Heat shrinkability of electron-beam-modified thermoplastic elastomeric films from blends of ethylene-vinylacetate copolymer and polyethylene

The heat shrinkability of electron-beam-irradiated thermoplastic elastomeric films from blends of ethylene–vinylacetate copolymer (EVA) and low-density polyethylene (LDPE) has been investigated in this paper. The effects of temperature, time and extent of stretching and shrinkage temperature and time have been reported. Based on the above data, the optimized conditions in terms of high heat shrinkage and low amnesia rating have been evaluated. Influence of radiation doses (0–500 kGy), multifunctional sensitizer levels (ditrimethylol propane tetraacrylate, DTMPTA), and blend proportions on heat shrinkability has been explained with the help of gel fraction and X-ray data. With the increase in radiation dose, gel fraction increases, which in turn gives rise to low values of heat shrinkage and amnesia rating. At a constant radiation dose and blend ratio, percent heat shrinkage is found to decrease with increase in DTMPTA level. Gel content increases with the increase in EVA content of the blend at a constant radiation dose and monomer level, giving rise to decrease in heat shrinkability. Heat shrinkage increases with the increase in percent crystallinity, although the amnesia rating follows the reverse trend.     

Photo-luminescence of Risø B3 and PVB films for application in radiation dosimetry

Risø B3 film dosimeters (23 μm) prepared from poly(vinyl butyral) (PVB) incorporating pararosaniline cyanide, as the radiation-sensitive element and PVB films (25 μm) prepared from PVB without any additives are investigated for γ-radiation measurement using spectrofluorimetry based on their emission properties. The unirradiated Risø B3 film when excited at 554 nm shows an emission band at 602 nm while PVB film shows an emission band at 305 nm when excited at 235 nm wavelength. The fluorescence intensity of both emission bands decreases with the increase of absorbed dose due to the damage caused by ionizing radiation. The useful dose range of Risø B3 film extends up to 120 kGy while that of PVB film extends up to 60 kGy. The response of Risø B3 film increases with the increase of relative humidity during irradiation while that of PVB has less effect in the humidity range of 20–70%. The percent uncertainty associated with the measurement of the dose response was found to be ±3% (1σ) for both films. Risø B3 and PVB films show good post-irradiation stability in dark and indirect daylight where the deviation in the response overall a 2-month storage period was found to be ±5% for Risø B3 and ±2% for PVB.     

Characterization of structural changes of poly(vinyl methyl ether) gamma-irradiated in diluted aqueous solutions

An aqueous deoxygenated dilute PVME solution (cP = 0.5 mass %) was irradiated with gamma-rays at different radiation doses (D = 0.2-10 kGy). At these concentrations and doses contracted molecules are formed but no macroscopic networks. For the analysis of the structural changes, the irradiated samples were analyzed by size exclusion chromatography (SEC) with a triple detector system, static light scattering, and viscometry. SEC measurements necessitate for the application of the universal calibration principle the knowledge of the Kuhn-Mark-Houwink (KMH) parameters. To obtain these parameters commercially available poly(vinyl methyl ether) was fractionated and analyzed by the same means. We found at 30 degrees C a KMH relationship to [eta] = 0.0226 (mL/g) x Mw(0.67) in THF. We observed an increase in molar masses without any significant structural changing for D < 0.5 kGy. With increasing radiation dose, the intramolecular cross-linking reaction becomes more and more important. The results of viscosity measurements show a slight increase in contraction for 1.0 kGy. For irradiation dose higher than D > 1.5 kGy, a strong contraction occurs. For D > 5.0 kGy, the favored intramolecular reactions lead to the formation of microgels.     

Electron beam irradiated polyamide-6,6 films—II: mechanical and dynamic mechanical properties and water absorption behavior

Electron beam irradiation of poly(iminohexamethylene-iminoadipoyl) (Polyamide-6,6) films was carried out over a range of irradiation doses (20–500 kGy) in air. The mechanical properties were studied and the optimum radiation dose was 200 kGy, where the ultimate tensile stress (UTS), 10% modulus, elongation at break (EB) and toughness showed significant improvement over the unirradiated film. At a dose of 200 kGy, the UTS was improved by 19%, the 10% modulus by 9% and the EB by 200% over the control. The dynamic mechanical properties of the films were studied in the temperature region 303–473 K to observe the changes in the glass transition temperature (T_g) and loss tangent (tan δ) with radiation dose. The storage modulus of the film receiving a radiation dose of 200 kGy was higher than the unirradiated film. The water uptake characteristics of the Polyamide-6,6 films were investigated. The water uptake was less for the films that received a radiation dose of 200 and 500 kGy than the unirradiated film. The role of crystallinity, crosslinking and chain scission in affecting the tensile, dynamic mechanical and water absorption properties was discussed.     

Effect of γ-radiation on ointment cold cream

In this paper, Co-60γ ray was used to irradiate the ointment cold cream at room temperature (25°C). We also used FTIR, GC and thin film chromatogram to analyse various irradiated samples. It was found that the ointment cold cream can be irradiated at dose of 5–35 kGy and at dose rate from 0.2 to 0.6 kGy/h at room temperature (25°C) without evident decomposition. At dose of 5–15 kGy, the number of bacteria can be reduced to hygienic standard value. The radiation sterilization is a safe method for killing the bacteria in the ointment cold cream.     

Grafting onto poly(vinyl alcohol). II. Graft copolymerization of methyl acrylate and vinyl acetate and their binary mixture using γ-rays as initiator

Methyl acrylate (MA), vinyl acetate (VAc) and their binary mixture (MA + VAc) have been graft copolymerized onto poly(vinyl alcohol) using γ-rays as initiator by mutual radiation method in aqueous medium. The optimum conditions for affording maximum grafting have been evaluated. The percentage of grafting has been determined as a function of total dose, concentrations of poly(vinyl alcohol), MA, VAc, and their binary mixture. Rate of grafting (R_p) and induction period (I_p) have been determined as a function of total initial mixed monomer concentration and concentration of poly(vinyl alcohol). The graft copolymer has been characterized by thermogravimetric method. The effect of donor monomer (vinyl acetate) on percent grafting of acceptor monomer (methyl acrylate) has been explained.     

Radiation-induced grafting of perfluorinated vinyl ether into fluorinated polymer films

We report herein the first successful grafting of perfluorinated vinyl ether monomer into base polymer films by simultaneous radiation method. 2-Bromotetrafluoroethyl trifluorovinyl ether (BrTFF) could be grafted into poly(ethylene-co-tetrafluoroethylene) (ETFE) films by γ-rays irradiation at room temperature. The grafting yield increased linearly with an increase in the dose up to 1400 kGy. The required dose for a satisfactory grafting yield, such as 20%, was as high as ca. 400 kGy probably due to low polymerization reactivity of fluorinated monomers. However, the solvent and catalyst had no positive influence for improving the grafting yield. FTIR spectra and SEM-EDS testified that BrTFF was successfully grafted into ETFE films homogeneously in the perpendicular direction. The thermal analysis of the grafted films further indicated no phase separation between poly(BrTFF) grafts and ETFE films, probably owing to high compatibility of the fluorinated grafts and base polymers.     

The effect of high-energy electron beam irradiation and content of ATH upon mechanical and thermal properties of EVA copolymer

Mechanical and thermal properties of ethylene vinyl acetate (EVA) mixed with various amounts of alumina trihydrate (ATH), irradiated with 5 MeV electron beam at dose range varied from 38 to 190 kGy, have been studied. A small amount (1%) of triallyl cyanurate has been used as a radiation sensitizer. It has been found that (i) EVA samples with various contents of ATH are crosslinked, (ii) crosslinking increases with irradiation dose, (iii) the mechanical properties of samples improve by irradiation and (iv) decomposition of samples takes place at two stages and due to irradiation, decomposition temperatures shift to higher values. These studies were carried out in order to obtain a suitable compound for wire and cable insulation.     

Effect of dose rate on inactivation of microorganisms in spices by electron-beams and gamma-rays irradiation

Total aerobic bacteria in spices used in this study were determined to be 1 × 10⁶ to 6 × 10⁷ per gram. A study on the inactivation of microorganisms in spices showed that doses of 6–9kGy of EB (electron-beams) or γ-irradiation were required to reduce the total aerobic bacteria in many However, a little increase of resistance was observed on the inactivation of total aerobic bacteria in many spices in case of EB irradiation. These difference of radiation sensitivities between EB and γ-rays was explained by dose rate effect on oxidation damage to microorganisms from the results of radiation sensitivities of Bacillus pumilus and B. megaterium spores at dry conditions. On the other hand, these high dose rate of EB irradiation suppressed the increase of peroxide values in spices at high dose irradiation up to 80 kGy. However, components of essential oils in spices were not changed even irradiated up to 50 kGy with EB and γ-rays.     

Effect of gamma radiation on growth and survival of common seed-borne fungi in India

The present work describes radiation-induced effects of major seeds like Oryza sativa Cv-2233, Oryza sativa Cv-Shankar, Cicer arietinum Cv-local and seed-borne fungi like Alternaria sp., Aspergillus sp., Trichoderma sp. and Curvularia sp. ⁶⁰Co gamma source at 25 °C emitting gamma ray at 1173 and 1332 keV energy was used for irradiation. Dose of gamma irradiation up to 3 kGy (0.12 kGy/h) was applied for exposing the seed and fungal spores. Significant depletion of the fungal population was noted with irradiation at 1–2 kGy, whereas germinating potential of the treated grain did not alter significantly. However, significant differential radiation response in delayed seed germination, colony formation of the fungal spores and their depletion of growth were noticed in a dose-dependent manner. The depletion of the fungal viability (germination) was noted within the irradiation dose range of 1–2 kGy for Alternaria sp. and Aspergillus sp., while 0.5–1 kGy for Trichoderma sp. and Curvularia sp. However, complete inhibition of all the selected fungi was observed above 2.5 kGy.     

Radiation preparation of PVA-g-NIPAAm in a homogeneous system and its application in controlled release

Thermosensitive PVA-g-NIPAAm copolymers were prepared by graft copolymerization of N-isopropylacrylamide (NIPAAm) onto poly (vinyl alcohol) (PVA) in homogeneous system of dimethyl sulfoxide (DMSO) by ⁶⁰Co-γ irradiation at room temperature. The factors of affecting the grafting yield, such as radiation dose, dose rate, acid concentration, were investigated. It was found that the grafting yield was increased with dose up to 30 kGy, but decreased slightly with dose rate from 61.2 to 50.1 Gy/min. The acid concentration also had influence on the grafting yield. Then the hydrogel of PVA-g-NIPAAm copolymer was made through a freezing–thawing process. The PVA-g-NIPAAm hydrogel exhibited obvious thermal sensitivity, which was observed from the differences of swelling behavior in water at different temperatures (below or above LCST). In addition, the release of Methylene Blue (MB) from this kind of hydrogel was studied. The release rate of MB from PVA-g-NIPAAm copolymer hydrogel at 48°C was faster than that at 15°C due to the shrinkage of the hydrogel at 48°C.     

Sterilization of health care products by 5 MeV bremsstrahlung (X ray)

Radiation sensitivities of . pumilus and spores were examined to bremsstrahlung of 5 MeV EB and Cobalt -60 γ rays in order to confirm the effects of radiation and dose rate. Biological indicators (SPORTROL, NAmSA, USA) were irradiated with the X ray in the dose rate range of 4.7–47kGy/h. D-value of spores was 1.4–1.5 kGy, and that of was 1.1–1.3 kGy. The D-values of and have very small dose rate dependences to X ray, and the D-values are similar to those of γ ray. Dose distribution by X-ray and γ irradiation was measured for cartons containing 32 unit dialyzers. The D_max./D_min. of the X-ray irradiation (1.2) was smaller than that of γ ray (1.3).     

Dose response and post-irradiation characteristics of the Sunna 535-nm photo-fluorescent film dosimeter

Results of characterization studies on one of the first versions of the Sunna photo-fluorescent dosimeter™ have previously been reported, and the performance of the red fluorescence component described. This present paper describes dose response and post-irradiation characteristics of the green fluorescence component from the same dosimeter film (Sunna Model γ), which is manufactured using the injection molding technique. This production method may supply batch sizes on the order of 1 million dosimeter film elements while maintaining a signal precision (1σ) on the order of ±1% without the need to correct for variability of film thickness. The dosimeter is a 1 cm×3 cm polymeric film of 0.5-mm thickness that emits green fluorescence at intensities increasing almost linearly with dose. The data presented include dose response, post-irradiation growth, heat treatment, dosimeter aging, dose rate dependence, energy dependence, dose fractionation, variation of response within a batch, and the stability of the fluorimeter response. The results indicate that, as a routine dosimeter, the green signal provides a broad range of response at food irradiation (0.3–5 kGy), medical sterilization (5–40 kGy), and polymer cross-linking (40–250 kGy) dose levels.     

Sunna dosimeter: an integrating photoluminescent film and reader system; work in progress

A new radiation dosimeter, consisting of an optically-stimulated polymer film containing a photofluorescent sensor, can serve as a routine dosimeter and radiographic imaging medium for high-dose applications in the absorbed dose range 0.1–100 kGy. The flexible, colorless, opalescent film having a uniform thickness of 0.240 (±0.005) mm or certain other films in the thickness range 0.08–0.60 mm, are available in large batches. They can be read rapidly with a simple table-top spectrofluorimeter, excitation wavelength (λ=450 nm) and emission wavelength (λ=670 nm), giving a type A uncertainty of dose evaluation of <±5% at 95% confidence level. It supplies either single integrated dose readings or two-dimensional radiographic images with relatively high spatial resolution. The present work focuses on the following gamma-ray response characteristics of the system: inter- and intra-batch reproducibility, pre- and post-irradiation stability, and dependence of dose interpretations on absorbed dose rate and irradiation temperature.     

The effect of gamma irradiation on mechanical, and thermal properties of recycling polyethylene terephthalate and low density polyethylene (R-PET/LDPE) blend compatibilized by ethylene vinyl acetate (EVA)

A study has been made on the compatibility of recycled polyethylene terephthalate (R-PET) and low density polyethylene (LDPE) blend in the presence of ethylene vinyl acetate (EVA) as a compatibilizing agent prepared by extrusion hot stretching process. EVA content in the blend as a compatibilizing agent was an enhancement effect on radiation crosslinking of R-PET/EVA/LDPE blends and the highest radiation crosslinking was obtained when the EVA content was reached at 10 % EVA when irradiated by gamma irradiation. Blends containing different (EVA) ratios were irradiated to different doses of gamma irradiation 25, 50 and 100 kGy. The effect of the compatibilizer and radiation on mechanical, thermal properties of R-PET together with LDPE and morphology has been investigated. It was found that gamma irradiation together with the presence of compatibilizing agent (EVA) has positive effect on the mechanical and thermal properties of R-PET/LDPE blend. The structural properties of R-PET/LDPE modified by gamma irradiation and EVA as compatibilizing agent was examined by SEM. Also, it was found that the optimum concentration of EVA and gamma irradiation dose was found to be 10 % EVA and 100 kGy, respectively.     

Physical properties of gamma irradiated poly(vinyl alcohol) hydrogel preparations

Poly(vinyl alcohol) films from 15% w/w aqueous solutions and a thickness of 0.2 mm were selected for this study. The films were first humidified and then acetalized and/or gamma irradiated. Then, their physical properties were tested. Tensile strength of the hydrogel films reached its maximum value in samples irradiated with a 80 kGy dose, in the case of acetalized films the dose necessary for maximum tensile strength was only 40 kGy. The combination of acetalization with formaldehyde and gamma radiation produced an elastic hydrogel with good tackiness and excellent mechanical and thermal strength.     

Effects of irradiation in combination with waxing on the essential oils in orange peel

The study evaluated the effects of waxing and irradiation dose on the essential oils in orange peel. Mature oranges (Maroc late) waxed or unwaxed were treated with 0–2 kGy radiation. Volatiles in the peel were extracted and analyzed by G.C. D-limonene was significantly lower (P0.05) in waxed oranges; levels in samples treated with 2 kGy were higher than those treated with 0 or 1 kGy. Linalool, methyl anthranilate and 3.7-dimethyl-2.6-octadienal decreased as the dose increased. The analysis of variance indicates that only linalool was influenced by post-irradiation storage time. The level of this compound increased with storage time.     

Thermoluminescence of contaminating minerals for the detection of radiation treatment of dried fruits

Several types of dry fruits (pistachio nut, dried apricot, almond and raisins) have been investigated for detection of their radiation treatment by gamma rays or electron beam using thermoluminescence (TL) measurements. These samples were irradiated to 1.0–3.0 kGy (gamma rays) or 0.75–3.9 kGy (10 MeV electron beam). Thermoluminescence glow curves for the contaminating minerals separated from the dry fruits were recorded between the temperature range of 50°C and 500°C. In all the cases, the intensity of TL signal for the irradiated dry fruits was 1–3 orders of magnitudes higher than the TL intensity of the corresponding unirradiated control samples allowing clear distinction between the irradiated and unirradiated samples. These results were normalized by re-irradiating the mineral grains with a gamma-ray dose of 1.0 kGy, and a second glow curve was recorded. The ratio of intensity of the first glow curve (TL₁) to that after the normalization dose (TL₂), i.e. (TL₁/TL₂) was determined and compared with the recommended threshold values. These parameters, together with comparison of the shape of the first glow curve, gave unequivocal results about the radiation treatment of the dry fruit samples.     

Improvement of the ESR detection of irradiated food containing cellulose employing a simple extraction method

Fruit may be irradiated at rather low doses, below 1 kGy in combination treatments or for quarantine purposes. To improve the ESR detection sensitivity of irradiated fruit de Jesus et al. (Int. J. Food Sci. Technol. 34 (1999) 173.) proposed extracting the fruit pulp with 80% ethanol and measuring the residue with ESR using low power (0.25 mW) for detection of ‘cellulosic’ radicals. An improvement in ESR sensitivity using the extraction procedure could be confirmed in this paper for strawberries and papayas. In most cases, a radiation dose of 0.5 kGy could be detected in both fruits even after 2–3 weeks storage. In addition, some herbs and spices were also tested, but only for a few of them the ESR detection of the ‘cellulosic’ signal was improved by previous alcoholic extraction.

As an alternative to ESR measurements, other detection methods like DNA Comet Assay and thermoluminescence were also tested.     

Dosimetric properties of commercial grade plexiglas as a possible routine dosimeter for radiation processing

Dyed and undyed polymethylmethacrylate (PMMA) are commercially available for high dose dosimetry in radiation processing applications. In order to investigate the properties of the locally available clear perspex as a subsitute routine dosimeter, we have looked into the optical and dosimetric properties of clear perspex sheets with a thickness of 2 mm.

The selected wavelength used for read out was 314 nm. Absorption spectra obtained showed a sharp cutoff at 260 nm wavelength. Post-irradiation studies at different doses indicate that the optical density decrease with storage time. No significant dose rate dependence in the range of 1.1 to 11 kGy/hr has been observed. The temperature response of the said clear perspex in the range of 0–30°C during irradiation has also been determined.

Comparison of the optical density versus dose for the local clear perspex against that of red perspex from Harwell, at an absorbed dose of 25 kGy, as obtained in our gamma irradiator, IR-136, showed a difference of 3%. The reproducibility of the local clear PMMA has been observed to be also less than 3% in an absorbed dose range of 5 to 50 kGy.