激光加热充氖靶丸的压缩实验研究

在神光(10¹²W)激光器上,用充Ne靶丸开展了内爆压缩实验研究。结果表明:实现了激光加热靶丸的对称性内爆压缩,芯部电子密度达10²³cm^-3,平均内爆速度为3.3×10⁷cm/。 关键词：     

激光烧蚀Al靶产生的等离子体中辐射粒子的速度及激波

在低真空条件下(5Pa),通过测量脉冲激光烧蚀平面Al靶产生的等离子体辐射谱的时间分辨特征,得到辐射粒子速度的空间分布.在激光脉冲宽度为10ns,烧蚀斑直径为200μm,靶面上功率密度分别为1.91×10¹⁰,5.10×10¹⁰和7.64×10¹⁰W/cm²时,测得辐射粒子Al的速度均在10⁶cm/s量级,且随着靶面径向距离的增大而近似呈指数衰减.在距靶面的相同距离处,激光功率密度的增大反而使速度减小.利用激波模型(shockwave model)较好地解释了实验结果,并得出激波的波面基本为柱对称 关键词： 激光等离子体 平面Al靶 粒子速度分布 激波     

激光加热Cu和NaF靶产生的1.2keV区X射线转换效率的测量

介绍了激光加热Cu靶和NaF靶发射的在1.2keV区X射线转换效率的测量方法和实验结果。结果表明,在激光辐照功率密度为1×10¹³—1×10¹⁴W·cm^-2条件下,激光波长为1.06μm或0.53μm时,Cu等离子体发射的1.2KeV区X射线的转换率为NaF等离子体的4—5倍;对此两种等离子体,激光波长为0.53μm的X射线转换效率是波长为1.06μm的2倍左右。 关键词：     

Mg微管靶喷口电子密度及X射线谱的时间分辨特性

1.06μm激光以3.5×10¹³W/cm²管壁辐照强度注入带侧向喷口Mg微管靶管内。利用X射线条纹相机测量Mg¹⁰⁺和Mg¹¹⁺离子沿侧喷方向发射X射线谱随时间变化过程,X射线时间分辨谱结果表明,三体再复合过程是实现Mg¹⁰⁺离子激发态1s4p和1s3p能级间粒子数反转的主要机制。用2660?紫外激光探针探测侧向喷口处等离子体电子密度,其密度值与用光谱分析获取的一致。 关键词：     

激光柱形腔靶的X射线温度和X射线转换效率

本文根据实验和数值模拟给出的信息,解析研究激光加热柱形腔靶(简称“腔靶”)X射线温度与激光转换的X射线能之间的定标规律,推断了1989年在神光激光器上做的系列腔靶实验,对于每束激光能量为300—500J,脉冲宽度为0.7—1.0ns,波长λ为1.06μm的高斯型激光源,双束靶的X射线转换效率约为(50—55)%,X射线温度为(1.5—1.7)×10⁶K。 关键词：     

针孔透射光栅谱仪用于线聚焦激光等离子体研究

利用针孔透射光栅光谱仪(PTGS)研究了波长为1.06μm、平均功率密度为2×10¹²W/cm²的线聚焦激光照射Al平板靶所产生的线状等离子体的轴向和非轴向X射线发射(5—200?)的光谱和空间分布特性。文中也就该条件下的线状等离子体作为X射线激光增益介质的有关问题进行了讨论。 关键词：     

现代物理信息

 1.D_?⁺的新衰变道.第一次观测到D_?⁺→ηρ⁺,η¹ρ⁺,确定了D_?⁺→φρ⁺.这些衰变方式的分支比,比D_?⁺→φπ⁺要大.（CLEO collaboration,No.9）2.新的质子放射同位素.用300MeV的⁵³Ni离子轰击¹⁰⁶Cd靶,经质量分离而得最重的放射质子同位素¹⁶⁰Re与¹⁵⁶Ta.测到放出质子的能量、总寿命和质子分支比,对¹⁶⁰Re是1261±6KeV、790±160μs和（91±10）%,对¹⁵⁶Ta是1022±13KeV、165_-55⁺¹⁶⁵ms和～100%.（R.D.Page et al.,No.9）3.飞秒激光产生MeV级能量的X射线0.5TW、120fs Ti:兰宝石激光照射到固体靶上,当聚焦达10¹⁸W/cm²时,产生的等离子体会放出能量超过1MeV的X射线.产额随入射激光功率的3/2而上升.40mJ激光打靶,X射线能量在20Key以上的能量转换达0.3%,X射线的能谱符合1/E分布.     

kHz激光与固体靶相互作用产生的X射线源

利用kHz激光与固体靶相互作用产生了平均流强为1.3×10⁷ photons·sr^-1·s^-1的X射线源, 研究了激光的对比度和能量对激光与固体靶相互作用产生的X射线能谱及K_α 产额的影响, 使用刀边成像技术测量了X射线源的源尺寸, 并进行了初步的成像实验. 实验中观察到对于非相对论级别的激光脉冲, 降低激光的对比度有利于提高K_α 产额, 而使用高对比度高强度激光, 更有利于获得高通量高信噪比X射线源. 关键词： kHz激光 固体靶 X射线     

激光等离子体辐射温度时间特性测量研究

本文提出一种软X射线条纹相机与吸收膜相耦合测量激光等离子体辐射温度的实验方法,并且应用这个方法测量了平面金靶在1.053μm激光(LF-11^#激光装置)作用下,靶面功率密度约为10¹⁴W/cm²的辐射温度。对温度处理中存在的误差,以及把此方法推广到能谱的时间分辨和温度的空间分辨测量中的可能性进行了讨论。 关键词：     

类氖锗的X射线激光增益及其传输特性研究

在神光(10¹²W)装置上,用1.06μm激光加热片状锗靶,用袖珍式掠入射光栅谱仪测量了类氖锗离子的3S—3P激光跃迁线的增益系数和X射线激光的传输特性,得到的结果为:波长为19.638,23.224,23.627,24.743和28.643nm的5条激光跃迁线的增益系数分别为3.06,3.99,3.72,2.36和4.59cm^-1;当等离子体长度为18mm时,相应的X射线激光的发散角约为12mrad,发射X射线激光的等离子体厚度约为200μm,X射线激光峰值强 关键词：     

Absolute spectral distribution of soft X-ray emission from laserproduced gold plasma

Quantitative measurement of spectral distribution of soft X-ray emission from laser produced plasmas and estimation of X-ray conversion efficiency are reported. The X-ray emission from planar gold target irradiated by an Nd:glass laser was recorded using a high resolution transmission grating spectrograph. Spectral distribution of X-ray intensity was derived using calibrated film data and a deconvolution procedure to account for contribution of higher diffraction orders. Results of conversion efficiency per unit solid angle, at a laser intensity of ~4×10¹² W/cm² (λ_L = 1.054 μm), for 10< λ <80 Å and in the water window spectral region (23< λ< 44 Å) are presented. A three-fold increase in conversion efficiency was observed for second harmonic laser irradiation (λ_L = 0.527 μm) at an intensity of 8×10¹² W/cm²     

激光等离子体软X射线辐射能谱时间分辨测量研究

利用(国内最近研制成功的)带聚酰亚胺膜底衬的金透射光栅与软X射线条纹相机相配合,(在LF11~#激光装置上)使用波长为0.53μm的激光打靶,测量了平面Au靶软X射线时间分辨能谱。测量结果观察到了金等离子体的O带辐射强度随时间增加的现象。文章计算了光栅的衍射效率,并讨论了影响测量谱的几个关键因素。     

Measurements and interpretation of the absorption of 0.35 μm laser radiation on planar targets

We report on experimental plasma absorption of 0.35 μm radiation incident on plane targets. Absorption fractions between 50 and 98% were found for UV pulses of 90 and 450 ps duration on planar CH, nickel, and gold targets for intensities between 10¹³ and 3 × 10¹⁵ W/cm². The results are in agreement with computer calculations using inverse bremsstrahlung absorption and a thermal electron heat flux limiter between 0.03 and 0.06     

表面绝缘混合平面丝阵Z箍缩激光阴影图像诊断

基于脉冲半高全宽约为9 ns、波长为532 nm的Nd:YAG激光器,采用条纹相机和商用数码相机两种记录设备,建立了时间分辨和时间积分两种模式的激光阴影图像诊断系统,在"强光一号"装置上对表面绝缘混合平面丝阵Z箍缩等离子体开展了实验研究.实验结果表明:在融蚀过程中表面绝缘金属丝冕等离子体发展较普通金属丝慢,在t=44ns到t=56ns之间,其平均膨胀速度分别为1.1×104m·s-1和1.7×104m·s-1;在等离子体滞止前10 ns的快速聚爆过程中,表面绝缘金属丝和普通金属丝两侧的平均聚爆速度分别为5.5×105m·s-1和9.3×105m·s-1,表面绝缘一侧等离子体滞止时间小于普通金属丝一侧,分别为5.9 ns和9.5 ns;等离子体碰撞分界线偏向于表面绝缘一侧,滞止时形成的磁流体不稳定性结构类似.     

类锂硅离子X射线激光谱线宽度和电子密度的空间分布

通过分析类锂硅离子X射线激光谱线宽度的空间分布特性,表明斯塔克展宽是主要的展宽机制;由此得到增益介质电子密度的空间分布显示增益区电子密度约在10¹⁹/cm³左右,对应最大增益处的线宽为0.21?,电子密度为2.9×10¹⁹/cm³。 关键词：     

Optical measurements of plasma dynamics in carbon fiber Z-pinches

A series of experiments has been carried out on the Mega Ampere Generator for Plasma Implosion Experiments (MAGPIE) generator in order to study the dynamics of carbon fiber Z-pinches. The generator was operated at 1.4 MV, with a peak current of 1 MA, and a rise time of 150 ns. In some shots, a current prepulse of about 30 kA was provided to study its influence on the dynamics of the fiber pinch. Carbon fibers of 7, 33, and 300 μm diameter were used during these experiments. The diagnostics employed were a self-referencing interferometer, a two-frame Schlieren system, an optical streak camera, and a four-frame X-ray framing camera. A novel feature of these measurements is the employment of an optical streak camera with a set of four slits arranged along the fiber axis and displaced in the radial direction. This permitted the study of the temporal evolution (axial and radial) of the plasma regions emitting in the visible part of the spectra. Correlation between these regions of the plasma and the location of X-ray hot spots is discussed. In carbon fibers of 33 pm diameter, the radial expansion velocity measured from Schlieren images was 3.6×10⁶ cm/s and 5.5×10⁶ cm/s for shots with and without prepulse, respectively. The dominant axial wavelengths of instabilities in the coronal plasma were between 0.05 and 0.2 cm, which correspond to ka values between 10 and 20, where k is the wavenumber of the instability and a is its amplitude. The dynamics of carbon fibers of different diameters are compared     

Comparison of nanosecond laser ablation at 1064 and 308 nm wavelength

To study the solid Cu ablation in vacuum, two different laser sources operating at 1064 and 308 nm wavelength are employed at similar values of laser fluences. The infrared laser is a Q-switched Nd:Yag having 9 ns pulse width (INFN-LNS, Catania), while the ultraviolet one is a XeCl excimer having 20 ns pulse width (INFN-LEA, Lecce). Both experiments produced a narrow angular distribution of the ejected material along the normal to the target surface. The ablation showed a threshold laser power density, of about 7 and 3 J/cm² at 1064 and 308 nm, respectively, below which the ablation effect was negligible. The laser interaction produces a plasma at the target surface, which expands very fast in the vacuum chamber. Time-of-flight (TOF) measurements of the ion emission indicated an average ion velocity of the order of 4.7×10⁴ and 2.3×10⁴ m/s for the infrared and ultraviolet radiation, respectively. We also estimated approximately the corresponding temperature of the plasma from which ions originated, i.e. about 10⁶ and 10⁵ K for IR and UV wavelength, respectively. A discussion of the analysis of the ablation mechanism is presented. At the used laser power densities the produced Cu ions showed ionisation states between 1+ and 5+ in both cases.     

Electron density and temperature contour plots from alaser-produced plasma using collective ultraviolet Thomson scattering

Temporally integrated ultraviolet collective Thomson scattering measurements were performed with frequency-quadrupled Nd:YAG laser radiation on an underdense long-scalelength aluminum plasma (n_c ~10²¹ cm^-3, Z≈7, T_e≈T_i ⩾50 eV, L⩾100 μm). The plasma was preformed by an Nd:YAG fundamental beam (1.06 μm) with focusable intensities of 10 ¹¹ W/cm². Color images of two-dimensional (2-D) spatially resolved (30 μm) electron density and electron temperature were obtained. These are the shortest wavelength Thomson scattering measurements on a plasma to date     

用于原子干涉仪实验的锂原子的塞曼减速与磁光囚禁

为了制备适于原子干涉仪实验的低温锂原子样品,开展了锂原子的塞曼减速及与磁光阱囚禁相关的实验研究.设计并实现了一种结构紧凑的腔体内冷式多级线圈叠加的塞曼减速器,将速度小于600 m/s的7Li原子减速到60 m/s,磁光阱装载速率为5×108/s,囚禁原子数目1×109个,原子团的最低温度约为220±30μK.研究了光学黏胶中7Li原子的寿命与囚禁光频率失谐量的关系.这些结果为进一步开展7Li原子亚多普勒冷却、光势阱蒸发冷却以及原子干涉仪实验奠定了基础.