Electroless deposition of copper on polyimide films modified by surface graft copolymerization with nitrogen-containing vinyl monomers

Surface modification of Ar-plasma-pretreated polyimide (PI) films (Kapton® HN films) via UV-induced graft copolymerization with 1-vinylimidazole (VIDz), 4-vinylpyridine (4VP), and 2-vinylpyridine (2VP) under atmospheric conditions was carried out to improve their adhesion with the electrolessly deposited Cu. The surface compositions of the graft-copolymerized PI films were characterized by X-ray photoelectron spectroscopy. The adhesion strength of the electrolessly deposited Cu on the surface-graft-copolymerized PI film was affected by the type of monomers used for graft copolymerization and the graft concentration. T-peel adhesion strengths of about 15, 10, and 6?N/cm were obtained for the Cu/graft-modified PI assemblies involving, respectively, the VIDz, 4VP, and 2VP graft-copolymerized PI films. These adhesion strengths are much higher than those obtained for assemblies involving electrolessly deposited Cu on pristine or on Ar-plasma-treated PI films. The adhesion strengths involving the VIDz and 4VP surface-graft-copolymerized PI films are also higher than those involving PI films modified by chemical etching. The cohesive failure inside the PI substrate of the Cu/graft-modified PI assemblies during delamination suggested that not only were the grafted polymer chains covalently tethered on the PI film, they were also incorporated into the metal matrix during the electroless plating process.     

Influence of bath temperatures on the wettability of copper films surface prepared by electroless plating method on beech wood

Copper films were coated on beech wood substrates by electroless plating method. The influence of bath temperature on the copper films properties was studied by varying the bath temperatures 25, 35, 45 and 55 °C. Scanning electron microscopy (SEM) equipped with energy dispersive spectroscopy (EDS), X‐ray diffraction (XRD) pattern, X‐ray photoelectron spectroscopy (XPS), micro Raman spectroscopy and contact angle measurements were used to both characterize the physical and chemical copper films properties and understand the influence of bath temperature on the wettability of copper surface. In our studies, we have found that the gained copper mass significantly increased at 55 °C. The crystalline nature of the coated copper was confirmed by XRD. The presence of Cu₂O and CuO was observed by XPS and micro Raman techniques, which confirms the oxidization of the coated copper surface. Also these characterization techniques have shown the big influence of bath temperature on the morphology, grain size, chemical composition and the film thickness of the coated copper. The wettability was highly influenced by increasing CuO on the coated copper, which is increased by the bath temperature. The contact angle measurements have demonstrated the influence of C―O, O―C?O and CuO components of the surface on the wettability of the samples. Copyright © 2016 John Wiley & Sons, Ltd.     

Electrically conductive acrylonitrile–butadiene rubber elastomers prepared by dopamine‐induced surface functionalization and metallization

A novel method for the preparation of electrical conductive surface silvered acrylonitrile–butadiene rubber (NBR) was developed. Dopamine was spontaneously oxide polymerized and deposited onto the surface of NBR. Electroless plating of silver was carried out on the poly(dopamine) (PDA)‐functionalized NBR surface. The composition of the NBR surface was studied by X‐ray photoelectron spectroscopy (XPS). XPS results showed that PDA was successfully deposited onto the NBR surface. The morphology of the NBR surface was observed by scanning electron microscopy (SEM). The SEM images showed that PDA had formed a distinctive layer ready for electroless deposition of silver. The catechol/quinone groups on the PDA molecular structure can be used as binding sites for silver ions. The silvered NBR showed high surface conductivity of 1.4 Ω. Copyright © 2011 John Wiley & Sons, Ltd.     

Surface modification of plasma‐pretreated expanded poly (tetrafluroethylene) films by graft copolymerization

A two‐step process based on a low‐pressure helium plasma treatment followed by acrylic acid‐grafting copolymerization was used for the surface modification of expanded polytetrafluoroethylene (ePTFE) films. The effects of plasma treatment power and treatment time on the hydrophilicity of the film surface were investigated. The wettability of the ePTFE film surface was characterized by water contact angle, and the surface compositions of the untreated and treated ePTFE samples were evaluated by atomic force microscopy and XPS. Contact angle measurements revealed that the hydrophilicity of the ePTFE film surface was greatly enhanced by the combined actions of the plasma treatment and acrylic acid grafting, and the contact angle decreased from 145° to 66°. Atomic force microscopy analyses showed that the surface roughness increased after the plasma treatment. XPS analyses showed substantial increase in the concentration of carbon and oxygen atoms and a decrease in the concentration of fluorine atoms at the film surface. T‐peel strength showed an improved bonding strength between the film and an adhesive tape after the treatment. Copyright © 2012 John Wiley & Sons, Ltd.     

Oxidation of polyethylene surface by glow discharge and subsequent graft copolymerization of acrylic acid

Plasma-induced graft copolymerization of acrylic acid, which was incorporated into PE films, was investigated here. The influence of plasma conditions such as plasma treatment gases, power, pressure, time, monomer concentration, and graft copolymerization time on polymerization yield was determined. The samples were characterized by ESCA, IR, and water contact angle. A respective chemical shift of the C1s signal of Ar or O₂ plasmatreated and untreated PE films was revealed by ESCA, in which the presence of the grafted PAAc was also verified. An increase in polymerization yield with plasma treatment duration and power was found. That the grafted copolymerization was limited to a very thin surface region was revealed by optical microscopy on the cross section of the grafted film. © 1993 John Wiley & Sons, Inc.     

Surface modification and adhesion characteristics of polycarbonate films after graft copolymerization

The surfaces of ozone-pretreated polycarbonate films were subjected to further modification by thermally induced graft copolymerization with acrylic acid (AAc), sodium salt of styrene sulfonic acid (NaSS), N,N-dimethylacrylamide (DMAA), N,N-(dimethylamino)ethyl methacrylate (DMAEMA) and 3-dimethyl(methacryloyl ethyl)-ammonium propanesulfonate (DMAPS) monomers. The structure and composition at the copolymer interface were studied by angle-resolved X-ray photoelectron spectroscopy (XPS). For polycarbonate films with a substantial amount of grafted polymer, the hydrophilic graft penetrates or becomes partially submerged beneath a thin surface layer of dense substrate chains. This microstructure was further supported by the water contact angle measurements. Adhesive-free adhesion studies revealed that the AAc, DMAA or DMAPS graft copolymerized polycarbonate film surface adhered strongly to another similarly modified surface (homo-interface) when brought into direct contact in the presence of water and subsequently dried. The development of the lap shear strength is dependent on the concentration of the surface graft, the microstructure of the grafted surface, the adhesion (drying) time, and the nature of the interfacial interaction. The simultaneous presence of chain entanglement and electrostatic interaction readily results in substantially enhanced adhesion strengths between two DMAPS graft copolymerized surfaces or between an AAc and a DMAA graft copolymerized surface (hetero-interface). XPS analyses of the delaminated surfaces suggest that failure occurred cohesively below the graft-substrate interface. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 357–366, 1998     

Lignin‐based polymers via graft copolymerization

Lignin is an important source of synthetic materials because of its abundance in nature, low cost, stable supply, and no competition to the human food supply. Lignin, a cross‐linked phenolic polymer, contains a large number of aromatic groups that can be used as a substitute for petroleum‐based aromatic fine chemicals. However, modification of lignin is necessary for its application in advanced materials due to its chemically inert nature and structural complexity. Polymeric modification of lignin via graft copolymerization represents an important avenue for modification because this method forms stable covalent bond linkages between lignin and synthetic functional polymers. In this review, we discuss recent synthetic strategies toward polymeric modification of lignin using graft copolymerization and the special properties and applications of the produced lignin copolymers. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3515–3528     

Cation-exchange fabric prepared by electron beam-induced graft copolymerization of binary monomer mixture

Applying the electron-beam preirradiation method in air the cation - exchange fabric (CEF) containing sulfonic acid (R-SO₃H) groups was prepared by graft copolymerization of sodium styrenesulfonate with acrylic acid onto non woven polypropylene fabric. The effect of reaction conditions on the grafting yield and reaction mechanism was examined. The ion-exchange properties towards Cu(II) and Co(II) ions of the CEF were investigated depending on the form of the CEF and a pH of the solution. It was found that the synthesized CEF contains both strong acid groups (R-SO₃H) and weak acid (R-COOH) groups in almost equal proportion. The utilization of the CEF in Na₊ form allows to make the best use of its ion-exchange capacity.     

Electroless plating of copper on Si(100) surfaces modified by surface‐initiated atom‐transfer radical polymerization of 4‐vinylpyridine

Surface‐initiated atom‐transfer radical polymerization (ATRP) of 4‐vinylpyridine (4VP) on a pretreated Si(100) surface was carried out. The composition and topography of the Si(100) surface modified by poly(4‐vinylpyridine) (P4VP) were characterized by XPS and atomic force microscopy (AFM), respectively. The P4VP layer on the Si(100) surface was used not only as chemisorption sites for the palladium complexes without prior sensitization by SnCl₂ solution during the electroless plating, but also as an adhesion promotion layer for the electrolessly deposited copper. The electrolessly deposited copper on the Si–P4VP surface exhibited a 180° peel adhesion strength above 6 N/cm. The adhesion strength was much higher than that of the electrolessly deposited copper to the pristine silicon surface. Copyright © 2008 John Wiley & Sons, Ltd.     

Potassium diperiodatonickelate‐initiated graft copolymerization of methyl acrylate onto organophilic montmorillonite

Using potassium diperiodatonickelate (Ni (IV)) as an efficient initiator, the graft copolymerization of methyl acrylate (MA) onto organophilic montmorillonite (OMMT) was successfully performed in an alkaline medium. Three grafting parameters were systematically evaluated as functions of the temperature, the initiator concentration, reaction time, pH value, and the ratio of MA to OMMT substrate. The structure of the titled graft copolymers (OMMT‐g‐PMA) were confirmed by Fourier transform infrared spectroscopy (FTIR), X‐ray diffraction (XRD), differential scanning calorimetry (DSC), and thermo‐gravimetric analysis (TGA). It was found that Ni (IV) was a highly efficient initiator for graft copolymerization of the MA onto OMMT, i.e., grafting efficiency is as high as 95% and grafting percentage can be facilely controlled within 700% in this study. In addition, the highest grafting efficiency and grafting percentage were obtained when temperature adopted was over 40°C and pH was about 10.3. A single‐electron‐transfer mechanism was proposed to illustrate the formation of radicals and the initiation reaction. Copyright © 2008 John Wiley & Sons, Ltd.     

Nanostructure,interactions, and conductivities of polymer electrolytes comprising silver salt and microphase‐separated graft copolymer

Silver polymer electrolytes were prepared by blending silver salt with poly(oxyethylene)₉ methacrylate)‐graft‐poly(dimethyl siloxane), POEM‐g‐PDMS, confining silver salts within the continuous ion‐conducting POEM domains of microphase‐separated graft copolymer. AgClO₄ polymer electrolytes exhibited their maximum conductivity at high silver concentrations as well as higher ionic conductivities than AgCF₃SO₃ electrolytes. The difference in conductivities of the two electrolytes was investigated in terms of the differences in the interactions of silver ions with ether oxygen of POEM and, hence, with the anions of salts. Upon the addition of salt in graft copolymer, the increase of T_g in AgClO₄ was higher than that in AgCF₃SO₃ electrolytes. Analysis of an extended configuration entropy model revealed that the interaction of ether oxygen/AgClO₄ was stronger than that of ether oxygen/AgCF₃SO₃ whereas the interaction of Ag⁺/ClO₄^? was weaker than that of Ag⁺/CF₃SO₃^?. These interactions are supported by the anion vibration mode of FT‐Raman spectroscopy. It is thus concluded that the higher ionic conductivity of AgClO₄ electrolytes was mostly because of higher concentrations of free ions, resulting from their strong ether oxygen/silver ion and weak silver ion/anion interactions. A small angle X‐ray scattering study also showed that the connectivity of the POEM phase was well developed to form nanophase morphology and the domain periodicities of graft copolymer electrolytes monotonically increased with the increase of silver concentration up to critical concentrations, after which the connectivity was less developed and the domain spacings remained invariant. This is attributed to the fact that silver salts are spatially and selectively incorporated in conducting POEM domains as free ions up to critical concentrations, after which they are distributed in both domains as ion pairs without selectivity. The increase of domain d‐spacing in AgClO₄ electrolytes was larger than that in AgCF₃SO₃, which again results from high concentrations of free ions in the former. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1018–1025, 2007     

Preparation and thermal treatment of Pd/Ag composite membrane on a porous alumina tube by sequential electroless plating technique for H2 separation

Pd/Ag/α-Al2O3 composite membranes were prepared by sequential electroless plating technique. The prepared membranes were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, energy dispersive spectroscopy, and inductively coupled plasma atomic emission spectroscopy techniques （ICP-AES）. Effects of annealing time, Ag content, and air treatment on the hydrogen permeation flux and morphology of the alloys were investigated. The results of the investigation showed that the prepared type of tube had a good potential as substrate for membrane preparation. In addition, a uniform defect-free alloy was prepared by annealing at 550 ℃ in H2 atmosphere. The permeation results showed an increase in H2 permeation flux by increasing the Ag content and the annealing time. In addition, the air treatment of the prepared membranes at 400 ℃ for 1 h changed the morphology of the alloy and substantially enhanced the hydrogen flux.     

Kinetics of graft copolymerization of methyl methacrylate onto polychloroprene with tricaprylylmethylammonium chloride as a phase‐transfer catalyst

The phase‐transfer catalyzed graft copolymerization of methyl methacrylate onto polychloroprene was carried out using tricaprylylmethylammonium chloride as a phase‐transfer catalyst in a two‐phase system of an aqueous Na₂S₂O₈ solution and toluene at 55 °C under a nitrogen atmosphere. The initial rate of graft copolymerization was expressed as the combined terms of quaternary onium cation and peroxydisulfate anion in the aqueous phase rather than the fed concentrations of catalyst and Na₂S₂O₈. The observed initial rate of graft copolymerization was used to analyze the graft copolymerization mechanism with a cycle phase‐transfer initiation step in the heterogeneous liquid–liquid system. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3543–3549, 2000     

Gas transport properties of asymmetric polyimide membranes prepared by ion‐beam irradiation

Ion beam irradiation has been widely used to modify the structure and properties of membrane surface layers. In this study, the gas permeability and selectivity of an asymmetric polyimide membrane modified by He ion irradiation were investigated using a high vacuum apparatus equipped with a Baratron absolute pressure gauge at 76 cmHg and 35 °C. Specifically, we estimated the effects of the gas diffusion and solubility on the gas permeation properties of the asymmetric membranes with the carbonized skin layer prepared by ion irradiation. The asymmetric polyimide membranes were prepared by a dry–wet phase inversion process, and the surface skin layer on the membrane was irradiated by He ions at fluences of 1 × 10¹⁵ to 5 × 10¹⁵ ions/cm² at 50 keV. The increase in the gas permeability of the He⁺‐irradiated asymmetric polyimide membrane is entirely due to an increase in the gas diffusion, and the gas selectivity increases of the membranes were responsible for the high gas diffusion selectivities. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 262–269, 2007.     

Preparation and dielectric properties of polyimide/silica nanocomposite films prepared from sol–gel and blending process

Using poly(amic acid) (PAA) as a precursor followed by thermal imidization, the polyimide/silica nanocomposite films were prepared via an improved sol–gel process and a blending process, respectively. FT‐IR, TEM and TGA measurements were used to characterize the structure and properties of the obtained films. The results confirmed that the introduction of silica did not yield negative effects on the conversion of the PAA precursor to the polyimide. With the increase of silica content, the aggregation of silica appeared in the polyimide matrix, and the thermal stability decreased slightly for both kinds of films. The dielectric constant (ε) of both films increased slowly with the increase of the silica concentration. The dielectric constant of the obtained polyimide/silica nanocomposite films displayed good stability within a wide range of temperatures or frequency. Based on modeling relation between ε and silica content, the difference in dielectric properties for two kinds of nanocomposites are discussed. Copyright © 2007 John Wiley & Sons, Ltd.     

Photoreactive nanomatrix structure formed by graft‐copolymerization of 1,9‐nonandiol dimethacrylate onto natural rubber

Formation of photoreactive nanomatrix structure was investigated by graft‐copolymerization of an inclusion complex of 1,9‐nonandiol dimethacrylate (NDMA) with β‐cyclodextrin (β‐CD) onto natural rubber particle using potassium persulfate (KPS), tert‐butyl hydroperoxide/tetraethylenepentamine (TBHPO/TEPA), cumene hydroperoxide/tetraethylenepentamine (CHPO/TEPA), and benzoyl peroxide (BPO) as an initiator. The graft copolymer was characterized by ¹H NMR and FTIR after coagulation. The conversion of NDMA and the amount of residual methacryloyl group were found to be 58.5 w/w % and 1.81 w/w %, respectively, under the suitable condition of the graft‐copolymerization. The morphology of the film specimen, prepared from the graft copolymer, was observed by transmission electron microscopy (TEM) after staining the film with OsO₄. Natural rubber particle of about 1.0 μm in diameter was dispersed in poly(NDMA) matrix of about 10 nm in thickness. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2418–2424, 2010     

Preparation of a copolymer of methyl methacrylate with a new monomer, 2,2,6,6‐tetramethyl‐4‐benzyloxyl‐piperidinyl methacrylate,and its initiation of the graft copolymerization of styrene with a controlled radical mechanism

A copolymer [P(MMA‐co‐TBPM)] was prepared by the radical polymerization of methyl methacrylate (MMA) and 2,2,6,6‐tetramethyl‐4‐benzyloxyl‐piperidinyl methacrylate (TBPM) with azobisisobutyronitrile as an initiator. TBPM was a new monomer containing an activated ester. Both the copolymer and TBPM were characterized with NMR, IR, and gel permeation chromatography in detail. It was confirmed that P(MMA‐co‐TBPM) could initiate the graft polymerization of styrene by the cleavage of the activated ester of the TBPM segment. This process was controllable, and the molecular weight of the graft chain of polystyrene increased with the increment of conversion. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4398–4403, 2002     

Structure and properties of polyimide films during a far‐infrared‐induced imidization process

The conversion of poly(amic acid) into polyimide (PI) was achieved with far‐infrared radiation (FIR) and conventional thermal treatments. The structure and properties of PI films during different stages of imidization were studied with Fourier transform infrared spectroscopy, weight‐loss analysis during imidization, tensile property measurements, and dynamic mechanical thermal analysis. The effects of the imidization degree, postimidization, and solvent on the thermal and mechanical properties of PI films were quantitatively investigated. The corresponding structural changes were also examined. The experimental results showed that the imidization process proceeded more quickly and more completely in an FIR oven than in a conventional oven. A prolonged FIR treatment at a lower temperature (25–100 °C) accelerated the imidization process. The tensile stress–strain curves had a fanlike distribution with the development of the FIR imidization process and a fishtail distribution with conventional thermal imidization. During FIR imidization, the best tensile properties were obtained at 340 °C, and thermooxidative degradation occurred at about 420 °C. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2490–2501, 2004     

Thermo- and pH-responsive polypropylene microporous membrane prepared by the photoinduced RAFT-mediated graft copolymerization

Thermo- and pH-responsive polypropylene microporous membrane prepared by photoinduced reversible addition–fragmentation chain transfer (RAFT) graft copolymerization of acrylic acid and N-isopropyl acrylamide by using dibenzyltrithiocarbonate as a RAFT agent. Attenuated total reflection-Fourier transform infrared spectroscopy (ATR/FT-IR), X-ray photoelectron spectroscopy (XPS) and field emission scanning electron microscopy (FE-SEM) were used to characterize the structural and morphological changes on the membrane surface. Results of ATR/FT-IR and XPS clearly indicated that poly(acrylic acid) (PAAc) and poly(N-isopropyl acrylamide) (PNIPAAm) were successfully grafted onto the membrane surface. The grafting chain length of PAAc on the membrane surface increased with the increase of UV irradiation time, and decreased with the increase of the concentration of chain transfer agent. The PAAc grafted membranes containing macro-chain transfer agents, or the living membrane surfaces were further functionalized via surface-initiated block copolymerization with N-isopropyl acrylamide in the presence of free radical initiator, 2,2′-azobisisobutyronitrile. It was found that PNIPAAm can be grafted onto the PAAc grafted membrane surface. The results demonstrated that polymerization of AAc and NIPAAm by the RAFT method could be accomplished under UV irradiation and the process possessing the living character. The PPMMs with PAAc and PNIPAAm grafting chains exhibited both pH- and temperature-dependent permeability to aqueous media.