Bismuth determination in environmental samples by hydride generation-electrothermal atomic absorption spectrometry

A hydride generation procedure, via flow injection, coupled to electrothermal atomic absorption spectrometry was optimised for Bi determination in sea water and hot-spring water and acid extracts from coal, coal fly ash and slag samples. The effects of several variables such as hydrochloric acid and sodium tetrahydroborate concentrations, hydrochloric acid and sodium tetrahydroborate flow rates, reaction coil length, trapping and atomisation temperatures, trapping time and the Ar flow rate have been investigated by using a 2⁹*3/128 Plackett-Burman design. From these studies, certain variables (sodium tetrahydroborate concentration and trapping time) showed up as significant, and they were optimised by a 2²+star central composite design. In addition, a study of the bismuthine trapping and atomisation efficiency from graphite tubes (GTs) permanently treated with uranium, tantalum, lanthanum oxide, niobium, beryllium oxide, chromium oxide and tantalum carbide were investigated. The results obtained were compared with those achieved by iridium and zirconium-treated GTs. The best analytical performances, with characteristic mass of 35 pg and detection limit of 70 ng l⁻¹, were achieved by using U-treated GTs. Accuracy were checked using several reference materials: 1643d (Trace Elements in Water), TM-24 (Reference Water), GBW-07401 (Soil) and 1632c (Trace Elements in Coal).     

Cadmium determination in biological samples by direct solid sampling flame atomic absorption spectrometry

A direct solid sampling flame atomic absorption spectrometric procedure for trace determination of cadmium in biological samples has been developed. Test samples (0.05–2.00 mg) were ground and weighed into small polyethylene vials, which were connected to the device for solid sample introduction into a conventional air/acetylene flame. Test samples were carried as a dry aerosol to a quartz cell, placed between the burner and the optical path, which had a perpendicular entrance and a slit in the upper part. The atomic vapor generated in the flame produced a transient signal that was totally integrated within 1 s. The effect of operating conditions and the extent of grinding on the analytical signal were evaluated. Background signals were always low and a characteristic mass of 0.29 ng Cd was obtained. Calibration was performed using different masses of solid certified reference materials. Results obtained for certified and in-house reference materials were typically within the 95% confidence interval of the certified and/or reference value, and the precision, expressed as relative standard deviation, was between 3.8 and 6.7%. The proposed system is simple and it might be adapted to conventional atomic absorption spectrometers allowing the determination of Cd in more than 80 test samples per hour, excluding weighing.     

Determination of As,Bi, Sb and Sn in conifer needles from various locations in Poland and Norway by hydride generation inductively coupled plasma atomic emission spectrometry

Hydride generation inductively coupled plasma atomic emission spectrometry (HG-ICP-AES) in the system with aerosolised sample introduction has been employed for the first time for analysis of conifer needles. Arsenic, bismuth, antimony and tin along with other trace elements were simultaneously determined in pine, spruce, yew and thuja foliage sampled from various locations in Poland and Norway. Quality of the measurements was assured by examination of two attested plant reference materials. The application of different analyte introduction techniques and interference effects from matrix elements, i.e. Na, K, Mg, Ca and transition metals in the analysis of needles are discussed.     

Determination of As, Sb, Se, Te and Bi in milk by slurry sampling hydride generation atomic fluorescence spectrometry

A simple and fast analytical procedure has been developed for the determination of As, Sb, Se, Te and Bi in milk samples by hydride generation atomic fluorescence spectrometry (HG-AFS). Samples were treated with aqua regia for 10 min in an ultrasound water bath and pre-reduced with KBr for total Se and Te determination or with KI and ascorbic acid for total As and Sb, the determination of Bi being possible in all with or without pre-reduction. Slurries of samples, in the presence of antifoam A, were treated with NaBH₄ in HCl medium to obtain the corresponding hydrides, and AFS measurements were processed in front of external calibrations prepared and measured in the same way as samples. Results obtained by the developed procedure compare well with those found after microwave-assisted complete digestion of samples. The proposed method is simple and fast, and only 1 ml of milk is needed. The values obtained for detection limit are 2.5, 1.6, 3, 6 and 7 ng l⁻¹ for As, Sb, Se, Te and Bi respectively in the diluted samples, with average relative standard deviation values of 3.8, 3.1, 1.9, 6.4 and 1.2% for three independent analysis of a series of commercially available samples of different origin. Data found in Spanish market samples varied from 3.2±0.3 to 11.3±0.2 ng g⁻¹ As, from 3.1±0.2 to 11.6±0.4 ng g⁻¹ Sb, from 10.7±0.5 to 25.5±0.4 ng g⁻¹ Se, from 0.9±0.2 to 9.4±0.6 ng g⁻¹ Te and from 11.5±0.1 to 27.7±0.4 ng g⁻¹ Bi.     

Hydride generation atomic fluorescence spectrometric determination of As, Bi, Sb, Se(IV) and Te(IV) in aqua regia extracts from atmospheric particulate matter using multivariate optimization

A highly sensitive and simple method, based on hydride generation and atomic fluorescence detection, has been developed for the determination of As, Bi, Sb, Se(IV) and Te(IV) in aqua regia extracts from atmospheric particulate matter samples. Atmospheric particulates matter was collected on glass fiber filters using a medium volume sampler (PM1 particulate matter). Two-level factorial designs have been used to optimise the hydride generation atomic fluorescence spectrometry (HG-AFS) procedure. The effects of several parameters affecting the hydride generation efficiency (hydrochloric acid, sodium tetrahydroborate and potassium iodide concentrations and flow rates) have been evaluated using a Plackett-Burman experimental design. In addition, parameters affecting the hydride measurement (delay, analysis and memory times) have been also investigated. The significant parameters obtained (sodium tetrahydroborate concentration, sodium tetrahydroborate flow rate and analysis time for As; hydrochloric acid concentration and sodium tetrahydroborate flow rate for Se(IV); and sodium tetrahydroborate concentration and sodium tetrahydroborate flow rate for Te(IV)) have been optimized by using 2ⁿ + star central composite design. Hydrochloric acid concentration and sodium tetrahydroborate flow rate were the significant parameters obtained for Sb and Bi determination, respectively. Using a univariate approach these parameters were optimized. The accuracy of methods have been verified by using several certified reference materials: SRM 1648 (urban particulate matter) and SRM 1649a (urban dust). Detection limits in the range of 6 × 10⁻³ to 0.2 ng m⁻³ have been achieved. The developed methods were applied to several atmospheric particulate matter samples corresponding to A Coruña city (NW Spain).     

Determination of As,Sb and Bi in high-purity copper by electrothermal atomic absorption spectrometry

As, Sb and Bi were determined in copper electric cables by atomic absorption spectrometry with electrothermal atomization in a graphite furnace. The interferences in the determination of As, Sb and Bi caused by eleven cationic species and six types of acid were studied. The different volatilization of the copper matrix in comparison to the analyte was studied, as a means of increasing the analyte signal/non-specific absorption signal ratio.     

HG-ICP-MS法测定纯镍中痕量As、Sb、Bi、Se、Te、Sn

应用本实验室设计的雾室座作为接口，采用气动型流动注射氢化物发生(HG)装置与电感耦合等离子体质谱仪(ICP-MS)联机。考察了各种介质条件及镍基体对生成氢化物的影响并应用氢氧化镧共沉淀分离富集，HG与ICP-MS联机测定纯镍中易于生成氢化物的As、Sb、Bi、Se、Te、Sn 6个元素，加标回收率为96．5％-102．2％，RSD为2．4％-5．8％，方法检出限为7．1-30ng／L。     

Heavy metal determination in atmospheric particulate matter by Instrumental Neutron Activation Analysis

Instrumental Neutron Activation Analysis (INAA) is employed for its important analytical properties. Fundamentally, INAA is a multi-elemental technique allowing the determination of about 40 elements with a good Limit of Detection. In this paper we applied this nuclear technique to study the element composition in PM10 determining about 30 elements.25 filters were collected in downtown Rome from October 1999 to April 2000 and irradiated at the nuclear reactor Triga Mark II (ENEA-Casaccia Laboratories). The γ-ray measurements have allowed the quali- and quantitative analysis. The element levels in PM10 with the relative correlations have been determined: basically, the concentrations are very low.Furthermore, the enrichment factors of all elements will be reported in order to understand the natural or anthropogenic origins of the particulate matter: some elements may be attributed to long-range transport phenomena from other natural and/or anthropogenic sources.     

Electrochemical hydride generation for the determination of hydride forming elements by atomic fluorescence spectrometry

The determinations of As, Bi, Ge, Sb and Se were performed by atomic fluorescence spectrometry following their electrochemical hydride generation. An electrochemical hydride generator based on a screw-thread seal arrangement, working in a continuous flow mode was used. The effects of cathode material, shape and area of material, catholyte, sample flow rate, applied current, catholyte solution concentration and interference of transition metals on signal intensity were studied. Five kinds of materials including lead, graphite, copper, tungsten and platinum with different shapes were tested as cathode materials. The signal obtained from a 3-dimensional electrode was higher than that from a 2-dimensional electrode under the same conditions. The signal intensity of Ge in HNO₃ medium within a narrow concentration range of 0.05–0.10 mol L^{− 1} was stronger than that in other acidic medium, such as HCl and H₂SO₄. However, the signal intensity of Ge was rapidly decreased with HNO₃, HCl and H₂SO₄ concentration increasing, and then reached approximately zero. In general, limits of detection and a precision were improved using a graphite cathode in H₃PO₄ medium. The analysis of the reference materials showed good agreement with the certified values for As, Bi, Ge, Sb and Se. The method was successfully applied in the determination of As, Bi, Ge, Sb and Se in traditional Chinese medicine samples.     

Determination of bismuth in atmospheric particulate matter by hydride generation and atomic absorption spectrometry

The particulates are collected on Whatman 41 cellulose filters and decomposed with sulfuric acid and hydrogen peroxide; bismuth is then measured by hydride generation/atomic absorption spectrometry. The detection limis is 0.08 ng m^?3 if 500 m³ of air is filtered through an 11-cm filter. Generally, the precision is better than 10%. The concentrations found in Ghent, Belgium varied between 0.1 and 0.8 ng m^?3. Bismuth was also determined in NBS Orchard leaves (SRM 1571); a value of 98.5 ± 15 ng g^?1 was found.     

Determination of As, Ge, Hg, Pb, Sb, Se and Sn in coal slurries by CVG-ETV-ICP-MS using external or isotopic dilution calibration

A method for the multi-elemental determination of As, Ge, Hg, Pb, Sb, Se and Sn in coal reference materials by slurry sampling chemical vapor generation (CVG) using external calibration and isotopic dilution (ID) calibration and detection by electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) is proposed. As, Ge, Sb, Se and Sn were determined using the external calibration, while, Hg, Pb, Se and Sn were determined by isotopic dilution. About 50–250 mg of sample was mixed with an acid solution, containing aqua regia and HCl, in an ultrasonic bath. For the isotopic dilution calibration, the enriched isotopes ²⁰¹Hg, ²⁰⁶Pb, ⁷⁷Se and ¹¹⁹Sn were added to the slurry in an adequate amount in order to produce an altered isotopic ratio close to 1. The vapor produced by the reaction of the sample slurry with the reducing agent was transported to the vaporizer and trapped in a Ir-treated graphite tube at 200 °C, before vaporization at 2100 °C and transportation of the vapor to the plasma. The accuracy of the method was assured by the analysis of four certified reference coal samples, using external calibration with aqueous solutions, prepared in the same medium and subjected to the same CVG and trapping procedure as the slurries and also by isotopic dilution calibration. The obtained concentrations were in agreement with the certified values, using the t-Student test for a confidence level of 95%. The detection limits (3 s; n = 5) of isotopic dilution, in ng g^− 1, were: 0.4 for Hg, 900 for Pb, 0.3 for Se and 0.2 for Sn. For external calibration, the detection limits, in ng g^− 1, were: 1.6 for As, 0.1 for Ge, 0.3 for Sb, 0.9 for Se and 7.5 for Sn. The relative standard deviations generally were lower than 14%, adequate for slurry analysis.     

Determination of tin in atmospheric particulate matter by hydride generation and atomic absorption spectrometry

A procedure is described for the determination of tin in atmospheric particulate matter collected on Whatman 41 cellulose filters. The samples are decomposed with sulfuric acid and nitric acid, followed by hydrofluoric acid to dissolve residual silicates. The analytical parameters for the hydride generation and the subsequent atomic absorption spectrometric measurements are optimized. Severe memory effects encountered with an automatic generator system are avoided when a manual apparatus is used. The precision of the entire method is within 10%. The detection limit is 0.20 ng m^?3 tin if 500 m³ of air is filtered. The concentrations found in residential and industrial areas varied between 1.8 and 47.5 ng m^?3.     

Determination of trace impurities in titanium dioxide by direct solid sampling electrothermal atomic absorption spectrometry

A true direct solid sampling electrothermal atomic absorption spectrometry method with Zeeman-effect background correction (Analytik Jena ZEEnit 60 AAS) was developed for the determination of As, Cd, Hg, Pb, Sb and Zn in powdered titanium dioxide of pharmaceutical, food and cosmetics grade. The interaction of the titanium matrix and graphite surface of the sample carrier boat in a transversely heated graphite tube atomizer was investigated. Conversion of titanium dioxide to interfering TiO₂–TiC-liquid phase, running out the sampling boat, was observed at temperatures above 2000 °C. The temperature program was optimized accordingly for these volatile analytes in atomization and cleaning steps in order to prevent this interference and to prolong significantly the analytical lifetime of the boat to more than one thousand runs. For all elements, calibration by aqueous standard addition method, by wet-chemically analyzed samples with different content of analytes and/or by dosing one sample in different amounts, were proved as adequate quantification procedures. Linear dynamic calibration working ranges can be considerably expanded up to two orders of magnitude within one measurement run by applying three-field dynamic mode of the Zeeman background correction system. The results obtained by true direct solid sampling technique are compared with those of other independent, mostly wet-chemical methods. Very low limits of detection (3σ criterion) of true solid sampling technique of 21, 0.27, 24, 3.9, 6.3 and 0.9 ng g^− 1 were achieved for As, Cd, Hg, Pb, Sb and Zn, respectively.     

Determination of mercury in airborne particulate matter collected on glass fiber filters using high-resolution continuum source graphite furnace atomic absorption spectrometry and direct solid sampling

A study has been undertaken to assess the capability of high-resolution continuum source graphite furnace atomic absorption spectrometry for the determination of mercury in airborne particulate matter (APM) collected on glass fiber filters using direct solid sampling. The main Hg absorption line at 253.652 nm was used for all determinations. The certified reference material NIST SRM 1648 (Urban Particulate Matter) was used to check the accuracy of the method, and good agreement was obtained between published and determined values. The characteristic mass was 22 pg Hg. The limit of detection (3σ), based on ten atomizations of an unexposed filter, was 40 ng g^− 1, corresponding to 0.12 ng m^− 3 in the air for a typical air volume of 1440 m³ collected within 24 h. The limit of quantification was 150 ng g⁻¹, equivalent to 0.41 ng m⁻³ in the air. The repeatability of measurements was better than 17% RSD (n = 5). Mercury concentrations found in filter samples loaded with APM collected in Buenos Aires, Argentina, were between < 40 ng g⁻¹ and 381 ± 24 ng g⁻¹. These values correspond to a mercury concentration in the air between < 0.12 ng m⁻³ and 1.47 ± 0.09 ng m⁻³. The proposed procedure was found to be simple, fast and reliable, and suitable as a screening procedure for the determination of mercury in APM samples.     

Possibilities and limits of the simultaneous determination of As, Bi, Ge, Sb, Se, and Sn by flow injection-hydride generation-inductively coupled plasma-time-of-flight mass spectrometry (FI-HG-ICP-TOFMS)

A simultaneous multi-elemental measurement of As, Bi, Ge, Sb, Se, and Sn was performed in this study by flow injection-hydride generation-inductively coupled plasma-time-of-flight mass spectrometry (FI-HG-ICP-TOFMS). An off-line pre-reduction treatment using a solution of 5% (m/v) KI and ascorbic acid for 15 min at 80 °C is described by presenting its advantages and disadvantages and compared with the results achieved without pre-reduction. Using optimised conditions the following figures of merit were achieved: limits of detection in the 0.08-0.54 ng ml⁻¹ range and relative standard deviations (RSD) of 1.7-6.7%, respectively. Applying the presented method, two certified reference materials (NIST 1643d freshwater and PACS-2 marine sediment) were analysed to demonstrate the suitability of the method for analysis of real samples. Results obtained from treated samples showed good agreement with certified values while the untreated ones considerably departed from them.     

Simultaneous determination of Cd and Fe in grain products using direct solid sampling and high-resolution continuum source electrothermal atomic absorption spectrometry

Cadmium and iron are antagonistic elements in the sense that they produce different effects in the human body. Both elements have to be determined routinely in grain products, cadmium because of its toxicity, and iron because all grain products, according to Brazilian law, have to contain a minimum of 42 mg kg⁻¹ Fe to combat anemia. A routine screening method has been developed for the quasi simultaneous determination of cadmium and iron using high-resolution continuum source electrothermal atomic absorption spectrometry and direct solid sampling. The primary absorption line at 228.802 nm has been used for Cd, and an adjacent secondary line at 228.726 nm for the determination of Fe. Various chemical modifiers have been investigated, and a mixture of tungsten and iridium, applied as a permanent modifier, showed the best performance; it stabilized Cd up to a pyrolysis temperature of 700 °C and did not over-stabilize Fe. Two atomization temperatures were used sequentially, 1700 °C for Cd and 2600 °C for Fe, because of their significantly different volatilities. The characteristic masses obtained were 0.9 pg for Cd and 1.2 ng for Fe. The limits of detection (3σ, n = 10) were 0.6 μg kg⁻¹ for Cd and 0.5 mg kg⁻¹ for Fe. The relative standard deviation ranged from 3 to 7% for Cd and from 4 to 13% for Fe, which is satisfactory for the purpose. The accuracy of the method was confirmed by the analysis of three certified reference materials; the results were in agreement with the certified values at a 95% confidence interval. The Cd content in the investigated grain products was between 0.9 and 10.5 μg kg⁻¹, but most of them did not contain the required minimum amount of iron.     

Application of atmospheric pressure dielectric barrier discharge plasma for the determination of Se,Sb and Sn with atomic absorption spectrometry

The atomization of hydride-forming elements, Se, Sb and Sn, has been studied with an atmospheric pressure dielectric barrier discharge atomizer. The elements were first converted to hydride through the reaction with NaBH₄. Then the hydride were atomized in the atomizer and detected by atomic absorption spectrometry. The effects of operational parameters such as power, gas flow rate and concentrations of HCl and NaBH₄ were investigated. Compared with other hydride atomization methods, the proposed atomizer shows the following features: (1) small size, which is preferable for the miniaturization of the total analytical system; (2) low temperature, which would be helpful for further improvement in the compactness of the total analytical system; (3) low power consumption, which is also necessary for the development of analytical instrumentation for in situ detection of environmentally important elements. The analytical performance of the atomizer has also been investigated. The detection limits of Sb, Se and Sn obtained with the present method were 13.0, 0.6 and 10.6 μg l^− 1. This detector is a very promising technique for hydride detection.     

Screening of antimony in PVC by solid sampling-graphite furnace atomic absorption spectrometry

The development of two-stage control systems is of great interest when a large number of samples are analysed in order to check that they fulfil certain requirements. If the first stage is carried out using an inexpensive method with a high throughput which makes it possible to filter out the majority of the samples that fulfil the requirements, the procedure is not only less time-consuming but also more economical. Direct determination of metals in solid samples by graphite furnace atomic absorption spectrometry (GFAAS) appears, in principle, to be a suitable analytical technique for screening purposes since it provides sufficiently reliable results in a reasonably short time. In this paper it is applied with satisfactory results to antimony content control in a PVC sample.     

Direct mercury determination in aqueous slurries of environmental and biological samples by cold vapour generation-electrothermal atomic absorption spectrometry

Direct cold vapour generation from aqueous slurries of environmental (marine sediment, soil, coal) and biological (human hair, seafood) samples have been developed using a batch mode generation system coupled with electrothermal atomic absorption spectroscopy. The effects of several variables affecting the cold vapour generation efficiency from solid particles (hydrochloric acid and sodium tetrahydroborate concentrations, argon flow rate, acid solution volume and mean particle size) have been evaluated using a Plackett-Burman experimental design. In addition, variables affecting cold vapour trapping and atomisation efficiency on Ir-treated graphite tubes (trapping and atomisation temperatures and trapping time) have been also investigated. Atomisation and trapping temperatures, trapping time and hydrochloric acid concentration were the significant variables. The 2²+star and 2³+star central composite designs have been used to obtain optimum values of the variables selected. The accuracy of methods have been verified by using several certified reference materials (PACS-1, GBW-07410, NIST-1632c, CRM-397 and DORM-2). A characteristic mass of 390 pg were achieved. The detection limits of methods were in the range of 40-600 ng g⁻¹. A particle size less than 50 μm is adequate to obtain total cold vapour generation of Hg content in the aqueous slurry particles.     

Determination of copper in medicinal plants used as dietary supplements by atomic absorption spectrometry with direct flame solid analysis

An alternative device for the direct solid analysis (DSA) for copper determination by flame atomic absorption spectrometry (FAAS) is proposed. Copper was directly determined in commercial medicinal plants used as dietary supplements. The determination of copper in solid samples by DSA–FAAS was made by using a conventional air–acetylene flame. Between 0.05 and 1.5 mg of each test, sample was weighed directly into a small polyethylene vial connected to the device used for solid introduction into the flame. Test samples were introduced into the flame as a dry aerosol using a T-quartz cell set between the burner and the optical path. The T-quartz cell has a slit in the superior part by which the solid aerosol passes to the flame. A transient signal, evaluated as integrated absorbance, is produced and it is totally integrated in 2 s. Background signals always presented absorbance values less than 0.1. It was found a characteristic mass of 0.8 ng Cu and absolute limit of detection of 1.2 ng (3 s), or 1.2 μg g⁻¹ if a sample mass of 1 mg was used. Optimized conditions for air flow rate, flame stoichiometry, and so on were established as well. No excessive grinding of the samples was needed and samples with particle of size less than 80 μm were used throughout. No statistical difference between the results from the proposed system and those obtained by sample digestion and determination by conventional FAAS was observed. With the proposed procedure, more than 50 test samples can be analyzed in 1 h and it can be easily adapted to conventional spectrometers for FAAS.