Use of Retention Data as the First Step in the Identification of Cyclic Organic Peroxides in Temperature-Programmed Gas Chromatography

Temperature-programmed retention indices for eleven cyclic organic peroxides were determined by gas chromatography on slightly polar 5% biphenyl 95% dimethylpolysiloxane columns (DB-5 and Rtx-5MS) at three heating rates (5, 10, and 20° min⁻¹) from 60 to 300°C, using different chromatographs. Cyclic organic diperoxides and triperoxides had nearly constant retention indices when different heating rates and a short isothermal hold time (5 min) before the programmed increase in temperature were used. The usefulness of temperature-programmed retention indices was shown by using the data to predict the retention times and structures of unknown diperoxides or triperoxides derived from ketones. This is the first step in the identification of unknown cyclic organic peroxides, a process would otherwise require the availability of reference compounds. Revised: 7 and 17 November 2005     

Appraisal of an Empirical Model for Simulation of Retention from Structure in Temperature-Programmed Gas Chromatography

The solvation parameter model and response surface methodology are evaluated for the prediction of retention in temperature-programmed gas chromatography. A large and varied group of compounds were separated at a constant flow rate on three columns of different selectivity (DB-1701, DB-210 and EC-Wax) with initial temperature in the range 60–120 °C and program rates of 1–15 °C min^?1. The solvation parameter model provides an acceptable fit to the experimental retention factors independent of column identity, initial temperature and program rate. The system coefficients of the solvation parameter model are shown to fit a second order program rate model of the form system coefficient = a_o + a₁ X + a₂ X ² where X is the program rate (°C min^?1) and a_o, a₁ and a₂ are fitting coefficients with no physical significance. Response surface methodology was used to derive empirical models to predict system coefficients with program rate and initial temperature as variables. These models explain the experimental data quite well but are local models that depend on the average properties of the solutes used for their derivation. Since they dependent on solute identity, these models are unsuitable for the general prediction of retention from structure, but may prove useful for estimating retention associated with variation in experimental variables for a defined group of compounds.     

Evaluation of the Linear-Elution-Strength Model for the Prediction of Retention and Selectivity in Isothermal Gas Chromatography

Linear-elution strength theory and temperature-programmed gas chromatography is evaluated as a rapid method for predicting isothermal retention factors and column selectivity. Retention times for a wide range of compounds are determined at the program rates of 3 and 12 °C/min for the temperature range 60 to 160 °C on three open-tubular columns (DB-1701, DB-210 and EC-Wax) and used to predict isothermal retention factors for each column over the temperature range 60 to 140 °C. The temperature-program predicted isothermal retention factors are compared with experimental values using linear regression and the solvation parameter model. It is shown that isothermal retention factors predicted by the linear-elution-strength model only approximately represents the experimental data. The model fails to predict the slight curvature that exists in most plots of the experimental retention factor (log k) as a function of temperature. In addition, regression of the temperature-program predicted isothermal retention factors against the experimental values indicates that the slopes and intercepts deviate significantly from their target values of one and zero, respectively, in a manner which is temperature dependent. The temperature-program predicted isothermal retention factors result in system constants for the solvation parameter model that are different to those obtained from the experimental retention factors. These results are interpreted as indicating that linear-elution-strength theory predicts retention factors that fail to accurately model stationary phase interactions over a wide temperature range. It is concluded that temperature-program methods using linear-elution-strength theory are unsuitable for constructing system maps for isothermal separations.     

Retention time prediction of compounds in Grob standard mixture for apolar capillary columns in temperature-programmed gas chromatography

This paper presents an extension of a previous investigation in which the behavior of nonpolar compounds in temperature-programmed gas chromatographic runs was predicted using thermodynamic (entropy and enthalpy) parameters derived from isothermal runs. In a similar manner, entropy and enthalpy parameters were determined for a Grob standard mixture of compounds with widely varying chemical characteristics. These parameters were used to predict the retention times and chromatographic behaviors of the compounds on four gas chromatography capillary columns: three that had phenyl-based stationary phases (with degrees of substitution of 0%, 5% and 50%) and one with (50%) cyanopropyl substitution. The predictions matched data empirically obtained from temperature-programmed chromatographic runs for all of the compounds extremely well, despite the wide variations in polarity of both the compounds and stationary phases. Thus, the results indicate that such simulations could greatly reduce the time and material costs of chromatographic optimizations.     

Calculation of retention indices at an assigned temperature from temperature-programmed data

Summary A method is presented for the calculation of retention indices at an assigned temperature from temperature-programmed data. If the retention times at two different program rates for the solutes and the n-alkanes are known, the retention indices at an assigned temperature can be calculated directly.     

Temperature-programmed retention indices for gas chromatography-mass spectroscopy analysis of plant essential oils

A total of 95 volatile compounds from the essential oil in buds of Syringa oblata Lindl (lilac) were identified by gas chromatography-mass spectrometry (GC-MS) combined with heuristic evolving latent projections (HELP) and moving subwindow searching (MSS). The identified compounds are mainly aliphatic, terpenes and aromatic compounds. Their temperature-programmed retention indices (PTRIs) on HP-5MS and DB-35MS at three heating rates of 2, 4 and 6 degrees C/min from 80 to 290 degrees C were obtained, which showed that aliphatic compounds give nearly constant PTRIs and PTRIs of terpenoids do not vary much at different heating rates. But PTRIs of aromatic compounds exhibit relatively large temperature dependence. PTRIs vary much more on DB-35MS than those on HP-5MS according to the compound types. In general, differences of PTRIs between the two columns increase from aliphatic compounds to terpenoids to polycyclic aromatic compounds. The PTRIs in different heating rates were used as cross-references in the identification of components in the essential oil. When they were used in analysis of essential oil from flowers of lilac, good results were obtained. These PTRIs would be a part of our PTRI database being constructed on components from plant essential oils. The results also showed that efficiency and reliability were improved greatly when chemometric method and PTRIs were used as assistants of GC-MS in identification of chemical components in plant essential oils.     

Assessment of the selectivity equivalence of DB-608 and DB-624 open-tubular columns for gas chromatography

The solvation parameter model is used to characterize the selectivity of DB-608 and DB-624 open-tubular columns at five equally spaced temperatures over the range 60 to 140 degrees C. The system constants for the DB-608 and DB-624 columns were used as selectivity parameters to search a database of open-tubular columns to identify columns with similar selectivity. The search was refined using the absolute deviation of the system constants and retention factor regression models for varied compounds. For method development it is shown that the selectivity of the poly(cyanopropylphenyldimethylsiloxane) stationary phase containing 6% cyanopropylphenylsiloxane monomer (DB-1301) is equivalent to DB-624 and the poly(dimethyldiphenylsiloxane) stationary phases containing either 50 or 65% diphenylsiloxane monomer (Rtx-50 and Rtx-65) are suitable choices for DB-608.     

Comparing columns for gas chromatography with the two-parameter model for retention prediction

The retention times of selected compounds in temperature programmed gas chromatography were predicted using a two-parameter model, on the basis of thermodynamic data obtained from isothermal runs on seven capillary columns, primarily substituted with 5% diphenylsiloxane. The scope for using thermodynamic data obtained from isothermal runs on one column to optimize separation on a different column or a different instrument setup was investigated. Additionally, the predictive utility of thermodynamic data obtained using a DB-5 column that had been in use for three years was compared to that of a new column of the same model. It was found that satisfactory separation could be achieved on one capillary column or instrument setup on the basis of thermodynamic data obtained using a different column or instrument set-up.     

西兰花中13种有机含磷农药在不同色谱柱上的色谱保留行为

应用Agilent GC 6890气相色谱仪(附FPD检测器)对13种残留于西兰花中的有机含磷农药(OPP′s)在4种不同极性的毛细管色谱柱(即DB-1、DB-5、DB-1701及DB-35MS)上的保留行为作了研究。结果表明:采用由DB-5及DB-1701串联组成的色谱柱单元,西兰花中13种残留OPP′s可达到有效分离和测定。     

A new gas chromatographic retention index for pesticides and related compounds

A new gas chromatographic (GC) retention index based on a homologous series of tri-n-alkylamines is proposed for use in the detection of pesticides and related compounds because the standard n-paraffin hydrocarbons used for the Kovats index do not show up well on the nitrogen-phosphorus detectors commonly used in pesticide analysis. Using fused silica bonded phase capillary columns (DB-1 or DB-5), the trialkylamine indices of 106 selected pesticides and related compounds were measured and their relationship to the Kovats index determined.     

System for calculating the linear temperature-programmed retention indices of polycyclic aromatic compounds

Theoretical procedures have been used to predict linear temperature-programmed retention indices for polycyclic aromatic compounds. It is possible to calculate such indices for polycyclic aromatic compounds in some practical situations in which the compounds cannot be eluted during a simple linear temperature program. The theory has been tested for a number of polycyclic aromatic hydrocarbon (PAHs) in single- and multi-plateau temperature-programmed gas chromatography with SE-52 as the stationary phase. This method will extend the applicability of linear retention indices for the identification of the isomers of polycyclic aromatic compounds.     

Evaluation of the separation characteristics of application-specific (volatile organic compounds) open-tubular columns for gas chromatography

The solvation parameter model is used to characterize the separation characteristics of two application-specific open-tubular columns (Rtx-Volatiles and Rtx-VGC) and a general purpose column for the separation of volatile organic compounds (DB-WAXetr) at five equally spaced temperatures over the range 60-140 degrees C. System constant differences and retention factor correlation plots are then used to determine selectivity differences between the above columns and their closest neighbors in a large database of system constants and retention factors for forty-four open-tubular columns. The Rtx-Volatiles column is shown to have separation characteristics predicted for a poly(dimethyldiphenylsiloxane) stationary phase containing about 16% diphenylsiloxane monomer. The Rtx-VGC column has separation properties similar to the poly(cyanopropylphenyldimethylsiloxane) stationary phase containing 14% cyanopropylphenylsiloxane monomer DB-1701 for non-polar and dipolar/polarizable compounds but significantly different characteristics for the separation of hydrogen-bond acids. For all practical purposes the DB-WAXetr column is shown to be selectivity equivalent to poly(ethylene glycol) columns prepared using different chemistries for bonding and immobilizing the stationary phase. Principal component analysis and cluster analysis are then used to classify the system constants for the above columns and a sub-database of eleven open-tubular columns (DB-1, HP-5, DB-VRX, Rtx-20, DB-35, Rtx-50, Rtx-65, DB-1301, DB-1701, DB-200, and DB-624) commonly used for the separation of volatile organic compounds. A rationale basis for column selection based on differences in intermolecular interactions is presented as an aid to method development for the separation of volatile organic compounds.     

Separation characteristics of phenyl-containing stationary phases for gas chromatography based on silarylene-siloxane copolymer chemistries

The solvation parameter model is used to characterize the retention properties of five open-tubular column stationary phases (ZB-5 ms, DB-5 ms, DB-XLB, DB-17 ms, and DB-35 ms) based on silarylene-siloxane copolymer chemistries at five equally spaced temperatures over the range 60-140 degrees C. System constant differences and regression models for varied compounds are used to establish the selectivity equivalence of the silarylene-siloxane copolymer stationary phases and to compare their separation characteristics with poly(dimethyldiphenylsiloxane) stationary phases containing a nominally similar concentration of phenyl groups. These studies demonstrate that ZB-5 ms and DB-5 ms are selectivity equivalent. DB-XLB is significantly more dipolar and polarizable than DB-5 ms. In general terms, the silarylenesiloxane copolymer stationary phases are slightly less cohesive and more dipolar and polarizable with similar hydrogen-bond basicity to the poly(dimethyldiphenylsiloxane) stationary phases they were designed to replace. None of the silarylenesiloxane copolymer or poly(dimethyldiphenylsiloxane) stationary phases are hydrogen-bond acidic. Selectivity differences between the two types of stationary phase are temperature dependent and tend to be smaller at higher temperatures within the temperature range studied. Consequently, selectivity differences cannot be globalized without reference to the temperature for the comparison.     

Gas chromatographic study of acetyl derivates of chlorinated guaiacols

Summary The gas chromatography of acetyl derivatives of guaiacol and all chlorinated guaiacols has been studied on SE-30, OV-351 and Carbowax 20M capillary columns. The retention order and relative retention times under isotermal and temperature-programmed conditions are discussed. Different retention times for all mono- and dichloro compounds have been observed on the SE-30 column. However, all trichloroguaiacol isomers were separated only on polar columns. The best overall temperature-programmed separations have been achieved on an SE-30 capillary column.     

Origin and correction of the deviations in retention times at increasing flow rate with Chromolith columns

Chromoliths can be used at flow rates beyond those feasible for conventional microparticulate packed columns. Ideally, the plots of the retention time versus the inverse of delivered flow rate should exhibit y-intercept of zero. However, significant positive deviations correlating with the solute polarity were observed for several compounds chromatographed with a Chromolith column, owing to the increased system pressure. Consequently, the dead time marker exhibits a smaller deviation, making the retention factors depend on the flow rate. Chromoliths are made of a silica-based monolith encapsulated within a PEEK tube, and should suffer larger stress with pressure than stainless steel columns, tending to inflate them and increase their volume. This decreases the linear velocity inside the column, and increases the retention at relatively low pressure (<200 bar). In contrast, frictional heating, which is an issue for microparticulate columns, seems to be less significant for the highly permeable Chromoliths. The usefulness of the retention time versus the inverse of the delivered flow rate plots to measure the deviations, whatever their origin, is shown. This allows the correction of the retention times to the ideal behaviour, where the retention factors are independent of the flow rate.     

Gas chromatographic optimization studies on the side chain and ring regioisomers of methylenedioxymethamphetamine

Gas chromatographic (GC) optimization studies are conducted for the 10 methylenedioxyphenethylamine regioisomeric substances related to the drug of abuse 3,4-methylenedioxymethamphetamine (MDMA, Ecstasy). These 10 compounds, having the same molecular weight and equivalent major mass spectral fragments, are not completely resolved using typical GC-mass spectrometry screening methods for illicit drugs. MDMA coelutes with at least one nondrug regioisomer under standard drug screening conditions. Separation of the 10 regioisomers is studied using stationary phases of varying polarities. Resolution optimization shows that very slow program rates give the best separation for the nonpolar stationary phases, requiring analysis times of as much as 85 min. Narrow-bore columns containing the same nonpolar stationary phases improve the analysis time to approximately 29 min. The polar stationary phase DB-35MS allows high-temperature programming rates, yielding complete resolution of all 10 compounds in less than 7 min. Temperature program optimization studies on the DB-35MS phase allow the separation time to be reduced to approximately 4.5 min.     

Study of the retention behavior of small polar molecules on different types of stationary phases used in hydrophilic interaction liquid chromatography

The retention behavior of a large group of analytes (35) with varied properties (pK_a and logP) was studied on eight hydrophilic interaction LC columns with different surfaces, stationary phase chemistries, and types of particles. The acetonitrile content (5–95%), buffer concentration (0.5–200 mM), and pH of the mobile phase (3.8 and 6.8) were evaluated for their effects on the retention behavior. The type of stationary phase had a significant impact on the selectivity and retention time of the tested analytes. Completely different selectivity was observed on the aminopropyl stationary phase. In this study, the influence of the buffer concentration was similar for all tested columns, except for the aminopropyl stationary phase. Increasing the buffer concentration led to decreased retention times for the basic compounds and increased retention times for the acidic compounds, while the inverse behavior was observed on the aminopropyl stationary phase. The selectivity of the individual stationary phases was evaluated at pH 3.8 and 6.8. Much lower selectivity differences between the stationary phases were observed at pH 6.8 than pH 3.8. Bare silica stationary phases were used in the comparison of the particles (fused‐core and fully porous particles of 3 and 1.7 μm) and the columns provided by different manufacturers.     

Determination of organochlorine pesticide residues by solid phase extraction and dual-column HRGC

Organochlorine pesticide residues have been extracted from samples of animal feed by a solid phase extraction clean-up procedure using an octadecyl-bonded column. The proposed method gave recoveries ranging from 70 to 100 % for ppb levels of the fifteeen pesticides studied. Analytes were identified by dual-column capillary gas chromatography employing DB-1 and DB-1701 columns in parallel; identities were confirmed by calculation of retention indexes with the cubic spline interpolation method.     

Evaluation of fused-silica capillary columns for GC/ECD analysis of chlorinated hydrocarbons listed in EPA method 8120

Four mega-bore, one wide-bore, and one narrow-bore fused-silica capillary columns were evaluated for their applicability to the GC/ECD analysis of 22 chlorinated hydrocarbons, some of which are currently targeted by EPA Method 8120. No one column can resolve all 22 compounds investigated here. Four compounds (two pairs) are coeluting on the SPB-35, DB-210, DB-WAX, and DB-519 fused-silica capillary columns, five compounds (two groups) are coeluting on the DB-1301 fused-silica capillary column, and ten compounds (five pairs) are coeluting on the SPB-5 fused-silica capillary column. The analysis time varies between 30 and 50 min. The order of elution of the chlorinated benzenes seems to depend on their boiling points rather than on the polarity of the liquid phase. The retention times of an additional nine chlorinated toluenes, eight chlorinated xylenes, and five chlorinated naphthalenes are also reported. Electron capture detector linearity is reported for the DB-210 fused-silica capillary column. Five brominated compounds were investigated as possible internal standards for Method 8120.