减反射膜对摄影镜头彩色还原特性的贡献

本文从彩色摄影的需要出发,根据美国的ANSI彩色标准,讨论了摄影镜头的彩色还原问题。文中指出镜头玻璃的光谱吸收对其彩色平衡的影响,着重分析了减反射膜对改善镜头彩色还原性能的作用,计算了各类减反射膜的彩色贡献,给出了用于10倍变焦距彩色摄影镜头减反射膜系的设计思想、计算方法和结果.结果表明:合理地选择减反射膜系可使镜头的透过率和彩色还原特性同时获得改善.     

彩色透明微晶玻璃的吸收光谱

在Li2O-Al2O3-SiO2系统玻璃中掺入少量晶核剂TiO2,ZrO2,P2O5，再掺入稀土离子和过渡金属离子作为着色剂，在高温下溶制得到彩色透明玻璃，对上述玻璃进行微晶化处理，用差热分析（DTA）确定其晶化温度，测定与讨论了所获彩色透明微晶玻璃在紫外波段至近红外波段的吸收光谱特性，研究结果表明，玻璃微晶化后，由于基质玻璃对光的微弱散射，引起吸收的增强，但不改变稀土离子和过渡金属离子的本征吸收峰位。     

高压作用下相分离液体玻璃转变的分子动力学研究

采用分子动力学模拟方法,研究了二元混合液体在不同外压作用下的相分离与玻璃转变过程,计算了相分离液体在玻璃转变过程中的结构和动力学特征.研究发现,外压会促进相分离的产生,并提高玻璃转变温度,会使β弛豫出现的温度更高、存在的时间更长,导致系统扩散性降低.同时还发现,相分离液体的玻璃转变过程存在微观不均匀现象. 关键词： 相分离 玻璃转变 分子动力学模拟 外压影响     

相干彩虹的形成机制

用一束白光激光聚焦照射液体(水、丙酮、无水乙醇、汽水等)或固体(冰、有色玻璃、塑料、彩色蜡等),出现了多级的彩色干涉环,即相干彩虹.高强度白光局部地加热了液体(固体),改变了它的密度(以及折射性质),从而导致光程差的出现,不同波长的光都发生干渉,形成了彩色的干涉环.有色玻璃在反射模式下也出现了相干彩虹,此时的干涉完全来自于玻璃表面轮廓的变化,并且无参数拟合的结果定量地符合观测到的干涉图案.     

分子动力学模拟钠硼硅酸盐玻璃电子辐照诱导的结构演化效应

钠硼硅酸盐玻璃作为高放射废物玻璃固化体的候选材料之一,已有大量实验对该类玻璃开展了电子或重离子的辐照效应研究.然而,在理论计算与模拟方面的工作却很少,目前主要集中于重离子的辐照效应,对电子的辐照效应的模拟尚未见报道.本文利用分子动力学工具提出一种新的方法,以实现对电子辐照诱导的玻璃结构演化进行模拟.该方法基于实验中玻璃的结构变化特点,即实验中的拉曼结果已经证实:在大剂量的电子辐照后的玻璃中存在分子氧的事实,由于这些分子氧不会与其他粒子发生相互作用,因而可以通过从体系中逐步地移除一定数量氧原子的方式,以达到模拟大剂量电子辐照的情形,进而得到电子辐照后的玻璃的结构信息.模拟结果显示:随着移除氧原子的数量增加,玻璃中的Si—O—Si平均键角逐渐减小;而且玻璃中的小环数量会因氧的逐渐减少而逐渐增加;玻璃中部分[BO4]结构会转变为[BO3]结构,最终这种转变会达到饱和;大量移除氧之后,玻璃中的钠元素也出现明显的相分离.这些模拟辐照的玻璃结构特性能较好地与实验中的硼硅酸盐玻璃电子辐照诱导的结构变化符合.因此,本文提出的方法有望为通过分子动力学模拟硼硅酸盐玻璃的电子辐照效应提供新思路.     

彩色多晶硅太阳电池性能研究

通过调节单层SiN_x:H减反射膜的厚度制备各种颜色的多晶硅太阳电池. 测试了太阳电池片和组件的光学和电学性能, 用PC1D软件对其性能进行模拟. 通过分析得到以下结论: 1)当减反射膜的厚度小于50 nm时, 影响彩色组件和电池片功率变化的主要因素是开路电压(V_oc)和短路电流(I_sc), 当减反射膜的膜厚度大于50 nm时, 随着减反射膜钝化作用的稳定, 影响彩色组件和电池片功率变化的主要因素是I_sc; 2)大多数彩色电池片的效率比传统蓝色电池片的效率低, 但是在封装之后, 彩色电池组件可以有不同程度的增益, 主要原因是减反射膜与乙烯-醋酸乙烯共聚物和玻璃匹配性较好. 关键词： 彩色太阳电池 氮化硅 钝化 光学匹配     

金属玻璃流变的扩展弹性模型

玻璃-液体转变现象,简称玻璃转变,被诺贝尔物理学奖获得者安德森教授评为最深奥与重要的凝聚态物理问题之一.金属玻璃作为典型的非晶态物质,具有与液体相似的无序原子结构,因此又称为冻结了的液态金属,是研究玻璃转变问题的理想模型材料.当加热至玻璃转变温度,或者加载到力学屈服点附近时,金属玻璃将会发生流动.由于热或应力导致的流动现象对金属玻璃的应用具有重要意义.本文简要回顾了金属玻璃流变现象,综述了流变扩展弹性模型的研究进展和未来发展趋势.     

应用光学——光学系统设计指南 第十章 光学介质(续)

10.1.4 化学和辐射效应硅酸盐玻璃一般有较强的抗化学作用。尽管如此,但它们还是会受某些因素的影响,使其表面损坏。下面列出了这种损坏的某些最常见的原因: 1.碱溶液和稀释氢氟酸会使Si—O键断开,并缓慢分解玻璃。 2.酸溶液可能在玻璃表面上由氢取代碱,因而可能导致表面上形成低折射率的膜层。虽然它对玻璃的外观有些损害,但这种染色在实用上却是有益的,因为它起着低反射涂层的作用。     

掺Yb硅酸盐玻璃的热漂白性能研究

采用传统高温熔融法制备了掺Yb硅酸盐玻璃, 玻璃组成为 60SiO₂-12Al₂O₃-28CaO-1.0 mol%Yb₂O₃. 将玻璃分成两组, 一组经总剂量3 kGy的Co⁶⁰γ辐射源辐射, 另一组做空白对照. 然后测试了玻璃未辐射、辐射后及热漂白后的吸收谱和近红外发光谱. 实验结果表明: 一定的热处理会使得玻璃在辐射过程中产生的色心缺陷发生分解, 即辐射后的玻璃在300–900 nm波段的吸收系数显著地降低了, 在400 nm处未经辐射、经3 kGy辐射以及热漂白后的玻璃吸收系数分别是0.93, 2.9, 1.89 cm^-1. 另外, 玻璃的近红外发光强度明显增强, 在1028 nm处未经辐射、经3 kGy辐射以及热漂白后的玻璃近红外发光相对强度分别是588, 261, 436, 从而极大地改善了玻璃的光学性能. 所以一定的热处理可以使辐射后的玻璃产生热漂白的现象. 研究结果为进一步发展抗辐射玻璃材料提供了新的实验依据.     

激光窃听实验探究

提出了一种激光窃听模型,并简要地介绍了其实现方法.声音信号在玻璃表面会产生声压,驱动玻璃做受迫振动,使其在激光入射点附近做近似垂直振动.玻璃的微小位移使得反射激光的光轴也发生相应线性的位移.在接收端,通过探测射到光电检测器窗口的光斑面积的变化,可将光信号转变为电信号,再经过放大等处理,实现声音的还原,达到窃听的效果.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.