Speciation of Cr(III) and Cr(VI) using solid phase extraction and determination of total As inductively coupled plasma atomic emission spectrometry

An inductively coupled plasma atomic emission spectrometric (ICP-AES) method was developed for speciation and simultaneous determination of Cr and As, since these two analytes are commonly determined in various water samples in order to assess their toxicity. The objective of this research was to study the speciation of Cr(III), Cr(VI) in the presence of As(III) and/or As(V) using solid phase extraction (SPE) and ICP-AES. For these measurements, four spectral lines were used for each analyte with the purpose of selecting the most appropriate for each element. Finally with the use for first time of a cation-exchange column filled with benzosulfonic acid and elution with HCl, the speciation in solutions which contained [Cr(III)?+?Cr(VI)?+?As(V)] and [Cr(III)?+?Cr(VI)?+?As(III)] was examined. It was demonstrated that the separation of the two chromium species is almost quantitative and the simultaneous determination of chromium species and total arsenic analytes is possible, with very good performance characteristics. The estimated limits of detection for Cr(III), Cr(VI), As(III) and/or As(V) were 0.9?µg?L^?1, 1.1 µg?L^?1, 4.7 µg?L^?1 and 4.5 µg?L^?1 respectively, the calculated relative standard deviations (RSDs) were 3.8%, 4.1%, 5.2% and 5.1% respectively, and finally the accuracy of the methods was estimated using a certified aqueous reference material and found to be 5.6% and 4.8% for Cr(III) and Cr(VI) respectively. The method was applied to the routine analysis of various water samples.     

Ultraselective and Sensitive Determination of Cr(VI) in the Presence of a High Excess of Cr(III) in Natural Waters with a Complicated Matrix

In the present work, the catalytic adsorptive stripping voltammetric procedure for trace determination of Cr(VI) in the presence of a high excess of Cr(III) in natural waters with a complicated matrix has been developed. The influence from potentially interfering substances such as organic matter was successfully eliminated by exploiting adsorptive properties of polymeric resin. The detection limit estimated from 3 times the standard deviation for a low Cr(VI) concentration in the simultaneous presence of a 2×10³ fold excess of Cr(III), 50 mg L^?1 surfactants, 50 mg L^?1 humic substances and the accumulation time of 30 s was about 5.3×10^?10 mol L^?1.     

Preconcentration and separation of Cr(III) and Cr(VI) using sawdust as a sorbent

A simple, inexpensive method based on solid-phase extraction (SPE) on sawdust from Cedrus deodera has been developed for speciation of Cr(III) and Cr(VI) in environmental water samples. Because different exchange capacities were observed for the two forms of chromium at different pH—Cr(III) was selectively retained at pH 3 to 4 whereas Cr(VI) was retained at pH 1—complete separation of the two forms of chromium is possible. Retained species were eluted with 2.5 mL 0.1 mol L⁻¹ HCl and 0.1 mol L⁻¹ NaOH. Detection limits of 0.05 and 0.04 μg mL⁻¹ were achieved for Cr(III) and Cr(VI), respectively, with enrichment factors of 100 and 80. Recovery was quantitative using 250 mL sample volume for Cr(III) and 200 mL for Cr(VI). Different kinetic and thermodynamic properties that affect sorption of the chromium species on the sawdust were also determined. Metal ion concentration was measured as the Cr(VI)–diphenylcarbazide complex by UV–visible spectroscopy. The method was successfully applied for speciation of chromium in environmental and industrial water samples.     

Speciation Analysis of Cr(III) and Cr(VI) after Solid Phase Extraction Using Modified Magnetite Nanoparticles

A new solid phase extraction (SPE) method has been developed for the speciation of Cr(III) and Cr(VI). This method is based on the adsorption of Cr(VI) on modified alumina‐coated magnetite nanoparticles (ACMNPs). Total chromium in different samples was determined as Cr(VI) after oxidation of Cr(III) to Cr(VI) using H₂O₂. The chromium concentration has been determined by flame atomic absorption spectrometric (FAAS) technique and amount of Cr(III) was calculated by substracting the concentration of Cr(VI) from total chromium concentration. The effect of parameters such as pH, amount of adsorbent, contact time, sample volume, eluent type, H₂O₂ concentration and cetyltrimethylammonium bromide (CTAB) concentration as modifier on the quantitative recovery of Cr(VI) were investigated. Under the optimal experimental conditions, the preconcentration factor, detection limit, linear range and relative standard deviation (RSD) of Cr(VI) were 140 (for 350 mL of sample solution), 0.083 ng mL^?1, 0.1‐10.0 ng mL^?1 and 4.6% (for 5.0 ng mL^?1, n = 7), respectively. This method avoided the time‐consuming column‐passing process of loading large volume samples in traditional SPE through the rapid isolation of CTAB@ACMNPs with an adscititious magnet. The proposed method was successfully applied to the determination and speciation of chromium in different water and wastewater samples and suitable recoveries were obtained.     

Simultaneous determination of Cr(III) and Cr(VI) with prechelation of Cr(III) using phthalate by ion interaction chromatography with a C-18 column

Ion interaction chromatography has been successfully used for the simultaneous determination of Cr(III) and Cr(VI) in waste water. A C-18 column which had been dynamically coated with octylamine was used for the separation of Cr(III) and Cr(VI) based on anionic interaction. Cr(III) was chelated with potassium hydrogen phthalate (KHP) before injecting into the column since the Cr(III) did not exist in an anionic form like the Cr(VI) (Cr₂O₇²⁻) presented at the optimum condition. The analytes were detected at 200 nm and linear relationship between absorption with the concentration of Cr(III) or Cr(VI) was 0.1-50 mg/L. Most of the interested interferences including alkali metals, heavy metals and organic materials have no significant effect on Cr(III)-KHP complexation and Cr(VI) stability, only NH₄⁺ and ascorbic acid yielded the serious effect on the Cr(VI) stability. The relative standard deviations calculated from both of peak area and retention time were 0.75-2.20%. The sensitivity of the method at the level concentration of sub mg/L enabled the simultaneous determination of Cr(III) and Cr(VI) contents in waste water samples without any special sample preparation step.     

Determination of Cr(VI) in the Presence of Complexing Agents and Humic Substances by Catalytic Stripping Voltammetry

The voltammetric method of Cr(VI) determination in a flow system is proposed. Determinations can be carried out in the simultaneous presence of an excess of Cr(III), complexing agents, humic substances and surfactants. The method is based on the combination of a selective accumulation of the product of Cr(VI) reduction to the metallic state and a very sensitive voltammetric method of chromium determination in the presence of DTPA and nitrates. The calibration graph is linear from 1×10^?9 to 5×10^?8 mol L^?1 for accumulation time of 30 s. The relative standard deviation is 5.2% (n=5) for Cr(VI) concentration 1×10^?8 mol L^?1. The influence of humic and fulvic acids, complexing agents and surfactants on Cr(VI) and the interfering Cr(III) signal is presented. The method was applied to Cr(VI) determination in certified reference material, soil sample, natural water sample and EDTA extracts from soil certified reference material.     

Application of double-spike isotope dilution for the accurate determination of Cr(III), Cr(VI) and total Cr in yeast

A method is presented for the simultaneous determination of Cr(III) and Cr(VI) in yeast using species-specific double-spike isotope dilution (SSDSID) with anion-exchange liquid chromatography (LC) separation and sector field inductively coupled plasma mass spectrometric (SF-ICP-MS) detection. Total Cr is quantitated using ID SF-ICP-MS. Samples were digested on a hot plate at 95±2 °C for 6 h in an alkaline solution of 0.5 M NaOH and 0.28 M Na₂CO₃ for the determination of Cr(III) and Cr(VI), whereas microwave-assisted decomposition with HNO₃ and H₂O₂ was used for the determination of total Cr. Concentrations of 2,014±16, 1,952±103 and 76±48 mg kg⁻¹ (one standard deviation, n=4, 3, 3), respectively were obtained for total Cr, Cr(III) and Cr(VI) in the yeast sample. Significant oxidation of Cr(III) to Cr(VI) (24.2±7.6% Cr(III) oxidized, n=3) and reduction of Cr(VI) to Cr(III) (37.6±6.5% Cr(VI) reduced, n=3 ) occurred during alkaline extraction and subsequent chromatographic separation at pH 7. Despite this significant bidirectional redox transformation, quantitative recoveries for both Cr(III) and Cr(VI) were achieved using the SSDSID method. In addition, mass balance between total Cr and the sum of Cr(III) and Cr(VI) concentrations was achieved. Method detection limits of 0.3, 2 and 30 mg kg⁻¹ were obtained for total Cr, Cr(VI) and Cr(III), respectively, based on a 0.2-g sub-sample.     

Simultaneous Determination of Antimony(III) and Molybdenum(VI) by Adsorptive Stripping Voltammetry Using Quercetin as Complexing Agent

A sensitive and selective voltammetric method for simultaneous determination of Sb(III) and Mo(VI) using Quercetin (Q) as complexing agent is described. Optimal conditions were found to be: pH 3.7, C_Q=6.0 µmol L^?1 and E_acc=?0.10 V. The LOD (3σ) for Sb(III) are 0.076 and 0.040 µg L^?1, whereas for Mo(VI) are 0.086 and 0.048 µg L^?1 with t_acc of 60 and 120 s, respectively. The method was validated using synthetic sea water (ASTM D665) and was applied to the determination of Sb(III) and Mo(VI) in natural waters with satisfactory results.     

Polarographic studies of catalytic reduction of hydrogen in Cr(VI)−As(III) and Cr(III)—As(III) systems

In the presence of traces of Cr(VI) or Cr(III) ions in ammonia or borate buffers containing the As(III) ions a catalytic hydrogen wave arises in the dc polarogram. It was established that the complex Cr(H₂AsO₃)_n^+3?n is formed in the solution, and that its reduced form adsorbed at DME is of catalytic activity. The wave can be employed for the determination of low concentrations (2×10^?8×10^?7M) of Cr(VI) and Cr(III) ions.     

Separation and spectrophotometric determination of very low levels of Cr(VI) in water samples by novel pyridine-functionalized mesoporous silica

A modified SBA-15 mesoporous silica was developed, as an adsorbent, for the removal of Cr(VI) ions from natural-water samples. The effects of experimental parameters, including pH of solution, sample and eluent flow rate, the eluent composition, the eluent volume, and the effect of coexisting ions on the separation and determination of Cr(VI), were investigated. It was shown that Cr(VI) was selectively adsorbed from aqueous solution at pH 3, but Cr(III) could be adsorbed from solution at alkaline pH range. The retained Cr(VI) was eluted with 0.5?mol?L^?1 KCl solution in 0.1?mol?L^?1 Na₂CO₃ subsequently. Under the optimum conditions, the modified mesoporous silica (py-SBA-15) with a high pore diameter exhibited an adsorption capacity of 136?mg?g^?1 and a lower limit of detection than 2.3?µg?L^?1 by using diphenylcarbazide as a chromophorous reagent for the determination of Cr(VI) ions. A preconcentration factor as high as 200 was calculated for Cr(VI). The loaded py-SBA-15 can be reactivated with recovery of more than 98.5% over at least eight cycles. The relative standard deviation (RSD) for Cr(VI) ion recovery was less than 1.8%. Validation of the outlined method was performed by analysing a certified reference material (BCR 544). The proposed method was applied to determine Cr(VI) value in natural and waste water samples successfully.     

Determination of Cr(VI) by Catalytic Adsorptive Stripping Voltammetry with Application of Nitrilotriacetic Acid as a Masking Agent

A selective and sensitive method for determination of traces of Cr(VI) in the presence of a large excess of Cr(III) by differential pulse catalytic adsorptive stripping voltammetry is presented. For minimization of Cr(III) interference nitrilotriacetic acid was used as a masking agent. The determinations were performed in a flow system. The calibration plot was linear from 1×10⁻¹⁰ to 1×10⁻⁸ mol L⁻¹ for accumulation time 60 s. The relative standard deviation for 3×10⁻⁹ mol L⁻¹ Cr(VI) was 4.1% (n=5). The detection limit for an accumulation time of 60 s was 4×10⁻¹¹ mol L⁻¹. The influence of common foreign ions is also presented. The performance of the method was verified by analysis of certified reference material for Cr(VI) and comparing the results of analyses of natural water samples with those obtained by another accepted electrochemical method.     

Fluorimetric Cr(VI) and Cr(III) Speciation With Crystal Violet

Abstract

A simple fluorimetric determination of Cr(VI) in the presence of Cr(III) is described. This determination is based on the fluorescence, produced from the ion-association complex between the Crystal violet cation and the anionic complex, formed between Cr(VI) and excess of I^?. This fluorescence is not observed when Cr(III) is used instead of Cr(VI). The fluorescence intensity is linear over the concentration range of 0–60 μg/1. The method was applied in potable and sea waters.     

Simple and Highly Selective Catalytic Adsorptive Voltammetric Method for Cr(VI) Determination

A simple and highly selective and sensitive catalytic adsorptive stripping voltammetric procedure for determination of traces of Cr(VI) in the presence of a large excess of Cr(III) in environmental water samples is reported. To obtain a low detection limit the voltammetric procedure of chromium determination in the presence of DTPA and nitrate was exploited. For elimination of interference of Cr(III) ethylenediaminedisuccinic acid was used as a masking agent. At optimized conditions the calibration graph is linear from 2×10^?10 to 2×10^?8 mol L^?1 for accumulation time of 30 s. The validation of the procedure was performed by comparison of the results of analysis of river water samples with those obtained using other accepted voltammetric procedure.     

Ionic liquid-modified silica-coated magnetic nanoparticles; promising anion-exchange sorbent for extraction of Cr(VI)

In the present study, ionic liquid-modified silica-coated magnetic nanoparticles (MNPs) were synthesised and applied as a new anion-exchange sorbent for extraction and determination of Cr(VI) followed by inductively coupled plasma atomic emission spectrometry. The characterisation of MNPs was carried out by scanning electron microscope, Fourier transform infrared and vibrating sample magnetometer. Experimental design and response surface methodology were used for optimisation of different parameters which affect extraction efficiency of Cr(VI). Under the optimised conditions, extraction recoveries within the range of 25–33% with relative standard deviations (RSD%, n = 4) within the range of 3.0–5.0% were obtained. The limit of detection was found to be 0.1 µg L^?1. The linearity was studied in the range of 0.5-200 µg L^?1 with the determination coefficient of 0.9958. Also, calculated Errors% for determination of Cr(VI) in the range of 5-15 depict that the method offers acceptable accuracy for analysis of Cr(VI). The method was successfully applied for extraction and determination of Cr(VI) selectively in some tannery waste water samples.     

Speciated isotope dilution analysis of Cr(III) and Cr(VI) in water by ICP-DRC-MS

An isotope dilution method has been developed for the speciation analysis of chromium in natural waters which accounts for species interconversions without the requirement of a separation instrument connected to the mass spectrometer. The method involves (i) in-situ spiking of the sample with isotopically enriched chromium species; (ii) separation of chromium species by precipitation with iron hydroxide; (iii) careful measurement of isotope ratios using an inductively coupled plasma mass spectrometer (ICP-MS) with a dynamic reaction cell (DRC) to remove isobaric polyatomic interferences. The method detection limits are 0.4 μg L⁻¹ for Cr(III) and 0.04 μg L⁻¹ for Cr(VI). The method is demonstrated for the speciation of Cr(III) and Cr(VI) in local nullah and synthetically spiked water samples. The percentage of conversion from Cr(III) to Cr(VI) increased from 5.9% to 9.3% with increase of the concentration of Cr(VI) and Cr(III) from 1 to 100 μg L⁻¹, while the reverse conversion from Cr(VI) to Cr(III) was observed within a range between 0.9% and 1.9%. The equilibrium constant for the conversion was found to be independent of the initial concentrations of Cr(III) and Cr(VI) and in the range of 1.0 (at pH 3) to 1.8 (at pH 10). The precision of the method is better than that of the DPC method for Cr(VI) analysis, with the added bonuses of freedom from interferences and simultaneous Cr(III) determination.     

Ionic liquid as a complexation and extraction medium combined with high-performance liquid chromatography in the evaluation of chromium(VI) and chromium(III) speciation in wastewater samples

A simple method has been proposed for the determination of chromium species by high-performance liquid chromatography (HPLC) after preconcentration by the ionic liquid, 1-butyl-3-methyimidazolium hexafluorophosphate ([C₄MIM][PF₆]). The simultaneous preconcentration of Cr(VI) and Cr(III) in wastewater was achieved with ammonium pyrrolidinedithiocarbamate (APDC) as the chelating agent and the ionic liquid [C₄MIM][PF₆] as the extractant. Baseline separation of the APDC chelates of Cr(III) and Cr(VI) was realised on a RP-C18 column using a mixture of methanol–acetonitrile–water (53:14:33, v/v) as the mobile phase at a flow rate of 1.0 mL min^{− 1}. The influences of several variables on the complexation and extraction were evaluated: pH, reaction time, APDC concentration and metal ion interference. Our results showed that when the linear concentration of Cr(VI) and Cr(III) ranged from 25 to 200 μg L^{− 1}, their linear correlation coefficients were between 0.9977 and 0.9978, their recoveries ranged from 91.8% to 95.8% and their relative standard deviations (n = 3) were between 0.31% and 1.8%. Common metal ions in water did not interfere with the determination. This method is a simple, fast, accurate, highly stable and selective method and has successfully been applied to the speciation of chromium in wastewater.     

A comprehensive study for selective removal of Cr(VI) by asymmetric imidazolium bromide salts as environmentally-friendly extractant

The study was to determine selective removal and recovery of Cr(VI) from acidic media by solvent extraction (SX) using asymmetric imidazolium-based room temperature imidazolium bromide salts (ARTILs) as the extractants. The relevant parameters on the extraction and the stripping of Cr(VI) were investigated to identify optimum conditions. The optimum conditions were determined as equilibration time 5 minutes, acid concentration and type 0.5?mol/L H₂SO₄, stirring speed 1200?rpm, extractant concentration and type 0.5?mol/L ARTIL5, phase ratio 2.0 and stripping reagent type, and concentration 2.0?mol/L NH₃. In optimum conditions, decyl substituted ARTIL was best in extraction process about 99.7% of extraction rate, whereas moderately hydrophobic pentyl substituted ARTIL was best in stripping process about 70.0% of stripping rate. Also, the optimized process was found as so selective toward Cr(VI) in the presence of the other metal ions with an environmental-friendly liquid–liquid–based SX method.     

On-line preconcentration and speciation analysis of Cr(III) and Cr(VI) using baker's yeast cells immobilised on controlled pore glass

A study was undertaken to evaluate Saccharomyces cerevisiae as a substrate for the biosorption of Cr(III) and Cr(VI) aiming to the selective determination of these species in aqueous solutions. The yeast cells were covalently immobilised on controlled pore glass (CPG), packed in a minicolumn and incorporated in an on-line flow injection system. The effect of chemical and physical variables affecting the biosorption process was tested in order to select the optimal analytical conditions for the Cr retention by S. cerevisiae. Cr(III) was retained by the immobilised cells and Cr(VI) were retained by CPG. The speciation was possible by selective and sequential elution of Cr(III) with 0.05 mol L⁻¹ HCl and 2.0 mol L⁻¹ HNO₃ for Cr(VI). The influence of some concomitant ions up to 20 mg L⁻¹ was also tested. Quantitative determinations of Cr were carried out by means of inductively coupled plasma optical emission spectrometry (ICP OES). Preconcentration factors of 12 were achieved for Cr(III) and 5 for Cr(VI) when 1.7 mL of sample were processed reaching detection limits of 0.45 for Cr(III) and 1.5 μg L⁻¹ for Cr(VI). The speciation of inorganic Cr in different kinds of natural waters was performed following the proposed method. Spiked water samples were also analysed and the recoveries were in all cases between 81 and 103%.     

Determination of Cr(III) and Cr(VI) in environmental waters by derivative flame atomic absorption spectrometry using flow injection on-line preconcentration with double-microcolumn adsorption

The species of Cr(III) and Cr(VI) in water samples were determined by flow injection on-line preconcentration and separation on two-microcolumn system-derivative flame atomic absorption spectrometry during a collaborative analysis for certification. The Cr(III) and Cr(VI) in water samples were retained on two microcolumns with ion exchange resin and were eluted directly to nebulizer by 15% HNO³ and 8% NH⁴NO³, respectively. The characteristic concentration (at the sensitivity grade of 2 mV min^?1 for 1 min of preconcentration time) for Cr(III) and Cr(VI) were 0.130 and 0.0985 μg l^?1, in the order which were 332- and 431-fold better than those of FAAS, and 45- and 47-fold better than those of FI-FAAS, respectively. The relative standard deviations were 3.27% and 3.66% with corresponding detection limits (3σ) of 0.244 and 0.235 μg l^?1, respectively. The linear ranges of determinations for Cr(III) and Cr(VI) were 0～100 μgm l^?1 with correlation coefficients of 0.9984 to 0.9996. The satisfactory recovery of 94.4%～106% for Cr(III) and Cr(VI) could be obtained from water samples.     

Neutron activation analysis for chromium(III) and (VI) in lixiviated liquid through a calcined chromium(VI) adsorbed hydrotalcite

Summary Electrophoresis followed by neutron activation analysis was utilized to determine chromium(III) and (VI) in mixed solutions. These solutions proceeded from Cr(VI) adsorbed hydrotalcites heated at 800 °C to partially immobilize Cr in the Mg-Al oxide solid solution. Immobilization was studied by Cr lixiviation with NaCl solutions through the heated hydrotalcites. The results have shown that Cr lixiviated was in the form of CrO₄^2- ions, mainly because some Cr(VI) was not completely reduced to Cr(III) during heating. Chromium lixiviated from HT-Cr sample, heated at 800 °C and γ-irradiated at 1000 kGys, was found, as well, in the form of CrO₄^2- ions. Although γ-irradiation increases Cr immobilization in the solid, it does not reduce completely all CrO₄^2- ions present in the solid and, therefore, some Cr is lixiviated through the solid in the form of CrO₄^2- ion.