偏最小二乘法在多组分阳极溶出伏安分析中的应用—铜,锑,铋的同时测定

本文利用微分脉冲阳极溶出伏安法对微量铜、锑、铋混合溶液进行同进分析，实验在盐酸－氯化钠介质中进行，悬汞电极作工作电极，在－４００ｍＶ处富集电解５ｍｉｎ，然后由－４００ｍＶ向０Ｖ作微分脉冲溶出伏安扫描，扫描速度为２ｍＶ／ｓ，脉冲振幅为４０ｍＶ，由于计算机采集溶出伏安数据后采用偏最小二乘法计算并建立数学模型，然后据此模型对未知溶液进行定量分析，获得了较好的结果。     

同时测定癌症病人血液中锌镉铅铜的微分脉冲阳极溶出伏安法

用微分脉冲阳极溶出伏安法同时测定癌症病人血液中的锌、镉、铅和铜，以为癌症与这4种微量元素在血液中含量的相关性研究提供实验数据；癌症病人血液用硝酸-高氯酸消化，消化后的白色固体加水溶解，以0．100mol/L硫酸铵为底液，在三电极体系中进行测定，以峰电位定性，峰电流定量；用该法测定了3种癌症病人血液中的锌、镉、铅和铜，相对标准偏差为2．9％—3．3％(n＝6)，加标回收率为98％—110％；该法不用除氧、干扰少、分辨率好、准确度高，适用于临床血液中锌、镉、铅和铜的测定和研究。     

Uric Acid Determination by Adsorptive Stripping Voltammetry on Multiwall Carbon Nanotubes Based Screen‐Printed Electrodes

A sensitive electroanalytical methodology for the determination of uric acid in real samples using adsorptive voltammetry at a multiwalled carbon nanotubes (MWCNT) modified screen printed electrode (SPCE) is presented. Adsorption of uric acid takes place at open circuit potential at an optimized pH 5.0. Studies about the effect of accumulation time and scan rate on the analytical signal were developed and confirm the adsorption nature of the electrodic process. Quantitative analysis of uric acid by using its oxidation process at +0.18 V (vs. an Ag pseudoreference electrode) was carried out with an accumulation time of 5 min. Thus, a linear voltammetric based reproducible determination of uric acid (RSD 5 %) in the range 1–100 µM was obtained. The method was then successfully used for the determination of uric acid in real clinical samples of urine without detection of interferences. The proposed methodology only requires a dilution of the real sample and present advantages as low cost and easy handling for non specialized technicians.     

Simultaneous Determination of Cr(III) and Cr(VI) by Differential Pulse Voltammetry Using Modified Screen‐Printed Carbon Electrodes in Array Mode

A new procedure for the speciation of chromium by means of differential pulse voltammetry using screen‐printed carbon electrodes (SPCEs) has been proposed. Two different modified carbon working, a Ag/AgCl reference and a carbon counter screen‐printed electrodes have been connected in array mode for the simultaneous determination of Cr(III) and Cr(VI). Mercury films or gold nanoparticles have been ground onto the SPCEs in order to improve their selectivity to each chromium species. The quantification of the peak currents observed at ?1.25 V in Hg‐SPCE and ?0.1 V in AuNPs‐SPCE were carried out. The method has been applied to the speciation of chromium in waste water from a tannery factory.     

微分脉冲溶出伏安-偏最小二乘法同时测定代森锌和代森锰

采用循环伏安法讨论了两种常用的杀菌剂代森锰和代森锌在汞电极上的电化学还原反应机理,发现它们均具有良好的的伏安还原峰.采用微分脉冲溶出伏安法研究本体系时,获得的代森锰和代森锌的线性范围分别为0.005～0.07 mg/L和0.02～0.24 mg/L;检出限分别为4.10和12.8μg/L.由于这两种杀菌剂的分子结构很相似,它们的伏安波谱峰重叠严重,采用常规方法很难对它们分别进行测定.为解决波谱重叠的问题,本研究采用主成分回归和偏最小二乘法对波谱进行解析.结果表明,偏最小二乘法能得到较好的定量结果.利用本方法对几种蔬菜和水果样品进行分析,三氯甲烷作萃取剂的萃取率最大,回收率在95.5％～103％之间.     

铜膜差分脉冲阳极溶出伏安法测定药物中铋的含量

研究了铜膜电极代替汞膜电极测定重金属铋的差分脉冲溶出伏安法。实验了同位镀膜法测定铋的条件。在最佳实验条件下,Bi3+浓度在5×10-8~2×10-5mol/L范围内,其溶出峰峰高与浓度呈线性关系,检出限达到1×10-8mol/L。测定了一些药物中铋的含量,结果准确。     

Facile and Simultaneous Stripping Determination of Zinc,Cadmium and Lead on Disposable Multiwalled Carbon Nanotubes Modified Screen‐Printed Electrode

Screen‐printed electrodes (SPEs) are cheap and disposable. But their application for heavy metal detection is limited due to the low sensitivity and poor selectivity. Here we report the ultrasensitive and simultaneous determination of Zn²⁺, Cd²⁺ and Pb²⁺ on a multiwalled carbon nanotubes and Nafion composite modified SPE with in situ plated bismuth film (MWCNTs/NA/Bi/SPE). The linear curves range from 0.5–100 µg L^?1 for Zn²⁺ and 0.5–80 µg L^?1 for Cd²⁺. Uniquely, the linear curve for Pb²⁺ ranges from 0.05–100 µg L^?1 with a detection limit of 0.01 µg L^?1. The practical application was verified in real samples with satisfactory results.     

微分脉冲阳极溶出伏安法测定碘离子

基于I-能被氧化生成IO₃^-的特性,以铂球电极为工作电极,研究了微分脉冲阳极溶出伏安法(DPAS)测定碘离子.由于产物IO₃^-在电极上有吸附,因而在+1.3V电清洗120s.在pH=4的0.1mol/LKH₂PO₄-K₂HPO₄缓冲溶液底液中,能检测出5.00×10^-7mol/L的I-,在5.00×10^-71.50×10^-5mol/L范围内I^-的浓度与峰电流有良好的线性关系.该方法用于海带、食用碘盐中碘的测定,取得了较好的结果.     

示差脉冲阳极溶出伏安法测定莲子芯中微量铅

采用自制丝网印刷微电极,结合阳极溶出法对微波消解后的莲子芯中的微量铅进行了测定.考察了微波消解条件、缓冲溶液pH值、富集电位、富集时间、脉冲强度、脉冲周期等对检测的影响.试验结果表明:在pH 3.6的乙酸-乙酸钠缓冲溶液中,-1.1 V富集10 s后,电流与铅的质量浓度在1～1 000μg·L-1范围内呈线性关系,相关系数为0.996.测定结果的相对标准偏差(n=5)小于5%,加标回收率为101.9%.     

The Electrochemical Behavior of Nitrazepam at a Screen‐Printed Carbon Electrode and Its Determination in Beverages by Adsorptive Stripping Voltammetry

The cyclic voltammetric behavior of nitrazepam was investigated at screen‐printed carbon electrodes over the range ?1.5 V to +1.5 V. Two reduction peaks were observable on the negative scan, at ?0.7 V, and ?1.2 V using pH 6 buffer. On the return scan a single oxidation peak was obtained at ?0.05 V. For quantitative analysis of beverages, we developed an anodic adsorptive stripping voltammetric method which required only dilution with buffer. The identification of nitrazepam and flunitrazepam could be achieved using cyclic voltammetry.     

Ultrasensitive Determination of Vitamin B12 Using Disposable Graphite Screen‐Printed Electrodes and Anodic Adsorptive Voltammetry

A facile, rapid and ultra‐sensitive method for the determination of vitamin B₁₂ (cyanocobalamin) at the sub‐nanomolar concentration range by using low‐cost, disposable graphite screen‐printed electrodes is described. The method is based on the cathodic preconcentration of square planar vitamin B_12s, as occurred due to the electro reduction of Co(III) center in vitamin B_12a to Co(I), at ?1.3 V versus Ag/AgCl/3 M KCl for 40 s. Then, an anodic square wave scan was applied and the height of the peak appeared at ca. ?0.73 V versus Ag/AgCl/3 M KCl, due to the oxidation of Co(I) to Co(II) in the adsorbed molecule, was related to the concentration of the vitamin B₁₂ in the sample. EDTA was found to serve as a key‐component of the electrolyte by eliminating the background signal caused by metal cations impurities contained in the electrolyte (0.1 M phosphate buffer in 0.1 M KCl, pH 3). It also blocks trace metals contained in real samples, thus eliminating their interference effect. The method was optimized to various working parameters and under the selected conditions the calibration curve was linear over the range 1×10^?10–8×10^?9 mol L^?1 vitamin B₁₂ (R²=0.994), while the limit of detection for a signal‐to‐noise ratio of 3 (7×10^?11 mol L^?1 vitamin B₁₂) is the lowest value of any reported in the literature for the electrochemical determination of vitamin B₁₂. The sensors were successfully applied to the determination of vitamin B₁₂ in pharmaceutical products.     

Lead Determination by Anodic Stripping Voltammetry Using a p‐Phenylenediamine Modified Carbon Paste Electrode

Carbon paste electrodes were modified by mixing appropriate amounts of the monomers o‐phenylendiamine, p‐phenylendiamine and m‐phenylendiamine (o‐PD, p‐PD and m‐PD) into a graphite powder‐paraffin oil matrix. The electropolymerization of the incorporated phenylendiamine was then carried out in a carbon paste electrode in acidic medium by cyclic voltammetry between ?0.30 V and +0.90 or under constant potential. The modified carbon paste electrodes (MCPEs) obtained by this electropolymerization method were found to be useful for trace determination of Pb²⁺ in aqueous solutions. Lead(II) was first preconcentrated on the modified electrodes by complexation with the modifier, and the electrode was then transferred to an electrochemical cell. The best results in terms of sensitivity and detection limit were obtained with poly p‐phenylenediamine (poly (p‐PD)). For a 10‐min preconcentration time, the calibration plot was linear from 5×10^?8 mol L^?1 to 10^?5 mol L^?1, with r²=0.999 and relative standard deviation equal to 5%. However, the lowest lead concentration that could be detected was 10^?9 mol L^?1. Interference from metal ions like Cd(II), Hg(II), Zn(II), Fe(II) and Cu(II) was also studied.     

Simultaneous Determination of Cadmium,Lead, Copper,and Thallium in Highly Saline Samples by Anodic Stripping Voltammetry (ASV) Using Mercury‐Film and Bismuth‐Film Electrodes

This paper describes a comparative study of the simultaneous determination of Cd(II), Pb(II), Tl(I), and Cu(II) in highly saline samples (seawater, hydrothermal fluids, and dialysis concentrates) by ASV using the mercury‐film electrode (MFE) and the bismuth‐film electrode (BiFE) as working electrodes. The features of MFE and BiFE as working electrodes for the single‐run ASV determinations are shown and their performances are compared with that of HMDE under similar conditions. It was observed that the stripping peak of Tl(I) was well separated from Cd(II) and Pb(II) peaks in all the studied saline samples when MFE was used. Because of the severe overlapping of Bi(III) and Cu(II) stripping peaks in the ASV using BiFE, as well as the overlapping of Pb(II) and Tl(I) stripping peaks in the ASV using HMDE, the simultaneous determination of these metals was not possible in highly saline medium using these both working electrodes. The detection limits calculated for the metals using MFE and BiFE (deposition time of 60 s) were between 0.043 and 0.070 μg L^?1 for Cd(II), between 0.060 and 0.10 μg L^?1 for Pb(II) and between 0.70 and 8.12 μg L^?1 for Tl(I) in the saline samples studied. The detection limits calculated for Cu(II) using the MFE were 0.15 and 0.50 μg L^?1 in seawater/hydrothermal fluid and dialysis concentrate samples, respectively. The methods were applied to the simultaneous determination of Cd(II), Pb(II), Tl(I), and Cu(II) in samples of seawater, hydrothermal fluids and dialysis concentrates.     

微分脉冲溶出伏安法结合化学计量学测定醚类除草剂

在pH=6.82的Britton-Robinson缓冲溶液中,采用循环伏安法和微分脉冲溶出伏安法对醚类除草剂甲羧除草醚(Bifenox)和三氟羧草醚(Acifluofen)的伏安行为进行了研究,发现吸附时间为50 s时此电化学体系达到平衡,而且微分脉冲溶出伏安法能给出较高的灵敏度,甲羧除草醚和三氟羧草醚分别在-685 mV和-700 mV处具有良好还原峰,但由于峰电位接近而谱峰重叠,很难分别测定.本文采用化学计量学方法来解析重叠峰并完成这两种除草剂的定量分析.甲羧除草醚和三氟羧草醚的测定线性范围分别为0.02～0.18 μg·5mL~(-1)和0.02～0.16 μg·5mL~(-1),检出限分别为0.0073 μg·5mL~(-1)和0.0068 μg·5mL~(-1).利用该方法对水样中的甲羧除草醚和三氟羧草醚进行直接测定,获得了较好的定量分析结果.     

流通电解池-连续介质交换差示脉冲阳极溶出伏安法同时测定镉、铟

本文采用自制流通电解池,在盐酸溶液中富集Cd(Ⅱ),In(Ⅲ),经连续介质交换,在选定的乙二胺-氯化钠溶液中进行差示脉冲阳极溶出。得到的镉、铟溶出峰△Ep≥100mV。波形完好。从根本上解决了盐酸溶液中Cd(Ⅱ)、In(Ⅲ)的阳极溶出峰相重叠的问题。建立了一个灵敏、快速,同时测定镉、铟的分析方法。     

Sensitive Stripping Determination of Cadmium(II) and Lead(II) on Disposable Graphene Modified Screen‐Printed Electrode

In the present work, a sensitive, facile and disposable sensing platform for trace analysis of heavy metal ions was developed at the Bi modified graphene‐poly(sodium 4‐styrenesulfonate) composite film screen printed electrode (GR/PSS/Bi/SPE). The GR/PSS/Bi/SPE improved sensitivity and linearity due to the functionalization of graphene with negatively charged PSS providing more absorbing sites. The detection limit of the GR/PSS/Bi/SPE is found to be 0.042 µg L^?1 for Cd²⁺ and 0.089 µg L^?1 for Pb²⁺ with linear responses of Cd²⁺ and Pb²⁺ in the range of 0.5–120 µg L^?1. Finally, the practical application was confirmed in real water with satisfactory results.     

Differential Pulse Voltammetric Determination of Local Anesthetics Heptacaine,Carbisocaine and Pentacaine at DNA Modified Screen‐Printed Electrode

A procedure for the differential pulse voltammetric determination of three local anesthetics (Heptacaine, Carbisocaine and Pentacaine) at a screen‐printed electrode surface modified with the dsDNA layer is described. The detection limits obtained after 120 s drug accumulation from 0.01 M phosphate buffer solution pH 6.96 are 0.02 μM (Pentacaine) and 0.03 μM (Carbisocaine and Heptacaine). The method was applied to the determination of Carbisocaine in spiked serum.     

Simultaneous Determination of Cadmium,Copper, Lead and Zinc in Amino Acid Parenteral Nutrition Solutions by Anodic Stripping Voltammetry and Sample Digestion by UV Irradiation

Abstract

Irradiation with ultraviolet (UV) energy was investigated to assay cadmium, copper, lead, and zinc by anodic stripping voltammetry (ASV) in amino acid parenteral nutrition (PN) solutions. Sample digestion by UV irradiation showed the best performances to liberate the metals from the samples (metal recoveries between 90% and 102%) in comparison with classical oxidative wet digestion methods. The best UV digestion condition was obtained with 1:10 diluted PN samples irradiated during 10 h at 90±3°C with the addition of one aliquot of 50 µL concentrated H₂SO₄ and repeated additions of 50 µL 30% (v/v) H₂O₂ at each 60 min irradiation interval. By using the UV digestion procedure cadmium, copper, lead, and zinc were simultaneously assayed in commercial amino acid PN solutions by ASV. The metal concentrations ranged between 1.3 to 4.4 for cadmium, 2.9 to 40.8 for copper, 4.4 to 16.8 for lead, and 1.4 to 208.5 for zinc. The ASV method correlated well with atomic absorption spectrometry measurements to assay the investigated analytes in amino acid PN samples after the UV digestion.     

Voltammetric Determination of Neonicotinoid Pesticides at Disposable Screen‐Printed Sensors Featuring a Sputtered Bismuth Electrode

This work reports the determination of 5 neonicotinoid pesticides (Clothianidin, Imidacloprid, Thiamethoxam, Nitenpyram and Dinotefuran) in water samples by cathodic differential pulse (DP) voltammetry at screen‐printed disposable sensors featuring a sputtered bismuth thick‐film working electrode, a Ag reference electrode and a carbon counter electrode. The performance of the bismuth thick‐film electrodes was compared to that of a home‐made bismuth thin‐film electrode and a bismuth‐bulk electrode. The electrodes were further characterized by electrochemical and optical techniques. The effect of the pH of the supporting electrolyte on the DP reduction currents of the 5 pesticides was studied. The limits of quantification (LOQs) in 4 water matrices (distilled water, tap water, mineral water and surface water) were in the range 0.76 to 2.10 mg L^?1 but severe matrix effects were observed in the analysis of mineral and, especially, surface water samples. Using a solid‐phase extraction (SPE) procedure using Lichrolut EN cartridges and elution with methanol, the matrix effects were substantially reduced and the LOQs were in the range 9 to 17 µg L^?1_. The recoveries of surface water samples spiked with the 5 target neonicotinoids at two concentration levels (20 and 50 µg L^?1) were in the range 89 to 109 % and the % relative standard deviations ranged from 4.3 to 7.2 %.     

差分脉冲溶出伏安法测定陶瓷器皿中铅和镉的溶出率

采用4%的乙酸浸泡陶瓷样品24 h,应用同位镀汞差分脉冲溶出伏安法测定了陶瓷样品中微量重金属铅、镉的溶出量。以0.1 mol/L的硝酸溶液做底液,0.1 mol/L的KCl溶液做支持电解质,2 g/L的Hg2+溶液做镀汞液,测得铅的溶出峰电位为-0.5 V(vsSCE),镉的溶出峰电位为-0.7 V(vsSCE),两者含量在5×10-4～1 mg/L和5×10-4～0.5 mg/L范围内峰电流和其含量呈良好的线性关系,检出限分别为2×10-4和4.3×10-3mg/L。