A Novel Bioelectrochemical Sensor Based on Immobilized Urease on the Surface of Nickel Oxide Nanoparticle and Polypyrrole Composite Modified Pt Electrode

Nickel oxide nanoparticle (NiO?NP) and polypyrrole (PPy) composite were deposited on a Pt electrode for fabrication of a urea biosensor. To develop the sensor, a thin film of PPy?NiO composite was deposited on a Pt substrate that serves as a matrix for the immobilization of enzyme. Urease was immobilized on the surface of Pt/PPy?NiO by a physical adsorption. The response of the fabricated electrode (Pt/PPy?NiO/Urs) towards urea was analyzed by chronoamperometry and cyclic voltammetry (CV) techniques. Electrochemical response of the bio‐electrode was significantly enhanced. This is due to electron transfer between Ni²⁺ and Ni³⁺ as the electro‐catalytic group and the reaction between polypyrrole and the urease‐liberated ammonium. The fabricated electrode showed reliable and demonstrated perfectly linear response (0.7–26.7 mM of urea concentration, R²= 0.993), with high sensitivity (0.153 mA mM^?1 cm^?2), low detection of limit (1.6 μM), long stability (10 weeks), and low response time (～5 s). The developed biosensor was highly selective and obtained data were repeatable and reproduced using PPy‐NiO composite loaded with immobilized urease as urea biosensors.     

Nanocomposite with Polypyrrole Encapsulated within SBA‐15 Mesoporous Silica: Preparation and Its Electrochemical Application

The nanocomposite with polypyrrole (PPy) confined in ordered mesoporous silica SBA‐15 channels was synthesized by in situ electropolymerization. X‐ray diffraction, scanning electron microscopy, transmission electron microscopy, N₂ adsorption/desorption, and FT‐IR studies indicated that the nanocomposite has the well‐ordered hexagonal structures and PPy was in situ polymerized into the channels instead of the outer surface of SBA‐15. Furthermore, the PPy/SBA‐15 nanocomposite was used as an electrode modifier. We found that the nanocomposite‐modified electrode exhibited good electrocatalytic activities for hydroquinone oxidation where PPy chains could facilitate the electron transfer between molecular sieves and electrode surface. Three dihydroxybenzene isomers (hydroquinone, catechol and resorcinol) have been successfully detected at PPy/SBA‐15 modified electrode by preconcentration of the analyte.     

Synthesis and characterization of polypyrrole nanofibers with different dopants

Nanostructures of polypyrrole (PPy) were synthesized in the presence of different dopants including hydrochloric acid (HCl), ferric chloride (FeCl₃), p‐toluene sulfonic acid (p‐TSA), camphor sulfonic acid (CSA), and polystyrene sulfonic acid (PSSA), using a simple interfacial oxidative polymerization method. The method is a reliable non‐template approach with relatively simple instrumentation, ease of synthesis, and economic viability for synthesizing PPy nanostructures. Morphology of synthesized PPy structures was investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM), which indicate the formation of one‐dimensional (1D) nanofibers with average diameter of 75–180 nm. Energy dispersive spectrum (EDS) of the PPy nanofibers indicates the attachment of the dopants to the PPy backbone; the fact is further confirmed by the Fourier transform infrared (FTIR) spectra of PPy nanostructures. Thermal stabilities of the nanostructures explored using thermal gravimetric analysis (TGA) follow the order PPy‐p‐TSA > CSA > HCl > FeCl₃ > PSSA. It is noticed that the electrical conductivity (EC) of PPy nanostructures depends upon the nature of dopant (PPy‐p‐TSA > CSA > HCl > FeCl₃ > PSSA), PPy‐p‐TSA nanofibers showing the highest EC of 6 × 10^?2 Scm^?1. Copyright © 2009 John Wiley & Sons, Ltd.     

Electrochemical preparation of effective and low cost catalyst for electrooxidation of ethanol

A nanocatalyst coating was prepared at surface of a glassy carbon electrode by electropolymerization of pyrrole by cycling the electrode potential between ?0.8 and 0.8 V (vs. Ag/AgCl). Then, polypyrrole film was potentiostatically coated with platinum nanoparticles at constant potential of ?0.2 V (vs. Ag/AgCl). The resulting electrode was denoted as GCE/PPy/Pt. This modified electrode was characterized by IR, SEM, TEM and EDX. The electrocatalytic oxidation of ethanol at the GCE/PPy/Pt has been investigated using cyclic voltammetric and chronoamperometric methods. The effects of various parameters on electrocatalytic oxidation of the ethanol, such as the thickness of PPy film, the amount of platinum nanoparticles, ethanol concentration, potential scan rate and working potential limit in anodic direction, were investigated. The kinetic of the ethanol oxidation is discussed on the GCE/PPy/Pt. The stability and reproducibility of this modified electrode were also studied.     

Preparation and Properties of Composite Polypyrrole/Pt Catalyst Systems

Three different methods for the preparation and modification of conducting polymer/noble metal catalyst systems consisting of polypyrrole (PPy) and platinum (Pt) are described for the anodic oxidation of methanol. The first method consists of the electrochemical deposition of a thin PPy film on glassy carbon substrate, which is modified with Pt either by electroreduction of hexachloroplatinate, codeposition from a nanodispersed Pt solution, or incorporation of tetrachloroplatinate as counterion followed by cathodic reduction. A second method is based on the preparation of nanoscale PPy(PSS) particles by chemical polymerization with polystyrenesulfonate PSS^– as the counterion. This material is a favorable catalyst support for nanodispersed Pt due to its mixed electronic and cationic conductivity. To study the electrochemical properties, the particulate system PPy(PSS)/Pt is fixed in a carbon fiber electrode. A third method was developed which brings the polypyrrole in close contact to a proton exchanger membrane (Nafion) using a special chemical deposition procedure. This method is useful for preparing a membrane electrode assembly (MEA) consisting of Nafion/PPy/Pt. The structural, morphological, and electrocatalytic properties for methanol oxidation were studied depending on the preparation method applied using surface analytical techniques (TEM, SEM, and EDX) and electrochemical measurements (cyclic voltammetry and transient techniques).     

Nanocomposite of Platinum Particles Embedded into Nanosheets of Polycarbazole for Methanol Oxidation

Nanoparticles of Pt were successfully electrodeposited onto polycarbazole (PCz) film on a stainless steel (SS‐PCz‐Pt) by chronocoulometry (0.2 C). For comparative purposes, Pt particles were deposited into stainless steel (SS‐Pt) under the same condition. Fourier transform infrared spectroscopy (FT‐IR) results confirmed PCz exists in the SS‐PCz‐Pt composite electrode. X‐ray photoelectron spectroscopy (XPS) results indicated that PCz of SS‐PCz can interact easily with Pt particles. The crystalline behavior and morphology of SS‐PCz‐Pt and SS‐Pt were determined by X‐ray diffraction (XRD) analysis, scanning electron microscopy (SEM), and Transmission Electron Microscopy (TEM). The TEM results indicated that Pt particles disperse more uniformly into the nanosheets of polycarbazole than those of SS film. Catalytic activity and stability for the oxidation of methanol were studied by using cyclic voltammetry and chronoamperometry. A high catalytic current for methanol oxidation (8.04 mA cm^?2 mg^?1) was found for the SS‐PCz‐Pt electrode in comparison to SS‐Pt electrode (5.01 mA cm^?2 mg^?1) at about 0.6 V (vs. Ag/AgCl).     

Electrochemical Sensor for Oxidation of NO Based on Au-Pt Nanoparticles Self-assembly Film

Au-Pt bimetallic nanoparticles film used as an efficient electrochemical sensor was prepared by self-assembled Au-Pt bimetallic nanoparticles on a glassy carbon (GC) substrate using thioglycolic acid as a linker. Atomic force microscopy (AFM) and scanning electron microscopy (SEM) showed that the Au-Pt nanoparticles self-assembly film was dense and uniform. Electrochemical experiments revealed that Au-Pt bimetallic nanoparticles film/GC electrode showed high electrocatalytic activity to the oxidation of nitric oxide.     

离子液体中吡咯的电化学聚合及性质研究

以1-丁基-3-甲基咪唑六氟磷酸盐离子液体作为溶剂和支持电解质,分别在铂电极和导电玻璃电极上电化学聚合得到了聚吡咯,聚合过程中发现,在离子液体中聚合的循环伏安图,其电流的变化和传统有机溶剂中的不同,通过交流阻抗技术研究了修饰电极的电化学性质,采用在线紫外、拉曼、红外谱对聚吡咯进行了光谱表征,得到了聚吡咯的特征峰,采用扫描电镜研究了聚合物的形貌。最后将修饰电极应用到了对对苯二酚的催化反应当中,显示了一定的催化作用。     

Application of Al2O3 in the electrosynthesis of polypyrrole with fuzzy morphology—Microtentacle

Polypyrrole (PPy) thin films were electrochemically polymerized onto the electrode surface. In this study alumina was used as the template and PPy film was prepared by electrochemical polymerization using Al/Al₂O₃ as the working electrode. Surface morphology of PPy was investigated by scanning electron microscopy (SEM) and the results revealed that the application of the template resulted in PPy with fantastic surface morphology which was called microtentacle and the length of the tentacle could reach 15 µm. The morphology can evidently increase the roughness, thus the surface area of the electrode substrate, and provide an intimate contact with the surrounding brain tissue compared to the hard, stiff metal surface. Relationship between PPy morphology and electrochemical polymerization parameters, such as polymerization time, was investigated. The study provided a fundamental method to prepare a PPy‐modified electrode with high surface area. Potential application of the study is proposed. Copyright © 2007 John Wiley & Sons, Ltd.     

A comparison of redox processes for polypyrrole/dodecylsulfate films in aqueous and non-aqueous media

Polypyrrole/dodecylsulfate (PPy/DDS) films were synthesized in aqueous and ethanolic solutions and investigated in aqueous, ethanolic, methanolic and acetonitrile solutions by cyclic voltammetry (CV). The amounts of anions and cations in the films before and after electrochemical treatment were determined by electron probe microanalysis (EPMA); the film morphology was studied by scanning electron microscopy (SEM). The results prove that the mobility of bulky DDS^– ions in PPy increases in the order: water<acetonitrile<ethanol<methanol. It was found that dopant DDS^– ions can be easily removed from PPy matrix swollen in alcohols or acetonitrile by electrochemical reduction or by soaking in electrolyte solutions of these solvents. The influence of electrochemical treatment on the change of doping level in aqueous solution is essentially less and depends on the cations in the test solution. Although the electroneutrality of PPy/DDS films during redox cycling is realized mainly by movement of the cations in aqueous solution and by movement of the anions in organic solvents, nevertheless the participation of anions in aqueous and cations in organic solvents is also established. The redox properties of PPy/DDS are more dependent on the solvent of the test solutions than of the synthesis solutions. Electronic Publication     

Coupling of a Reagentless Electrochemical DNA Biosensor with Conducting Polymer Film and Nanocomposite as Matrices for the Detection of the HIV DNA Sequences

Abstract

This paper describes a reagentless electrochemical DNA biosensor applied to the detection of human immunodeficiency virus (HIV) sequences based on electrochemical impedance spectroscopy (EIS). The novel DNA biosensor has been elaborated by means of an opposite‐charged adsorption Au‐Ag nanocomposite to a conductive polymer polypyrrole (PPy) modified platinum electrode (Pt) and self‐assembly the mercapto oligonucleotide probes onto the surface of modified electrode via the nanocomposite. The duplex formation was detected by measuring the electrochemical impedance signal of nucleic acids in phosphate buffer solution (PBS). Such response is based on the concomitant conductivity changes of the PPy film and nanocomposite. The reagentless scheme has been characterised using 21‐mer synthetic oligonucleotides as models: parameters affecting the hybridization assay were explored and optimized. The detection limit is 5.0×10^?10 M of target oligonucleotides at 3σ. The potential for development of reagentless DNA hybridization analysis in the clinical diagnosis is being pursued.     

Microdimensional Polyaniline: Fabrication and Characterization of Dynamics of Charge Propagation at Microdisk Electrodes

We describe fabrication of microdimensional polyanilne films in a controlled manner by voltammetric potential cycling or controlled potential electrolysis on platinum microdisk electrodes. The film grows in a form of hemispherical microdeposits, and its size largely exceeds the size of a Pt microdisk. Consequently, the film covers both the Pt substrate as well as the surrounding glass seal. Since the adhering polyaniline layer is conducting, the latter situation may lead to an increase in the effective electrode surface area. The lateral growth of polyaniline films outside the microdisk has also been demonstrated by performing diagnostic voltammetric experiments with use of a double microdisk set‐up in which independent polarization of each disk is feasible. Microelectrode‐based chronocoulometry, that involves an uncomplicated well‐defined reduction potential step starting from the emeraldine (conducting) form and ending at leucoemeraldine (nonconducting) form, yields (upon application of a sufficiently short pulse) a well‐defined linear response of charge versus square root of time that is consistent with the linear effective diffusion as the predominant charge propagation mechanism. When describing the system kinetics in terms of the effective (apparent) diffusion coefficient, we expect this parameter to be on the level of 10^?8 cm² s^?1 or lower. The relative changes in dynamics of charge transport are discussed with respect to the polyaniline film loading, the size of microdisk electrode, expansion of the active electrode area, and the choice of electrolyte (strong acid) anion. The results are consistent with the view that when Pt microelectrode is modified with PANI deposit exceeding the size of the microdisk substrate, it behaves in a way as if its surface area is effectively much larger than the geometric area of Pt microdisk.     

A Sensitive and Selective Nitrite Detection in Water Using Graphene/Platinum Nanocomposite

A glassy carbon electrode modified with reduced graphene oxide and platinum nanocomposite film was developed simply by electrochemical method for the sensitive and selective detection of nitrite in water. The electrochemical reduction of graphene oxide (GO) efficiently eliminates oxygen‐containing functional groups. Pt nanoparticles were electrochemically and homogeneously deposited on the ErGO surface. Field emission scanning electron microscopy (FE‐SEM), Raman spectroscopy, attenuated total reflectance‐fourier transform infrared spectroscopy (ATR‐FTIR), electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV) were used to examine the surface morphology and electrocatalytic properties of the Pt‐ErGO nanocomposite film‐modified electrode surface. The fabricated nitrite sensor showed good electrochemical performance with two linear ranges; one from 5 to 100 µM (R²=0.9995) and the other from 100 to 1000 µM (R²=0.9972) and a detection limit of 0.22 µM. The proposed sensor was successfully applied for the detection of nitrite in tap water samples which proves performance of the Pt‐ErGO nanocomposite films.     

ELECTRICALLY CONDUCTIVE COMPOSITE PREPARED BY ELECTROCHEMICAL POLYMERIZATION OF PYRROLE IN POLY-(p- PHENYLENE TEREPHTHALAMIDE) MATRIX

The preparation of PPy/PPTA conductive composite films by electrochemical method is presented.The first step is to cast a thin layer of poly (p-phenylene-terephthalamide) (PPTA) on a slice of Pt working electrode. The second step is to electrochemically polymerize pyrrole on the PPTA/Pt working electrode. Both of the electrical conductivity and the mechanical properties of the PPy/PPTA composite film are better than those of the pure PPy film, and the film has excellent flexibility at low temperature, even in liquid nitrogen.The SEM picture of the cross-section of PPy,/PPTA composite film showed that the two components were well mixed.Cyclic voltammograms of PPy,/PPTA film in aqueous solution showed that the conductive films could be reduced and reoxidized.     

抗坏血酸在PPy-HEImTfa/Pt电极上的电催化氧化及其机理

以铂为基底电极,在1-乙基咪唑三氟乙酸盐(HEImTfa)离子液体中电化学合成导电聚吡咯(PPy),制得PPy-HEImTfa/Pt电极;采用循环伏安法研究了PPy-HEImTfa/Pt电极对抗坏血酸的电催化氧化性能.结果表明:PPy-HEImTfa/Pt电极对0.1mo·lL-1抗坏血酸具有较高的电催化氧化活性,与相同条件下硫酸溶液中在铂表面修饰的聚吡咯(PPy-H2SO4/Pt)电极和裸铂电极相比,其氧化峰电位分别降低了0.10和0.19V,氧化峰电流分别增加了3.0和3.6mA.同时采用原位傅里叶变换红外(insitu FTIR)光谱技术对抗坏血酸在PPy-HEImTfa/Pt电极上的电氧化机理进行了研究,结果表明:抗坏血酸在PPy-HEImTfa/Pt电极上首先被氧化为脱氢抗坏血酸,在水溶液中脱氢抗坏血酸迅速发生水合作用形成水合脱氢抗坏血酸,它进一步水解并发生内酯开环反应生成2,3-二酮古洛糖酸;在较高电位下,部分抗坏血酸最终被氧化成CO2.     

Preparation,Electrochemistry, and Electrocatalytic Activity of Lead Pentacyanonitrosylferrate Film Immobilized on Carbon Ceramic Electrode

Lead pentacyanonitrosylferrate (PbPCNF), a new Prussian blue analog, was immobilized on the surface of a carbon ceramic electrode (CCE) prepared by sol‐gel method. The immobilization process consists of adding a certain amount of metallic lead to the electrode matrix before gelation, and chemical derivatization of Pb on the electrode surface to a PbPCNF solid film by immersing the electrode in a solution of sodium pentacyanonitrosylferrate (PCNF). The composition of the synthesized PbPCNF was characterized by FTIR, scanning electron microscopy (SEM), and energy‐dispersive X‐ray (EDX) techniques. The resulting modified electrode showed electroactivity at two redox centers. The electrochemical behavior of the PbPCNF modified carbon ceramic electrode (PbPCNF|CCE) was studied by cyclic voltammetry. Under optimized conditions the peak‐to‐peak separation is only 39 mV, indicative of a surface reaction. Ion effects of the supporting electrolyte suggest that cations have a considerable effect on the electrochemical behavior of the modified electrode. The transfer coefficient (α) and the charge transfer rate constant at the modifying film|electrode interface (k_s) were calculated. The electrocatalytic activity of the modified electrode toward the electro‐reduction of peroxodisulfate was studied in details.     

In situ analytical electron microscopy studies of redox reactions at a YSZ/Pt interface

Redox reactions were studied at a single yttria-stabilized zirconia (YSZ)/Pt electrode interface, in parallel with pure YSZ with no catalyst electrode, by in situ analytical electron microscopy at elevated temperatures and in an oxygen atmosphere. In situ electron holography showed that the oxide underwent reduction at elevated temperatures in a vacuum and was consequently reoxidized upon exposure to an oxygen flux at the same temperature. In situ energy loss spectroscopy measurements were in agreement with in situ electron holography observations and indicated that the oxidation state of the host cation zirconium was altered in the reduced state of the YSZ to the metastable state Zr(3+).     

Electrochemical Deposition of Gold Metal Particles into 3‐Dimensional Polypyrrole Film Deposited on a Highly Oriented Pyrolytic Graphite

Electrochemical techniques and lateral friction microscopy (LFM) are exploited to characterize the deposition of gold metal particles onto the 3‐dimensional (3‐D) polypyrrole (PPy) film deposited on 2‐dimensional (2‐D) highly oriented pyrolytic graphite (HOPG) substrate surface in an aqueous solution involving 0.01 M pyrrole and 0.1 M LiClO₄? 3H₂O. Cyclic voltammetry is utilized to find the gold deposition potential onto the PPy film from 0.001 M KAu(CN)₂/KOH solution. The gold deposition potential is found to be in the range of ?1.2 V to ?1.4 V. Chronoamperometry is used to find out the nucleation and growth mechanism of gold metal particles onto PPy film. When the PPy film is thin, the mechanism follows the 3‐D instantaneous and moved towards 3‐D progressive as the film thickness increases. Considering the high resistance of thick PPy film and insulating and compact nature of the film at more cathodic potentials, it is suggested that the gold nuclei are formed first on the HOPG substrate surface, move to the PPy film surface and then distributed inside the PPy matrix. Since the friction of gold and the PPy film is different, the LFM is found to be an effective tool to see the distribution of gold particles in the domain boundaries of the PPy film.     

Facilely prepared polypyrrole-graphene oxide-sodium dodecylbenzene sulfonate nanocomposites by in situ emulsion polymerization for high-performance supercapacitor electrodes

The layered polypyrrole-graphene oxide-sodium dodecylbenzene sulfonate (PPyGO-SDBS) nanocomposites were facilely fabricated via an in situ emulsion polymerization method with the assistance of SDBS as dopant and stabilizer. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and electrochemical performance were employed to analyze the structure and the characteristics of the composites. The results showed that SDBS played an important role in improving the electrochemical performance of the PPyGO-SDBS, by dispersing the PPy between the layers of the GO. The obtained PPyGO-SDBS exhibited remarkable performance as an electrode material for supercapacitors, with a specific capacitance as high as 483 F g^?1 at a current density of 0.2 A g^?1 when the mass ratio of pyrrole to GO was 80:20. The attenuation of the specific capacitance was less than 20 % after 1,000 charge–discharge processes, supporting the idea that PPy inserted successfully into the GO interlayers. The excellent electrochemical performance seemed to arise from the synergistic effect between the PPy and the GO and the dispersion of the PPy induced by SDBS.     

Synthesis of a hexafluoropropylidene-bis(phthalic anhydride)-based polyimide and its conducting polymer composites with polypyrrole

A new electrically conducting composite film from polypyrrole and 4,4′-(hexafluoroisopropylidene)-bis(phthalic anhydride)-based polyimide was prepared. Pyrrole and the dopant ion can easily penetrate through the polyimide substrate and electropolymerize on the platinum (Pt) electrode due to the swelling of the polyimide on the metal electrode. The electrochemical properties of polypyrrole-polyimide (PPy/PI) composite films have been investigated by using cyclic voltammetry. The PPy/PI composite film is suitable for use as the electroactive material owing to its stable and controllable electrochemical properties. The electrical conductivity of composites falls in the range 0.0035–15 S/cm. Scanning electron micrograph, FTIR, and thermal studies indicate that PPy and PI form a homogeneous material rather than a simple mixture. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3009–3016, 1997