中空介孔硅铝球形分子筛的制备及催化裂解性能

利用沸石前驱体溶液和介孔硅球(MSS)为原料,通过水热法成功制备了具有中强酸性介孔壳的中空介孔硅铝球形分子筛(HMAS)。利用透射电镜(TEM)、扫描电镜(SEM)、X射线衍射(XRD)、N2-吸脱附、27Al核磁共振(27Al NMR)及NH3程序升温脱附(NH3-TPD)对材料的结构和性能进行了表征。研究结果表明,在MSS的中空过程中伴随有物质再分配和介孔结构的逐渐演变。MSS介孔孔道中的十六烷基三甲基溴化铵(CTAB)分子,一方面保护MSS免遭强碱性沸石前驱体溶液的溶蚀,另一方面作为形成HMAS介孔壳层的模板剂。在此CTAB分子的作用下,沸石前驱体结构单元被引入到HMAS的介孔球壳上。所得材料具有介孔结构和中强酸性,在催化裂解1,3,5-三异丙苯反应中表现出优异的催化性能。     

MSU-SMFI和MCM-41的催化裂化及烷基化活性比较

以MFI沸石前驱体作为基本结构单元组装介孔硅铝分子筛MSU-S_MFI. XRD和氮气吸附数据表明MSU-SMFI具有类似MCM-41的六方排列介孔孔道结构,而且其织构参数和以传统方法合成的含铝MCM-41也大体相当.NH₃-TPD显示由沸石前驱体组装的MSU-S_MFI较硅铝比相同的含铝MCM-41介孔分子筛的固体酸量显著提高.MSU-S_MFI上的异丙苯催化裂化转化率比含铝MCM-41提高31％, 1,3,5-三异丙苯在MSU-S_MFI上也发生了更深的裂解. MSU-S_MFI上萘的叔丁基化的转化率比含铝MCM-41提高了15％.以沸石前驱体作为基本结构单元是提高介孔分子筛固体酸性的有效方法.     

微孔/介孔复合分子筛的合成及其对CO2的吸附性能

采用两步晶化法将合成的沸石前驱液(S)或沸石固体粉末(P)经不同浓度(c)的NaOH处理后, 分别以表面活性剂十六烷基三甲基溴化铵(CTAB)软模板或介孔炭(Meso-C)硬模板为导向剂, 自组装合成S-β-MCM41(c)、P-β-MCM41(c)、P-ZSM-MCM41(c)、P-ZSM-C系列微孔/介孔复合分子筛. 考察了沸石分子筛种类、碱处理液浓度以及介孔模板剂对合成复合分子筛结构与性能的影响. X射线衍射(XRD)、透射电子显微镜(TEM)和氮气吸附-脱附表征结果表明产物具有微孔/介孔多级孔结构. 该材料对CO₂的吸附能力比纯微孔或介孔材料均有明显提高, 其中P-ZSM-MCM41(2)的CO₂吸附容量最大可达1.51 mmol·g^-1, 为ZSM-5沸石吸附量的两倍多.     

表面活性剂-模板化法制备多级孔β沸石及其四氢萘加氢裂化制苯、甲苯、二甲苯的催化性能

采用表面活性剂-模板化法,分别以β-60和β-150为母体,选用十六烷基三甲基溴化铵(CTAB)作为表面活性剂,以一步和两步法制备了2种多级孔β沸石。以X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)、N₂吸附-脱附测试和NH₃程序升温脱附(NH₃-TPD)测试对多级孔β沸石的物化性质进行分析。采用等体积浸渍法负载25%的WO₃制备成加氢裂化催化剂,考察其在四氢萘加氢裂化制备苯(B)、甲苯(T)和二甲苯(X)的催化性能。结果表明：相比于母体,一步制备样品的介孔孔容提高3倍以上,两步制备样品的介孔孔容提高1倍以上。另外,以β-60为母体,一步和两步制备样品的介孔均是无序的。一步制备样品的最高BTX收率是53%,两步制备样品的最高BTX收率是51%;然而,以β-150为母体,一步制备样品的介孔是无序的,而两步制备样品的介孔是有序的。一步制备样品的最高BTX收率是46%,两步制备样品的最高BTX收率是50%。因此,多级孔β沸石制备的加氢裂化催化剂的催化性能是由介孔的含量和有序度共同决定的。     

合成和表征高温蒸汽稳定的有序介孔硅铝分子筛

用ZSM-5型沸石前驱体的稀释液和介孔MCM-4自组装合成了高温蒸汽稳定的有序介孔硅铝分子筛(MASMS-1)，并利用X-射线衍射、氮气吸脱附、场发射扫描电镜、透射电镜、傅立叶变换红外光谱和²⁷Al固体核磁等技术对其结构进行表征。在800 ℃的高温条件下，用20j%的水蒸气对MASMS-1进行4小时的水热处理，其六方有序介孔结构依然保持相当完好。MASMS-1具有良好的高温蒸汽稳定性，是由于其厚的孔壁形成沸石特征的五元环的微结构单元以及孔壁中硅羟基高度浓缩共同所致。     

NH3-SCR反应过程中NH3和NOx在Cu/SAPO-34分子筛催化剂上的吸附特性和作用

通过离子交换法制得Cu/SAPO-34菱沸石分子筛催化剂, 同时研究了NH₃和NO_x (NO和NO₂)在该催化剂上的吸附位、吸附强度、吸附量和吸附速率, 得到了不同反应气氛在Cu/SAPO-34 上的吸附性能及其在NH₃选择性催化还原(NH₃-SCR)反应中的作用. 研究采用瞬态实验、程序升温脱附(TPD)和漫反射傅里叶变换红外光谱(DRIFTS)等方法进行表征实验. 瞬态实验结果表明NH₃是吸附性气体. 程序升温脱附实验和红外漫反射实验结果表明NH₃可以吸附在布朗斯特和路易斯酸性位上形成不同的NH₃物种, 它们显示不同的SCR活性. NH₃在Cu²⁺上的吸附速率最快, 且键强最强. NO_x可以氧化并以硝酸盐/亚硝酸盐的形式吸附在Cu物种上. 最后, 本文讨论了NH₃选择性催化还原反应过程中在Cu物种上的中间物种并推测反应机理.     

介孔硅铝酸盐的合成及其在傅克反应中的催化性能

采用溶胶凝胶法合成了一系列有序性好且酸性较强的介孔硅铝酸盐材料。利用X射线粉末衍射(XRD)、透射电镜(TEM)、²⁷Al核磁共振(²⁷Al NMR)、氨气程序升温脱附(HN₃-TPD)及吡啶吸附红外光谱(Py-FT-IR)对制备的介孔硅铝酸盐材料的结构和性能进行表征,并考察了材料在苯甲醚和苯甲醇的傅克烷基化反应中的催化活性。实验结果表明：合成过程中,表面活性剂的用量、硅铝物质的量的比会影响材料结构的有序性,醋酸用量对材料结构有序性影响很小;进一步研究结果表明,n_Si / n_Al比会影响材料的酸催化活性,当n_Si / n_Al=10时材料的酸催化活性最高。氨气程序升温脱附和吡啶吸附红外光谱表明n_Si / n_Al=10的材料含有最多的B酸酸量。     

晶种导向干凝胶法制备成型ZSM-5分子筛

在干凝胶法制备ZSM-5 分子筛的体系中添加晶种导向剂, 控制分子筛的生长, 制备了纳米沸石组装的无粘结剂成型多级孔ZSM-5 分子筛, 一步完成纳米分子筛的制备及组装成型, 即克服了传统纳米粒子难以过滤分离的问题, 同时组装所形成的多级孔有助于改善分子在催化剂内的扩散, 从而提高催化反应效率. 以硅胶、薄水铝石为原料, 四丙基氢氧化铵(TPAOH)和ZSM-5 晶种导向胶作为粘结剂, 通过混捏、挤条得到直径2 mm的条状前驱物, 随后通过干凝胶转换法制备成型分子筛. 所用晶种导向剂组成为0.35TPAOH:1SiO₂:20H₂O:4C₂H₅OH. 通过X射线衍射(XRD), 热重(TG)分析和傅里叶变换红外(FTIR)光谱等方法对分子筛晶化过程进行了表征, 结果表明晶种导向剂加入量对分子筛生长速度及多级孔结构均有影响. 当所加晶种导向剂中TPAOH与SiO₂的摩尔比为0.025时, 经过3 h晶化, 分子筛相对结晶度达到100%. 扫描电镜(SEM)结果表明, 合成的分子筛尺寸约为200 nm, 组装形成的多级孔分子筛的介孔体积为0.28 cm³·g^-1. 通过NH₃ 程序升温脱附(NH₃-TPD)考察了所得成型分子筛的酸性, 发现该分子筛酸性与市售的粉末H-ZSM-5分子筛类似.     

单分散SnO2中空微纳米球的制备和性质

模板法是制备无机中空微纳米球的重要方法之一. 本文以苯乙烯为单体, 通过乳液聚合得到粒径约为620 nm的单分散聚苯乙烯(PS)微球. 以磺化后的聚苯乙烯(PSS)微球为模板, 利用阴阳离子静电吸附作用, 将PSS与前驱体SnSO₄中的Sn²⁺结合. 通过Sn²⁺在乙醇-水介质中的水解作用得到核-壳复合结构, 再经高温煅烧, 得到SnO₂中空微纳米球. 实验对前驱体的浓度、表面活性剂的用量、反应时间及模板选择等方面做了研究,通过扫描电镜(SEM)、X 射线衍射(XRD)、红外(IR) 光谱、热重分析(TGA)、H₂ 程序升温还原(H₂-TPR)、Brunauer-Emmett-Teller (BET)比表面积等技术深入探究SnO₂中空微纳米球的结构, 并对比中空SnO₂与实心粒子的氧化还原特性. BET和H₂-TPR显示将SnO₂制备成微纳米空心球后其比表面积增大, 表面氧空位明显增多, 氧化活性明显提高. 从IR 及XRD推断核-壳结构形成机理, 进而优化出简单合理的实验方案, 获得表面光滑、结构致密, 包覆厚度可控的SnO₂中空微纳米球.     

MnOx/Al-SBA-15的结构性质及低温NH3选择性催化还原NOx

采用后合成法制备MnO_x/Al-SBA-15催化剂, 考察了催化剂的低温NH₃选择性催化还原(SCR)NO_x的性能. 利用傅里叶透射红外变换(FTIR)光谱、N₂吸附-脱附、X射线衍射(XRD)、扫描电镜(SEM)、拉曼光谱(Raman)、X射线光电子能谱(XPS)及NH₃程序升温脱附(NH₃-TPD)的表征手段, 对催化剂的结构性质和SCR性能进行了系统分析. 结果表明, 适量Al的掺杂能提高MnO_x/SBA-15催化剂的SCR活性, 当硅铝摩尔比为50时, 催化剂活性最佳. 表征结果显示, Al掺杂后, 催化剂仍保持良好的骨架结构, 较大比表面、孔容和孔径, 并且Mn在催化剂表面富集, 由低价态转化为高价态, MnO₂为催化剂的主要活性相. 此外, Al的掺杂使MnO_x在催化剂表面高度分散, 表面酸性增强, 从而提高了催化剂的SCR活性.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.