Preparation of novel sulfonated block copolyimides for proton conductivity membranes

In this article novel sulfonated block copolyimides with various diamine compositions and block chain lengths were synthesized by chemical imidization using a two‐pot procedure. The proton conductivities of the block copolyimide membranes were measured as functions of the relative humidity and temperature using four‐point‐probe electrochemical impedance spectroscopy. The proton conductivity of the membranes strongly depended on the block chain lengths and increased with an increase in the block chain lengths. The proton conductivity of NTDA‐BDSA‐b‐6FAP (112/48) as the block copolyimide membrane was approximately 0.35 S cm⁻¹ which indicated a higher value when compared to that determined for Nafion®. Copyright © 2005 John Wiley & Sons, Ltd.     

Synthesis and characterization of sulfonated homo‐ and co‐polyimides based on 2,4 and 2,5‐diaminobenzenesulfonic acid for proton exchange membranes

A series of sulfonated homo‐ and random co‐polyimides (co‐SPI) based on 2,4‐diaminobenzenesulfonic acid (2,4‐DABS) and 2,5‐diaminobenzenesulfonic acid (2,5‐DABS) has been synthesized via conventional two‐step polyimidization method. 2,4‐DABS and 2,5‐DABS were used as sulfonated diamine compounds, 4,4′‐oxydianiline (ODA) and 4,4′‐diaminodiphenyl sulfone (DDS) were used as non‐sulfonated diamine compounds. Mixtures of sulfonated and non‐sulfonated diamine compounds were reacted with benzophenonetetracarboxylic dianhydride (BTDA) to obtain co‐SPI membranes. Molar ratios of sulfonated to non‐sulfonated diamine were systematically varied to produce copolymers of controlled compositions. The co‐SPIs were evaluated for thermal oxidative stability, ion exchange capacity (IEC), water uptake, proton conductivity, solubility, and hydrolytic stability. Proton conductivity and hydrolytic stability of the co‐SPIs were compared with the fully aromatic polyimide, homo‐SPIs (BTDA/2,4‐DABS and BTDA/2,5‐DABS). Regarding thermogravimetric analysis (TGA) analysis, it is concluded that desulfonation temperature in the range of 200–350°C suggests high stability of sulfonic acid groups. co‐SPIs with 40 mol% of 2,4‐DABS showed similar or higher proton conductivity than Nafion® 117 in water. Proton conductivity values of the co‐SPIs were mainly a function of IEC and water uptake. Consequently, the optimum concentration of 2,4‐DABS was found to be in the range of 30–40 mol% from the viewpoint of proton conductivity, IEC, and hydrolytic stability. Copyright © 2008 John Wiley & Sons, Ltd.     

Some aromatic polyimides based on diamines containing hydrazo group and ether linkages

Three new hydrazo-bridged diamines, 4,4′-bis [4-(4-aminophenyloxy) phenylhydrazyl] biphenyl (BPD-2), 4,4′-bis [4-(4-aminophenyloxy) phenylhydrazyl] biphenyl ether (SPD-2) and 4,4-bis [4-(4-aminophenyloxy) phenyl] hydrazine (APD-2), were synthesized by the reduction of three azo-diols, 4,4′-bis (4-azo-1-hydroxyphenyl) biphenyl (BPD), 4,4′-bis (4-azo-1-hydroxyphenyl) biphenyl ether (SPD) and azo-4-hydroxybenzene (APD), and polymerized with pyromellitic dianhydride (PM), 3,3′,4,4′-benzophenone tetracarboxylic acid dianhydride (BP) and 3,4,9,10-perylenetetracarboxylic acid dianhydride (PR) either by one-step solution polymerization or by two-step procedure which includes ring-opening polyaddition to give poly(amic acid) followed by cyclic dehydration to polyimide. The monomers and polyimides were characterized by their elemental analyses, FTIR and ¹H NMR spectroscopy. Glass transition temperatures of the polymers are quite high (175-310 °C), characteristic of polyimides. The decomposition temperatures for 10% weight loss fall in the range of 280-575 °C in nitrogen. Activation energies of pyrolysis for each of the polymers calculated from Horowitz and Metzger's method are also high (52.54-95.28 kJ mol⁻¹). The inherent viscosities of the polyimides at a concentration of 0.5 g/dl in DMF range from 0.94 to 1.93 dl/g.     

Synthesis and characterization of aromatic polythiazole-amides from new aromatic diamines containing phenyl-pendant thiazole units

New aromatic diamines containing phenyl-pendant thiazole units were synthesized in three steps starting from p-nitrobenzyl phenyl ketone. Novel aromatic polyamides containing phenyl-pendant thiazole units were prepared by the low-temperature solution polyconden-sation of 1,4- (or 1.3-) bis[5-(p-aminophenyl)-4-phenyl-2-thiazolyl] benzene with various aromatic dicarboxylic acid chlorides in N,N-dimethylacetamide. High molecular weight polyamides having inherent viscosities of 0.5–3.0 dL/g were obtained quantitatively. The polythiazole-amides with m-phenylene, 4,4′-oxydiphenylene, and 4,4′-sulfonyldiphenylene units were soluble in N-methyl-2-pyrrolidone, N,N-dimethylacetamide, and pyridine, and gave transparent flexible films by casting from the solutions. These organic solvent-soluble polyamides displayed prominent glass transition temperatures (T_g) between 257 and 325°C. On the other hand, the polythiazole-amides with p-phenylene and 4,4′-biphenylene units were insoluble in most organic solvents, and had no observed T_g. All the polythiazole-amides started to decompose at about 400°C with 10% weight loss being recorded at 450–525°C in air. © 1995 John Wiley & Sons, Inc.     

Synthesis of copolyimides based on room temperature ionic liquid diamines

Block copolyimides based on aromatic dianhydrides and diamines copolymerized with diamino room temperature ionic liquid (RTIL) monomers were synthesized over a range of compositions. Specifically, two diamino RTILs, 1,3‐di(3‐aminopropyl) imidazolium bis[(trifluoromethyl)sulfonyl] imide ([DAPIM] [NTf₂]) and 1,12‐di[3‐(3‐aminopropyl) imidazolium] dodecane bis[(trifluoromethyl) sulfonyl] imide ([C₁₂ (DAPIM)₂] [NTf₂]₂) were synthesized using a Boc protection method. The two RTILs were reacted with 2,2‐bis(3,4‐carboxylphenyl) hexafluoropropane dianhydride (6FDA) to produce 6FDA‐RTILs oligomers that formed the RTIL component for the block copolyimides. The oligomers were reacted with 6FDA and m‐phenylenediamine (MDA) at oligomer concentration from 6.5 to 25.8 mol % to form block copolyimides. Increasing the concentration of the 6FDA‐RTIL oligomer in the block copolyimides resulted in a decrease in the thermal degradation temperature, glass transition temperature and an increase in the density. The gas permeability of the RTIL based block copolyimide decreased but the ideal permeability selectivity for CO₂/CH₄ gas pair increased relative to the pure 6FDA‐MDA. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4036–4046, 2010     

Crosslinked sulfonated polyimide networks as polymer electrolyte membranes in fuel cells

Sulfonated polyimides with tertiary nitrogen in the polymer backbone were synthesized with 1,4,5,8‐naphthalenetetracarboxylic dianhydride, 4,4′‐diaminobiphenyl 2,2′‐disulfonic acid, 2‐bis[4‐(4‐aminophenoxy)phenyl]hexafluoropropane, and diaminoacrydine hemisulfate. They were crosslinked with a series of dibromo alkanes to improve the hydrolytic stability. The crosslinked sulfonated polyimide films were characterized for their thermal stability, ion‐exchange capacity (IEC), water uptake, hydrolytic stability, and proton conductivity. All the sulfonated polyimides had good thermal stability and exhibited a three‐step degradation pattern. With an increase in the alkyl chain length of the crosslinker, IEC decreased as 1.23 > 1.16 > 1.06 > 1.01, and the water uptake decreased as 7.29 > 6.70 > 6.55 > 5.63. The order of the proton conductivity of the crosslinked sulfonated polyimides at 90 °C was as follows: polyimide crosslinked with dibromo butane (0.070) > polyimide crosslinked with dibromo hexane (0.055) > polyimide crosslinked with dibromo decane (0.054). The crosslinked polyimides showed higher hydrolytic stability than the uncrosslinked polyimides. Between the crosslinked polyimides, the hydrolytic stability decreased with an increase in the alkyl chain length of the crosslinker. The crosslinked and uncrosslinked sulfonated polyimides exhibited almost the same proton conductivities. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2370–2379, 2005     

Synthesis and characterization of new soluble aromatic polyimides from diaminotetraphenylimidazolinone and aromatic tetracarboxylic dianhydrides

A series of new soluble aromatic polyimides with inherent viscosities of 0.65–1.12 dL/g were synthesized from 1,3-bis(4-aminophenyl)-4,5-diphenylimidazolin-2-one and various aromatic tetracarboxylic dianhydrides by the conventional two-step procedure that included ring-opening polyaddition and subsequent thermal cyclodehydration. These polyimides could also be prepared by the one-pot procedure in homogeneous m-cresol solution. Most of the tetraphenyl-pendant polyimides were soluble in organic solvents such as N,N-dimethylacetamide, 1,3-dimethyl-2-imidazolidone, and m-cresol. Some polyimides gave transparent, flexible, and tough films with good tensile properties. The glass transition temperatures and 10% weight loss temperatures under nitrogen of the polyimides were in the range of 287–326 and 520–580°C, respectively. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1767–1772, 1998     

Permselectivity and conductivity of membranes based on sulfonated naphthalenic copolyimides

A series of sulfonated diamines were synthesized which were further used to obtain relevant sulfonated naphthalenic copolyimides. Tough and ductile membranes were cast from solutions of the copolyimides in dimethylsulfoxide, which exhibit high ion-exchange capacity and high water uptake. The protonic conductivity of the membranes equilibrated with water lies in the range 1.0-8.6 S/m, at 25 degrees C, being of the same order of magnitude as that reported for perfluorinated acidic membranes. The values of the transport number of protons and sodium ions are close to the unit for very dilute electrolyte solutions, but they lie in the range 0.80-0.90 for moderate concentrations. The membranes exhibit rather high electroosmotic permeability. The similarity of the diffusion coefficients of protons and water in the membranes suggests that the Grottus mechanism governs the protonic conductive process in the acidic membranes equilibrated with water.     

Proton‐conductive membranes based on blends of polyimides

We prepared novel proton‐conductivity membranes based on blends of sulfonated polyimides. The blend membranes were prepared from a sulfonated homopolyimide and a sulfonated copolyimide with a solvent‐casting method. The proton conductivities of the blend membranes were measured as functions of the temperature with four‐point‐probe electrochemical impedance spectroscopy. The conductivity of the membranes strongly depended on the sulfonated homopolyimide content and increased with an increase in the content. The proton conductivity of all the blended membranes indicated a higher value than that determined in Nafion at 80 °C, and this may mean that the proton transfer in the blend membranes is responsible for the ionic channels induced by the hydrophobic and hydrophilic domains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1325–1332, 2007     

Synthesis and properties of novel sulfonated (co)polyimides bearing sulfonated aromatic pendant groups for PEFC applications

Novel sulfonated diamines bearing aromatic pendant groups, namely, 3,5‐diamino‐3′‐sulfo‐4′‐(4‐sulfophenoxy) benzophenone (DASSPB) and 3,5‐diamino‐3′‐sulfo‐4′‐(2,4‐disulfophenoxy) benzophenone (DASDSPB), were successfully synthesized. Novel side‐chain‐type sulfonated (co)polyimides (SPIs) were synthesized from these two diamines, 1,4,5,8‐naphthalene tetracarboxylic dianhydride (NTDA) and nonsulfonated diamines such as 4,4′‐bis(3‐aminophenoxy) phenyl sulfone (BAPPS). Tough and transparent membranes of SPIs with ion exchange capacity of 1.5–2.9 meq g^?1 were prepared. They showed good solubility and high thermal stability up to 300 °C. They showed isotropic membrane swelling in water, which was different from the main‐chain‐type and sulfoalkoxy‐based side‐chain‐type SPIs. The relative humidity (RH) and temperature dependence of proton conductivity were examined. At low RH, the novel SPI membranes showed much higher conductivity than the sulfoalkoxy‐based SPIs. They showed comparable or even higher proton conductivity than Nafion 112 in water at 60 °C (>0.10 S cm^?1). The membrane of NTDA‐DASDSPB/BAPPS (1/1)‐s displayed reasonably high proton conductivities of 0.05 and 0.30 S cm^?1 at 50 and 100% RH, respectively, at 120 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2862–2872, 2006     

燃料电池用磺化聚酰亚胺质子交换膜材料的制备与性质

以联萘二酐、磺化二胺和含咪唑基团的非磺化二胺单体为原料,制备了一系列高相对分子质量的磺化聚酰亚胺,该类聚合物具有优异的溶解性和良好的成膜性.得到的质子交换膜具有优异的水解稳定性.苯并咪唑碱性基团的存在提高了磺化聚酰亚胺质子交换膜膜的溶胀稳定性和热稳定性、降低了膜的甲醇透过率.质子导电率测试结果表明,IEC值为2.55mequiv·g-1的膜室温条件下的质子导电率为0.121 S·cm-1,高于在相同测试条件下Nafion 117膜的质子导电率(0.09 S·cm-1).     

Influence of carboxylated and phosphonated single-walled carbon nanotubes on the transport properties of sulfonated poly(styrene-isobutylene-styrene) membranes

This study discusses the effect of carboxylated (COOH) and phosphonated (PO₃H₂) single-walled carbon nanotubes (SWCNTs) on the transport properties of sulfonated poly(styrene-isobutylene-styrene) (SO₃H SIBS) as polymer nanocomposite membranes (PNMs) for direct methanol fuel cell (DMFC) and chemical and biological protective clothing (CBPC) applications. The properties were determined as a function of sulfonation level of SIBS, SWCNTs functionalization and loading. A comprehensive materials characterization study was performed to understand the interactions between the nanofillers and the functionalized polymer matrix, and to determine the effect of their incorporation on the resulting nanostructure of the PNMs. Results indicate that the sulfonation level is the variable that dictates nanofiller dispersion, mechanical properties, water absorption capabilities, morphology, and oxidative stability of SO₃H SIBS. Meanwhile, the nanofiller loading and functionalization influenced the transport properties. The nanofillers reduced methanol permeation. PO₃H₂ SWCNTs increased the proton conductivity but at a high sulfonation level (i.e., 90 mol %), the ionic interconnectivity caused a more complex morphology decreasing the transport of protons. Optimal selectivity in transport properties were found with a sulfonation level of 61 mol % and a PO₃H₂ SWCNTs loading of 1.0 wt. % for DMFC and 0.5 wt. % for CBPC due to changes in morphology and the unique transport mechanism of permeants through the PNMs. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2475–2495     

Synthesis and properties of aromatic polyureas from N,N′-bis(trimethylsilyl)-substituted aromatic diamines and aromatic diisocyanates

Silylated aromatic polyureas were synthesized by the polyaddition of N,N′-bis(trimethylsilyl)-substituted aromatic diamines to aromatic diisocyanates in various organic solvents at a temperature ranging from 30 to 100°C. Colorless and transparent films of the silylated polyureas were obtained by casting directly from these solutions in a dry nitrogen atmosphere. The silylated polyureas thermally decomposed at around 200°C and were easily desilylated with alcohol to convert to almost amorphous aromatic polyureas having inherent viscosities of 0.4–1.0 dL/g. The polyureas exhibited better solubility in organic solvents such as N,N-dimethylacetamide, N-methyl-2-pyrrolidone, and dimethyl sulfoxide and had somewhat lower thermal decomposition temperatures (around 300°C) than the polyureas prepared by a conventional method from the parent aromatic diamines and diisocyanates.     

Designing aromatic polyamides and polyimides for gas separation membranes

Aromatic polyamides and polyimides with improved gas permselectivity, can be designed and prepared by systematically changing structural elements that affect these properties. Indeed, a conscientious choosing of the chemical changes may still provide a promising approach to get better and better polymers for selective filtration of gases. The results of this work, in which novel monomers have been used, have confirmed that gas permeability through aromatic polyamides and polyimides much higher than that of conventional polyamides and polyimides can be achieved. It has been done by introducing bulky side groups, using non-planar monomers, and combining these elements on both monomers: diamines and dianhydrides or diamines and diacids. A theoretical study has also been made to explain the behaviour of some individual polymers, comparing experimental and calculated values of density and free volume.     

Preparation and properties of novel soluble aromatic polyimides from 4,4′-diaminotriphenylamine and aromatic tetracarboxylic dianhydrides

New aromatic polyimides containing triphenylamine unit were prepared by two different methods, i.e., a conventional two-step method starting from 4,4′-diaminotriphenylamine and aromatic tetracarboxylic dianhydrides and the one-step thioanhydride method starting from the aromatic diamine and aromatic tetracarboxylic dithioanhydrides. Both procedures yielded high-molecular-weight polyimides with inherent viscosities of 0.47–1.17 dL/g. Some of these polymers were soluble in organic solvents such as N,N-dimethylacetamide, N-methyl-2-pyrrolidone, m-cresol, and pyridine. All the polyimides afforded transparent, flexible, and tough films, and the color varied from pale yellow to dark red, depending markedly on the tetracarboxylic acid components. The glass transition temperatures (T_gs) of these polyimides were in the range of 287–331°C and the 10% weight loss temperatures were above 520°C in air. The polyimides prepared by the one-step method exhibited better solubility in organic solvents and had somewhat lower T_gs than the polymers prepared by a conventional two-step method.     

Chemically modified proton‐conducting membranes based on sulfonated polyimides: Improved water stability and fuel‐cell performance

A series of branched/crosslinked sulfonated polyimide (B/C‐SPI) membranes were prepared and evaluated as proton‐conducting ionomers based on the new concept of in situ crosslinking from sulfonated polyimide (SPI) oligomers and triamine monomers. Chemical branching and crosslinking in SPI oligomers with 1,3,5‐tris(4‐aminophenoxy)benzene as a crosslinker gave the polymer membranes very good water stability and mechanical properties under an accelerated aging treatment in water at 130 °C, despite their high ion‐exchange capacity (2.2–2.6 mequiv g^?1). The resulting polymer electrolytes displayed high proton conductivities of 0.2–0.3 S cm^?1 at 120 °C in water and reasonably high conductivities of 0.02–0.03 S cm^?1 at 50% relative humidity. In a single H₂/O₂ fuel‐cell system at 90 °C, they exhibited high fuel‐cell performances comparable to those of Nafion 112. The B/C‐SPI membranes also displayed good performances in a direct methanol fuel cell with methanol concentrations as high as 50 wt % that were superior to those of Nafion 112. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3751–3762, 2006     

Effects of diamine monomer structure on the gas permeability of polyimides. I. Bridged diamines

Permeability measurements for oxygen and nitrogen were carried out on a series of structurally similar polyimides in order to define structure/permeability relationships. The polyimides were prepared from 5,5′-[2,2,2-trifluoro-1-(trifluoromethyl) ethylidene] bis-1,3-isobenzofuranedione (6FDA) and a variety of substituted methylene dianilines and benzidines. A correlation between the diamine monomer structure and polymer permeability was found, particularly with diamine monomer variations at the ortho positions of the diamine relative to the amino moiety. These correlations were semilogarithmic, relative to the summation of the substituent volumes. Direct correlations were observed between the measured properties of polymer density and interchain d-spacings and the oxygen permeability value of each of these polyimides. In addition, we observed that the calculated values of fractional free volume were related to oxygen permeability in a manner which enabled us to identity a polar component in the effects of these ortho substituents. © 1993 John Wiley & Sons, Inc.     

Synthesis and characterization of organosoluble aliphatic-aromatic copolyimides based on cycloaliphatic dianhydride

A series of aliphatic-aromatic polyimides have been synthesized. These polyimides were prepared by high-temperature polycondensation of the aliphatic diamines: 1,4-diaminobutane, 1,6-diaminohexane, 1,7-diaminoheptane, 1,9-diaminononane, 1,10-diaminodecane, 1,12-diaminododecane and 4,4^′-methylenebis(2,6-dimethylaniline) with 1,2,3,4-cyclopentanetetracarboxylic dianhydride. Various ratios of diamines (aromatic:aliphatic) have been applied for preparation of copolyimides. Polycondensation proceeded at 190 °C and produced copolyimides with reduced viscosities up to 0.92 dl/g. The polyimides were soluble in a wide range of organic, common solvents and showed high-thermal stability. In most cases these polymers formed flexible films which presented excellent transparency.     

Synthesis and properties of novel polyimides from sulfonated binaphthalene dianhydride for proton exchange membranes

A sulfonated dianhydride monomer, 6,6′‐disulfonic‐4,4′‐binaphthyl‐1,1′,8,8′‐tetracarboxylic dianhydride (SBTDA), was successfully synthesized by direct sulfonation of the parent dianhydride, 4,4′‐binaphthyl‐1,1′,8,8′‐tetracarboxylic dianhydride (BTDA), using fuming sulfuric acid as the sulfonating reagent. A series of sulfonated homopolyimides were prepared from SBTDA and various common nonsulfonated diamines. The resulting polymer electrolytes, which contain ion conductivity sites on the deactivated positions of the aryl backbone rings, displayed high proton conductivities of 0.25–0.31 S cm^?1 at 80 °C. The oxidative stability test indicated that the attachment of the ? SO₃H groups onto the dianhydride units did not deteriorate the oxidative stability of the SPI membranes. The better membranes were achieved by the copolymerization of nonsulfonated diamine, SBTDA, and BTDA. Copolymer membrane synthesized from hexane‐1,6‐diamine, SBTDA, and BTDA displayed excellent water stability of more than 1000 h at 90 °C, while its proton conductivity was still at a high level (comparable to that of Nafion 117). Furthermore, the novel block copolymer ( II‐b ) displayed higher proton conductivity compared with the random one ( II‐r ) obviously, probably due to the slightly higher water uptake and better microphase separated morphology. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2820–2832, 2008     

Preparation and properties of new soluble aromatic polyimides from 2,2′-bis(3,4-dicarboxyphenoxy)biphenyl dianhydride and aromatic diamines

A new aromatic tetracarboxylic dianhydride having a crank and twisted noncoplannar structure, 2,2′-bis(3,4-dicarboxyphenoxy)biphenyl dianhydride, was synthesized by the reaction of 4-nitrophthalonitrile with biphenyl-2,2′-diol, followed by hydrolysis and cyclodehydration. The biphenyl-2,2′-diyl-containing aromatic polyimides having inherent viscosities up to 0.66 dL/g were obtained by the conventional two-step procedure starting from the dianhydride monomer and various aromatic diamines. Most of the polyimides were readily soluble in amide-type solvents such as N,N-dimethylacetamide and N-methyl-2-pyrrolidone. The aromatic polyimides had glass transition temperatures in the range of 205–242°C, and began to lose weight around 415°C, with 10% weight loss being recorded at about 500°C in air. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2021–2027, 1998