微波晶体检波二极管检波特性的分段定标

本文阐述了利用驻波法对微波晶体检波二极管进行分段定标的方法。利用线性回归法将微波测量系统中驻波幅度自波节到波腹进行分段定标,得到每段的检波律。     

用天线阵测量圆柱过模波导中虚阴极振荡器产生的高功率微波模式和功率

介绍在圆柱过模波导中虚阴极振荡器产生高功率微波实验中用天线阵测量微波模式的原理和方法。测量微波模式对研究高功率微波产生的机理具有重要意义。结合在圆柱过模波导壁上安装小电探针天线和小磁环天线测量微波模式的方法,用天线阵测量圆柱过模波导中开口辐射的电磁场空间分布。应用最小二乘法优化原理拟合高功率微波模式功率分布。用天线阵测量了圆柱过模波导中虚阴极振荡器产生高功率微波混合模式功率分布。     

定向耦合法测量非标准接口元件驻波系数

 利用网络分析仪,根据需要在设定的频率范围进行扫频测量,网络分析仪的端口1输出的微波信号经过微波传输转换器进入与待测非标准元件匹配连接的连接段（如波导）;网络分析仪的端口2连接定向耦合器,用于监测传输段内的反射微波信号。首先,在非标准接口端面连接短路面,通过网络分析仪测量反射信号在设定频点的相对幅度值;然后去掉短路面,在非标准接口端面连接待测元件,再次测量反射信号在特定频点的相对幅度值;最后根据本文推导的公式得出驻波系数。该方法的测量误差与定向耦合器的方向性（方向性系数越大越好）和待测元件驻波系数有关。将该方法运用在非标准接口匹配负载驻波系数的测量中,定向耦合器方向性系数取为40 dB,测得其驻波系数小于1.2,误差小于20%。该方法简便可行,可以用于测量常用的非标准接口元件尤其是非标准低驻波系数元件的驻波系数。     

定向耦合法测量非标准接口元件驻波系数

利用网络分析仪,根据需要在设定的频率范围进行扫频测量,网络分析仪的端口1输出的微波信号经过微波传输转换器进入与待测非标准元件匹配连接的连接段（如波导）;网络分析仪的端口2连接定向耦合器,用于监测传输段内的反射微波信号。首先,在非标准接口端面连接短路面,通过网络分析仪测量反射信号在设定频点的相对幅度值;然后去掉短路面,在非标准接口端面连接待测元件,再次测量反射信号在特定频点的相对幅度值;最后根据本文推导的公式得出驻波系数。该方法的测量误差与定向耦合器的方向性（方向性系数越大越好）和待测元件驻波系数有关。将该方法运用在非标准接口匹配负载驻波系数的测量中,定向耦合器方向性系数取为40 dB,测得其驻波系数小于1.2,误差小于20%。该方法简便可行,可以用于测量常用的非标准接口元件尤其是非标准低驻波系数元件的驻波系数。     

驻波法测超声波衰减系数

用驻波法测量超声波在空气中衰减系数的实验方法。与前人的方法进行比较。新的测量结果更符合实际。只有当换能器反射系数r〈0.619时,用简单波拟合得到的衰减系数才比较可信。同时讨论了该方法的实用意义。     

三维超声驻波场的数字全息测量与重建研究

利用数字全息干涉术研究了超声驻波场的三维分布特征,由所记录的不同角度的超声驻波场的数字全息图,经数值再现,得到了超声驻波场的强度和相位差分布图,进而由迭代重建算法重建出超声驻波场的三维分布曲线。结果表明,数字全息干涉术与迭代重建算法相结合是测量与重建三维超声驻波场的一种方便有效方法。     

砷化镓半导体材料与器件中高频场分布研究的新方法——脉冲电光检测技术

介绍了砷化镓材料和器件中高频电场的分布测量的新方法——谐波混频脉冲电光检测:它的原理、实验装置以及在砷化镓共平面波导中微波驻波场分布测量中应用的结果.在频率高达20.10GHz及开路、短路和50Ω不同的负载条件下测得的结果与理论预计值符合很好.本文最后对方法的灵敏度和空间分辨率进行讨论.     

C波段2 MeV驻波加速管物理设计

 为了发展结构紧凑、小束斑加速器,进行了C波段驻波电子直线加速器加速管的物理设计和研究。利用多级聚束和大孔径注入方法,抑制空间电荷效应。加速管由3个聚束腔和4个加速腔组成,长约163 mm,馈入微波功率源1 MW。在最终的数值模拟中,得到脉冲电流约150 mA,俘获效率优于30％,在加速管出口外约14 mm处,对电子的横向分布进行非线性Gauss拟合,得到束斑直径（FWHM）约为0.55 mm。     

C波段2 MeV驻波加速管物理设计

为了发展结构紧凑、小束斑加速器,进行了C波段驻波电子直线加速器加速管的物理设计和研究。利用多级聚束和大孔径注入方法,抑制空间电荷效应。加速管由3个聚束腔和4个加速腔组成,长约163 mm,馈入微波功率源1 MW。在最终的数值模拟中,得到脉冲电流约150 mA,俘获效率优于30％,在加速管出口外约14 mm处,对电子的横向分布进行非线性Gauss拟合,得到束斑直径（FWHM）约为0.55 mm。     

S波段2MeV轴耦合驻波加速管参数冷测调试

介绍了用于工业CT的S波段2MeV驻波电子直线加速管的微波冷测及调整,并详细描述了加速管频率的测量与调谐,加速管与矩形波导匹配,加速管品质因数及加速管整管场分布的测量,给出了加速管微波调试及调整的结果.结果如下:加速管的频率一致性达到±0.3MHz以内,过饱和状态下的耦合度为1.14,加速管单腔的品质因数约为120004-200,场分布的比值1:2.2:2.结果表明微波调试满足物理设计的要求.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.