Simultaneous Determination of Hydroquinone and Catechol at a Glassy Carbon Electrode Modified with Multiwall Carbon Nanotubes

A simply and high selectively electrochemical method for simultaneous determination of hydroquinone and catechol has been developed at a glassy carbon electrode modified with multiwall carbon nanotubes (MWNT). It was found that the oxidation peak separation of hydroquinone and catechol and the oxidation currents of hydroquinone and catechol greatly increase at MWNT modified electrode in 0.20 M acetate buffer solution (pH 4.5). The oxidation peaks of hydroquinone and catechol merge into a large peak of 302 mV (vs. Ag/AgCl, 3 M NaCl) at bare glassy carbon electrode. The two corresponding well‐defined oxidation peaks of hydroquinone in the presence of catechol at MWNT modified electrode occur at 264 mV and 162 mV, respectively. Under the optimized condition, the oxidation peak current of hydroquinone is linear over a range from 1.0×10^?6 M to 1.0×10^?4 M hydroquinone in the presence of 1.0×10^?4 M catechol with the detection limit of 7.5×10^?7 M and the oxidation peak current of catechol is linear over a range from 6.0×10^?7 M to 1.0×10^?4 M catechol in the presence of 1.0×10^?4 M hydroquinone with the detection limit of 2.0×10^?7 M. The proposed method has been applied to simultaneous determination of hydroquinone and catechol in a water sample with simplicity and high selectivity.     

Simultaneous Square‐Wave Voltammetric Determination of Paracetamol,Caffeine and Orphenadrine in Pharmaceutical Formulations Using a Cathodically Pretreated Boron‐Doped Diamond Electrode

An electroanalytical method for the simultaneous determination of paracetamol (PAR), caffeine (CAF), and orphenadrine (ORPH) using the square‐wave voltammetry (SWV) and a cathodically pretreated boron‐doped diamond electrode was developed. The method exhibits linear responses to PAR, CAF, and ORPH in the concentration ranges 5.4×10^?7–6.1×10^?5 M, 7.8×10^?7–3.5×10^?5 M, and 7.8×10^?7–3.5×10^?5 M, respectively, with detection limits of 2.3×10^?7 M, 9.6×10^?8 M, and 8.4×10^?8 M, respectively. The proposed method was successfully applied in the simultaneous determination of these analytes in pharmaceutical formulations.     

Silver Doped Poly(L‐valine) Modified Glassy Carbon Electrode for the Simultaneous Determination of Uric Acid,Ascorbic Acid and Dopamine

In this paper, a silver doped poly(L ‐valine) (Ag‐PLV) modified glassy carbon electrode (GCE) was fabricated through electrochemical immobilization and was used to electrochemically detect uric acid (UA), dopamine (DA) and ascorbic acid (AA) by linear sweep voltammetry. In pH 4.0 PBS, at a scan rate of 100 mV/s, the modified electrode gave three separated oxidation peaks at 591 mV, 399 mV and 161 mV for UA, DA and AA, respectively. The peak potential differences were 238 mV and 192 mV. The electrochemical behaviors of them at the modified electrode were explored in detail with cyclic voltammetry. Under the optimum conditions, the linear ranges were 3.0×10^?7 to 1.0×10^?5 M for UA, 5.0×10^?7 to 1.0×10^?5 M for DA and 1.0×10^?5 to 1.0×10^?3 M for AA, respectively. The method was successfully applied for simultaneous determination of UA, DA and AA in human urine samples.     

Sensitive Electrochemical Determination of Catechol with a Graphene Modified Carbon Ionic Liquid Electrode

In this paper a graphene (GR) modified carbon ionic liquid electrode (CILE) was fabricated and used as the voltammetric sensor for the sensitive detection of catechol. Due to the specific physicochemical characteristics of GR such as high surface area, excellent conductivity and good electrochemical properties, the modified electrode exhibits rapid response and strong catalytic activity with high stability toward the electrochemical oxidation of catechol. A pair of well‐defined redox peaks appeared with the anodic and the cathodic peak potential located at 225 mV and 133 mV (vs.SCE) in pH 6.5 phosphate buffer solution, respectively. Electrochemical behaviors of catechol on the GR modified CILE were carefully investigated and the electrochemical parameters were calculated with the results of the electrode reaction standard rate constant (k_s) as 1.24 s^?1, the charge transfer coefficient (α) as 0.4 and the electron transfer number (n) as 2. Under the selected conditions the differential pulse voltammetric peak current increased linearly with the catechol concentrations in the range from 1.0 × 10^‐7 to 7.0 × 10^?4mol L‐1 with the detection limit as 3.0 × 10^?8mol L‐1 (3σ). The proposed method was further applied to the synthetic waste water samples determination with satisfactory results     

Square Wave Voltammetry for Selective Detection of Dopamine Using Polyglycine Modified Carbon Ionic Liquid Electrode

The electrochemical polymerization of glycine on carbon ionic liquid electrode (CILE) was described. The presence of ionic liquid on the surface of CILE facilitated the electropolymerization of glycine. The polyglycine modified CILE provided a valid and simple approach to selectively detect dopamine in the presence of AA in physiological environment. The proposed sensor not only decreased the voltammetric responses of AA but also dramatically enhanced the oxidation peak current of DA compared to bare CILE. Using square wave voltammetry, the modified CILE showed good electrochemical behavior to DA, a linear range of 1.0×10^?7–3.0×10^?4 M in the presence of 1 mM ascorbic acid (AA) and a detection limit of 5.0×10^?9 M was estimated (S/N=3).     

Methylated Azopyridine as a New Electron Transfer Mediator for the Electrocatalytic Oxidation of NADH

Carbon ionic liquid electrode (CILE) has been modified with a new synthesized mediator i.e. N,N′‐dimethyl‐4,4′‐azopyridinium hexafluorophosphate (MAZPHP) via sol process and the electron transfer mediating characteristics of this mediator has been evaluated. 4,4′‐Azopyridine (AZP) did not show any electrocatalytic activity toward the selected probe, NADH, while its synthesized methylated derivative, MAZPHP, is a very efficient mediator for the electrocatalytic NADH oxidation. Cyclic voltammetry of MAZPHP/Sol/CILE exhibited a pair of reversible peaks corresponding to incorporated mediator with a formal potential of about 221 mV vs. Ag/AgCl. MAZPHP/Sol/CILE is free from fouling effects by the oxidation products of NADH which generally give hindrance to amperometric detection of NADH. Using amperometric technique, NADH can be determined in the range of 1.0×10^?5 M to 1.4×10^?3 M with a detection limit of 2.0×10^?6 M.     

Electrochemical Characterization of Epigallocatechin Gallate Using Square‐Wave Voltammetry

Electrochemical oxidation of (?)‐epigallocatechin gallate (EGCG), the main monomer flavanol found in green tea, has been investigated over a wide pH range at a glassy‐carbon electrode using square‐wave voltammetry (SWV). Square‐wave voltammograms of (?)‐epigallocatechin (EGC) and gallic acid have been studied as well. The I–E profile of EGCG, i.e. the oxidation potentials and the current responses of the first and the second peak, is pH dependent. The oxidation of EGCG is a quasireversible process over the studied pH range, which was also confirmed by the non‐linear relationship between the peak currents and squre root of frequency. The best SWV responses for EGCG were obtained at pH 2.0, frequency of 100 Hz, step of 2 mV and amplitude of 50 mV. Under these conditions, linear responses for EGCG were obtained for concentrations from 1×10^?7 M to 1×10^?6 M, and calculated LOD and LOQ for the first oxidation peak were 6.59×10^?8 M and 2.19×10^?7 M, respectively. The proposed electroanalytical procedure was applied for the determination of EGCG content in green tea. Developed SWV methodology represents a potential analytical tool in determination of catechins in tea samples.     

Detection of Uric Acid in the Presence of Dopamine and High Concentration of Ascorbic Acid Using PDDA Modified Graphite Electrode

The properties of graphite electrode (Gr) modified with poly(diallyl dimethyl ammonium chloride) (PDDA) for the detection of uric acid (UA) in the presence of dopamine (DA) and high concentration of ascorbic acid (AA) have been investigated by cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The polymer modified graphite electrode was prepared by a very simple method just by immersing the graphite electrode in PDDA solution for 20 minutes. The PDDA/Gr modified electrode displayed excellent electrocatalytic activity towards the oxidation of UA, DA and AA compared to that at the bare graphite electrode. The electrochemical oxidation signals of UA, DA and AA are well resolved into three distinct peaks with peak potential separations of 220 mV, 168 mV and 387 mV between AA‐DA, DA‐UA and AA‐UA respectively in cyclic voltammetry studies and the corresponding peak potential separations are 230 mV, 130 mV and 354 mV respectively in differential pulse voltammetry. The lowest detection limits obtained for UA, DA and AA were 1×10^?7 M, 2×10^?7 M and 800×10^?9 M respectively. The PDDA/Gr electrode efficiently eliminated the interference of DA and a high concentration of AA in the determination of UA with good selectivity, sensitivity and reproducibility. The modified electrode was also successfully applied for simultaneous determination of UA, DA and AA in their ternary mixture.     

Electrochemistry and Voltammetric Determination of Adenosine with N‐Hexylpyridinium Hexafluorophosphate Modified Electrode

An ionic liquid N‐hexylpyridinium hexafluorophosphate (HPPF₆) modified carbon paste electrode was fabricated for the sensitive voltammetric determination of adenosine in this paper. Carbon ionic liquid electrode (CILE) was prepared by mixing graphite powder and HPPF₆ together and the CILE was characterized by scanning electron microscopy (SEM) and electrochemical methods. The electrochemical behaviors of adenosine on the CILE were studied carefully. Compared with the traditional carbon paste electrode (CPE), a small negative shift of the oxidation peak potential appeared with greatly increase of the oxidation peak current, which indicated the presence of ionic liquid in the carbon paste not only as the binder but also as the modifier and promoter. Under the optimal conditions the oxidation peak current increased with the adenosine concentration in the range from 1.0×10^?6 mol/L to 1.4×10^?4 mol/L with the detection limit of 9.1×10^?7 mol/L (S/N=3) by differential pulse voltammetry. The proposed method was applied to the human urine samples detection with satisfactory results.     

Electrochemical Oxidation of Nortriptyline and Its Voltammetric Sensing at a Carbon Ionic Liquid Electrode

The electrochemical oxidation of nortriptyline at a carbon ionic liquid electrode (CILE) was investigated. Nortriptyline is electrochemically inactive on conventional electrodes but CILE exhibited excellent electrocatalytic activity toward oxidation of nortriptyline with the well-defined anodic peak at 860 mV. This characteristic was attributed to the outstanding conductivity and electrocatalytic effect of the ionic liquid, 1-octylpyridinum hexaflourophosphate, used as a binder in the construction of the electrode. The influence of experimental parameters such as pH and sweep rate was also studied. The quantitative determination of nortriptyline was performed using differential pulse voltammetry technique. Under selected conditions the anodic peak current was linear to nortriptyline concentration in the ranges of 4.8 × 10^–6 to 2.4 × 10^–5 M and 2.4 × 10^–5 to 6.4 × 10^–5 M, with correlation coefficients of 0.9992 and 09949, respectively. The detection limit was 3 × 10^–7 M.     

Voltammetric detection of guanosine and adenosine using a carbon paste electrode modified with 1-ethyl-3-methylimidazolium ethylsulfate

A novel kind of carbon paste electrode (CPE) was prepared by mixing graphite powder, liquid paraffin and the ionic liquid 1-ethyl-3-methylimidazolium ethylsulfate. The resulting electrode was used for the simultaneous determination of guanosine and adenosine by differential pulse voltammetry. Compared to a conventional CPE, the oxidation peak currents are largely increased, and the oxidation peak potentials are negatively shifted. The electrochemical responses to guanosine and adenosine were investigated. Under optimized conditions, the calibration curves are linear in the concentration range from 1.0?×?10^-6?mol?L^-1 to 1.6?×?10^-4?mol?L^-1 for guanosine, and from 1.0?×?10^-6?mol?L^-1 to 2.7?×?10^-4?mol?L^-1 for adenosine at pH 3.5. Substances potentially interfering in the biological matrix do no interfere. The method was successfully applied to detect adenosine and guanosine in human urine without sample treatments.

Electrochemical behavior and determination of L-tryptophan on carbon ionic liquid electrode

A carbon ionic liquid electrode (CILE) was fabricated by mixing N-butylpyridinium hexafluoro-phosphate (BPPF ₆ ) with graphite powder and further used for the investigation on the electrochemical behavior of L-tryptophan (Trp). The fabricated CILE showed good conductivity, inherent electrocatalytic ability and strong promotion to the electron transfer of Trp. On the CILE, an irreversible oxidation peak appeared at 0.948 V (vs. saturated calomel reference electrode). For 5.0 × 10⁻⁵ M Trp the oxidation peak current increased about 5 times and the oxidation peak potential decreased on 0.092 V compared to carbon paste electrode. The results indicated that an electrocatalytic reaction occurred on CILE. The conditions for the electrochemical detection were optimized and the electrochemical parameters of Trp on CILE were carefully investigated. Under the selected conditions, the oxidation peak current showed linear relationship with Trp concentration in the range of 8.0 × 10⁻⁶ ∼1.0 × 10⁻³ M for cyclic voltammetry and the detection limit was estimated as 4.8 × 10⁻⁶ M (3σ). The interferences of other amino acids or metal ions on the determination were tested and the proposed method was successfully applied to the synthetic sample analysis.     

Simultaneous Determination of Ascorbic Acid,Dopamine and Uric Acid at Pt Nanoparticles Decorated Multiwall Carbon Nanotubes Modified GCE

A modified electrode was fabricated by electrochemically deposition of Pt nanoparticles on the multiwall carbon nanotube covered glassy carbon electrode (Pt nanoparticles decorated MWCNT/GCE). A higher catalytic activity was obtained to electrocatalytic oxidation of ascorbic acid, dopamine, and uric acid due to the enhanced peak current and well‐defined peak separations compared with both, bare and MWCNT/GCE. The electrode surfaces were characterized by scanning electron microscopy (SEM), X‐ray diffraction (XRD) and electrochemical impedance spectroscopy (EIS). Individual and simultaneous determination of AA, DA, and UA were studied by differential pulse voltammetry. The detection limits were individually calculated for ascorbic acid, dopamine, and uric acid as being 1.9×10^?5 M, 2.78×10^?8 M, and 3.2×10^?8 M, respectively. In simultaneous determination, LODs were calculated for AA, DA, and UA, as of 2×10^?5 M, 4.83×10^?8 M, and 3.5×10^?7 M, respectively.     

Electrocatalytic Oxidation and Voltammetric Determination of Hydrazine on the Tetrabromo‐p‐Benzoquinone Modified Carbon Paste Electrode

The electrochemical properties of hydrazine studied at the surface of a carbon paste electrode spiked with p‐bromanil (tetrabromo‐p‐benzoquinone) using cyclic voltammetry (CV), double potential‐step chronoamperometry and differential pulse voltammetry (DPV) in aqueous media. The results show this quinone derivative modified carbon paste electrode, can catalyze the hydrazine oxidation in an aqueous buffered solution. It has been found that under the optimum conditions (pH 10.00), the oxidation of hydrazine at the surface of this carbon paste modified electrode occurs at a potential of about 550 mV less positive than that of a bar carbon paste electrode. The electrocatalytic oxidation peak current of hydrazine showed a linear dependent on the hydrazine concentrations and linear analytical curves were obtained in the ranges of 6.00×10^?5 M–8.00×10^?3 M and 7.00×10^?6 M–8.00×10^?4 M of hydrazine concentration with CV and differential pulse voltammetry (DPV) methods, respectively. The detection limits (3σ) were determined as 3.6×10^?5 M and 5.2×10^?6 M by CV and DPV methods. This method was also used for the determination of hydrazine in the real sample (waste water of the Mazandaran wood and paper factory) by standard addition method.     

Electrochemical Analysis of D‐Penicillamine Using a Carbon Paste Electrode Modified with Ferrocene Carboxylic Acid

The electrochemical behavior of D ‐penicillamine (D ‐PA) studied at the surface of ferrocene carboxylic acid modified carbon paste electrode (FCAMCPE) in aqueous media using cyclic voltammetry and double step potential chronoamperometry. It has been found that under optimum condition (pH 7.00), the oxidation of D ‐PA at surface of such an electrode is occurred about 420 mV less positive than that an unmodified carbon paste electrode (CPE). The catalytic oxidation peak current was linearly dependent on the D ‐PA concentration and a linear calibration curve was obtained in the ranges 7.5×10^?5 M – 1.0×10^?3 M and 6.5×10^?6 M?1.0×10^?4 M of D ‐PA with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods respectively. The detection limits (3σ) were determined as 6.04×10^?5 M and 6.15×10^?6 M. This method was also used for the determination of D ‐PA in pharmaceutical preparation (capsules) by standard addition method.     

A sensitive electrochemical sensor for detection of rutin based on a gold nanocage‐modified electrode

In this article, an electrochemical sensor based on a gold nanocage (AuNC)‐modified carbon ionic liquid electrode (CILE) was fabricated and applied to the sensitive rutin determination. The presence of AuNCs on the electrode surface greatly improved the electrochemical performance of the working electrode due to its specific microstructure and high metal conductivity. Electrochemical behavior of rutin on AuNCs/CILE was studied using cyclic voltammetry and differential pulse voltammetry with the related electrochemical parameters calculated. Under the optimal experimental conditions, the oxidation peak current of rutin and its concentration had good linear relationship in the range from 4.0 × 10^?9 to 7.0 × 10^?4 mol/L with a low detection limit of 1.33 × 10^?9 mol/L (3σ). This fabricated AuNCs/CILE was applied to direct detection of the rutin concentration in drug samples with satisfactory results, showing the real application of AuNCs in the field of chemically modified electrodes.     

Simultaneous Determination of Dopamine and Ascorbic Acid at an In‐Site Functionalized Self‐Assembled Monolayer on Gold Electrode

The in‐site functionalization of 4‐aminothiophenol (4‐ATP) self‐assembled monolayer on gold electrode at physiological pH yields a redox active monolayer of 4′‐mercapto‐N‐phenylquinone diimine (MNPD). The functionalized electrode exhibits excellent electrocatalytic responses towards dopamine (DA) and ascorbic acid (AA), reducing the overpotentials by about 0.22 V and 0.34 V, respectively, with greatly enhanced current responses. Due to its different catalytic activities toward DA and AA, the modified electrode resolves the overlapping voltammetric responses of DA and AA into two well‐defined voltammetric peaks by differential pulse voltammetry (DPV), which can be used for the simultaneous determination of these species in a mixture. The catalytic peak current obtained from DPV was linearly related to DA and AA concentration in the ranges of 5.0×10^?6?1.25×10^?4 M and 8.0×10^?6?1.3×10^?4 M with correlation coefficient of 0.999 and 0.998, respectively. The detective limits (3σ) for DA and AA were found to be 1.2×10^?6 M and 2.4×10^?6 M, respectively. The modified electrode shows good sensitivity, selectivity and stability, and has been applied to the determination of DA and AA simultaneously in samples with satisfactory results.     

Electrocatalytic Determination of Ascorbic Acid at the Surface of 2,7‐Bis(ferrocenyl ethyl)fluoren‐9‐one Modified Carbon Paste Electrode

A chemically modified carbon paste electrode with 2,7‐bis(ferrocenyl ethyl)fluoren‐9‐one (2,7‐BFEFMCPE) was employed to study the electrocatalytic oxidation of ascorbic acid in aqueous solution using cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The diffusion coefficient (D=1.89×10^?5 cm² s^?1), and the kinetic parameter such as the electron transfer coefficient, α (=0.42) of ascorbic acid oxidation at the surface of 2,7‐BFEFMCPE was determined using electrochemical approaches. It has been found that under an optimum condition (pH 7.00), the oxidation of ascorbic acid at the surface of such an electrode occurs at a potential about 300 mV less positive than that of an unmodified carbon paste electrode. The catalytic oxidation peak currents show a linear dependence on the ascorbic acid concentration and linear analytical curves were obtained in the ranges of 8.0×10^?5 M–2.0×10^?3 M and 3.1×10^?5 M–3.3×10^?3 M of ascorbic acid with correlation coefficients of 0.9980 and 0.9976 in cyclic voltammetry and differential pulse voltammetry, respectively. The detection limits (2δ) were determined to be 2.9×10^?5 M and 9.0×10^?6 M with cyclic voltammetry and differential pulse voltammetry, respectively. This method was also examined for determination of ascorbic acid in pharmaceutical preparations.     

Acetylferrocene Modified Carbon Paste Electrode; A Sensor for Electrocatalytic Determination of Hydrazine

The electrocatalytic oxidation of hydrazine at a carbon paste electrode spiked with acetylferrocene as a mediator was studied by cyclic voltammetry, differential pulse voltammetry, and chronoamperometry. In contrast to other ferrocenic compounds, acetylferrocene exhibits a chemical irreversible behavior, but it can act as an effective mediator for electrocatalytic oxidation of hydrazine, too. The heterogeneous electron transfer rate constant between acetylferrocene and the electrode substrate (carbon paste) and the diffusion coefficient of spiked acetylferrocene in silicon oil were estimated to be about 3.45×10^?4 cm s^?1 and 4.45×10^?9 cm² s^?1, respectively. It has been found that under the optimum conditions (pH 7.5) the oxidation of hydrazine occurs at a potential of about 228 mV less positive than that of an unmodified carbon paste electrode. The catalytic oxidation peak current of hydrazine was linearly dependent on its concentration and the obtained linear range was 3.09×10^?5 M–1.03×10^?3 M. The detection limit (2σ) has been determined as 2.7×10^?5 M by cyclic voltammetry. Also, the peak current was increased linearly with the concentration of hydrazine in the range of 1×10^?5 M–1×10^?3 M by differential pulse voltammetry with a detection limit of 1×10^?5 M. This catalytic oxidation of hydrazine has been applied as a selective, simple, and precise new method for the determination of hydrazine in water samples.     

Simultaneous Determination of Dopamine and Ascorbic Acid Using the Nano‐Gold Self‐Assembled Glassy Carbon Electrode

Electrochemical behavior of dopamine (DA) was investigated at the gold nanoparticles self‐assembled glassy carbon electrode (GNP/LC/GCE), which was fabricated by self‐assembling gold nanoparticles on the surface of L ‐cysteine (LC) modified glassy carbon electrode (GCE) via successive cyclic voltammetry (CV). A pair of well‐defined redox peaks of DA on the GNP/LC/GCE was obtained at E_pa=0.197 V and E_pc=0.146 V, respectively. And the peak separation between DA and AA is about 0.2 V, which is enough for simultaneous determination of DA and AA. The peak currents of DA and AA were proportional with their concentrations in the range of 6.0×10^?8–8.5×10^?5 mol L^?1 and 1.0×10^?6–2.5×10^?3 mol L^?1, with the detection limit of 2.0×10^?8 mol L^?1 and 3.0×10^?7 mol L^?1 (S/N=3), respectively. The modified electrode exhibits an excellent reproducibility, sensibility and stability for simultaneous determination of DA and AA in human serum with satisfactory result.