49 eV). The electrical conductivity varies from 3 × 10⁻⁸ to 3 Ω⁻¹ cm⁻¹ depending on the thickness of the CuS film. CIS films showed p-type conductivity.     

Photoluminescence study of disordering in the cation sublattice of Cu2ZnSnS4

In this study we investigated the influence of the degree of disordering in the cation sublattice on low temperature photoluminescence (PL) properties of Cu₂ZnSnS₄ (CZTS) polycrystals. The degree of disordering was changed by using different cooling rates after post-annealing at elevated temperatures. The results suggest that in the case of higher degree of cation sublattice disorder radiative recombination involving defect clusters dominates at T = 10 K. These defect clusters induce local band gap energy decrease in CZTS. The concentration of defect clusters can be reduced by giving more time for establishing ordering in the crystal lattice. As a result, radiative recombination mechanism changes and band-to-impurity recombination involving deep acceptor defect with ionization energy of about 200 meV starts to dominate in the low temperature PL spectra of CZTS polycrystals.     

Electronic and optical properties of kesterite Cu2ZnSnS4 under in-plane biaxial strains: First-principles calculations

The electronic structures and optical properties of Cu₂ZnSnS₄ (CZTS) under in-plane biaxial strain were systematically investigated using first-principles calculations based on generalized gradient approximation and hybrid functional method, respectively. It is found that the fundamental bandgap at the Γ point decreases linearly with increasing tensile biaxial strain perpendicular to c-axis. However, a bandgap maximum occurs as the compressive biaxial strain is 1.5%. Further increase of compressive strain decreases the bandgap. In addition, the optical properties of CZTS under biaxial strain are also calculated, and the variation trend of optical bandgap with biaxial strain is consistent with the fundamental bandgap.     

Photoluminescence characterization of polycrystalline n-type Cu2O films

Electrodeposition was used to deposit Cu₂O thin films on ITO substrates. Photoresponse of the film clearly indicated n-type behavior of Cu₂O in photoelectrochemical cells. The temperature dependence of photoluminescence (PL) revealed that the spectra consist of donor-acceptor pair emissions and the recombination between electrons bound to donors and free holes. We observed that the dominant intrinsic defect, oxygen vacancies, creates a donor energy level at 0.38 eV below the bottom of the conduction band. As a result, this donor level acts as a center for both PL emissions and to produce n-type conductivity in the electrodeposited Cu₂O films. In addition, an acceptor energy level at 0.16 eV from the top of the valence band was observed.     

SrBi2Ta2O9/Bi4Ti3O12复合铁电薄膜的制备与特性研究

采用溶胶凝胶工艺在p-Si衬底上制备了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合铁电薄膜. 研究了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合薄膜的微观结构与生长行为、铁电性能和疲劳特性. 研究表明: Si衬底Bi₄Ti< 关键词： 2Ta₂O₉')" href="#">SrBi₂Ta₂O₉ 4Ti₃O₁₂')" href="#">Bi₄Ti₃O₁₂ 复合铁电薄膜 溶胶凝胶工艺     

Structural, electrical and optical properties of TiO2 doped WO3 thin films

TiO₂ doped WO₃ thin films were deposited onto glass substrates and fluorine doped tin oxide (FTO) coated conducting glass substrates, maintained at 500 °C by pyrolytic decomposition of adequate precursor solution. Equimolar ammonium tungstate ((NH₄)₂WO₄) and titanyl acetyl acetonate (TiAcAc) solutions were mixed together at pH 9 in volume proportions and used as a precursor solution for the deposition of TiO₂ doped WO₃ thin films. Doping concentrations were varied between 4 and 38%. The effect of TiO₂ doping concentration on structural, electrical and optical properties of TiO₂ doped WO₃ thin films were studied. Values of room temperature electrical resistivity, thermoelectric power and band gap energy (E_g) were estimated. The films with 38% TiO₂ doping in WO₃ exhibited lowest resistivity, n-type electrical conductivity and improved electrochromic performance among all the samples. The values of thermoelectric power (TEP) were in the range of 23-56 μV/K and the direct band gap energy varied between 2.72 and 2.86 eV.     

Influence of postdeposition annealing on structural properties and electrical characteristics of thin Tm2O3 and Tm2Ti2O7 dielectrics

We describe the structural properties and electrical characteristics of thin thulium oxide (Tm₂O₃) and thulium titanium oxide (Tm₂Ti₂O₇) as gate dielectrics deposited on silicon substrates through reactive sputtering. The structural and morphological features of these films were explored by X-ray diffraction, X-ray photoelectron spectroscopy, secondary ion mass spectrometry, and atomic force microscopy, measurements. It is found that the Tm₂Ti₂O₇ film annealed at 800 °C exhibited a thinner capacitance equivalent thickness of 19.8 Å, a lower interface trap density of 8.37 × 10¹¹ eV⁻¹ cm⁻², and a smaller hysteresis voltage of ∼4 mV than the other conditions. We attribute this behavior to the Ti incorporated into the Tm₂O₃ film improving the interfacial layer and the surface roughness. This film also shows negligible degrees of charge trapping at high electric field stress.     

Anodization of aluminium thin films on pSi and annihilation of strong luminescence from Al2O3

Photoluminescence (PL) of Al₂O₃ films obtained by anodization of thermally evaporated and annealed thin Al films on p⁺⁺Si in 0.3 M oxalic acid has been investigated. Thermal annealing at 200–950 °C under the dry nitrogen atmosphere was used for deactivation of luminescence centres. Luminescence from as grown films was broad and located at 425 nm. This luminescence reached to highest level after annealing at 600 °C. Maximum 10 min was required for full optical activation and prolonged annealing up to 4 h did not change the luminescence intensity. Because of deep levels, absorption band edge of as grown films was shifted to the lower energy which is 3.25 eV. Annealing above 800 °C reduced the PL intensity and this observation was correlated with the blue shift of band edge as the defects annealed out. Disappearing PL intensity and blue shift of band edge absorption after annealing at 950 °C was mainly attributed to the oxygen-related defects and partly to impurities that may be originated from oxalic acid. AFM results did not show any hexagonally ordered holes but uniformly distributed nanosized Al₂O₃ clusters that were clearly seen. XRD measurements on as grown Al₂O₃ showed only [1 1 0] direction of α phase. Debye–Scherer calculation for this line indicates that cluster size is 35.7 nm. XRD and AFM pictures suggest that nanocrystalline Al₂O₃ are embedded in amorphous Al₂O₃.     

Dry etching of CuCrO2 thin films

Highly conducting films of p-type CuCrO₂ are attractive as hole-injectors in oxide-based light emitters. In this paper, we report on the development of dry etch patterning of CuCrO₂ thin films. The only plasma chemistry that provided some chemical enhancement was Cl₂/Ar under inductively coupled plasma conditions. Etch rates of ∼500 Å min⁻¹ were obtained at chuck voltages around −300 V and moderate source powers. In all cases, the etched surface morphologies were improved relative to un-etched control samples due to the smoothing effect of the physical component of the etching. The threshold ion energy for the onset of etching was determined to be 34 eV. Very low concentrations (≤1 at.%) of residual chlorine were detected on the etched surfaces but could be removed by simple water rinsing.     

Synthesis and characterization of Cu2ZnSnSe4 nanotube arrays on fluorine-doped tin oxide glass substrates

Highly ordered arrays of Cu₂ZnSnSe₄ nanotubes have been successfully synthesized on fluorine-doped tin oxide glass substrate using ZnO nanorod arrays as sacrificial templates. The structure, morphology and optical properties of the Cu₂ZnSnSe₄ arrays were characterized by X-ray diffraction, Raman spectrometry, field-emission scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray, and UV–Vis absorption spectroscopy. The diameter and length of the Cu₂ZnSnSe₄ nanotubes can be adjusted by tuning the diameter and length of the ZnO nanorods. In addition, the effect of the length on the performance of the photoelectrochemical cells was also investigated.