高效液相色谱–原子荧光光谱法测定水产品中4种砷形态

建立高效液相色谱–原子荧光光谱法对水产品中4种砷形态[亚砷酸盐As(Ⅲ)、砷酸盐As(Ⅴ)、一甲基砷酸、二甲基砷酸]进行测定。优化后的实验条件:负高压为270 V,灯电流为80 m A,原子化高度为10 mm,硼氢化钾浓度为20 g/L(含5 g/L KOH),载流为体积分数5%的盐酸。方法的线性范围为0~100μg/L,线性相关系数大于0.999。各种砷形态的检出限为0.20~0.45μg/L;测量结果的相对标准偏差为1.98%~4.81%(n=6);加标回收率为88.4%~101.7%。该方法灵敏度高,快速、准确,检测成本低,可用于水产品中砷形态的检测。     

虾粉中总砷测定方法的探讨

用氢化物原子荧光光度法测定虾粉中总砷含量时,对干法灰化、湿法消解、微波消解3种样品处理方法对虾粉中砷元素测定结果的影响进行了比较。通过试验确定了最佳消解条件。砷元素浓度在0~10μg/L的范围内与荧光强度呈线性关系,线性相关系数r=0.999 6,检出限为0.2μg/L。比对结果表明,干法灰化适合于测定虾粉中总砷的含量,湿法消解测定总砷的含量偏低,微波消解不适合测定虾粉中总砷的含量。采用干法灰化-氢化物原子荧光光度法测定虾粉中总砷含量,加标回收率为76.2%~106.0%。     

氢化物发生-原子荧光光谱法同时测定高纯铟中As、Sb

研究了氢化物发生-原子荧光光谱法测定高纯铟中微量As、Sb元素的条件,选择了适宜的反应条件以及仪器的最佳工作条件,考察了铟基体对被测元素的干扰,采用基体匹配的方法消除干扰,建立了氢化物发生-原子荧光光谱法测定高纯铟中微量的As、Sb的分析方法。As、Sb的检出限分别为0.18和0.28 ng/mL,测定下限为1.2×10-5和1.9×10-5,相对标准偏差分别为1.9%和1.7%,回收率为97.4%和103%,适用于5～6 N高纯铟中微量As、Sb的测定。     

Speciation of arsenic in a contaminated soil by solvent extraction

Soil collected from a disused cattle dip in northern New South Wales was studied with the aim of developing an inexpensive, yet effective method for quantitative determination of arsenic(III), arsenic(V) and total organic arsenic in a contaminated soil. Hydrochloric acid extractions were used as a method for removal of the arsenic from the soil in a form suitable for speciation. It was found that the extraction efficiency varied with the ratio of soil to acid, and the concentration of the acid. Arsenic(III), as arsenic trichloride, was selectively extracted into chloroform from a solution highly concentrated in hydrochloric acid. This was followed by back-extraction of the arsenic into water. Total inorganic arsenic was determined in a similar manner after the reduction of arsenic(V) to the trivalent state with potassium iodide. Arsenic(V) was determined by the difference between the results for arsenic(III) and total inorganic arsenic. All analyses for the various arsenic species were performed by hydride generation-atomic absorption spectroscopy; concentrations of total arsenic in the soil were confirmed using X-ray fluorescence spectrometry. It was found that all the arsenic in the soil was present as inorganic arsenic in the pentavalent state. This reflects the ability of arsenic to interchange between species, since the original species in cattle dipping solution is arsenic(III).     

Determination of arsenic species in oyster tissue by microwave‐assisted extraction and liquid chromatography–atomic fluorescence detection

A method for the determination of arsenic species in oyster tissue is established. The extraction of arsenic species is carried out by using low‐power microwaves. Quantitative extraction is obtained at a power of 40 W, and in 5 min, using the extracting agent methanol/water (1 + 1). The measurements are carried out using liquid chromatography–UV irradiation–hydride generation–atomic fluorescence detection (LC–UV–HG–AFS). Three arsenic species were detected in oyster tissue: arsenobetaine (AsBet) (87%), a probable arsenosugar (AsS) (4.9%), and dimethylarsinate (DMA) (4.7%). No influence of the clean‐up, the microwave field or the IR drying system on the stability of the arsenic compounds was observed. The extracts can be kept stable up to 3 days at 4 °C. The performance of the method is proved on fresh samples, as they are usually analysed in routine laboratories. Copyright © 2001 John Wiley & Sons, Ltd.     

液相色谱-电感耦合等离子体质谱法测定稻米中的5种砷形态

建立了稻米中砷酸根[As（Ⅴ）]、亚砷酸根[As（Ⅲ）]、砷甜菜碱（AsB）、一甲基砷（MMA）和二甲基砷（DMA）的液相色谱-电感耦合等离子体质谱（LC-ICP-MS）检测方法。以0.3 mol/L硝酸水溶液为提取试剂,样品在石墨消解仪中于95 ℃消解1.5 h,上清液供LC-ICP-MS分析。5种砷形态采用Dionex IonPac AS19阴离子交换柱（250 mm×4 mm）分离,经ICP-MS检测。比较了4种提取液对稻米中5种砷形态的提取效率,并对提取溶剂的浓度、提取温度和提取时间等条件进行了优化。通过加标回收试验结合测定标准物质考察了方法准确度及精密度,在2个加标水平上各形态的回收率为89.6%~99.5%,RSD（n=5）不大于3.6%,大米标准物质中各形态之和的测定结果与其标准值吻合,5种砷形态的线性范围AsB和DMA为0.05~200 μg/L,As（Ⅲ）和MMA为0.10~400 μg/L,As（V）为0.15~600 μg/L,方法检出限为0.15~0.45 μg/kg。结果表明,本方法简单、灵敏、耐用,可用于稻米中5种砷形态的准确定量和风险评估。     

Optimization of the extraction for the determination of arsenic species in plant materials by high-performance liquid chromatography coupled with hydride generation atomic fluorescence spectrometry

A study has been conducted for the separation and the determination of arsenic species in plants using high-performance liquid chromatography–hydride generation atomic fluorescence spectrometry with emphasis on sample extraction procedures. Various extraction solvents have been applied to extract arsenic species from plants in order to investigate the uptake, transfer and accumulation processes of arsenic. The method was optimized with respect to the selection of extraction solvent, extraction time and the number of extraction steps. The analytical procedure has been validated by analyzing standard reference material GBW 82301 (peach leaves) and successfully used for the arsenic speciation in plants grown on contaminated soil near an arsenic mine. Inorganic arsenic, especially arsenate (As(V)) appears to be the major component in plants and organic arsenic species of monomethylarsenic acid and dimethylarsenic acid were detected at low concentrations.     

Speciation analysis of arsenic in groundwater from Inner Mongolia with an emphasis on acid-leachable particulate arsenic

Arsenic in drinking water affects millions of people around the world. While soluble arsenic is commonly measured, the amount of particulate arsenic in drinking water has often been overlooked. We report here determination of the acid-leachable particulate arsenic and soluble arsenicals in well water from an arsenic-poisoning endemic area in Inner Mongolia, China. Water samples (583) were collected from 120 wells in Ba Men, Inner Mongolia, where well water was the primary drinking water source. Two methods were demonstrated for the determination of soluble arsenic species (primarily inorganic arsenate and arsenite) and total particulate arsenic. The first method used solid phase extraction cartridges and membrane filters to separate arsenic species on-site, followed by analysis of the individual arsenic species eluted from the cartridges and filters. The other method uses liquid chromatography separation with hydride generation atomic fluorescence detection to determine soluble arsenic species. Analysis of acidified water samples using inductively coupled plasma mass spectrometry provided the total arsenic concentration. Arsenic concentrations in water samples from the 120 wells ranged from <1 to ∼1000 μg L⁻¹. On average, particulate arsenic accounted for 39 ± 38% (median 36%) of the total arsenic. In some wells, particulate arsenic was six times higher than the soluble arsenic concentration. Particulate arsenic can be effectively removed using membrane filtration. The information on particulate and soluble arsenic in water is useful for optimizing treatment options and for understanding the geochemical behavior of arsenic in groundwater.     

Non-chromatographic speciation of toxic arsenic in vegetables by hydride generation-atomic fluorescence spectrometry after ultrasound-assisted extraction

A non-chromatographic, sensitive and simple analytical method has been developed for the determination of toxic arsenic species in vegetable samples by hydride generation-atomic fluorescence spectrometry (HG-AFS). As(III), As(V), dimethylarsinic acid (DMA) and monomethylarsonic acid (MMA) were determined by hydride generation-atomic fluorescence spectrometry using a series of proportional equations. The method is based on a single extraction of the arsenic species considered from vegetables through sonication at room temperature with H(3)PO(4) 1 mol L(-1) in the presence of 0.1% (w/v) Triton XT-114 and washing of the solid phase with 0.1% (w/v) EDTA, followed by direct measurement of the corresponding hydrides in four different experimental conditions. The limit of detection of the method was 3.1 ng g(-1) for As(III), 3.0 ng g(-1) for As(V), 1.5 ng g(-1) for DMA and 1.9 ng g(-1) for MMA, in all cases expressed in terms of sample dry weight. Recovery studies provided percentages greater than 91% for all considered species in spiked samples of chards and aubergines. Total toxic As found in the aforementioned samples was at the level of 90 ng g(-1); As(III) is followed by As(V), DMA and MMA which are the main species of As in chards being As(V) the main As compound in aubergines.     

Automated system for on-line determination of dimethylarsinic and inorganic arsenic by hydride generation–atomic fluorescence spectrometry

A multisyringe flow-injection approach has been coupled to hydride generation-atomic fluorescence spectrometry (HG-AFS) with UV photo-oxidation for dimethylarsinic (DMA), inorganic As and total As determination, depending on the pre-treatment given to the sample (extraction or digestion). The implementation of a UV lamp allows on-line photo-oxidation of DMA and the following arsenic detection, whereas a bypass leads the flow directly to the HG-AFS system, performing inorganic arsenic determination. DMA concentration is calculated by the difference of total inorganic arsenic and measurement of the photo-oxidation step. The detection limits for DMA and inorganic arsenic were 0.09 and 0.47 μg L(-1), respectively. The repeatability values accomplished were of 2.4 and 1.8%, whereas the injection frequencies were 24 and 28 injections per hour for DMA and inorganic arsenic, respectively. This method was validated by means of a solid reference material BCR-627 (muscle of tuna) with good agreement with the certified values. Satisfactory results for DMA and inorganic arsenic determination were obtained in several water matrices. The proposed method offers several advantages, such as increasing the sampling frequency, low detection limits and decreasing reagents and sample consumption, which leads to lower waste generation.     

氢化物发生-原子荧光光谱法同时测定水中砷和锑

建立在硝酸介质中用氢化物发生-原子荧光光谱法同时测定水中砷和锑的方法。优化了仪器工作条件、酸度、硼氢化钾及还原剂浓度。砷、锑的线性范围为0～10．0μg／L;检出限分别为0．02,0．01μg／L;测定结果的相对标准偏差分别为1．77％～3．72％,2．95％～4．87％（n=6）;加标回收率分别为98％106％,96％105％。该法操作简便,灵敏度高,快速,便于推广,适用于水中砷和锑的同时测定。     

顺序注射氢化物发生-原子荧光光谱法同时测定中草药中As和Bi

建立了一种顺序注射氢化物发生-原子荧光光谱法同时测定中草药中的As和Bi含量的方法,考察了光电倍增管负高压、As和Bi灯电流、原子化器高度、载气流量、屏蔽气流量等因素对测定结果的影响。结果表明,载流HCl的浓度为0.3 mol/L,KBH4质量浓度为10 g/L时,同时测定As和Bi的效果最佳;在最佳实验条件下,As和Bi的检出限分别为0.058μg/L和0.006μg/L,加标回收率为94.6%~103.2%,相对标准偏差小于3.0%,中草药试样中共存的离子对As和Bi的测定没有干扰。该法操作方便、快速,用于中草药中As和Bi的同时测定,具有很好的可行性和实用性。     

HPLC-ICP-MS测定植物样品中6种砷形态化合物

通过优化色谱分离、样品前处理条件,同时对比了电感耦合等离子体质谱的标准模式(STD)、碰撞模式(KED)、氧气反应模式(Oxygen-DRC)、甲烷反应模式(Methane-DRC)的检测结果,建立了一种有效分离植物样品中砷甜菜碱(AsB)、二甲基砷酸(DMA)、亚砷酸(As(Ⅲ))、砷胆碱(AsC)、一甲基砷酸(MM...     

Spectrophotometric determination of arsenic in water samples based on micro particle formation of ethyl violet-molybdoarsenate.

In this study, a simple and sensitive method for the determination of arsenic in water samples was developed. The method is based on the formation of micro particles of Ethyl Violet and molybdoarsenate, which gives an apparently homogeneous blue color to the solution. The absorption of the excess dye gradually decreases due to its conversion to a colorless carbinol species under strongly acidic conditions. Consequently, the sufficiently low reagent blank enables the spectrophotometric determination of arsenic with the detection limit of 4 microg l(-1). The coefficient of variation for the spectrophotometry at 50 microg l(-1) was 3.5% (n = 5). Furthermore, it is possible to detect concentrations as low as 10 microg l(-1) of arsenic visually. Our method will be useful as a simple, rapid, and cost-effective field test of arsenic, requiring no complex apparatus or skilled laboratory support.     

A chemical enhancement method for the spectrophotometric determination of trace amounts of arsenic

A highly sensitive spectrophotometric method for the determination of 0.03-1.0 microg of arsenic is described. After extraction as AsI(3) into benzene, it is selectively stripped into water. Both the arsenic(III) and iodide present in the aqueous phase are made to react with iodate in acidic medium in the presence of chloride to form the anionic chloro complex, ICl(-)(2). The determination is completed after extraction of ICl(-)(2) species as an ion-pair with Rhodamine 6G into benzene and measuring the absorption of the extract at 535 nm. The coefficient of variation is 1.5% for 10 determinations of 0.5 microg of arsenic. The method has been applied to the determination of arsenic content in plant materials, high purity iron, copper base alloys and inorganic arsenic levels of natural waters.     

Determination of arsenic in seafood by focused microwave digestion and hydride generation-atomic fluorescence detection

A new method was developed for total arsenic determination in seafood products such as oysters, mussels, tuna fish, and algae. Matrix decomposition and oxidation to arsenate of all the arsenic compounds in the product were completed in 25 min by using a 3-step program of focused microwaves (40-120 W) with nitric and sulfuric acids. Quantitation was performed by hydride generation-atomic fluorescence detection (HG-AFS). Results of method optimization are presented and discussed. A detection limit <125 microg/kg arsenic was obtained; the quantitation limit was close to 400 microg/kg, with repeatability and reproducibility <5% relative standard deviation. Validation was performed by analyzing 4Reference Materials (arsenic concentration expressed as mg/kg): The National Institute of Standards and Technology SRM 1566a Oyster tissue (14.0 +/- 1.2); the Bureau Community of Reference (now Standard Measurements & Testing Program) CRM 278 Mussel tissue (5.9 +/- 0.2) and CRM 627 Tuna fish (4.8 +/- 0.3); and the International Atomic Energy Agency RM 140 Fucus sample (44.3 +/- 2.1).     

正丁醇萃取-原子荧光光谱法间接测定茶叶中的钼

建立了正丁醇萃取原子荧光光谱法间接测定茶叶中钼的方法。基于As?和钼酸铵在0.3 mol/LH2SO4介质中能形成砷钼杂多酸,且形成的杂多酸可以被有效地萃取到有机溶剂中,原子荧光光谱法直接测定有机相中的砷,间接得到钼的含量。在优化的实验条件下,钼含量在0.09～15.0-g/L范围内呈良好的线性关系,方法的检出限是0.09-g/L,相对标准偏差为2.3%,据此对不同茶叶样品进行分析,加标回收率为95.2%～96.9%。本方法对茶叶中Mo的检测结果与电感耦合等离子体原子发射光谱法相符合。     

微波辅助消解-原子荧光法测定玻璃中的镉砷铅

光学玻璃中的各种元素对玻璃的光学性能有不同的影响。如加入镉可以提高玻璃折射率;砷的引入能增加玻璃的透光度,含铅玻璃具有低成本、高折射性等优点。但是镉、砷、铅均为有毒元素,玻璃加工和处理过程以及毒废弃物的处理都可能引起水、土壤、大气的污染并给人体带来一定的危害     

密闭罐溶样–氢化物发生–原子荧光光谱法测定中药中的汞和砷

建立了密闭罐溶样–氢化物发生–原子荧光光谱法测定中药中痕量汞和砷的分析方法。采用密闭罐溶解复杂基体中药样品,进行易挥发元素分析的样品前处理,技术简单,快速,能耗低。汞和砷的质量浓度分别在0~10μg/L和0~200μg/L范围内与荧光强度成线性关系,线性相关系数均大于0.99。汞、砷的检出限分别为0.014,0.086μg/L;测定结果的相对标准偏差不大于4.67%(n=5);加标回收率分别为99.0%~106.4%,95.2%~101.7%。该方法操作简便,可用于中药中汞、砷元素的质量控制。     

Separation and determination of arsenic species in water by selective exchange and hybrid resins

A simple and efficient method for separation and determination of inorganic arsenic (iAs) and organic arsenic (oAs) in drinking, natural and wastewater was developed. If arsenic is present in water prevailing forms are inorganic acids of As(III) and As(V). oAs can be found in traces as monomethylarsenic acid, MMA(V), and dimethylarsenic acid, DMAs(V). Three types of resins: a strong base anion exchange (SBAE) and two hybrid (HY) resins: HY-Fe and HY-AgCl, based on the activity of hydrated iron oxides and a silver chloride were investigated. It was found that the sorption processes (ion exchange, adsorption and chemisorptions) of arsenic species on SBAE (ion exchange) and HY resins depend on pH values of water. The quantitative separation of molecular and ionic forms of iAs and oAs was achieved by SBAE and pH adjustment, the molecular form of As(III) that exists in the water at pH <8.0 was not bonded with SBAE, which was convenient for direct determination of As(III) concentration in the effluent. HY-Fe resin retained all arsenic species except DMAs(V), which makes possible direct measurements of this specie in the effluent. HY-AgCl resin retained all iAs which was convenient for direct determination of oAs species concentration in the effluent. The selective bonding of arsenic species on three types of resins makes possible the development of the procedure for measuring and calculation of all arsenic species in water. In order to determine capacity of resins the preliminary investigations were performed in batch system and fixed bed flow system. Resin capacities were calculated according to breakthrough points in a fixed bed flow system which is the first step in designing of solid phase extraction (SPE) module for arsenic speciation separation and determination. Arsenic adsorption behavior in the presence of impurities showed tolerance with the respect to potential interference of anionic compounds commonly found in natural water. Proposed method was established performing standard procedures: with external standard, certified reference material and standard addition method. Two analytical techniques: the inductively coupled plasma mass spectrometry (ICP-MS) and atomic absorption spectroscopy-hydride generation (AAS-GH) were comparatively applied for the determination of arsenic in all arsenic species in water. ICP-MS detection limit was 0.2 μg L⁻¹ and relative standard deviation (RSD) of all arsenic species investigated was between 3.5 and 5.1%.