Static and dynamic sorption study of heavy metal ions on amino-functionalized SBA-15

Amino-functionalized SBA-15 mesoporous silica (SBA-15-NN) was synthesized using the normal grafting procedure of SBA-15 with [3-(2-Aminoethyl) aminopropyl] trimethoxysilane. Under optimal conditions, SBA-15-NN exhibited a higher adsorption capacity toward metal ions than SBA-15 in static adsorption. The results showed that the flow rate of 2?mL?min^?1 might be the optimum flow rate in dynamic adsorption, and the higher initial metal ion concentration is favorable for the adsorption of Zn(II), Co(II), and Ni(II) onto SBA-15-NN. The results indicated that SBA-15-NN could effectively remove multiple metal ions from aqueous solution as a good adsorption material.     

基于有机-无机介孔二氧化硅杂化材料对Cu^2和Co2+的选择性测定

合成了一种有机-无机介孔二氧化硅杂化材料(SBA-15-Tpy),通过透射电镜显微镜、X射线衍射、热重分析和N_2吸附-解吸曲线对其进行表征,并基于该材料建立了在水中对Cu²⁺和Co²⁺的选择性识别。研究表明,SBA-15-Tpy与Cu²⁺和Co²⁺结合后会分别在800 nm和510 nm处产生新的吸收峰,加入其它金属离子后不发生明显的吸收峰值变化。在最优条件下,检测Cu²⁺和Co²⁺的线性范围分别为2.0~200.0μmol/L和10.0~200.0μmol/L,检出限分别为0.48μmol/L和4.28μmol/L。将上述方法用于江水中Cu²⁺和Co²⁺的测定,回收率在96.0%~108.5%之间。     

Al3+离子介入提升（NH4）2SiF6对SBA-15介孔材料的水热稳定化作用

提出了一种(NH4)2SiF6处理提高SBA-15介孔材料水热稳定性的改良方法.采用SBA-15介孔材料中预引入Al3+离子,再进行1%SiO2计量的(NH4)2SiF6处理,最后用强酸洗脱预引入的Al3+.结果显示,由此处理的SBA-15材料,其水热稳定性明显优于相同条件下未预引入Al3+时(NH4)2SiF6处理的样品.两者在800°C、100%水蒸气处理12 h后,虽然均能很好保持其介观有序度、形貌及六方孔道结构,但前者的比表面积可高达271 m2/g,而后者仅为224 m2/g.表明Al3+离子介入能大幅度提升(NH4)2SiF6处理对SBA-15介孔材料的稳定化作用.这主要得益于预引入的骨架Al3+在保障(NH4)2SiF6处理修复SBA-15材料表面缺陷和进行表面疏水化、提升其水热稳定性的同时,能减缓(NH4)2SiF6释放的多余F-离子对SBA-15材料骨架的刻蚀破坏作用. Al3+离子介入的这种提升作用与其引入方式和SBA-15材料所经受的温度密切相关.     

New ZnCe catalyst encapsulated in SBA-15 in the production of 1,3-butadiene from ethanol

ZnO-CeO2/SBA-15 catalysts were prepared by two kinds of solid-state grinding method and used for the production of 1,3-butadiene(1,3-BD) from ethanol.A mixture of SBA-15(with or without organic template) and metal precursors were ground in solid-state.The obtained catalysts were characterized by TG,N2 adsorption-desorption,TEM,XRD,Py-FTIR and NH_3-TPD techniques.Superior dispersion of metal oxides and more exposed acid sites were achieved on the catalyst lOZn_1Ce_5-AS with the presence of organic template in SBA-15 during the solid-state grinding process.The catalytic performance was evaluated in a fixed-bed reactor and a 1,3-butadiene selectivity of as high as 45% is achieved.This is attributed to the coupling effect of Zn and Ce species in the mesopores of SBA-15,in which Zn promotes ethanol dehydrogenation and Ce enhances aldol-condensation,respectively.Additionally,solvent-free method inspires new catalyst synthesis strategy for the production of 1,3-butadiene from ethanol.     

La掺杂ZnO/SBA-15催化剂的制备及光催化降解孔雀石绿

采用溶胶凝胶法制备La-ZnO/SBA-15催化剂,并通过XRD、TG-DSC、XPS、TEM、SEM、N_2吸附脱附等表征分析La-ZnO/SBA-15的组成和性质,考察其对孔雀石绿溶液的催化活性。结果表明,掺杂后的SBA-15仍保持有序的二维六方结构,当n(Zn)∶n(Si)=1时,可见光照射2h,孔雀石绿降解率达99. 8%。动力学研究表明,催化剂对孔雀石绿溶液的降解符合一级反应动力学。     

Mesoporous materials incorporating a zinc(II) complex: Synthesis and direct luminescence quantum yield determination

New luminescent inorganic–organic hybrid materials incorporating the luminescent zinc(II) complex ZnL₂ (λ_em = 457 nm and Φ_em = 4.4% reference values for ZnL₂; HL = chelating ligand resulting from the reaction between salicylaldehyde and 3-aminopropyltriethoxysilane), covalently bonded to different types of mesoporous silica hosts (namely MCM-41, MCM-48 and SBA-15), were prepared via both the methods of grafting post-synthesis (GPS) and one-pot synthesis (OPS). The products obtained, which form the GPS [(GPS)(Zn/MCM-41), (GPS)(Zn/MCM-48), (GPS)(Zn/SBA-15)] and the OPS [(OPS)(Zn/MCM-41), (OPS)(Zn/MCM-48), (OPS)(Zn/SBA-15)] series, contain the ZnL₂ guest covalently bonded to the silica framework through silicon–oxygen bonds formed when the silane group is placed at the periphery of the Zn(II) coordination sphere. GPS and OPS materials were characterized by powder X-ray diffraction, N₂ adsorption/desorption, thermogravimetric analysis (TGA) and UV/vis spectroscopy. For the new mesoporous materials the emission quantum yield (EQY) was measured by means of an integrating sphere combined with a spectrofluorimeter. The ZnL₂ loading (measured by the ZnL₂/SiO₂ ratio calculated from TGA data) for MCM-41 appears to be independent of the synthesis procedure, whereas, for both MCM-48 and SBA-15, the ZnL₂/SiO₂ ratio of the materials obtained via OPS is about four times higher than products obtained from GPS. The ZnL₂ loaded GPS and OPS series show λ_em maxima at about 485 and 455 nm, respectively. Moreover, with reference to EQY (GPS)(Zn/SBA-15) and (OPS)(Zn/SBA-15), although featuring ZnL₂/SiO₂ ratios of 0.13 and 0.45, respectively, they showed similar EQY values: 2% and 5%. On the contrary, (GPS)(Zn/MCM-41) and (OPS)(Zn/MCM-41) which give similar ZnL₂/SiO₂ ratios (0.09 and 0.14) exhibit very different EQY, i.e. 2% and 22%, respectively.     

混合稀电解质条件下合成球状SBA-15粒子

在酸性合成法基础上, 不添加有机共溶剂和其它模板剂, 通过加入少量NH4F和Cu(NO3)2得到了分散的球状形貌SBA-15粒子. 对所得样品用小角X射线衍射(XRD)、N2吸脱附曲线、扫描电镜(SEM)进行表征, 讨论了不同电解质对样品形貌和孔结构的影响. 结果发现, 随着酸浓度增加, 得到了分散的规则六边形SBA-15粒子, 而加入一定量的氟化铵则得到了球形纠结状形貌的SBA-15. 实验表明, 氟离子在形成球状粒子的过程中起主要作用, 而Cu2+阻碍了球状粒子的纠结. 随着Cu2+浓度的增加, 部分硅源不能参与自组装生成SBA-15, 其原因可能是Cu2+与模板剂中亲水的聚氧乙烯形成PEO/Cu2+端基, 影响了硅源正常的缩聚.     

APTS改性SBA-15负载Ni-B非晶态合金催化加氢脱硫性能的研究

采用共价接枝法制备APTS改性介孔分子筛SBA-15,将氨基官能团接枝到SBA-15表面.并采用化学还原法制备了Ni-B/SBA-15-APTS非晶态合金催化剂,以噻吩加氢脱硫为探针反应,研究了其催化加氢脱硫性能.结果表明,240℃时,APTS改性SBA-15所负载的Ni-B催化剂噻吩转化率达到50.8%,较未改性SBA-15所负载的催化剂噻吩转化率有显著地提高.由于氨基与Ni2+的配合作用,有助于Ni在催化剂中的分散,因而更容易被还原.ICP结果表明,在相同的制备条件下,相比未改性的SBA-15,APTS改性SBA-15使其催化剂中Ni的负载量增加,并且非晶态合金组成中Ni的含量也增大,B的含量降低,有利于提高催化剂的活性.     

嫁接法制备Ni/SBA-15催化剂的催化氯苯加氢脱氯

SBA-15表面经嫁接方式引入氨基官能团,与Ni络合制备了SBA-15负载的Ni催化剂(Ni/SBA-15N)。同时,采用传统的浸渍法制备了具有相似Ni负载量的催化剂(Ni/SBA-15)。在负载量相近条件下,Ni/SBA-15N的Ni颗粒分散性均高于Ni/SBA-15。XRD和TPR结果表明,催化剂焙烧后,在氨化SBA-15表面,Ni以硅酸镍形式存在,而在SBA-15表面,Ni以NiO形式存在。Ni/SBA-15对氯苯催化加氢脱氯活性不随Ni负载量的变化而变化;而在Ni/SBA-15N中,Ni负载量增加,催化剂活性增加。     

不同助剂对CuO-ZnO/SBA-15催化CO_2加氢制甲醇性能影响的研究

以硅质骨架结构介孔分子筛SBA-15为载体,采用浸渍法合成CuO-ZnO/SBA-15(CZ/SBA-15)、CuO-ZnO-MnO_2/SBA-15(CZM/SBA-15)、CuO-ZnO-ZrO_2/SBA-15(CZZ/SBA-15)三组多孔催化剂,在固定床反应器上评价了各组催化剂催化CO_2加氢合成甲醇的性能,同时结合N_2吸附-脱附(BET)、X射线衍射(XRD)、H_2程序升温还原(H_2-TPR)、程序升温脱附(H_2-TPD、CO_2-TPD)、N_2O滴定、X射线光电子能谱(XPS)、透射电子显微镜(TEM)等表征研究了不同助剂对CO_2催化加氢制甲醇的影响。结果表明,催化剂中的金属氧化物改变了SBA-15分子筛载体的孔径大小和比表面积;催化剂CuO-ZnO-MnO_2/SBA-15、CuO-Zn O-ZrO_2/SBA-15中铜的分散度(D_(Cu))和比表面积(A_(Cu))更大,表面CuO粒径更小,更易被还原;相比Mn-O簇,Zr-O簇为增强了碱性位点,提高了甲醇选择性。此外,CuO-ZnO-ZrO_2/SBA-15具有更高的氧空位浓度,催化活性更好,其甲醇选择性为25.02%,与CuO-ZnO/SBA-15、CuO-ZnO-Mn O_2/SBA-15相比分别提高了28%和136.9%,催化效果最好。     

Sol–gel synthesis and characterization of SBA-15 in presence of metalloporphyrins: m-5,10,15,20 TPP-Ni2+, Etio-III-Ni2+ and Etio-III-VO2+

New mesoporous materials were produced incorporating, at the beginning of the SBA-15 sol–gel synthesis, three different metalloporphyrins: m-5,10,15,20-TPP-Ni²⁺, Etio-III-Ni²⁺, Etio-III-VO²⁺. These materials have the well-known hexagonal structure characteristic of SBA-15 with some differences: the presence of the porphyrins modifies the micelles generated during the sol–gel process changing the textural properties of the SBA-15-Porphyrins. Even when the hexagonal structure was preserved, the order in the crystalline structure was maintained only for short distances producing pores of different sizes and wider pore size distributions. UV–Vis results showed that the porphyrins are strongly adsorbed on SBA-15 through the interaction of their π electrons with the superficial hydroxyl groups of the support. This was confirmed by thermogravimetric results that show a high degree of incorporation of the porphyrins on the SBA-15 and a high thermal stability.     

SBA-15的孔壁碳膜修饰对钴基催化剂结构与催化性能的影响

在惰性气体中焙烧SBA-15制得孔壁被碳修饰的SBA- 15C样品,以它和SBA-15为载体,采用等量浸渍法制备了负载型Co基催化剂,并运用X射线衍射、N2物理吸附、程序升温还原、NH3吸附量热等手段对样品进行了表征.结果表明,SBA- 15C仍保持原有的六方有序的中孔结构,但其孔壁经碳修饰后发生增厚,比表面积略有下降...     

Novel inorganic-organic hybrid fluorescence chemosensor derived from SBA-15 for copper cation

A novel mesoporous SBA-15 type of hybrid material (3-trimethoxysilylpropyl)[4-(2-hydroxyphenyl)methylene] benzenesulfonamide (Schiff-SBA-15) has been obtained by co-condensation of tetraethyl orthosilicate and the organosilane, and the result of XRD confirms the order hexagonal structure of the composite. This hybrid mesoporous material is fluorescent-active, exhibiting high selectivity for sensing Cu2+ in polar solution. The remarkable fluorescence quenching in emission spectrum upon the addition of Cu2+ is attributed to the intramolecular charge transfer after the formation of a coordinate complex of a large conjugate system and Cu2+ ions.     

Mo-Ni2P/SBA-15催化剂的制备、表征及加氢脱硫催化性能

以介孔分子筛SBA-15 为载体, 通过分步浸渍硝酸镍、磷酸氢二铵、钼酸铵, 然后在H₂气流下程序升温还原(H₂-TPR), 制备了一系列不同Mo 含量的Mo-Ni₂P/SBA-15 催化剂. 采用X 射线衍射(XRD)、氮气吸脱附(BET)、透射电子显微镜(TEM)和X射线光电子能谱(XPS)对催化剂的结构进行了表征, 评价了催化剂对二苯并噻吩(DBT)的加氢脱硫(HDS)活性. 结果表明, Mo-Ni₂P/SBA-15 催化剂仍然保留有介孔结构, 催化剂的物相主要是Ni₂P. 催化剂表面的Ni 以Ni^δ+和Ni²⁺形式存在; P以P^δ-和P⁵⁺形式存在; Mo以Mo^δ+和Mo⁶⁺形式存在. Mo能促进催化性能的提高, 其中Mo含量为1% (w, 质量分数)的Mo-Ni₂P/SBA-15 催化剂具有最好的二苯并噻吩加氢脱硫催化活性, 在反应温度为380 ℃, 反应压力为3.0 MPa的条件下, 二苯并噻吩的转化率可达99.03%, 所有考察的Mo-Ni₂P/SBA-15都以直接加氢脱硫(DDS)途径为主.     

A novel method for the simple and simultaneous preconcentration of Pb2+, Cu2+ and Zn2+ ions with aid of diethylenetriamine functionalized SBA-15 nanoporous silica compound

A rapid method for the extraction and monitoring of nanogram level of Pb²⁺, Cu²⁺ and Zn²⁺ ions using uniform silanized mesopor (SBA-15) functionalized with diethylenetriamine groups and flame atomic absorption spectrometry (FAAS) is presented. The preconcentration factor of the method is 100 and detection limit of the technique is 5.5?ng?mL^?1 and 1.4?ng?mL^?1 and 0.1?ng?mL^?1 for Pb²⁺, Cu²⁺ and Zn²⁺ respectively. The time and the optimum amount of the sorbent, pH and minimum amount of acid for stripping of ions from functionalized SBA-15 were tested. The maximum capacity the functionalized SBA-15 was found to be 183.0 (±1.9) µg, 156.0 (±1.5) µg and 80.0 (±1.6) µg of Pb²⁺, Cu²⁺ and Zn²⁺/mg functionalized SBA-15, respectively.     

Fluorescence-enhanced optical sensor for detection of Al<Subscript>3+</Subscript> in water based on functionalised nanoporous silica type SBA-15

An organic–inorganic hybrid optical sensor (PQ-SBA-15) was designed and prepared through functionalisation of the SBA-15 surface with 3-piperazinepropyltriethoxysilane followed by covalently attaching 8-hydroxyquinoline. Characterisation techniques, including FT-IR, thermal gravimetric, N2 adsorption-desorption and X-ray powder diffraction analyses, showed that the organic moieties were successfully grafted onto the surface of SBA-15 without the SBA-15 structure collapsing. The evaluation of the sensing ability of PQ-SBA-15 using fluorescence spectroscopy revealed that the PQ-SBA-15 was a selective fluorescence enhancement-based optical sensor for Al³⁺ in water in the presence of a wide range of metal cations including Na⁺, Mg²⁺, K⁺, Ca²⁺, Cr³⁺, Mn²⁺, Fe³⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺, Hg²⁺ and Pb²⁺ with a limit of detection of 8.8 × 10–7 M. In addition, good linearity was observed between the fluorescence intensity and the concentration of Al³⁺.     

Dithiol-mediated incorporation of CdS nanoparticles from reverse micellar system into Zn-doped SBA-15 mesoporous silica and their photocatalytic properties

CdS nanoparticles, as prepared in reverse micellar systems, were incorporated into alkanedithiol-modified Zn-doped SBA-15 mesoporous silica (dtz.sbnd;ZnSBA-15; pore diameter, ca. 4 nm), which were themselves prepared via hydrolysis of tetraethylorthosilicate (TEOS) in the presence of Zn(NO(3))(2) and triblock copolymer, as a nonsurfactant template and pore-forming agent, followed by contact with dithiol molecules. A particle-sieving effect for the dtz.sbnd;ZnSBA-15 was observed, in that the incorporation of the nanoparticles was remarkably decreased with increasing the nanoparticle size. The resulting CdSz.sbnd;ZnSBA-15 composite was then used as photocatalysts for the generation of H(2) from 2-propanol aqueous solution. Under UV irradiation (lambda>300 nm), a high photocatalytic activity was observed for this composite material. This is effected by electron transfer from the photoexcited ZnS (dithiol-bonded Zn on SBA-15) to CdS nanoparticles. The photocatalytic activity is increased with a decrease in the number of methylene groups in the dithiol molecules, according to the rank order 1,10-decanedithiol < 1,6-hexanedithiol < 1,2-ethanedithiol.     

SBA-15介孔分子筛负载型过渡金属催化燃烧脱除乙腈废气

制备了具有规则孔道结构和较高比表面积的SBA-15介孔分子筛,采用真空旋转蒸发法将过渡金属(Cu,Co,Cr和Mn)负载到SBA-15表面,得到负载型过渡金属催化剂,并将其用于含氰废气催化燃烧的实验中,考察了其催化活性.催化剂的理化性能通过X射线衍射(XRD)、氮气吸附-脱附、透射电子显微镜(TEM)、H2-程序升温还...     

A Copper(II) Schiff base complex immobilized onto SBA-15 silica for selective oxidation of benzyl alcohol

A copper(II) Schiff base complex has been immobilized onto SBA-15 silica through a stepwise procedure and tested as an oxidation catalyst. BET surface area, total pore volume and average pore width of the SBA-15 all decrease after stepwise modification of SBA-15, while the structure of the support remains intact. The molar ratio of Cu²⁺/Schiff base is ca. 1/2 in the synthesized material. Catalytic tests showed that the supported copper complex catalyzes the oxidation of benzyl alcohol with 30 % conversion and 89 % selectivity to benzaldehyde when water is used as the solvent.     

介孔Fe/SBA-15非均相芬顿氧化水中难降解染料罗丹明B

以介孔二氧化硅SBA-15 为载体, 采用等体积浸渍法制备了Fe/SBA-15. 通过X射线衍射(XRD)、N₂吸附-脱附、扫描电镜(SEM)、透射电镜(TEM)和X射线光电子能谱(XPS)等技术对其进行了表征, 并用于对水溶液中罗丹明B (RhB)的芬顿氧化. 表征结果表明了Fe/SBA-15维持了长程有序的介孔结构, 孔径和比表面积都有所下降, 并呈现棒状体的聚集态, 平均直径为0.6 μm. Fe 以α-Fe₂O₃的形态同时存在于介孔孔道内外. 在Fe/SBA-15 和H₂O₂同时存在条件下RhB的去除是吸附和催化氧化降解的协同作用所致, 并且与Fe/SBA-15 投加量密切相关, 但与初始溶液pH 几乎无关. 当Fe/SBA-15 投加量为0.15 g·L^-1, RhB 初始浓度为10.0 mg·L^-1,H₂O₂/Fe³⁺摩尔比为2000:1,初始溶液pH为5.4和反应温度为21 ℃时, RhB去除率达到了93%. Fe/SBA-15的Langmiur 单分子层饱和吸附量为99.11 mg·g^-1. 此外, 采用H₂O₂浸泡方式对使用过的Fe/SBA-15可进行再生,连续6 次循环使用后仍可维持80%的RhB去除率, 且每次使用后Fe浸出浓度都在0.1 mg·L^-1 (或者0.6% (质量分数))以下. 基于淬灭实验、UV-Vis 光谱和气相色谱-质谱(GC-MS)联用仪分析的结果, 提出了RhB的去除机理. 非均相芬顿催化剂Fe/SBA-15可用于去除像RhB这样的生物难降解有机物.