Spectrophotometric Determination of Tetracyclines in Pure Form and in Pharmaceutical Preparations,by a Molybdenum Blue Method

Abstract

A new and sensitive spectrophotometric method has been developed for the determination of tetracyclines either in a pure form or in Pharmaceuticals, by a molybdenum blue method. The procedure is based on the observation that, in sulphuric acid medium, tetracyclines reduce ammonium molybdate to molybdenum blue, the absorbance of which is proportional to the amount of antibiotic present. The variables affecting development of the color have been investigated and the conditions optimized. Beer's law is obeyed for up to 20 μg/ml of tetracycline HCl and oxytetracycline HCl, 28 μg/ml of demeclocycline HCl, 18 μg/ml of chlortetracycline HCl, 32 μg/ml of doxycycline HCl and 40 μ/ml of rolitetracycline. Molar absorptivities (1 mol^?1 cm^?1) and Sandell's sensitivities (μ cm^?2 per 0.001 absorbance unit) are, respectively: tetracycline HCl 4.9×10⁴ and 0.0098, oxytetracycline HCl 5.4×10⁴ and 0.0092, demeclocycline HCl 1.6×10⁴ and 0.0313, chlortetracycline HCl 5.5×10⁴ and 0.0094, doxycycline HCl 3.4×10⁴ and 0.0141, rolitetracycline 2.7×10⁴ and 0.0195.     

Spectrophotometric Determination of Dextromethorphan Hydrobromide and Ketamine Hydrochloride in Pure and Dosage Forms

Three simple, sensitive and accurate spectrophotometric methods have been developed for the determination of dextromethorphan hydrobromide (DEX) and ketamine hydrochloride (KET) in dosage forms. These methods are based on the formation of ion‐pair complexes with bromocresol green (BCG), bromocresol purple (BCP), and bromophenol blue (BPB) in acidic medium. The coloured ion‐pair products are measured at 419, 409 and 417 nm for DEX and at 417, 408 and 416 nm for KET using BCG, BCP and BPB, respectively. Beer's law was obeyed in the range of 2.0–22 μg mL^?1 for DEX and 2.0–16 μg mL^?1 for KET. The composition of the ion‐pair was established by continuous variation and molar ratio methods. The proposed methods were applied successfully for the determination of DEX and KET in dosage forms applying the standard addition technique and compared statistically with the official methods. The molar absorptivity, Sandell sensitivity, detection and quantification limits were also calculated.     

Study on the Color Reaction of Silver with 2‐(2‐Quinolylazo)‐5‐Dimethylaminoaniline and its Application

A new chromogenic reagent, 2‐(2‐quinolylazo)‐5‐dimethylaminoaniline (QADMAA) was synthesized. A highly sensitive, selective and rapid method for the determination of silver based on the rapid reaction of silver(I) with QADMAA was developed. In the presence of pH = 6.5 sodium citrate‐sodium hydroxide buffer solution and sodium dodecyl sulfonate (SDS) medium, QADMAA reacts with silver to form a violet complex of a molar ratio 1:2 (silver to QADMAA). The molar absorptivity of the complex is 1.26 × 10⁵ L. mol^?1.cm^?1 at 570 nm. Beer's law is obeyed in the range of 0.01–0.6 μg/mL. The relative standard deviation for eleven replicate samples of 0.2 μg/mL silver is 1.76%. This method was applied to the determination of silver in water with good results.     

Determination of Cinnarizine in Pure and Pharmaceutical Formulations

Two simple, rapid and sensitive extractive spectrophotometric methods have been developed for the assay of cinnarizine (CNR) in pure and pharmaceutical formulations. The methods are based on the formation of chloroform soluble ion‐association complexes of CNR with thymol blue (TB) and with cresol red (CR) inNaOAc‐AcOH buffer of pH 3.6 for TB and in KCl‐HCl buffer of pH 1.6 for CR with absorption maxima at 405 nm and at 403 nm for TB and CR, respectively. Reaction conditions were optimized to obtain the maximum color intensity. The systems obeyed Beer's law in the range of 0.6–15.8 and 0.8–16.6 μg mL^?1 for TB and CR, respectively. Various analytical parameters have been evaluated and the results have been validated by statistical data.     

Development and validation of a generic RP‐HPLC PDA method for the simultaneous separation and quantification of active ingredients in cold and cough medicines

A novel generic reverse phase high performance liquid chromatography (RP‐HPLC) method is developed and validated for simultaneous determination of seven pharmaceutically active ingredients, namely, acetaminophen, dextromethorphan, doxylamine, phenylephrine, guaifenesin, caffeine and aspirin. All seven ingredients were quantified in soft gel, syrup and tablet formulations of the over‐the‐counter US‐marketed products, as per the guidelines of the International Conference on Harmonization. The separation was achieved in a 16 min run time on an Agilent Zorbax Phenyl column using a gradient method with two mobile phases. Mobile phase A was 0.15% trifluoro acetic acid in purified water and while mobile phase B was a mixture of acetonitrile and methanol (750:250 v/v) with 0.02% trifluoro acetic acid. The flow rate was 1.0 mL min^?1 and injection volume was 10 μL. Detection was performed at 280 nm using a photodiode array detector. As part of the method validation, specificity, linearity, precision and recovery parameters were verified. The concentration and area relationships were linear (R² > 0.999), over the concentration ranges 20–120 μg mL^?1 for acetaminophen, 75–450 μg mL^?1 for dextromethorphan, 31.25–187.5 μg mL^?1 for doxylamine, 25–150 μg mL^?1 for phenylephrine, 25–150 μg mL^?1 for aspirin, 6.5–39 μg mL^?1 for caffeine and 12–72 μg mL^?1 for guaifenesin. The relative standard deviations for precision and intermediate precision were <1.5%. The proposed RP‐HPLC generic method is applicable for routine analysis of cold and cough over‐the‐counter products.     

Comparison of C18 silica and multi‐walled carbon nanotubes as the adsorbents for the solid‐phase extraction of Chlorpyrifos and Phosalone in water samples using HPLC

A comparison between C₁₈ silica and multi‐walled carbon nanotubes (MWCNTs) in the extraction of Chlorpyrifos and Phosalone in environmental water samples was carried out using HPLC. Parameters affecting the extraction were type and volume of elution solvent, pH and flow rate of sample through the adsorbent. The optimum conditions obtained by C₁₈ cartridge for adsorption of these pesticides were 4 mL dichloromethane as elution solvent, sample pH of 5, flow rate of 1 mL/min, and those for MWCNT cartridge were 3 mL dichloromethane, pH of 5 and flow rate of 10 mL/min, respectively. Optimized mobile phase for separation and determination of these compounds by HPLC was methanol/water (80:20 v/v) with pH=5 (adjusted with phosphate buffer). Under optimal chromatographic and SPE conditions, LOD, linear range and precision (RSD n=8) were 3.03×10^?3, 0.01–5.00 μg/mL and 2.7% for Chlorpyrifos and 4.03×10^?4, 0.01–5.00 μg/mL and 2.3% for Phosalone, in C₁₈ cartridge, respectively. These values for MWCNT were 4.02×10^?6, 0.001–0.500 μg/mL and 1.8% for Chlorpyrifos and 1.02×10^?6, 0.001–0.500 μg/mL and 1.5% for Phosalone, respectively.     

ABTS‐Multiwalled Carbon Nanotubes Nanocomposite/Bi Film Electrode for Sensitive Determination of Cd and Pb by Differential Pulse Stripping Voltammetry

A 2,2′‐azinobis (3‐ethylbenzothiazoline‐6‐sulfonate) diammonium salt (ABTS)‐multiwalled carbon nanotubes (MWCNTs) nanocomposite/Bi film modified glassy carbon (GC) electrode was constructed for the differential pulse stripping voltammetric determination of trace Pb²⁺ and Cd²⁺. This electrode was more sensitive than ABTS‐free Bi/GC and Bi/MWCNTs/GC electrodes. Linear responses were obtained in the range from 0.5 to 35 μg L^?1 for Cd²⁺ and 0.2 to 50 μg L^?1 Pb(II), with detection limits of 0.2 μg L^?1 for Cd²⁺ and 0.1 μg L^?1 for Pb²⁺, respectively. This sensor was applied to the simultaneous detection of Cd²⁺ and Pb²⁺ in water samples with satisfactory recovery.     

Study on the Solid Phase Extraction of Hg(II)‐ABR Chelate with C18 Disks and its Application to the Determination of Mercury in Tobacco and Tobacco Additives

A highly sensitive, selective and rapid method for the determination of mercury based on the rapid reaction of mercury(II) with 5‐(p‐aminobenzylidene)‐rhodanine (ABR) and the solid phase extraction of the colored chelate with C₁₈ disks has been developed. In the presence of pH = 3.5 sodium acetate‐acetic acid buffer solution and Emulsifier‐OP medium, ABR reacts with mercury(II) to form a red chelate of a molar ratio 1:2 (mercury to ABR). This chelate was enriched by the solid phase extraction with C₁₈ disks and eluted the retained chelate from the disks with dimethyl formamide (DMF). The enrichment factor of 50 was achieved. In the DMF medium, the molar absorptivity of the chelate is 1.16 × 10⁵ L.mol^?1.cm^?1 at 540 nm. Beer's law is obeyed in the range of 0.01?3 μg/mL in the measured solution. The relative standard deviation for eleven replicated samples of 0.01 μg/mL level is 1.83%. This method was applied to the determination of mercury in tobacco and tobacco additives with good results.     

2‐Aminocyclopentene‐1‐Dithiocarboxylic Acid‐Naphthalene Adsorbent for the Preconcentration and Determination of a Trace Copper in Real Samples by Spectrophotometric Method

A solid uncharged complex produced from 2‐aminocyclopentene‐1‐dithiocarboxylic acid (synthetic reagent) on naphthalene provides a very sensitive, selective and economical method for the preconcentration and determination of trace amounts of copper in drug and alloy samples. The 2‐aminocyclopentene‐1‐dithiocarboxylate of copper is retained quantitatively on microcrystalline naphthalene in the pH range 2.8–3.3. After filtration the solid mass consisting of copper complex‐naphthalene is dissolved with 4 mL of dimethylformamide (DMF). The absorbance is measured at 462 nm with a spectrophotometer against the reagent blank and molar absorptivity found to be 2.8 × 10⁵ liter mol^?1 cm^?1. Beer's law is obeyed over the concentration range of 0.1–16.0 μg of copper in 4 mL of the dimethylformamide solution. Detection limit is 3 ng mL^?1 [signal to noise ratio = 2]. Ten replicate determinations on a sample containing 1 μg of copper gave a relative standard deviation of 0.76%. The interference of a large number of anions and cations have been studied and the optimized conditions developed were utilized for determination of copper in various real samples.     

Electrochemical Sensing of NADH and Glutamate Based on Meldola Blue in 1,2‐Diaminobenzene and 3,4‐Ethylenedioxythiophene Polymer Films

The redox mediator Meldola blue (MB) was entrapped into two polymers, poly‐1,2‐diaminobenzene (p‐DAB) and poly‐3,4‐ethylenedioxythiophene (p‐EDOT) by potential cycling and films were applied to NADH oxidation with subsequent glutamate detection using immobilized glutamate dehydrogenase. Both polymer films were tested for electrocatalysis of NADH using amperometry at E_app=0.1 V vs. Ag/AgCl and similar response characteristics were obtained with sensitivity values of 6.1 nA μM^?1, linear range up to 0.5 mM (R²=0.9972) and LOD of 50 μM. Subsequent amperometric determination of glutamate resulted in sensitivity 0.7 nA μM^?1, linearity 0–100 μM and detection limit of 2 μM glutamate.     

Cetyl‐alcohol‐reinforced hollow fiber solid/liquid‐phase microextraction and HPLC–DAD analysis of ezetimibe and simvastatin in human plasma and urine

A new cetyl‐alcohol‐reinforced hollow fiber solid/liquid‐phase microextraction (CA–HF–SLPME) followed by high‐performance liquid chromatography–diode array detection (HPLC–DAD) method was developed for simultaneous determination of ezetimibe and simvastatin in human plasma and urine samples. To prepare the CA–HF–SLPME device, the cetyl‐alcohol was immobilized into the pores of a 2.5 cm hollow fiber micro‐tube and the lumen of the micro‐tube was filled with 1‐octanol with the two ends sealed. Afterwards, the prepared device was introduced into 10 mL of the sample solution containing the analytes with agitation. Under optimized conditions, calibration curves plotted in spiked plasma and urine samples were linear in the ranges of 0.363–25/0.49–25 μg L^?1 for ezetimibe/simvastatin and 0.193–25/0.312–25 μg L^?1 for ezetimibe/simvastatin in plasma and urine samples, respectively. The limit of detection was 0.109/0.174 μg L^?1 for ezetimibe/simvastatin in plasma and 0.058/0.093 μg L^?1 for ezetimibe/simvastatin in urine. As a potential application, the proposed method was applied to determine the concentration of selected analytes in patient plasma and urine samples after medication and satisfactory results were achieved. In comparison with reference methods, the CA–HF–SLPME–HPLC–DAD method demonstrates considerable potential in the biopharmaceutical analysis of selected drugs.     

Design and synthesis of novel cytotoxic agents based on combined framework of quinoline and nimesulide

Functionalization of quinoline aldehydes, derived from nimesulide framework was carried out using Morita–Baylis–Hillman (MBH) chemistry. A number of novel quinoline‐based diverse MBH adducts was prepared via the reaction of derivatives of 2‐chloroquinoline‐3‐carbaldehyde and various activated alkenes in good yields. Many of these compounds were found to be potent when tested against human prostate cancer (Pc‐3) cell line in vitro. Among all the compounds tested N‐(2‐chloro‐3‐(2‐cyano‐1‐hydroxyallyl)‐7‐phenoxyquinolin‐6‐yl)formamide (IC₅₀ = 1.2 μg mL^?1) was identified as the most potent compound in this series. J. Heterocyclic Chem., (2012).     

Analysis of Cembranoids in Flue‐cured Tobacco by Accelerated Solvent Extraction and Gas Chromatography‐Mass Spectrometry‐Selected Ion Monitoring

An efficient and sensitive analytical method based on accelerated solvent extraction (ASE) and gas chromatography‐mass spectrometry‐selected ion monitoring (GC‐MS‐SIM) was developed and validated for analysis of cembranoids in flue‐cured tobacco leaves. Extraction efficiency of different pretreatment methods including liquid‐solid extraction (LSE), ultrasound‐assisted extraction (UAE), Soxlet extraction and accelerated solvent extraction (ASE) was compared and ASE was chosen as the optimal extraction method. During ASE procedure, effect of four parameters on extraction efficiency was considered and the experimental conditions were selected as follows: extraction solvent: dichloromethane; oven temperature: 50 °C; static time: 5 min and number of cycles: 2. Working standards of cembranoids were isolated by silica gel column chromatography and the identification was performed by mass spectrometry. Performance characteristics such as linearity, limit of detection (LOD), limit of quantitation (LOQ), precision and recovery were studied. The LOD and LOQ values were ranging from 5.0 × 10^?3 to 6.9 × 10^?3 μg/mL and 1.7 × 10^?2 to 2.3 × 10^?2 μg/mL for all analytes. At three different spiked levels, recoveries for CBT‐ol, α‐CBT‐diol and β‐CBT‐diol were 94.6%‐105.1%, 93.0%‐97.2% and 88.7%‐107.5% while the relative standard deviations (RSDs) were in the ranges of 3.9%‐6.2%, 1.8%‐8.7% and 1.7%‐6.0%, respectively. The proposed analytical methodology was successfully applied in the analysis of cembranoids in tobacco samples.     

Silver‐109‐based laser desorption/ionization mass spectrometry method for detection and quantification of amino acids

A new methodology applicable for both high‐resolution laser desorption/ionization mass spectrometry and mass spectrometry imaging of amino acids is presented. The matrix‐assisted laser desorption ionization‐type target containing monoisotopic cationic ¹⁰⁹Ag nanoparticles (¹⁰⁹AgNPs) was used for rapid mass spectrometry measurements of 11 amino acids of different chemical properties. Amino acids were directly tested in 100,000‐fold concentration change conditions ranging from 100 μg/mL to 1 ng/mL which equates to 50 ng to 500 fg of amino acid per measurement spot. Limit of detection values obtained suggest that presented method/target system is among the fastest and most sensitive ones in laser mass spectrometry. Mass spectrometry imaging of spots of human blood plasma spiked with amino acids showed their surface distribution allowing optimization of quantitative measurements.     

Determination and speciation of selenium in water samples collected from Muğla (Turkey) province by hydride generation atomic absorption spectrometry

In this work, determination of selenium in various water samples was done by using hydride generation atomic absorption spectrometry. The most appropriate values of HCl concentration, NaBH₄ concentration, NaOH concentration, flow rate of argon and flow rate of waste solution were determined. The optimum concentration of the HCl, NaBH₄ and NaOH solutions were found to be 7.0 mol L^?1, 1.0% and 0.75%, respectively. The optimum flow rate of Ar gas and waste solution were also found to be 100.9 mL min^?1 and 4.0 mL min^?1, respectively. Values of LOD and LOQ were calculated separately for total Se and Se(IV). LOD and LOQ values were calculated 0.56 μg L^?1, 1.87 μg L^?1 for total Se and 0.72 μg L^?1, 2.40 μg L^?1 for Se(IV), respectively. The precision was evaluated by relative standard deviation (RSD%) was found to be 3.5% for total Se and 3.1% for Se(IV) (n = 11). A standard reference material (NIST 1643e) was used in order to check the accuracy of the proposed method. There was a good agreement between certified and found values for standard reference material. The method was applied to the analysis of total Se and Se(IV) concentrations in tap water samples collected from the various regions of Mu?la. Proposed method showed spike recovery ranges from 92% to 116% in water samples.     

Disposable Bismuth Oxide Screen Printed Electrodes for the High Throughput Screening of Heavy Metals

We present a simplified approach for the trace screening of toxic heavy metals utilizing bismuth oxide screen printed electrodes. The use of bismuth oxide instead of toxic mercury films facilitates the reliable sensing of lead(II), cadmium(II) and zinc(II). A linear range over 5 to 150 μg L^?1 with detection limits of 2.5 and 5 μg L^?1 are readily observed for cadmium and lead in 0.1 M HCl, respectively. Conducting a simultaneous multi‐elemental voltammetric detection of zinc, cadmium and lead in a higher pH medium (0.1 M sodium acetate solution) exhibited a linear range between 10 and 150 μg L^?1 with detection limits of 5, 10 and 30 μg L^?1 for cadmium, lead and zinc respectively. The sensor is greatly simplified over those recently reported such as bismuth nanoparticle modified electrodes and bismuth film coated screen printed electrodes. The scope of applications of this sensor with the inherent advances in electroanalysis coupled with the negliable toxicity of bismuth is extensive allowing high throughput electroanalysis.     

Trace Detection of Mercury(II) Using Gold Ultra‐Microelectrode Arrays

The electroanalytical detection of trace mercury(II) at gold ultra‐microelectrode arrays is reported. The arrays consist of 256 gold microelectrodes of 5 μm in diameter in cubic arrangements which are separated from their nearest neighbor by 100 μm. The array was utilized in nitric acid using linear sweep voltammetry where a linear response from mercury additions over the range 10 μg L^?1?200 μg L^?1 (10^?8?10^?6 M) was observed with a sensitivity and detection limit of 0.11 nC/μg L^?1 and 3.2 μg L^?1 (16 nM) respectively from using a deposition time of 30 s at ?0.2 V (vs. SCE). This methodology was explored in 0.1 and 1 M chloride media over the mercury range 10 μg L^?1?200 μg L^?1 (5×10^?8?10^?6 M) where similar sensitivities of 0.087 nC/μg L^?1 and 0.078 nC/μg L^?1 were observed with an identical detection limit. The protocol is demonstrated to be useful for the determination of mercury for analysis of environmental water samples.     

Colorimetric Determination of Sulphur Dioxide and Sulphites in Various Environmental Samples

Rhodamine‐B has been proposed as a simple and sensitive colorimetric reagent for the estimation of sulphur dioxide in air. The air sample containing sulphur dioxide is passed through the absorbing solution of aqueous potassium iodate and N‐chlorosuccinimide to liberate iodine. The liberated iodine bleaches the pinkish red coloured rhodamine‐B dye, which measured at 555 nm. Beer's law was obeyed in the range of 0.5–5.0 μg, of sulphite per 25 mL (0.02–0.2 ppm) equivalent to 0.4–4.0 μg of sulphur dioxide (0.016–0.16 ppm). The molar absorptivity and Sandell's sensitivity were found to be 4.56 × 10⁵ l mol^?1 cm^?1 and 0.00017 μg cm^?2, respectively. The method has been suitably modified and successfully applied to the determination of sulphites in water after liberation of sulphur dioxide in acidic medium.     

UV–Second Derivative Spectrophotometric and Colorimetric Methods for the Determination,Validation and Thermogravimetric Analysis of New Oral Antidiabetic Pioglitazone in Pure and Pharmaceutical Preparations

Abstract

Three rapid, sensitive, and simple spectrophotometric methods have been developed for the determination of pioglitazone in pure and pharmaceutical preparations.

For the first method, UV-spectrophotometry, standard solutions were measured at 270.2 nm. The first method was linear from 5.0–20.0 µgmL^?1. The linearity was found to be 5.0–20.0 µgmL^?1. For the second method, the distances between two extremum values (peak-to-peak amplitudes), 272.0 and 287.4 nm were measured in the second order derivative-spectra of standard solutions. Calibration curves were constructed by plotting d² A/dλ² values against concentrations, 2.0–12.0 µgmL^?1 of pioglitazone standards in acetonitrile. The detection limits of pioglitazone were 0.10 and 0.16 µgmL^?1 for UV and derivative spectrophotometric methods, respectively. The third method was based on the formation of an ion association complex with bromocresol green (BCG), bromocresol purple (BCP), bromophenol blue (BPB), and bromothymol blue (BTB). The assay was linear over the concentration range of 20.0–100.0 µgmL^?1 for BCG, 10.0–100.0 µgmL^?1 for BCP, 20.0–120.0 µgmL^?1 for BPB, and 10.0–100.0 µgmL^?1 for BTB. The detection limits of pioglitazone was found to be 0.14 µg mL^?1 for BCG, 0.32 for BCP, 1.24 µgmL^?1 for BPB, and 0.22 µgmL^?1 for BTB. The thermal analysis of the pioglitazone was studied by Thermogravimetric Analysis-Differential Scanning Calorimetry (TGA-DSC) techniques. Enthalpy change of pioglitazone was found to be 85.16 J/g. The proposed methods were validated according to the ICH guidelines (1996) with respect to specificity, linearity, limits of detection and quantification, accuracy, precision, and robustness. The results demonstrated that the procedure is accurate, precise, specific, and reproducible (percent relative standard deviation <2%), while being simple and less time consuming. The three proposed methods have been successfully applied to the assay of pioglitazone in pure and in pharmaceutical preparations. The results compared with those obtained by an ultraviolet spectrophotometric method using t and F tests.     

Differential Pulse Polarographic Determination of Cd(II) and Pb(II) in Milk Samples after Solid‐Phase Extraction Using Amberlite XAD‐2 Resin Modified with 2,2′‐DPED3P

In the present paper novel column solid phase extraction procedure was developed for the determination of Cd(II) and Pb(II) in cows', goats', ewes', buffalos' and humans' milk samples using newly synthesized reagent 2,2′‐DPED₃P (2,2′‐{[1,2‐diphenylethane‐1,2‐diylidene]dinitrilo}diphenol) for preconcentration and separation prior to differential pulse polarography using amberlite XAD‐2 in the ranges of pH 4.0–5.0. The sorbed elements were subsequently eluted with 10 mL of 2 M HCl elutes were analysed by differential pulse polarography (DPP). The interference of foreign ions has also been studied. Effects of various instrumental parameters are investigated and received conditions are optimized. The total metal concentration of the milk samples in the study area were in the following ranges 0.030–0.090 μg L^?1 of Cd(II), 0.009–0.026 μg L^?1 of Pb(II) respectively. The limits of detections were found to be 0.020 and 0.024 μg L^?1 for Cd(II) and Pb(II) respectively by applying a preconcentration factor ～40. The proposed enrichment method was applied successfully for the determination of metal ions in cows', goats', ewes', buffalos' and humans' milk samples.