Highly Selective and Sensitive Triiodide PVC‐Membrane Electrode Based on a New Charge‐Transfer Complex of Bis(2,4‐Dimethoxybenzaldehyde)butane‐2,3‐Dihydrazone with Iodine

In this work, a highly selective membrane triiodide sensor based on a new charge‐transfer complex of bis(2,4‐dimethoxybenzaldehyde)butane‐2,3‐dihydrazone with iodine (Iodide Charge Transfer complex: ICT) as membrane carrier is introduced. The influences of five different solvent mediators on sensitivity and selectivity of the proposed sensor were considered. The best performance was obtained with the membrane composition containing 30% poly (vinyl chloride), 63% DBP, 5% ICT and 2% HTAB. The electrode shows a Nernstian behavior over a very wide triiodide ion concentration range (1.0 × 10^?7‐1.0 × 10^?2 M), and a detection limit value of 8.0 × 10^?8 M. The effect of pH on the potentiometric response of the sensor was also studied, and it was found that the response of the electrode is independent of the pH of the solution in the pH range of 4.0–10. The proposed sensor has a very fast response time (< 12 s), and good selectivities relative to a wide variety of common inorganic and organic anions, including iodide, acetate, bromide, chloride, fluoride, nitrite, nitrate, sulfite, sulfate, cyanide and thiocyanate. In fact the selectivity behavior of the proposed triiodide ion‐selective electrode shows great improvements compared to the previously reported electrodes for triiodide ion. The proposed membrane sensor can be used for at least 6 months without any divergence in the potentials. The electrode was successfully applied as an indicator electrode in the titration of triiodide with thiosulfate ion.     

Triiodide Ion‐Selective Electrode Based on Charge‐Transfer Complex of 4,7,13,16,21,24‐Hexaoxa‐1,10‐diazabicyclo‐[8.8.8]hexacosane

Two new highly selective triiodide electrodes have been prepared using charge‐transfer complex of iodine with cryptand 222 as an electroactive ionophore and nitrophenyl octyl ether as a plasticizing agent. The electrodes showed Nernstian response to triiodide ions over a concentration range from 1.0 × 10^?;2 — 7.9 × 10^?;7 M and from 1.0 × 10^?;2 — 1 × 10^?;6 M with detection limits of 6.3 × 10^?;7 and 7.9 × 10^?;7 M for cryptand and its charge‐transfer complex with iodine, respectively. The response times (t_95%) of the sensors were 10 and 5 s. The membrane could be used for more than 1 month without any divergence in potentials. The proposed sensors exhibited very high selectivity for triiodide ion over other anions, and could be used in a wide pH range ?2–10. These electrodes were successfully applied as an indicator electrode in potentiometric titration of copper in ore samples.     

Ketoconazol‐Triiodide Ion Pair Complex as a Suitable Carrier in an Iodide Selective Membrane Electrode

A novel membrane sensor for selective monitoring of iodide, consisting of a triiodide‐ketoconazole ion pair complex dispersed in a PVC matrix, plasticized with a mixture of 2‐nitrophenyl octyl ether and dioctylphtalate with unique selectivity toward iodide ions, is described. The influence of membrane composition, pH of test solution and foreign ions on the electrode performance were investigated. The optimized membrane demonstrates a near‐Nernstian response for iodide ions over a wide linear range from 1.0 × 10^?2 to 1.0 × 10^?5 M, at 25 ± 1 °C. The electrode could be used over a wide pH range 3–10 and has the advantages of high selectivity, fast response time and good lifetime (over 4 months). It was successfully used as indicator electrode in potentiometric titrations and direct potentiometric assay of iodide ions.     

Highly Selective and Sensitive Triiodide PVC‐Based Membrane Electrode Based on a New Charge Transfer Complex of 2‐(((2‐(((E)‐1‐(2‐Hydroxyphenyl) Methylidine) Amino) Phenyl) Imino) Methyl) Phenol for Nano‐Level Monitoring of Triiodide

Abstract

A highly selective and sensitive triiodide sensor based on a 2‐(((2‐(((E)‐1‐(2‐hydroxy phenyl) methylidine) amino) phenyl) imino) methyl) phenol with iodine (CTC) as membrane carrier was developed. The electrode revealed a Nernstian behavior over a very wide triiodide‐ion concentration range (5.0×10^?8–1.0×10^?2 M), and relatively low detection limit (3.0×10^?8 M). The potentiometric response is independent of the pH of solution in the pH range of 3.0–10.0. The electrodes manifest advantages of low resistance, very fast response (<12 s), and most importantly, good selectivities relative to a wide variety of inorganic and organic anions, including iodide, bromide, chloride, fluoride, sulfite, sulfate, cyanide, thiocyanate, and acetate. In fact, the selectivity behavior of the proposed triiodide ion‐selective electrode shows great improvements compared to the previously reported electrodes for the triiodide ion. The proposed membrane sensor can be used for at least 6 months without any significant divergences in the potential. The electrode was successfully applied as an indicator electrode in the titration of triiodide with thiosulfate ion.     

Highly Selective PVC‐Based Membrane Electrode Based on 2,6‐Diphenylpyrylium Fluoroborate

A highly selective PVC‐membrane electrode based on 2,6‐diphenylpyrylium fluoroborate is presented. The electrode reveals a Nernstian potentiometric response for sulfate ion over a wide concentration range (5.0 × 10^?6‐1.0 × 10^?1 M). The electrode has a response time of about 10 s and can be used for at least 2 months without any divergence. The proposed sensor revealed very good selectivities for sulfate over a wide variety of common organic and inorganic anions and could be used over a wide pH range (2.5–9.5). The detection limit of the sensor is 3.0 × 10^?6 M. It was successfully applied to the direct determination of salbutamol, paramomycin tablets, and as an indicator electrode for potentiometric titration of sulfate ions with barium ions.     

Iodide‐Selective Electrode Based on Copper Phthalocyanine

Copper phthalocyanine was used as ion carrier for preparing polymeric membrane selective sensor for detection of iodide. The electrode was prepared by incorporating the ionophore into plasticized poly(vinyl chloride) (PVC) membrane, coated on the surface of graphite electrode. This novel electrode shows high selectivity for iodide with respect to many common inorganic and organic anions. The effects of membrane composition, pH and the influence of lipophilic cationic and anionic additives and also nature of plasticizer on the response characteristics of the electrode were investigated. A calibration plot with near‐Nernestian slope for iodide was observed over a wide linear range of five decades of concentration (5×10^?6?1×10^?1 M). The electrode has a fast response time, and micro‐molar detection limit (ca. 1×10^?6 M iodide) and could be used over a wide pH range of 3.0–8.0. Application of the electrode to the potentiometric titration of iodide ion with silver nitrate is reported. This sensor is used for determination of the minute amounts of iodide in lake water samples.     

A Highly Selective and Sensitive Barium(II)‐Selective PVC Membrane Based on Dimethyl 1‐Acetyl‐8‐oxo‐2,8‐dihydro‐ 1H‐pyra‐zolo[5,1‐a]isoindole‐2,3‐dicarboxylate

A poly(vinyl chloride)‐based membrane of dimethyl 1‐acetyl‐8‐oxo‐2,8‐dihydro‐1H‐pyra‐zolo[5,1‐a]isoindole‐2,3‐dicarboxylate as a neutral carrier with sodium tetraphenylborate (NaTPB) as an anion excluder and 2‐nitrophenyl octyl ether (NPOE) as plasticizer was prepared and investigated as a Ba(II)‐selective electrode. The electrode exhibits a Nernstian slope of 29.7±0.4 mV per decade over a wide concentration range (1.0×10^?6 to 1.0×10^?1 M) with a detection limit of 7.6×10^?7 M between pH 3.0 and 11.0. The response time of the sensor is about 10 s and it can be used over a period of 2 months without any divergence in potential. The proposed membrane sensor revealed good selectivity for Ba(II) over a wide variety of other metal ions. It was successfully used in direct determination of barium ions in industrial wastewater samples.     

Voltammetric Determination of Xanthine with a Single‐Walled Carbon Nanotube‐Ionic Liquid Paste Modified Glassy Carbon Electrode

Single‐walled carbon nanotube (SWNT) and room temperature ionic liquid (i.e., 1‐butyl‐3‐methylimidazolium hexaflourophosphate, BMIMPF₆) were used to fabricate paste modified glassy electrode (GCE). It was found that the electrode showed sensitive voltammetric response to xanthine (Xt). The detection limit was 2.0×10^?9 M and the linear range was 5.0×10^?9 to 5.0×10^?6 M. The electrode also displayed good selectivity and repeatability. In the presence of uric acid (UA) and hypoxanthine (Hx) the response of Xt kept almost unchanged. Thus this electrode could find application in the determination of Xt in some real samples. The analytical performance of the BMIMPF₆‐SWNT/GCE was demonstrated for the determination of Xt in human serum and urine samples.     

Nanobiocomposite Modified Carbon‐Ceramic Electrode Based on Nano‐TiO2‐Plant Tissue and Its Application for Electrocatalytic Oxidation of Dopamine

A new modified carbon‐ceramic electrode was prepared by incorporating TiO₂ nanoparticle into sol‐gel network by accompanying apple tissue. A mixture of fine graphite powder with 15 wt% of TiO₂ nanoparticle was used for the preparation of the carbon matrix and finally modification with a known amount weighted of apple tissue. The apple tissue containing polyphenol oxidase enzyme acts as molecular recognition element. The electrocatalytic oxidation of dopamine was investigated on the surface of the nanobiocomposite modified carbon‐ceramic electrode using cyclic voltammetry, chronoamperometry and amperometry techniques. Effect of pH, scan rate, TiO₂ percentage on the response of modified electrode was studied. The prepared modified electrode presented a linear range for dopamine from 5.0×10^?6 to 1.2×10^?3 M in buffered solutions with pH 7.4 by amperometry. The detection limit was 3.41×10^?6 M dopamine. The response of the modified carbon‐ceramic electrode and unmodified carbon‐ceramic electrode was compared.     

Homooxacalix[3]arene Derivatives as Ionophores for Serotonin‐Selective Membrane Electrodes

Homooxacalix[3]arene derivatives are effective ionophores for constructing serotonin‐selective membrane electrodes. An electrode based on one of the derivatives, tris(methoxyphenylpropyloxy)hexahomooxacalix[3]arene‐triethyl ether, with potassium tetrakis(p‐chlorophenyl)borate (20 mol% relative to the ionophore) as an ionic additive and bis(2‐ethylhexyl) sebacate as a solvent mediator in a poly(vinyl chloride) membrane matrix, displayed much better selectivity for serotonin than for various organic ammonium ions and inorganic cations. The electrode exhibited a near‐Nernstian response to serotonin in the concentration range of 2×10^?4 to 1×10^?2 M with a slope of 56.4 mV per concentration decade in physiological saline containing 150 mM NaCl and 10 mM Na₂HPO₄/NaH₂PO₄ (pH 7.4). The limit of the detection was 8×10^?5 M. The selectivity pattern of this electrode was quite different from that of an electrode using calix[6]arene‐hexaacetic acid hexaethyl ester, a well‐known ionophore for primary organic ammonium ions, which did not induce an enhanced response to serotonin. The developed electrode was used for the active loading of serotonin in liposomes induced by transmembrane pH gradients.     

Efficient Synthesis of a New Podand and Application as a Suitable Carrier for Silver Ion‐Selective Electrode

A new podand of 1,1′‐thia‐bis‐[1‐(chloroethan‐2‐acetamid‐α‐oxy)] naphtol was synthesized and used as a suitable carrier for Ag⁺ PVC membrane electrode. The electrode exhibited linear response with a Nernstian slope of (59.5±0.8 mV/decade) within a wide concentration range of 1.0×10^?7 to 1.5×10^?2 mol L^?1 silver ions. The electrode had a fast response time of <10 s and detection limit of 8.6×10^?8 mol L^?1 with a working pH range from 3.7 to 9.0. The electrode was highly selective for Ag(I) ions over a large number of cations such as alkali, alkaline earth, and heavy metal ions. The proposed sensor has been applied as an indicator electrode for indirect determination of vitamin B₁ in tablets by determination of Cl^? ions in this compound with a standard solution of Ag(NO₃).     

Zn(II)‐Selective Membrane Electrode Based on Tetraazamacrocycle [Bzo2Me2Ph2(16)hexaeneN4]

A PVC membrane electrode using [Bzo₂Me₂Ph₂(16)hexaeneN₄] ( I ) as ionophore, oleic acid as lipophilic additive and o‐nitrophenyloctyl ether as plasticizer has been investigated as Zn(II)‐selective electrode. The membrane incorporating 34.9% (w/w) PVC, 2.3% I , 4.7% OA and 58.1% o‐NPOE gave linear response over the concentration range 2.82×10^?6?1.0×10^?1 M with a Nernstian slope of 28.5±0.2 mV/decade of concentration with a detection limit of 2.24×10^?6 M (0.146 ppm) and showed a response time of less than 10 s and could be used in pH range 2.5–8.5. High selectivity was obtained over a wide variety of metal ions. The proposed electrode was successfully used as an indicator electrode in potentiometric titration of zinc ions with EDTA and for determination of zinc in real samples.     

New PVC-membrane electrode based on charge-transfer inclusion complex between I2 and 1,4,8,11-tetraazacyclotetracdecane for selective determination of I3 − ions

A new triiodide ion-selective electrode based on charge-transfer complex of iodine with 1,4,8,11-tetraazacyclotetracdecane as membrane carrier was prepared. The best performance of electrode observed with the membrane having the ligand–PVC–NPOE–NaTPB composition 3.0:33:66:0.5 mg which worked well over a wide concentration range 2.8 × 10^?6–1.4 × 10^?1 M with a Nernstian slope of 59.6 ± 0.3 mV per decade and a detection limit of 1.2 × 10^?6 M. This electrode showed a response time of 25 s and was used over a period of 2 months. The electrode exhibits an anti-Hofmeister selectivity sequence with a performance for triiodide at pH 1.5–10.2. The response mechanism of the electrode was investigated by UV–Vis spectroscopic technique. The electrode was successfully applied as an indicator electrode in the potentiometric titration of ascorbic acid and hydroquinone in drugs.     

[Cu(L)](NO3)2 (L=4,7‐Bis(3‐aminopropyl)‐1‐thia‐4,7‐diazacyclononane) as a Suitable Ionophore for Construction of Thiocyanate‐Selective Electrodes and Their Use in Determination of Urinary and Salivary Thiocyanate Concentration

The construction, performance characteristics, and application of polymeric membrane (PME) and coated graphite (CGE) thiocyanate‐selective electrodes are reported. The electrodes were prepared by incorporating the complex [Cu(L)](NO₃)₂ (L=4,7‐bis(3‐aminopropyl)‐1‐thia‐4,7‐diazacyclononane) into a plasiticized poly(vinyl chloride) membrane. The influence of membrane composition, pH of test solution, and foreign ions were investigated. The electrodes reveal Nernstian behavior over a wide SCN^? ion concentration range (1.0×10^?6–1.0×10^?1 M for PME and 5.0×10^?7–1.0×10^?2 M for CGE) and show fast dynamic response times of 15 s and lower. The proposed sensors show high selectivity towards thiocyanate over several common organic and inorganic anions. They were successfully applied to the direct determination of thiocyanate in urine and saliva of smokers and nonsmokers, and as an indicator electrode in titration of Ag⁺ ions with thiocyanate.     

牛磺酸双核铜络合物为载体的高选择性硫氰酸根离子电极的研究

本文报道了一种以牛磺酸双核铜络合物为中性载体的硫氰酸根PVC膜电极。该电极对硫氰酸根有良好的电位响应并呈现出anti-Hofmeister行为,其选择性顺序SCN^->I^->ClO₄^->Sal^->NO₃^-> NO₂^-> Br^- > Cl^- > SO₃^-> SO₄ ^2-。在20℃ pH 5.0的磷酸缓冲溶液中,其线性范围为1.0´10 ^-1~ 1.0´10^-6mol×L-1,检测线为8.0×10 ^-7mol•L^-1,斜率为 -56.5 mV/pcSCN^-。紫外、红外和交流阻抗研究表明电极的高选择性与载体的立体结构和分析物与中心金属离子的作用相关。将该电极用于废水和人体尿液中硫氰酸根的测定,获得了较满意的结果。     

Determination of Cr(VI) with Selective Sensing of Cr(VI) Anions by a PVC‐Membrane Electrode Based on Quinaldine Red

A dichromate‐selective PVC‐membrane electrode based on Quinaldine Red (an acridinium derivative) is described. The electrode exhibits rapid (< 30 s) and linear response to the activity of Cr(VI) anions in the range of 5.2 × 10^?6 ?1.0 × 10^?1 M dichromate with the limit of detection 2.5 × 10^?6 Mof Cr₂O₇^2?. The sensor is used as an indicator electrode in potentiometric determination of Cr(VI) anions and is also suitable for end‐point indication in the titrations of proper metal ions with dichromate under laboratory conditions. The proposed electrode has been applied to the direct potentiometric determination of Cr(VI) anions in water samples with satisfactory results.     

Novel Gadolinium PVC‐Based Membrane Sensor Based on Omeprazole as an Antibiotic

A novel gadolinium ion‐selective electrode based on the antibiotic omeprazole as membrane carrier was prepared. The electrode has a linear dynamic range between 1.0×10^?1 and 1.0×10^?5 M, with a Nernstian slope of 19.3 ± 0.3 mV decade^?1 and a detection limit of 5.0×10^?6 M. The potentiometric response is independent of the pH of the solution in the pH range 4.0–10.0. The electrode possesses the advantages of short conditioning time, fast response time and especially, very good selectivity over a large number of other cations. The electrode can be used for at least 2 months without any considerable divergence in potentials. It was used as an indicator electrode in potentiometric titration of Gd(III) ions with EDTA.     

A Novel PVC‐Membrane‐Coated Graphite Sensor Based on an Anthraquinone Derivative Membrane for the Determination of Lead

A highly selective membrane electrode for the determination of ultratrace amounts of lead was prepared. The PVC membrane electrode based on 2‐(2‐ethanoloxymethyl)‐1‐hydroxy‐9,10‐anthraquinone (AQ), directly coated on graphite, exhibits a good Nernstian response for Pb(II) ions over a very wide concentration range (1.0×10^?7–1.0×10^?2 M) with a limit of detection of 8.0×10^?8 M. It has a fast response time of ca. 10 s and can be used over a period 2 months with good reproducibility (SD=±0.2 mV). The electrode revealed a very good selectivity respect to common alkali, alkaline earth, transition and heavy metal ions and could be used in the pH range of 3.5–6.8. It was used as an indicator electrode in potentiometric titration of lead ions with chromate and oxalate, and in indirect determination of lead in spring water samples.     

Highly Selective and Sensitive Copper(II) Membrane Sensors Based on 6‐Methyl‐4‐(1‐phenylmethylidene)amino‐3‐thioxo‐1,2,4‐triazin‐5‐one as a New Neutral Ionophore

A new Cu(II) ion‐selective PVC membrane sensor based on 6‐methyl‐4‐(1‐phenylmethylidene)amino‐3‐thioxo‐1,2,4‐triazin‐5‐one (MATTO) as an excellent sensing material was developed. The electrode exhibits a Nernstian slope of 29.2±0.4 mV per decade over a very wide concentration range between 1.0×10^?1 and 1.0×10^?6 M, with a detection limit of 4.8×10^?7 M (30.5 ng/mL). The sensor possesses the advantages of short conditioning time, fast response time (<10 s), and especially, very good selectivity towards transition and heavy metal, and some mono, di and trivalent cations. The proposed electrode was successfully applied to the determination of copper in wastewater of copper electroplating samples and as an indicator electrode in potentiometric titration of Cu(II) ions with EDTA.     

Polymeric Membrane Lanthanum(III)‐Selective Electrode Based on N,N′‐Adipylbis(5‐phenylazo salicylaldehyde hydrazone)

A recently synthesized azao‐containing Schiff's base N,N′‐adipylbis(5‐phenylazo salicylaldehyde hydrazone) was used as a suitable neutral ion carrier in construction of a highly selective La³⁺‐PVC membrane electrode. The electrode exhibits a Nernstian response with a slope of 19.4 mV decade^?1 over a wide concentration range (1.0×10^?6–1.0×10^?2 M) and a limit of detection of 4.0×10^?7 M (0.05 ppm). The electrode possesses a fast response time of ca. 10 s and can be used for at least 3 months without observing any deviation. The proposed electrode revealed excellent selectivity for La³⁺ over a wide variety of alkali, alkaline earth, transition and heavy metal ions and could be used in a pH range of 4.0–8.0. The practical utility of the electrode has been demonstrated by its use as an indicator electrode in the potentiometric titration of La³⁺ ions with EDTA and in determination of F^? ion in some pharmaceutical preparations.