共查询到20条相似文献,搜索用时 31 毫秒
1.
A simple layer‐by‐layer (LBL) assembly strategy was established for constructing a novel reagentless biosensor based on a nanocomposite of methylene blue multiwalled carbon nanotubes (MB‐MWNTs). A nanocomposite of MB‐MWNTs was obtained by direct premixing and possessed good dispersion in barbital‐HCl buffer. Through electrostatic interactions, the nanocomposite of MB‐MWNTs could alternately be assembled with horseradish peroxidase (HRP) on the Au electrode modified with precursor films. UV/Vis spectra and scanning electron microscopy (SEM) were applied to reveal the formation of the nanocomposite of MB‐MWNTs. The LBL assembly process was also verified by electrochemical impedance spectroscopy (EIS). The MB is a well‐established mediator and efficiently facilitated the electron shuttle between the HRP and the electrode, as demonstrated by the cyclic voltammetry (CV) measurements. The as‐prepared reagentless biosensor exhibited a fast response for the determination of hydrogen peroxide (H2O2) and reached 95% of the steady‐state current within 3 s. It was found that the linear response range of the reagentless biosensor for H2O2 was from 4.0 μM to 3.78 mM with a detection limit of 1.0 μM and a sensitivity of 22.5 μA mM−1. The biosensor exhibited a high reproducibility and stability. 相似文献
2.
The much‐enhanced electrochemical responses of potassium ferricyanide and methylene blue (MB) were firstly explored at the glassy carbon electrode modified with single‐walled carbon nanotubes (SWNT/GCE), indicating the distinct electrochemical activity of SWNTs towards electroactive molecules. A hydrophobic room temperature ionic liquid (RTIL), 1‐butyl‐3‐methylimidazolium hexafluorophosphate (BMIMPF6), was used as electrode modification material, which presented wide electrochemical windows, proton permeation and selective extraction ability. In consideration with the advantages of SWNTs and RTIL in detecting target molecules (TMs), a novel strategy of ‘sandwich–type’ electrode was established with TMs confined by RTIL between the SWNT/GCE and the RTIL membrane. The strategy was used for electrochemical detection of ascorbic acid (AA) and dopamine (DA), and detection limits of 400 and 80 fmol could be obtained, respectively. The selective detection of DA in the presence of high amount of AA could also be realized. This protocol presented many attractive advantages towards voltammetric detection of TMs, such as low sample demand, low cost, high sensitivity, and good stability. 相似文献
3.
Chemistry and Chemical Engineer School, Henan Institute of Science and Technology, Xinxiang, Henan 453003, China 相似文献
4.
A new modified carbon‐ceramic electrode was prepared by incorporating TiO2 nanoparticle into sol‐gel network by accompanying apple tissue. A mixture of fine graphite powder with 15 wt% of TiO2 nanoparticle was used for the preparation of the carbon matrix and finally modification with a known amount weighted of apple tissue. The apple tissue containing polyphenol oxidase enzyme acts as molecular recognition element. The electrocatalytic oxidation of dopamine was investigated on the surface of the nanobiocomposite modified carbon‐ceramic electrode using cyclic voltammetry, chronoamperometry and amperometry techniques. Effect of pH, scan rate, TiO2 percentage on the response of modified electrode was studied. The prepared modified electrode presented a linear range for dopamine from 5.0×10?6 to 1.2×10?3 M in buffered solutions with pH 7.4 by amperometry. The detection limit was 3.41×10?6 M dopamine. The response of the modified carbon‐ceramic electrode and unmodified carbon‐ceramic electrode was compared. 相似文献
5.
《Electroanalysis》2004,16(7):556-562
A new sol‐gel derived composite sensor has been developed for the determination of sulfite and sulfur dioxide using 3‐aminopropyltrimethoxysilane, ferrous sulfate and graphite powder by sol‐gel process. Cyclic voltammetry and amperometry studies revealed that the modified iron dispersed sol‐gel derived ceramic composite electrode exhibited excellent characteristics for the electrocatalytic oxidation of sulfite at a reduced potential of +0.35 V with good sensitivity and selectivity. The pH and the potential for sulfite estimation have been optimized. The sensor exhibited rapid and linear response to sulfite in the concentration range from 0.73 mg/L to 95.42 mg/L with a correlation coefficient of 0.997. The proposed sensor can be utilized for the determination sulfur dioxide after absorbing in a suitable medium and has promising characteristics such as, rapid response, good reproducibility and remarkable stability. 相似文献
6.
In the present work, an electrochemical sensor was developed for simple and sensitive determination of tryptophan (Trp) using multi‐walled carbon nanotubes modified sol‐gel electrode (MWCNTs/SGE). The electrocatalytic oxidation of tryptophan was investigated by cyclic voltammetry (CV) and differential pulse voltammetry (DPV). It was found that the oxidation peak current of Trp at the MWCNTs/SGE was greatly improved compared with that of the bare SGE. Furthermore, at the MWCNTs/SGE, the anodic peak potential of Trp is shifted about 220 mV to more negative value indicated that modified electrode has better electrocatalytic activity for electro‐oxidation of Trp. The anodic peak currents increased linearly with the concentration of tryptophan in the range of 0.2 × 10?6 to 15 × 10?6 M with a detection limit of 0.139 × 10?6 M (at an S/N = 3). 相似文献
7.
A nanocomposite gel with a uniform porous structure and well‐controlled compositions prepared by mixing three‐dimensional graphene material with an ionic liquid, 1‐butyl‐3‐methylimidazolium hexafluorophosphate, is used for nitric oxide detection. It shows a fast response of less than 4 seconds, an excellent sensitivity of 11.2 µA cm−2 (µmol/L)−1 and an extremely low detection limit of 16 nM with a signal‐to‐noise ratio of 3 (S/N=3), a performance superior to that of reported works based on carbon nanotubes and nanoparticles. The high sensitivity is attributed to the large electroactive surface area of the graphene gel nanocomposite towards nitric oxide oxidation. The electrochemical behavior of the gel nanocomposite is investigated and explained. 相似文献
8.
《Biomedical chromatography : BMC》2017,31(8)
Electrochemically co‐deposited sol–gel/Cu nanocomposites have been introduced as a novel, simple and single‐step technique for preparation of solid‐phase microextraction (SPME) coating to extract methadone (MDN) (a synthetic opioid) in urine samples. The porous surface structure of the sol–gel/Cu nanocomposite coating was revealed by scanning electron microscopy. Direct immersion SPME followed by HPLC‐UV determination was employed. The factors influencing the SPME procedure, such as the salt content, desorption solvent type, pH and equilibration time, were optimized. The best conditions were obtained with no salt content, acetonitrile as desorption solvent type, pH 9 and 10 min equilibration time. The calibration graphs for urine samples showed good linearity. The detection limit was about 0.2 ng mL−1. Also, the novel method for preparation of nanocomposite fiber was compared with previously reported techniques for MDN determination. The results show that the novel nanocomposite fiber has relatively high extraction efficiency. 相似文献
9.
An organic‐inorganic composite electrode was prepared by the sol‐gel method. For this purpose the carbon composite electrode (CCE) was modified with copper hexacyanoferrate (CuHCF). The CuHCF‐CCE was prepared by two methods. In one method CCE was prepared in one step and in another method the electrode was prepared in a two‐step process. The electrochemical behavior of the CuHCF modified electrode was studied by cyclic voltammetry; the modified electrode shows a pair of peaks with a surface‐confined characteristic in a 0.1 M phosphate buffer (pH 7) with K+ cation, as a supporting electrolyte. The CuHCF‐CCE showed electrocatalytic activity toward oxidation of Dopamine (DA). The kinetics of the catalytic reaction was investigated by using chronoamperometry. The average value of the rate constant for catalytic reaction and the diffusion coefficient were calculated. At a 0.85 V potential under hydrodynamic conditions (stirred solution), the oxidation current is proportional to the dopamine concentration, and the calibration plot was linear over the concentration range of 5‐85 μM. 相似文献
10.
Zhijie Wang Mathieu Etienne Sascha Pöller Wolfgang Schuhmann Gert‐Wieland Kohring Victor Mamane Alain Walcarius 《Electroanalysis》2012,24(2):376-385
Multiwalled carbon nanotubes (MWCNT) have been functionalized, for the electrocatalytic detection of NADH, by microwave treatment, electrochemical deposition of poly(methylene green) or wrapping with an Os‐complex modified polymer. Sol‐gel thin films have been then electrodeposited on the carbon nanotube layers for co‐immobilization of D ‐sorbitol dehydrogenase and diaphorase when necessary and NAD+ via covalent linkage using glycidoxypropyltrimethoxysilane. The comparison of these systems shows that the electrodeposited sol‐gel matrix can significantly affect the operational behavior of functionalized MWCNT. Only MWCNT wrapped with the Os‐complex modified polymer and covered with a sol‐gel biocomposite allowed the electrochemical detection of D ‐sorbitol in a reagentless configuration. 相似文献
11.
《Electroanalysis》2003,15(7):608-612
A new type of organically modified sol‐gel/chitosan composite material was developed and used for the construction of glucose biosensor. This material provided good biocompatibility and the stabilizing microenvironment around the enzyme. Ferrocene was immobilized on the surface of glassy carbon electrode as a mediator. The characteristics of the biosensor were studied by cyclic voltammetry and chronoamperometry. The effects of enzyme‐loading, buffer pH, applied potential and several interferences on the response of the enzyme electrode were investigated. The simple and low‐cost glucose biosensor exhibited high sensitivity and good stability. 相似文献
12.
The sol‐gel technique was used to construct tin pentacyanonitrosylferrate (SnPCNF) modified composite carbon ceramic electrode (CCE). This involves two steps: construction of CCE containing metallic Sn powder and then electrochemical creating of SnPCNF on the surface of CCE. The SnPCNF modified CCE (SnPCNFlCCE) was characterized by energy‐dispersive X‐ray (EDX), FTIR and cyclic voltammetry (CV) techniques. The SnPCNF film showed electrocatalytic activity toward the oxidation of L ‐cysteine. A linear calibration plot was obtained over the L ‐cysteine concentration range 1–51 μM using chronoamperometry. L ‐cysteine was determined amperometrically at the surface of this modified electrode. The detection limit (for a signal to noise of 3) and sensitivity were found to be 0.62 μM and 126 μA/mM, respectively. 相似文献
13.
The direct bioelectrocatalysis was demonstrated for pyrroloquinoline quinone‐dependent glucose dehydrogenase (PQQ‐dependent GDH) covalently attached to single‐walled carbon nanotubes (SWNTs). The homogeneous ink‐like SWNT suspension was used for both creating the SWNT network on the microelectrode carbon surface and for enzyme immobilization. Functionalization of the SWNT surface by forming active ester groups was found to considerably enhance SWNT solubility in water with a range from 0.1 to 1.0 mg/mL. The PQQ‐dependent GDH immobilized on the surface of the SWNTs exhibited fast heterogeneous electron transfer with a rate constant of 3.6 s?1. Moreover, the immobilized PQQ‐dependent GDH retained its enzymatic activity for glucose oxidation. A fusion of PQQ‐dependent GDH with SWNTs has a great potential for the development of low‐cost and reagentless glucose sensors and biofuel cells. 相似文献
14.
Xiao Li Kun‐Feng Zhou Zhi‐Bo Tong Xi‐Ya Yang Cui‐Ying Chen Xue‐Hui Shang Jing‐Quan Sha 《化学:亚洲杂志》2019,14(19):3424-3430
To increase the conductivity of polyoxometalate‐based metal–organic frameworks (POMOFs) and promote their applications in the field of energy storage, herein, a simple approach was employed to improve their overall electrochemical performances by introducing a functionalized single‐walled carbon nanotubes (SWNT‐COOH). A new POMOF compound, [Cu18(trz)12Cl3(H2O)2][PW12O40] (CuPW), was successfully synthesized, then the size‐matched functionalized SWNT–COOH was introduced to fabricate CuPW/SWNT–COOH composite (PMNT–COOH) by employing a simple sonication‐driven periodic functionalization strategy. When the PMNT–COOH nanocomposite was used as the anode material for Lithium‐ion batteries (LIBs), PMNT–COOH( 3 ) (CuPWNC:SWNT‐COOH=3:1) showed superior behavior of energy storage, a high reversible capacity of 885 mA h g?1 up to a cycle life of 170 cycles. The electrochemical results indicate that the uniform packing of SWNT–COOH provided a favored contact between the electrolyte and the electrode, resulting in enhanced specific capacity during lithium insertion/extraction process. This fabrication of PMNT–COOH nanocomposite opens new avenues for the design and synthesis of new generation electrode materials for LIBs. 相似文献
15.
A novel nanocomposite of quinone‐amine polymer and multiwalled carbon nanotubes was synthesized from iodate‐oxidation/Michael addition reaction of 1,2‐dihydroxybenzene with o‐phenylenediamine, which was characterized by TEM, FTIR and UV‐vis spectra. The nanocomposite modified Au electrode with well‐defined quinone redox peaks effectively mediated the oxidation of NADH in pH 7.0 phosphate buffer, with an overpotential decrease by ca. 470 mV (vs. bare Au), a limit of detection of 6.4 nmol L?1 and good antiinterferent ability. 相似文献
16.
A new sol‐gel carbon composite electrode using hexacyanoferrate (HCF)‐Th(IV) ion pair as a suitable modifier is fabricated in the present study. The Th(IV)‐HCF‐sol‐gel carbon composite electrode (THCF‐CCE) has been prepared by mixing methyl trimethoxysilan (MTMOS) sol‐gel precursor and carbon powder with ion pair and then to fix in a plastic tube. Cyclic voltammetry and chronoamperometry were employed to study the electrochemical and electrocatalytic properties of proposed electrode. The apparent charge transfer rate constant, ks, and transfer coefficient, α, for electron transfer between ion‐pair and sol‐gel CPE were calculated as 3.10 ± 0.10 s?1 and 0.52, respectively. The THCF‐CCE showed a significant electrocatalytic activity towards oxidation of ascorbic acid (AA) and dopamine (DA) in 0.1 M acidic phosphate buffer solutions (pH 3) containing KCl as a supporting electrolyte. The mean value of the diffusion coefficients for ascorbic acid and dopamine were found 4.12 × 10?5 and 4.43 × 10?5 (cm2s?1), respectively. High stability, good reproducibility, rapid response, easy surface regeneration and fabrication are the important characteristics of the proposed sensor. The resulting peaks from the electrocatalytic oxidation of AA and DA were well resolved with good sensitivity. A linear response was observed for AA and DA in the concentration range of 1 × 10?5 to 3 × 10?3 M and 4 × 10?6 to 2.2 × 10?4 M, respectively. 相似文献
17.
A simple approach for the preparation of emitter of electrospray ionization mass spectrometry by covalently coating the fused‐silica capillary tip with the conductive carbon‐nanotube sol‐gel composite material (CNTSCM) is described. The CNTSCM was prepared by dispersing single‐walled carbon nanotubes in the sol composed of a mixture of 3‐glycidoxypropyltrimethoxysilane and 3‐aminopropyltrimethoxysilane, and ethanol. The long‐term stability of the prepared ESI emitters was demonstrated by at least 180 h of continuous use. Signal intensity obtained by the prepared emitter was mass‐flux sensitive when the flow rate was lower than 500 nL/min, while the signal intensity performed a concentration dependence when the flow rate was in the range of 500–800 nL/min. The usefulness of such a prepared emitter was demonstrated by the analysis of various types of samples such as organic small molecular drugs, oligosaccharide, peptide, and protein. 相似文献
18.
Single-wall carbon nanotubes(SWNTs) modified gold electrodes were prepared by using two different methods.The electrochemical behavior of cytochrome c on the modified gold electrodes was investigated.The first kind of SWNT-modified electrode (noted as SWNT/Au electrode)was prepared by the adsorption of carboxylterminated SWNTs from DMF dispersion on the gold electrode.The oxidatively processed SWNT tips were covalently modified by coupling with amines (AET) to form amide linkage.Via Au-S chemical bonding,the self-assembled monolayer of thiol-unctionalized nanotubes on gold surface was fabricated so as to prepare the others SWNT-modified electrode (noted as SWNT/AET/Au electrode).It was shown from cyclic voltammetry cxperiments that cytochrome c exhibited direct electrochemical responses on the both electrodes, but only the current of controlled diffusion existed on the SWNT/Au electrode while both the currents of controlled diffusion and adsorption of cytochrome c occurred on the SWNT/AET/Au electrode.Photoelastic Modulation Infared Reflection Absorpthion Spectroscopy (PEM-IRRAS) and Quartz Crystal Microbalance (QCM) were employed to verify the adsorption of SWNTs on the gold electrodes.The results proved that SWNTs could enhance the direct electron transfer proecss between the electrodes and redox proteins. 相似文献
19.
A new carbon nanotubes modified electrode (poly‐Nq‐MWCNTs/GCE) was fabricated by electropolymerization of 1,2‐naphththoquinone to the surface of multi‐walled carbon nanotubes modified electrode by casting method. The morphology of the nanocomposite was characterized by scanning electron microscopy. Cyclic voltammetry and chronoamperometry were applied to investigate the electrochemical properties of the poly‐Nq‐MWCNTs nanocomposite modified electrode. The result of electrochemical experiments showed that such modified electrode had a favorable catalytic ability to oxidation of β‐nicotinamide adenine dinucleotide (NADH). The resulted sensor was sensitiveness to NADH and achieved 95β of the steady‐state current within 5s. Furthermore, the anodic peak current was linear to the concentration of NADH for the range from 1.0 μM to 0.14 mM. The linear equation was: I(μA) = 0.3987 + 0.1035c (μmol/L), the correlation coefficient r = 0.9962, the detect limit is down to 1 × 10?7 M (S/N = 3) and the sensitivity is 0.1035 μA/mmol. The well catalytic activity of the sensor was ascribed to the synergistic effect role played by MWCNTs and poly‐Nq. Moreover, the based sensor possesses good stability and reproducibility. 相似文献
20.
《Electroanalysis》2006,18(21):2129-2136
A sol‐gel technique was used here to prepare a renewable carbon ceramic electrode modified with nickel powder. Cyclic voltammograms of the resulting modified electrode show stable and a well defined redox couple due to Ni(II)/Ni(III) system with surface confined characteristics. The modified electrode shows excellent catalytic activity toward L ‐cystine, L ‐cysteine and L ‐methionine oxidation at reduced overpotential in alkaline solutions. In addition the antifouling properties at the modified electrode toward the above analytes and their oxidation products increases the reproducibility of results. L ‐cystine, L ‐cysteine and L ‐methionine were determined chronoamperometricaly at the surface of this modified electrode at pH range 9–13. Under the optimized conditions the calibration curves are linear in the concentration range 1–450 μM, 2–90 μM and 0.2–75 μM for L ‐cystine, L ‐methionine and L ‐cysteine determination, respectively. The detection limit and sensitivity were 0.64 μM, 3.8 nA/ μM for L ‐cystine, 2 μM, 5.6 nA/ μM for L ‐methionine and 0.2 μM and 8.1 nA/μM for L ‐cysteine. The advantageous of this modified electrode is high response, good stability and reproducibility, excellent catalytic activity for oxidation inert molecules at reduced overpotential and possibility of regeneration of the electrode surface by potential cycling for 5 minutes. Furthermore, the modified electrode has been prepared without using specific reagents. This sensor can be used as an amperometric detector for disulfides detection in chromatographic or flow systems. 相似文献