Determination of total inorganic iodine in seawater by cathodic stripping square wave voltammetry

A method has been designed for the reduction of iodate to iodide in seawater and subsequent determination of total dissolved iodine as iodide by cathodic stripping square wave voltammetry. The pH of the sample is lowered to about 1-2 and iodate is reduced to iodide with sodium sulfite under this acidic condition. The pH of the sample is then raised to 8-9 before the concentration of iodide is measured.     

Separation of Periodate, Iodate and Iodide on a C-18 Stationary Phase. Dependence of the Retention on the Temperature and Solvent Composition. Monitoring of an Oxidative Cleavage Reaction

The separation of periodate, iodate and iodide can be easily achieved by HPLC on a C-18 column with a mobile phase consisting of acetonitrile and aqueous phosphoric acid, without the need of any mobile phase additives that are often employed. All three iodine species are well separated. Separation factors as high as 16 are observed, and retention factors k between ～0.5 and 8. The retention time of all three ions increases with increasing acetonitrile concentration. The retention time of periodate and iodide decreases with increasing temperature, however, it increases slightly for iodate. An application of the HPLC method that was developed is the monitoring of an oxidative cleavage reaction, the cleavage of the enone-group of the steroid 4-androstene-3,17-dione. Periodate is used as oxidative reagent for this reaction. During the reaction periodate is reduced to iodate, and eventually both iodine species will be present in the reaction mixture, besides the starting material and product. In the final product the remaining iodate ions will be reduced to iodide which can be quantified accurately using the developed HPLC method.     

Influences of stable iodine upon the concentration of radioactive iodine by marine organisms

Uptake and loss of radioactive iodine by marine organisms were studied in the artificial seawater in which the concentration as well as chemical forms of both stable and radioactive iodine were controlled. The concentration factors of radioactive iodine by these organisms were clearly dependent upon the concentration of stable iodide ion in the culture media while the concentration of stable iodate ion did not affect the uptake and loss of radioactive iodine. It was observed that the higher the concentration of iodide ion was in the culture media the shorter the biological half-life of radioactive iodine became, and thus the lower the concentration factor resulted in.     

Pattern formation in the iodate-sulfite-thiosulfate reaction-diffusion system

Sodium polyacrylate-induced pH pattern formation and starch-induced iodine pattern formation were investigated in the iodate-sulfite-thiosulfate (IST) reaction in a one-side fed disc gel reactor (OSFR). As binding agents of the autocatalyst of hydrogen ions or iodide ions, different content of sodium polyacrylate or starch has induced various types of pattern formation. We observed pH pulses, striped patterns, mixed spots and stripes, and hexagonal spots upon increasing the content of sodium polyacrylate and observed iodine pulses, branched patterns, and labyrinthine patterns upon increasing the starch content in the system. Coexistence of a pH front and an iodine front was also studied in a batch IST reaction-diffusion system. Both pH and iodine front instabilities were observed in the presence of sodium polyacrylate, i.e., cellular fronts and transient Turing structures resulting from the decrease in diffusion coefficients of activators. The mechanism of multiple feedback may explain the different patterns in the IST reaction-diffusion system.     

Oscillatory and stationary convective patterns in a reaction driven gravity current

Horizontally propagating chemical fronts are studied in a thin solution layer of the acid-catalyzed chlorite-tetrathionate reaction. Unusual cellular patterns develop when significant amount of autocatalyst is bound to polyelectrolyte with low mobility: both oscillatory and stationary patterns evolve as a result of the interaction between the reaction front and the superposed gravity current. The concentration of the polyelectrolyte regulating the velocity of front propagation serves as a bifurcation parameter for switching between the two basic patterns.     

Propagating fronts in reaction–diffusion systems

Propagating reaction–diffusion fronts constitute one of the paradigms in the realm of the nonlinear chemical phenomena. In this paper different situations are considered. Firstly, we discuss the problem of front propagation in a two‐variable chemical system exhibiting multiple stationary states. Emphasis is put on the question of velocity selection. In section 3 of our contribution, the question of front propagating in spatially modulated and noisy media is addressed. Finally, we also briefly comment on the problem of reaction–diffusion fronts in non‐quiescent media. In this particular scenario we simply aim at introducing the two basic propagation modes, i.e., thin versus distributed reaction fronts, that are identified in our numerical simulations. This revised version was published online in July 2006 with corrections to the Cover Date.     

Kinetics and mechanism of the reaction between thiourea and iodate in unbuffered medium

The significances of thiourea and its derivativesnow spill into nonlinear dynamics in chemistry. A re-markable variety of complex dynamical phenomena,including oscillation, oligooscillation, variable stoichio-metries, autoinhibition, autocatalysis, bistability andbirhythmicity, traveling wave and chemical chaos,have been known in thiourea-based reaction systemsfor some time[1—7]. Also, a series of researches on thekinetics and mechanisms of the oxidations of thiourea,thiourea derivatives and …     

过氧乙酸催化氧化亚硫酸钙的反应动力学

利用间歇式反应装置, 研究了过氧乙酸催化氧化亚硫酸钠的本征反应动力学, 得到各反应物的分级数及表观活化能. 在此基础上, 利用鼓泡式反应装置, 通过改变pH、亚硫酸钙浓度、过氧乙酸浓度、空气流量及温度, 研究了过氧乙酸催化氧化亚硫酸钙的宏观反应动力学.     

The use of iodate and periodate with iodide in the potentiometric titration of arsenite,sulfide, and sulfite with mercury (II)

A new potentiometric method is adopted for the accurate microdetermination of arsenite, sulfide and sulfite. The reductant is added to a known excess of standard iodate or periodate properly acidified with sulfuric acid. To the brown solution containing iodine equivalent to the reductant, an excess of standard iodide solution is added followed by titrating unreacted iodide with mercury (II) potentiometrically using the silver amalgam as indicator electrode. The potential breaks which averaged 350 mV per 0.1 ml of 0.05 M titrant were sharp enough for the precise determination of end points, and hence the high accuracy of the present method. In addition, besides simplicity and rapidity the stoichiometry of the reaction between iodate or periodate with the above reductants is still maintained even with the very low concentration.     

Microchemical determination of lodate and iodide in sea waters by flow injection analysis

A flow injection analysis method for iodate and iodide in sea water is described. The system involves spectrophotometric detection based on the catalytic, fading effect of either iodate or iodide on the indicator reaction of iron (III) thiocyanate and nitrite. With and without an anion-exchange column in the flow conduit, the system allows the determination of iodate and total iodine, respectively; iodide can be found by difference. Both iodate-iodine and total iodine can be determined in the range 0.75 to 150 g/1 on the sea water basis with analysis times of 20 min for iodate-iodine and 9 min for total iodine. The RSDs are within 1.3% for both iodate and iodide. Results are presented for the determination of iodate and iodide in sea waters and some brines associated with natural methane gas evolution.     

Control and coupling of spiral waves in excitable media

We report the complex dynamics of spiral waves observed in the ferroin-catalyzed BZ reaction. The reaction is run in an open unstirred reactor (CFUR) with the catalyst immobilized on a polysulfone membrane. The catalyst-loaded membrane is placed between two well stirred compartments which are fed with solutions of sulfuric acid/malonic acid/bromide and sulfuric acid/bromate, respectively. An electrical field perpendicular to the membrane can be applied via Pt-ring electrodes or, alternatively, via transparent electrodes made of ITO-coated glass. In the field-free case relatively simple target and spiral patterns are observed in the membrane. If an alternating electrical field is applied the spiral core drifts through the membrane. The actual trajectory of the spiral tip depends on the amplitude and frequency of the applied electrical field. If the perturbation parameters are chosen properly the wave fronts break up and new spiral cores emerge under the influence of the alternating field. Complex spatio-temporal patterns may be induced which are reminiscent of "spiral-chaos". After switching off the perturbation the system returns to its previous, "simple" behaviour. Our experimental observations are confirmed by model calculations based on the Barkley model of spiral waves. The technique of using modulated excitability to control the dynamics of spiral waves is further extended to the coupling of two spirals in two CFURs. We present numerical simulations based on two identical excitable reaction-diffusion (RD) systems which are mutually coupled. The coupling is based on the observation of an arbitrarily chosen point inside each of the RD systems: If a chemical wave passes the point of optical observation in system 1 an electric field is applied to system 2 and vice versa. Thus, a local observation made in one system is transformed in a global perturbation of the second CFUR. We report the observation of CFUR states where the two spiral waves are spatially and temporally coupled to each other.     

多相条件下亚硫酸镁非催化氧化反应动力学及机理

副产物的氧化回收利用是影响镁法脱硫工艺发展的关键.本文通过真空旋转蒸发的方式制备了高纯度的亚硫酸镁样品,并利用鼓泡式反应装置,研究了亚硫酸镁非催化氧化的反应动力学,考察了pH、氧分压、亚硫酸镁浓度、气体流量、温度等因素对亚硫酸镁氧化反应速率的影响,得到了各反应物的分级数及表观活化能.结合三相反应过程的数学模型推断出亚硫酸镁氧化的本征反应在慢反应区进行,且氧的传质扩散是总反应的速率控制步骤.研究结果为氧化回收镁法脱硫副产物提供了理论依据.     

Elimination of Anti-spiral Waves by Local Inhomogeneity in Oscillatory Systems

Anti-spiral waves are controlled in an oscillatory system by using a local inhomogeneity. The inhomogeneity acts as a wave source, and gives rise to the propagating plane waves. It is found that there is a critical pacemaking domain size below which no wave will be created at all. Two types of ordered waves (target waves and traveling waves) are created depending on the geometry of the local inhomogeneity. The competition between the anti-spiral waves and the ordered waves is discussed. Two different competition mechanisms were observed, which are related to the ordered waves obtained from different local inhomogeneities. It is found that traveling waves with either lower frequency or higher frequency can both eliminate the anti-spiral waves, while only the target waves with lower absolute value of frequency can eliminate the anti-spiral waves.This method also applies to outwardly rotating spiral waves. The control mechanism is intuitively explained and the control method is easily operative.     

Dissipative structures in systems of diffusion-bonded chemical nano- and micro oscillators

In spatially extended classical Belousov-Zhabotinsky (BZ) reaction, trigger spiral or concentric waves usually occur. If the BZ reaction is dispersed into nanodroplets of water-in-oil emulsion, new patterns are observed such as standing waves, anti-spirals, oscillons, dash-waves, jumping waves, Turing patterns, and other. If the size of water droplets is increased up to tens of micrometers, coupled micro-oscillators produce new stationary and oscillatory discrete dissipative patterns. In the review, comparative analysis of these patterns is done and a possibility of creating a chemical computer on the basis of dissipative patterns is discussed.     

Mechanism and reaction rate of the karl-fischer titration reaction: Part III. Rotating ring-disk electrode measurements— comparison with the aqueous system

A platinum disk-platinum ring electrode was used to investigate the oxidation of sulfur dioxide by iodine and triiodide in aqueous solutions. Contrary to methanolic solutions, where the monomethyl sulfite ion is the only oxidizable species, in aqueous solutions both the hydrogen sulfite ion and the sulfite ion can be oxidized. The reaction rate was generally so high, that the method for measurements of homogeneous second order reactions had to be used. At pH values >5, the reaction proceeded too fast to be measured reliably. In a solution “diluted” with ethanol (50% of weight), however, the reaction rate was within the range where a rotating ring-disk electrode can be applied to measure fast homogeneous reactions. At very low pH values both the first order calculation technique and the second order method could be used. The results with both methods were in fair agreement.     

Highly Selective Photometric Method for the Determination of Periodate

ABSTRACT

A simple and selective photometric procedure was developed for the micro-determination of periodate in aqueous media. The method is based on the reaction of periodate with Gallocyanine at pH = 4.8. The reaction was monitored photometrically by measuring the absorbance of the reaction mixture at 620 nm. The effects of reagent concentration, temperature and influence of other species for the determinations of periodate were investigated. Periodate can be determined in the range of 0.02-2.20 μg/ml, with a relative standard deviation of 1.96% for ten replicate measurements of 0.13 μg/ml periodate. Periodate can be determined in the presence of iodate or iodide.     

Front waves in the NO + NH3 reaction on Pt{100}

In the present work, we spatially extended a brand new kinetic mechanism of the NO + NH3 reaction on Pt{100} to simulate the experimentally observed spatiotemporal traveling waves. The kinetic mechanism developed by Irurzun, Mola, and Imbihl (IMI model) improves the former model developed by Lombardo, Fink, and Imbihl (LFI model) by replacing several elementary steps to take into account experimental evidence published since the LFI model appeared. The IMI model achieves a better agreement with the experimentally observed dependence of the oscillation period on temperature. In the present work, the IMI model is extended by considering Fickean diffusion and coupling via the gas phase. Traveling waves propagating across the surface are obtained at realistic values of temperature and partial pressure. A transition from amplitude to phase waves is observed, induced either by temperature or by the gas global coupling strength. The traveling waves simulated in the present work are not associated with fixed defects, in agreement with experimental evidence of spiral centers capable of moving on the surface. Also, the IMI model adequately predicts the presence of macroscopic oscillations in the partial pressures of the reactants coexisting with front wave patterns on the surface.     

Microdetermination of sulfite with a piezoelectric crystal detector

A piezoelectric method is proposed for the determination of sulfite in concentration range 1 × 10^–7–1 × 10^–5 mol/1. The method is based on the redox reaction of sulfite with iodine followed by measuring frequency change of the piezoelectric crystal caused by the unreacted iodine. The method is applied to the determination of sulfite in liquor.     

The hydrogen peroxide–iodic acid–manganese (ii)–acetone oscillating system: Further observations

The redox potential and iodine concentration behavior of the title reaction and component reactions have been examined. The effect of hydrogen peroxide, potassium iodate, manganese (II) sulfate, sulfuric acid, and acetone concentration on the time period and redox potential behavior is reported. Iodine production and consumption rates for the component reactions are given, and some mechanistic suggestions, involving iodine dioxide as the one electron oxidant, are made.