Foam films in the presence of functionalized gold nanoparticles

Dry aqueous foams made of anionic surfactant (SDS) and spherical gold nanoparticles are studied by small angle X-ray scattering and by optical techniques. To obtain stable foams, the surfactant concentration is well above the critical micelle concentration. The specular reflectivity signal obtained on a very thin film (thickness 20 nm) shows that functionalized nanoparticles (17 nm typical size) are trapped within the film in the form of a single monolayer. In order to isolate the film behavior, investigations are made on a single film confined in a tube. The film thinning according to the ratio of functionalized nanoparticle and SDS micelles (1:1, 1:10, 1:100) is mainly governed by the structural arrangement of SDS micelles. In thick films, nanoparticles tend to form aggregates that disappear during drainage. In particular self-organization of nanoparticles (with different surface charge) inside the film is not detected.     

Uniformly sized gold nanoparticles derived from PS-b-P2VP block copolymer templates for the controllable synthesis of Si nanowires

A monolayer of gold-containing surface micelles has been produced by spin-coating solution micelles formed by the self-assembly of the gold-modified polystyrene-b-poly(2-vinylpyridine) block copolymer in toluene. After oxygen plasma removed the block copolymer template, highly ordered and uniformly sized nanoparticles have been generated. Unlike other published methods that require reduction treatments to form gold nanoparticles in the zero-valent state, these as-synthesized nanoparticles are in form of metallic gold. These gold nanoparticles have been demonstrated to be an excellent catalyst system for growing small-diameter silicon nanowires. The uniformly sized gold nanoparticles have promoted the controllable synthesis of silicon nanowires with a narrow diameter distribution. Because of the ability to form a monolayer of surface micelles with a high degree of order, evenly distributed gold nanoparticles have been produced on a surface. As a result, uniformly distributed, high-density silicon nanowires have been generated. The process described herein is fully compatible with existing semiconductor processing techniques and can be readily integrated into device fabrication.     

Dissipative particle dynamics simulation of gold nanoparticles stabilization by PEO–PPO–PEO block copolymer micelles

Dissipative particle dynamics (DPD) was used to simulate the formation and stabilization of gold nanoparticles in poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) (PEO–PPO–PEO) block copolymer micelles. Primary gold clusters that were experimentally observed in the early stage of gold nanoparticle formation were modeled as gold bead in DPD simulation. It showed that gold beads were wrapped by the block copolymer and aggregated into spherical particles inside the micelles and forming stable Pluronic–gold colloids with two-layer structures. Increasing Pluronic concentration, molecular weight, and PPO block length led to the formation of more uniform and more stable gold nanoparticles. Density profiles of water beads suggested that the micelles, especially the hydrophobicity of the micellar cores, played an important role in stabilizing gold nanoparticles. Dynamic process indicated that the formation of gold nanoparticles was controlled by the competition between aggregation of primary gold clusters and the stabilization by micelles of block copolymers.. The DPD simulation results of gold–copolymer–water system agree well with previous experiments, while more structure information on microscopic level could be provided.     

Effect of hydrophobicity inside PEO-PPO-PEO block copolymer micelles on the stabilization of gold nanoparticles: experiments

In this paper we present the effect of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) block copolymer micelles and their hydrophobicity on the stabilization of gold nanoparticles. Gold nanoparticles were prepared by a method developed by Sakai et al. (Sakai, T.; Alexandridis, P. Langmuir 2004, 20, 8426). An absorption centered at 300-400 nm in time-dependent UV spectra provided evidence that the very first step of the synthesis was to form primary gold clusters. Then the gold clusters grew in size and were stabilized by block copolymer micelles. The stabilization capacities of the micelles were modulated by tuning the block copolymer concentration and composition and by adding salts. With good stabilization, gold particles were spherical and uniform in size with a diameter of 5-10 nm. Otherwise they were aggregates with irregular shapes such as triangular, hexagonal, and rodlike. The presence of a small amount of NaF significantly increased the stabilization capacity of the micelles and consequently modified the quality of the gold particles. Using FTIR and 1H NMR spectroscopy, micellization of the block copolymers and hydrophobicity of the micelles were proven very important for the stabilization. A higher hydrophobicity of the micelle cores was expected to favor the entrapment of primary gold clusters and the stabilization of gold nanoparticles.     

Tunable magnetic arrangement of iron oxide nanoparticles in situ synthesized on the solid substrate from diblock copolymer micelles

Hexagonal arrangement of iron oxide nanoparticles was fabricated by utilizing a single-layered film of diblock copolymer micelles. The synthesis was directly performed on the solid substrate by oxygen plasma with preserving the dimensional order of micelles so that separate procedures for synthesis and deposition of nanoparticles were not necessary. Since the oxygen plasma treatment also eliminated polymers, pure patterns of iron oxide nanoparticles were obtained. Moreover, easy control over the size of nanoparticles enabled us to selectively create a ferrimagnetic or a superparamagnetic pattern of iron oxide nanoparticles without altering the fabrication process.     

水/甲苯界面制备均匀可循环SERS基底

采用在沸水浴中还原硅酸钠的方法制备壳层约4nm的Au@SiO2核壳纳米粒子,利用水/ 甲苯两相界面诱捕出其单粒子层膜并将这层膜转移到Si片上.作为对比,采用化学方法自组装Au@SiO2膜至ITO玻璃表面. 以1,4-对苯二硫作为探针分子考察了它们的SERS活性以及可循环使用性能. 研究结果表明,Au@SiO2核壳粒子可避免待测分子与基底直接接触,NaBH4溶液可作为基底循环的洗涤剂,经化学组装的基底的可循环性能较差,每次洗涤SERS效应均有一定程度降低,而两相界面形成的单粒子致密膜的SERS效应稳定性较好,其循环性能较高,即使洗涤10次后,SERS效应仍未明显降低,此膜可作为循环使用的SERS基底.     

Surface-guided self-assembly of silver nanoparticles on edges of heterogeneous surfaces

A general method for the generation of two-dimensional (2D) ordered silver nanoparticles (av 45 nm) ring array has been demonstrated via controllable self-assembly. The selective self-assembly is conducted on the edges of a gold coated polyelectrolyte film. This film is fabricated using the monolayer polystyrene (PS) spheres (av 600 nm) on a substrate as template, followed by depositing a positively charged polyelectrolyte and gold colloids (av 17 nm) via the layer-by-layer (LbL) self-assembly technique, and finally by eliminating the PS monolayer. This gold coated polyelectrolyte film has a regular pattern of sharp edges, and those edges are composed of abundant polyelectrolyte. This heterogeneous surface is easily prepared and universal for site-selective absorption of nanoparticles (silver nanoparticles in this paper, av 45 nm). This surface-guided self-assembly is powerful for fabricating micro/nanostructures on the edges of prepatterns. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) were used to characterize the products.     

湿化学镀SPR金基底及其性能表征

建立一种由单一水相操作的表面等离子体共振法(SPR)制备金基底.即:在3-氨基丙基三甲氧基硅烷(APTMS)修饰的玻璃片上自组装一层细小的金胶纳米粒子,以此为催化模板,利用化学镀技术在纳米尺度范围内控制金膜的均匀增长,获得优异SPR信号响应所需要的金膜形貌和厚度.紫外光谱(UV-vis),透射电镜(TEM)观测表明,纳米金膜催化模板粒径约为2.5 nm.扫描电镜(SEM)观察湿化学镀SPR金基底均匀分布,粒径约为40 nm.与商品化真空镀金基底相比,湿化学镀金基底对乙醇的SPR响应强度相当,且可调控性更高.     

Macroscopic deformation of a substrate as a new method for controlling geometry and plasmon-resonant properties of highly ordered planar ensembles of metal nanoparticles

A new approach to creating highly ordered two-dimensional ensembles of nanoparticles with variable geometric parameters is proposed. It combines diblock copolymer micellar lithography and controlled deformation of a polymer substrate. The key feature of the approach is the formation of a monolayer of hexagonally packed metal precursor-containing micelles of an amphiphilic diblock copolymer on the surface of an isotropically stretched polymer plate. The average distance between micelle centers is 140 nm. Subsequent thermal treatment (or isotropic stretching) of the sample results in the shrinkage (or elongation) of the substrate, which enables one to vary the distance between micelle centers in a range of 80–200 nm while retaining hexagonal packing of the micelles in the monolayer. At the final stage, ensembles of hexagonally ordered gold nanoparticles are obtained by exposing the micellar films to air plasma. It is demonstrated that gold nanoparticles in these ensembles can be enlarged by seeded growth. The systematic study of the plasmon-resonant properties of the resulting ensembles shows that the gradual increase in the distance between 35-nm gold particles from 80 to 200 nm leads to an unexpected nonmonotonic shift of the maximum of localized surface plasmon resonance, which is, from our point of view, caused by the high degree of organization of nanoparticles on the substrate.     

基于AFM纳米氧化技术的金纳米粒子定点组装

二维纳米粒子矩阵列在纳米电子器件^[1,2]、表面增强喇曼活性基底^[3,4]、刻蚀掩模^[5]等领域具有广泛的应用前景。在这些纳米粒子阵列为内部,纳米粒子的排布是随机、无序的。这一缺点已经妨碍了纳米粒子阵列在上述领域中的进一步应用。基于此,人们开始关注纳米粒子的可控组装。传统的光刻技术^[6]、微接触印刷技术^[7]以及生物分子模板技术^[8]都被用来实现纳米粒子在固体表面上的可控组装,本实验室在纳米粒子的合成及可控组装方面也进行了研究^[7,9,11]。本文力图精确控制单个纳米粒子在基底表面上的组装位置。利用AFM纳米氧化技术。在硅表面构建了纳米级的化学图形化表面,通过不同的化学官能团,如甲基、氨基对金纳米粒子亲和性质的差异,实现了纳米粒子在固体表面的定点组装。     

Synthesis of iron oxide nanoparticles in a polyimide matrix

A monolayer of gamma-Fe(2)O(3) nanoparticles embedded in a polyimide (PI) matrix was fabricated by oxidizing an Fe metal film between two PI precursor layers. There was a critical Fe thickness ( approximately 7 nm) above which a continuous layer of gamma-Fe(2)O(3) film was formed in the PI film. Below the critical Fe thickness, the oxide film broke up into fine particles whose size was approximately 8 nm with narrow size distribution. It was further shown that these nanoparticles could have metallic cores, surrounded by an oxide layer. This method offers a unique way of covering a large surface area with fine magnetic oxide nanoparticles for potential application in high-density data-storage media.     

Effect of layer structures of gold nanoparticle films on surface enhanced Raman scattering

Using a method of collecting nanoparticles at a water/hexane interface in a close-packed monolayer film and transferring such films onto a solid substrate, three-dimensional multilayer films of nanoparticles were formed. The packed nanoparticles were gold nanospheres (NS) with a 26 nm diameter or gold nanorods (NR) with a 31 nm diameter and 74 nm length. We investigated variations in the surface enhanced Raman scattering (SERS) intensities from such nanoparticle films as the layer compositions were changed. The films stacked with NR layers generated much higher SERS intensity than those of NS layers. The SERS intensities from both kinds of films increased as the number of layers were increased. However, when the NR layer and NS layer were stacked alternately, SERS intensity varied in a zigzag fashion. It was found that the structure of top layer plays a distinguishable role in generating strong SERS enhancement while the lower layers contribute to SERS with less dependency on structures. Interlayer coupling as well as intralayer coupling was considered in order to explain the observations.     

Monolayer-protected gold nanoparticles by the self-assembly of micellar poly(ethylene oxide)-b-poly(epsilon-caprolactone) block copolymer

A study is presented of the preparation of gold nanoparticles incorporated into biodegradable micelles. Poly(ethylene oxide)-b-poly(epsilon-caprolactone) (PEO-b-PCL) copolymer was synthesized by ring-opening polymerization, and the hydroxyl end group of the PCL block was modified with thioctic acid using dicyclohexyl carbodiimide as the coupling reagent. The PEO-b-PCL-thioctate ester (TE) thus obtained was used in a later step to form monolayer protected gold nanoparticles via the thioctate spacer. Gold nanoparticles stabilized with the PEO-b-PCL block (named Au/Block (x/y), where x/y is the mole feed ratio between HAuCl4 and PEO-b-PCL-TE) were prepared and analyzed. Au/Block (1/1), Au/Block (2/1), and Au/Block (3/1) nanoparticles were found to form stable dispersions in the organic solvents commonly used to dissolve the unlabeled block copolymer. The average diameter of the nanoparticles was determined by transmission electron microscopy (TEM) and found to be 6+/-2 nm. Au/Block (4/1) nanoparticle dispersions in organic solvents, on the other hand, were not stable and produced large gold clusters (50-100 nm). Cluster formation was attributed to the low grafting density of the block copolymer, which facilitates agglomeration. For Au/Block (12/1), along the same trend, only an insoluble product was isolated. Micelles in water were prepared by the slow addition of the dilute Au/Block solution in dimethylformamide into a large excess of water with vigorous stirring. Au/Block (1/1) and Au/Block (2/1) formed nanosized structures of 5-7 nm. TEM images of stained Au/Block (1/1) micelles, made in water, clearly showed the formation of core-shell structures. Au/Block (3/1) micelles, on the other hand, were not stable and large agglomerates a few microns in size were observed. The study focuses on the synthesis, characterization, and aggregation behavior of gold-loaded PEO-b-PCL block copolymer micelles, a potential system for drug delivery in conjunction with tissue and subcellular localization studies.     

Nanoparticle‐Imprinted Polymers for Size‐Selective Recognition of Nanoparticles

Citrate‐stabilized gold nanoparticles 15 nm and 33 nm in diameter were transferred concomitantly with a monolayer of positively charged polyaniline by Langmuir–Blodgett transfer at pH 5 onto a conducting indium‐doped tin oxide (ITO) support. Films consisting of one to three layers of polyaniline with thicknesses of 1–3 nm were prepared and characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM), and X‐ray photoelectron spectroscopy. After electro‐oxidation of the Au nanoparticles in 0.1 M KCl, cavities were left behind in the film that could be analyzed by SEM. These cavities were able to recapture analyte nanoparticles from a solution of pH 10 and showed size‐exclusion properties. The amount of nanoparticles taken up by the cavities was conveniently analyzed by measuring the charge associated with the electro‐oxidation of these particles in 0.1 M KCl after the film had been rinsed with water. The size‐exclusion properties improved with the number of Langmuir–Blodgett layers transferred.     

Area-selective growth of amorphous carbon nanofibers via catalytic decomposition of polyimide thin film

A dense layer of amorphous carbon nanofibers was fabricated by pyrolyzing a thin film of polyimide using a monolayer of gold nanoparticles as a catalyst.     

Effects of the surface pressure on the formation of Langmuir-Blodgett monolayer of nanoparticles

The effects of the surface pressure on the particle arrangement of Langmuir-Blodgett (LB) monolayers of alkanethiol-capped gold nanoparticles were studied. The LB monolayers were prepared from a highly concentrated particle solution, which increases film fabrication efficiency but readily causes small particle voids in the particle array. Overcompressing the LB monolayer to a high surface pressure restructured the particles and eliminated the voids. When the gold particles capped by dodecanethiol were 8.5 nm in diameter, the particle arrangement was vastly improved and a wafer-scale LB monolayer was transferred onto a substrate at the surface pressure of 20 mN/m.     

Mineralization of gold in block copolymer micelles

Ultrasmall gold particles have been prepared inside the micelles of polystyrene-block-poly(ethylene oxide) and polystyrene-block-poly(2-vinylpyridine) in toluene. Starting point was the formation of a thermodynamically stable dispersion of HAuCl₄ or LiAuCl₄ in the inverse micelles of the block copolymer which were treated with hydrazine or pyrrole. Analysis of the effect of the reduction agent on the stability of the micelles yielded a simple model for the transformation process involving coagulation of the swelling micelles. Kinetic control of the different steps, i.e., reduction, mineralization, coagulation, film formation, allowed to prepare thin films in which highly uniform gold particles were arranged in yet unknown order. When pyrrole was employed for the reduction, the gold monocrystals got embedded in a shell of polypyrrole.     

Precisely installing gold nanoparticles at the core/shell interface of micellar assemblies of triblock copolymers

Two reduction-cleavable ABA triblock copolymers possessing two disulfide linkages, PMMA-ss-PMEO₃MA-ss-PMMA and PDEA-ss-PEO-ss-PDEA were synthesized via facile substitution reactions from homopolymer precursors, where PMMA, PMEO₃MA, PDEA, and PEO represent poly(methyl methacrylate), poly(tri(ethylene glycol) monomethyl ether methacrylate, poly(2-(diethylamino)ethyl methacrylate), and poly(ethylene oxide), respectively. Spherical micelles were obtained through supramolecular self-assembly of these two triblock copolymers in aqueous solutions. The resultant micelles with abundant disulfide bonds could serve as soft templates and precisely accommodate gold nanoparticles in the core/shell interface as a result of the formation of Au-S bonds.     

Electrochemical growth of two-dimensional gold nanostructures on a thin polypyrrole film modified ITO electrode

Two-dimensional gold nanostructures have been fabricated by electrochemical deposition of gold nanoparticles onto indium tin oxide (ITO) glass substrate modified with thin polypyrrole film. By controlling the electrodeposition conditions, gold nanoparticles with dendritic rod, sheet, flower-like (consisting of staggered nanosheets), and pinecone-like structures were generated. The flower-like gold nanoparticles showed high catalytic activity on electrochemical reduction of oxygen, and its activity was measured to be approximately 25 times that of gold pinecones and 10(4) times that of gold nanosheets in terms of gold weight. The pinecone-like nanoparticles can form a compact film with nano-/microscale binary structure like a lotus leaf surface. After modification with n-dodecanethiol, the surface showed superhydrophobic properties with a water contact angle of 153.4 degrees and a tilt angle of 4.4 degrees (5 microL droplet).     

Influence of metalation on the morphologies of poly(ethylene oxide)-block-poly(4-vinylpyridine) block copolymer micelles

Micellization of a poly(ethylene oxide)-block-poly(4-vinylpyridine) (PEO45-b-P4VP28) copolymer in water during metalation (incorporation of gold compounds and gold nanoparticle formation) with three types of gold compounds, NaAuCl4, HAuCl4, and AuCl3, was studied using dynamic light scattering (DLS) and transmission electron microscopy (TEM). The transformations of the PEO45-b-P4VP28 block copolymer micelles in water were found to depend on a number of parameters including the thermal history of the as-prepared block copolymer, the type of the metal compound, and the metal loading. For the HAuCl4-filled PE045-b-P4VP28 micelles, the subsequent reduction with hydrazine hydrate results in a significant fraction of rodlike micelles, suggesting that slow nucleation (confirmed by the formation of the large gold nanoparticles) and facilitated migration of gold ions yields the ideal conditions for sphere-to-rod micellar transition.