Simultaneous Voltammetric Determination of Zn(II), Pb(II), Cu(II), and Hg(II) in Ethanol Fuel Using an Organofunctionalized Modified Graphite‐Polyurethane Composite Disposable Screen‐Printed Device

A disposable screen‐printed device containing working, auxiliary, and reference electrodes is proposed for the simultaneous voltammetric determination of Zn(II), Pb(II), Cu(II), and Hg(II) in ethanol fuel. The working electrode was printed using an ink modified with 2‐benzothiazole‐2‐thiol organofunctionalized SBA‐15 silica, in order to increase sensitivity. The performance of this electrode was compared with that of bare and SBA‐15‐modified electrodes. After optimizing the experimental parameters, the device was applied in determination of the analytes in commercial ethanol fuel samples, using 0.10 mol L^?1 KCl/ethanol ratios of 30 : 70 (v/v), with [H⁺]=10^?5 mol L^?1. After 5 min of preconcentration at ? 1.3 V (vs. pseudo‐Ag/AgCl), four well‐resolved signals were obtained, enabling simultaneous determination of the four analytes using a differential pulse anodic stripping voltammetry (DPASV) procedure. The limits of detection were 0.30, 0.065, 0.030, and 0.046 µmol L^?1 for Zn(II), Pb(II), Cu(II), and Hg(II), respectively. The results of these analyses were in agreement with those obtained using graphite furnace atomic absorption spectroscopy (GFAAS) for Pb(II), Cu(II), and Hg(II), and high‐resolution continuum source flame atomic absorption spectrometry (HR‐CS‐FAAS) for Zn²⁺, at a 95 % confidence level. Analytes originally present in the samples could be detected, and the interference of some cations and anions was evaluated.     

Electrode Modified with Langmuir–Blodgett (LB) Film of Calixarenes for Preconcentration and Stripping Analysis of Hg(II)

A new type of current sensor, Langmuir–Blodgett (LB) film of calixarene on the surface of glassy carbon electrode (GCE) was prepared for determination of mercury by anodic stripping voltammetry (ASV). An anodic stripping peak was obtained at 0.15 V (vs. SCE) by scanning the potential from ?0.6 to +0.6 V. Compared with a bare GCE, the LB film coated electrode greatly improves the sensitivity of measuring mercury ion. The fabricated electrode in a 0.1 M H₂SO₄+0.01 M HCl solution shows a linear voltammetric response in the range of 0.07–40 μg L^?1 and detection limit of 0.04 μg L^?1 (ca. 2×10^?10 M). The high sensitivity, selectivity, and stability of this LB film modified electrode demonstrates its practical application for a simple, rapid and economical determination of Hg²⁺ in a water sample.     

Square wave anodic stripping voltammetric determination of lead(II) using a glassy carbon electrode modified with a lead ionophore and multiwalled carbon nanotubes

We report on a glassy carbon electrode (GCE) modified with a lead ionophore and multiwalled carbon nanotubes. It can be applied to square wave anodic stripping voltammetric determination of Pb(II) ion after preconcentration of Pb(II) at ?1.0?V (vs. SCE) for 300?s in pH?4.5 acetate buffer containing 400?μg?L^?1 of Bi(III). The ionophore-MWCNTs film on the GCE possesses strong and highly selective affinity for Pb(II) as confirmed by quartz crystal microbalance experiments. Under the optimum conditions, a linear response was observed for Pb(II) ion in the range from 0.3 to 50?μg?L^?1. The limit of detection (at S/N?=?3) is 0.1?μg?L^?1. The method was applied to the determination of Pb(II) in water samples with acceptable recovery.

Determination of total antimony(III,V) by square-wave anodic stripping voltammetry with in situ plated bismuth-film electrode

A sensitive and reliable method is described for the determination of total Sb(III,?V) at traces levels by Osteryoung square-wave anodic stripping voltammery (OSWASV). This method is based on the co-deposition of Sb(III,?V) with Bi(III) onto an edge-plane pyrolytic graphite substrate at an accumulation step. OSWASV studies indicated that the co-deposited antimony was oxidised with anodic scans to give an enhanced anodic peak at about 450?mV vs. Ag/AgCl (sat. KCl). The anodic stripping peak current was directly proportional to the total concentration of antimony in the ranges of 0.01–0.10?µg?L^?1, 0.10–1.0?µg?L^?1 and 1.0–18.0?µg?L^?1 with correlation coefficient higher than 0.995 when 2.0?mol?L^?1 hydrochloric acid was used. The detection limits calculated as S/N?=?3 was 5.0?ng?L^?1 in 2.0?mol?L^?1 hydrochloric acid at 180?s deposition time. The relative standard deviation was 5% (n?=?6) at 0.10?µg?L^?1 level of antimony. The analytical results demonstrate that the proposed method is applicable to analyses of real water samples.     

Electrochemical Properties of the Oxo‐Manganese‐Phenanthroline Complex Immobilized on Ion‐Exchange Polymeric Film and Its Application as Biomimetic Sensor for Sulfite Ions

A biomimetic sensor containing the oxo‐bridged dinuclear manganese‐phenanthroline complex incorporated into a cation‐exchange polymeric film deposited onto glassy carbon electrode for detection of sulfite was studied. Cyclic voltammetry at the modified electrode in universal buffer showed a two electron oxidation/reduction of the couple Mn^IV(μ‐O)₂Mn^IV/Mn^III(μ‐O)₂Mn^III. The sensor exhibited electrocatalytic property toward sulfite oxidation with a decrease of the overpotential of 450 mV compared with the glassy carbon electrode. A plot of the anodic current versus the sulfite concentration for potential fixed (+0.15 V vs. SCE) at the sensor was linear in the 4.99×10^?7 to 2.49×10^?6 mol L^?1 concentration range and the concentration limit was 1.33×10^?7 mol L^?1. The mediated mechanism was derived by Michaelis? Menten kinetics. The calculated kinetics values were Michaelis? Menten rate constant= =1.33 µmol L^?1, catalytic rate constant=6.06×10^?3 s^?1 and heterogeneous electro‐chemical rate constant=3.61×10^?5 cm s^?1.     

Determination of lead(II) in aqueous solution using carbon nanotubes paste electrodes modified with Amberlite IR-120

A new composite electrode is described for anodic stripping voltammetry determination of Pb(II) at trace level in aqueous solution. The electrode is based on the use of multiwalled carbon nanotubes and Amberlite IR-120. The anodic stripping voltammograms depend, to a large extent, on the composition of the modified electrode and the preconcentration conditions. Under optimum conditions, the anodic peak current at around ?0.57 V is linearly related to the concentration of Pb(II) in the range from 9.6?×?10^?8 to 1.7?×?10^?6 mol L^?1 (R?=?0.998). The detection limit is 2.1?×?10^?8 mol L^?1, and the relative standard deviation (RSD) at 0.24?×?10^?6 mol L^?1 is 1.7% (n?=?6). The modified electrode was applied to the determination of Pb(II) using the standard addition method; the results showed average relative recoveries of 95% for the samples analysed.

Electrocatalytic Oxidation of Acyclovir on Poly(p‐Aminobenzene Sulfonic Acid) Film Modified Glassy Carbon Electrode

Acyclovir is an antiviral effective drug active compound. A glassy carbon electrode (GCE) was modified with an electropolymerized film of p‐aminobenzene sulfonic acid (p‐ABSA) in phosphate buffer solution (PBS). The polymer film‐modified electrode was used to electrochemically detect acyclovir. Polymer film showed excellent electrocatalytic activity for the oxidation of acyclovir. The anodic peak potential value of the acyclovir at the poly(p‐ABSA) modified glassy carbon electrode was 950 mV obtained by DPV. A linear calibration curve for DPV analysis was constructed in the acyclovir concentration range 2×10^?7–9×10^?6 mol L^?1. Limit of detection (LOD) and limit of quantification (LOQ) were obtained as 5.57×10^?8 and 1.85×10^?7 mol L^?1 respectively. The proposed method exhibits good recovery and reproducibility.     

Adsorptive stripping voltammetry of nickel at a bare glassy carbon electrode

A bare glassy carbon electrode is applied to nickel determination by adsorptive stripping voltammetry in the presence of dimethylglyoxime as a complexing agent. A procedure of nickel determination and electrode regeneration was proposed. The calibration graph for Ni(II) for an accumulation time of 120?s was linear from 2?×?10^?9 to 1?×?10^?7?mol?L^?1. The detection limit was 8.2?×?10^?10?mol?L^?1. The relative standard deviation for a solution containing 2?×?10^?8?mol?L^?1 of Ni(II) was 4.1%. The proposed procedure was applied for Ni(II) determination in certified water reference materials.     

Determination of Folic Acid by Adsorptive Stripping Voltammetry at a Lead Film Electrode

An adsorptive stripping voltammetric procedure for the determination of folic acid at an in situ plated lead film electrode was described. Formation of lead film on a glassy carbon substrate and accumulation of folic acid was performed simultaneously from an acetate buffer solution of pH 5.6 at the potential ?0.88 V. The measurements were carried out from aerated solutions. The calibration graph for an accumulation time of 300 s was linear from 2×10^?9 to 5×10^?8 mol L^?1. The detection limit was 7×10^?10 mol L^?1, the relative standard deviation for 2×10^?8 mol L^?1 of folic acid was 3.9%. The proposed procedure was applied to folic acid determinations in pharmaceutical preparations.     

Anodic Stripping Voltammetric Determination of Mercury(II) in Water Using a 4‐Tert‐Butyl‐1‐(Ethoxycarbonylmethoxy)Thiacalix[4]Arene Modified Glassy Carbon Electrode

A glassy carbon electrode coated the film of 4‐tert‐butyl‐1‐(ethoxycarbonylmethoxy)thiacalix[4]arene is designed for the determination of trace amounts of Hg²⁺. Compared with bare glassy carbon electrode, the modified electrode can improve the measuring sensitivity of Hg²⁺. Under the optimum experimental condition, the modified electrode in 0.1 mol L^?1 H₂SO₄ + 0.01 mol L^?1 KCl solution shows a linear voltammetric response in the range of 8.0 × 10^?9 ～ 3.0 × 10^?6 mol L^?1 with detection limit 5.0 × 10^?9 mol L^?1 for Hg²⁺. The high sensitivity, selectivity, and stability of modified electrode also prove its practical application for a simple, rapid and economical determination of Hg²⁺ in water samples.     

Selenium-coated carbon electrode for anodic stripping voltammetric determination of copper(II)

We describe a new and promising type of selenium film electrode for anodic stripping voltammetry. This method is based on formation of copper selenide onto an in-situ formed selenium-film carbon electrode, this followed by Osteryoung square-wave anodic stripping voltammetry. Copper(II) is also in-situ electroplated in a test solution containing 0.01 mol L^-1 hydrochloric acid, 0.05 mol L^?1 potassium chloride and 500 µg L^?1 Se(IV) at a deposition potential of ?300 mV. The well-defined anodic peak current observed at about 200 mV is directly proportional to the Cu(II) concentration over the range from 1.0 to 100 µg L^?1 under the optimized conditions. The detection limit (three sigma level) is 0.2 µg L^?1 Cu(II) at 180 s deposition time. Relatively less interferences are shown from most of metal ions except for antimony(III). The method can be applied to analyses of river water and oyster tissue with good accuracy.     

Determination of Blasticidin S in Spiked Rice Using SW Voltammetry with a Renewable Silver Amalgam Film Electrode

Blasticidin S (BS) was determined in spiked rice samples by square wave voltammetry (SWV) and square wave stripping voltammetry (SWSV) using a cyclic renewable silver amalgam film electrode (Hg(Ag)FE). It was found that the compound can act as an electrocatalyst. In Britton? Robinson buffer at pH 7.0 a signal connected with the hydrogen evolution reaction was detected at ?1.2 V versus Ag/AgCl. Validation of the method was carried out. The detection and quantification limits were found to be 2.13×10^?8 mol L^?1; 7.10×10^?8 mol L^?1 for SWV and 2.65×10^?9 mol L^?1; 8.85×10^?9 mol L^?1 for SWSV, respectively.     

Catalytic Adsorptive Stripping Voltammetry of Cobalt in the Presence of Nitrite at an In Situ Plated Bismuth Film Electrode

For the first time an in situ plated bismuth film electrode has been applied to catalytic adsorptive stripping voltammetry of cobalt in the presence of nitrite. At optimised conditions bismuth film was plated before each measurement for 30 s at ?1.0 V from a sample solution with the added supporting electrolyte and Bi(III) in the form of its complex with tartrate. The calibration graph for Co(II) for an accumulation time of 120 s was linear from 5×10^?10 to 1×10^?8 mol L^?1. The detection limit was 1.1×10^?10 mol L^?1. The proposed procedure was applied for Co(II) determination in certified water reference material.     

Determination of Cesium on Nickel Hexacyanoferrate‐Aluminum Oxide Modified Electrodes

This report investigates the electrochemical behavior of hexacyanoferrate casted on Ni‐Al₂O₃ modified electrodes and the preconcentration and detection of cesium ions on such films. It also studies the morphology and the composition of these surfaces. The film was grown on a glassy carbon (GC) surface. Five consecutive voltammetric cycles applied within 0.0 V and ?1.6 V at a scan rate of 10 mV/s were enough to cast the film. Scanning electron microscopy (SEM) analyses showed a homogeneous, porous but broken surface of the film. Its composition was studied by X‐ray diffraction (XRD). The presence of NiHCFe was confirmed by Fourier transformed infrared spectroscopy (FT‐IR). The Cs⁺ preconcentration from diluted solutions was accomplished in 90 s, under a negative potential of ?0.20 V applied to the modified working electrode. The detection of cesium has a good sensitivity and a wide linear interval (10^?8 and 10^?12 mol L^?1). Even so, the limit of detection calculated was extremely low (2×10^?16 mol L^?1), cesium concentrations lower than 10^?12 mol L^?1 gave signals with no analytical significance. However, to our knowledge, this is the lowest level of cesium ever detected by an electroanalytical technique.     

Stripping Voltammetry of Mercury(II) with a Chemically Modified Carbon Paste Electrode Containing Silica Gel Functionalized with 2,5‐Dimercapto‐1,3,4‐thiadiazole

The accumulation voltammetry of mercury(II) was investigated at a carbon paste electrode chemically modified with silica gel functionalized with 2,5‐dimercapto‐1,3,4‐thiadiazole (DTTPSG‐CPE). The repetitive cyclic voltammogram of mercury(II) solution in the potential range ?0.2 to +0.8 V (vs. Ag/AgCl), (0.02 mol L^?1 KNO₃ ; v=20 mV s^?1) show two peaks one at about 0.0 V and other at 0.31 V. However, the cathodic wave peak, around 0.0 V, is irregular and changes its form in each cycle. This peak at about 0.0 V is the reduction current for mercury(II) accumulated in the DTTPSG‐CPE. The anodic wave peak at 0.31 V is well‐defined and does not change during the cycles. The resultant material was characterized by cyclic and differential pulse anodic stripping voltammetry performed with the electrode in differents supporting electrolytes. The mercury response was evaluated with respect to pH, electrode composition, preconcentration time, mercury concentration, “cleaning” solution, possible interferences and other variables. The precision for six determinations (n=6) of 0.05 and 0.20 mg L^?1 Hg(II) was 2.8 and 2.2% (relative standard deviation), respectively. The method was satisfactory and used to determine the concentration of mercury(II) in natural waters contaminated by this metal.     

Potassium ion-selective electrode based on a cobalt(II)-hexacyanoferrate film-modified electrode

A potassium ion-selective electrode based on a cobalt(II)-hexacyanoferrate(III) (CHCF) film-modified glassy carbon electrode is proposed. The electroactive film is introduced onto the glassy carbon electrode surface by electrodeposition of cobalt, which forms a thin CHCF film on subsequent anodic scanning in KClHCl solution (pH 5.0–5.5) containing K₃Fe(CN)₆. The thickness of the film on the electrode surface can be controlled by changing the electrodeposition time and the concentrations of cobalt(II) and Fe(CN)^3?₆ ions. The modified electrode exhibits a linear response in the concentration range 1 × 10^?1 ?3 × 10^?5 M potassium ion activity, with a near-Nernstian slope (48–54 mV per decade) at 25 ± 1°C. The detection limit is 1 × 10^?5 M. The stability, response time and selectivity were investigated. The electrode exhibits good selectivity for potassium ion with the twelve cations investigated. The relative standard deviation is 1.5% (n=10). The effects of the thickness of the electroactive film and the pH of the solution on the electrode response were also investigated.     

A glassy carbon electrode modified with antimony and poly(p-aminobenzene sulfonic acid) for sensing lead(II) by square wave anodic stripping voltammetry

We have developed a sensor for the square wave anodic stripping voltammetric determination of Pb(II). A glassy carbon electrode was modified with a thin film of an antimony/poly(p-aminobenzene sulfonic acid) composite in air-saturated aqueous solution of pH 2.0. Compared to a conventional antimony film electrode, the new one yields a larger stripping signal for Pb(II). The conditions of polymerization, the concentration of Sb(III), the pH value of the sample solution, the deposition potential and time, frequency, potential amplitude, and step increment potential were optimized. Under the optimum conditions, a linear response was observed for Pb(II) in the range of 0.5 to 150.0 μg?L^?1. The detection limit for Pb(II) is 0.1 μg?L^?1.

Stripping Voltammetric Determination of Zirconium with Complexing Preconcentration of Zirconium(IV) at a Morin‐Modified Carbon Paste Electrode

A sensitive, selective and economic stripping voltammetry is described for the determination of trace amounts of zirconium at a morin‐modified carbon paste electrode (morin‐MCPE). Zirconium(IV) can be preconcentrated on the surface of the morin‐MCPE due to forming the Zr(IV)–morin complex. The complex produces two second‐order derivative anodic peaks at 0.69 V (vs. SCE) and 0.75 V when linear‐scanning from 0.0 to 1.0 V. The optimum analytical conditions are: 2.2 mol L^?1 HCl, 0.0 V accummulation potential, 90 s accummulation time, 250 mV s^?1 scan rate. A linear relationships between the peak currents at 0.75 V and the Zr(IV) concentration are in the range of 2.0×10^?8 to 3.0×10^?6 mol L^?1. The detection limit is 1.0×10^?8 mol L^?1 (S/N=3) for 120 s accumulation. The RSD for determination of 4.0×10^?7 mol L^?1 Zr(IV) is 4.8% (n=8). The proposed method has been applied to determine zirconium in ore samples, unnecessarily extracted.     

Palladium Particles‐Impregnated Natural Phosphate Electrodes for Electrochemical Determination of Mercury in Ambient Water Samples

We present here a simple procedure for the determination of mercury(II) using differential pulse anodic stripping voltammetry (DPASV) at palladium particles‐impregnated natural phosphate modified carbon paste electrodes (Pd‐NP‐CPE). The surface of modified electrode was characterized using SEM, infrared spectroscopy, X‐ray diffraction and electrochemical analysis. All experimental variables involved in the voltammetric stripping method were optimized. The detection limit was found to be 4.99×10^?8 mol L^?1 (S/N=3) that is not different to the permitted value for Hg(II) in water reported by the Environmental Protection Agency (EPA). The proposed electrode exhibits good applicability for monitoring Hg(II) in tap and wastewater.     

Fabrication of Bismuth/Multi-walled Carbon Nanotube Composite Modified Glassy Carbon Electrode for Determination of Cobalt

A bismuth/multi‐walled carbon nanotube (Bi/MWNT) composite modified electrode for determination of cobalt by differential pulse adsorptive cathodic stripping voltammetry is described. The electrode is fabricated by potentiostatic pre‐plating bismuth film on an MWNT modified glassy carbon (GC) electrode. The Bi/MWNT composite modified electrode exhibits enhanced sensitivity for cobalt detection as compared with the bare GC, MWNT modified and bismuth film electrodes. Numerous key experimental parameters have been examined for optimum analytical performance of the proposed electrode. With an adsorptive accumulation of the Co(II)‐dimethylglyoxime complex at ?0.8 V for 200 s, the reduction peak current is proportional to the concentration of cobalt in the range of 4.0×10^?10?1.0×10^?7 mol/L with a lower detection limit of 8.1×10^?11 mol/L. The proposed method has been applied successfully to cobalt determination in seawater and lake water samples.