Mechanisms and factors influencing the removal of microcystin-LR by ultrafiltration membranes

In this study, we investigate the application of ultrafiltration (UF) for the removal of the cyanotoxin, microcystin-LR, and determine the dominant removal mechanisms. System variables examined included membrane characteristics, feed concentration, water recovery and operating pressure. While adsorption dominated rejection for most UF membranes, at least at early filtration times, both size exclusion and adsorption were important in removing microcystin-LR by the tight thin-film (TF) membranes. Adsorption was primarily attributed to hydrophobic interactions, although hydrogen bonding and physical surface properties such as surface roughness, thickness, and porosity may also play a role. Polysulfone membranes, the most hydrophobic membrane examined, significantly adsorbed microcystin-LR (91%), whereas the more hydrophilic cellulose acetate membranes adsorbed little or no microcystin-LR. The initial feed concentration had a significant influence on the adsorption capacity of TF membranes for microcystin-LR, which could be described based on a linear adsorption isotherm. An increase in water recovery and/or operating pressure led to an increase in the adsorption of microcystin-LR, probably due to increased convective transport. On the other hand, microcystin-LR rejection through size exclusion was reduced for higher water recovery and/or applied pressure.     

A rapid approach for assessment of arsenic exposure by elemental analysis of single strand of hair using laser ablation-inductively coupled plasma-mass spectrometry

Application of laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) as a method for identification of arsenic in a single hair strand was investigated. Using a single point ablation method detectability of ⁷⁵As and other two elements (²⁰⁸Pb and ⁶⁴Zn) were evaluated. Arsenic (⁷⁵As) signal is improved with enhanced laser ablation conditions. For the arsenic determination in hair single spots or single linear scans with enhanced laser ablation conditions described in the paper are satisfactory although  800 μm linear scans may be preferable. Arsenic levels in a single strand of hair from individuals who were chronically exposed to arsenic contaminated drinking water from a village in the Atacama Desert in northern Chile were determined by LA-ICP-MS. These results were satisfactorily correlated with total As concentration previously measured by hydride generation (HG)-ICP-MS. The sample throughput is high and it takes  3 min per each hair sample including mounting, focusing and analysis. LA-ICP-MS method can be used for the rapid identification and screening of toxic and nutritionally important elements in hair.     

Photodegradation of poly(neopentyl isophthalate) part I: Laboratory and outdoor conditions

In this paper the mechanisms of photodegradation of poly(neopentyl isophthalate) (PNI) in laboratory (Suntest XXL+, λ > 300 nm) and outdoor conditions are compared. Changes in the chemical composition were studied with ATR-FTIR, SEC and MALDI-ToF MS. Furthermore, the results were compared with data presented in our previous paper on PNI coatings that were aged in the UVACUBE (λ > 254 nm). Two main aspects of photodegradation of PNI are addressed in the present paper: the influence of different wavelengths and the comparison of laboratory and outdoor exposure regarding the mechanism of degradation. Under short (λ > 254 nm) and long (λ > 300 nm) wavelength irradiation similar products of degradation are formed. However, the presence of short wavelength radiation dramatically accelerates the overall rate of photodegradation of PNI. UV light absorption calculations confirm this experimentally found acceleration. Exposure of PNI in laboratory and outdoor conditions, both with wavelengths λ > 300 nm resulted in similar degradation products in the initial stage of ageing.     

Dual electrochemical microsensor for simultaneous measurements of nitric oxide and oxygen: Fabrication and characterization

A planar-type amperometric dual microsensor was developed for the simultaneous measurement of the nitric oxide (NO) and oxygen (O₂) concentrations. The sensor (overall diameter = 500 μm) consisted of a dual working electrode (WE) containing two platinized platinum microdisks (25 μm diameter, WE1, WE2, distance between two disks > 330 μm) and a Ag/AgCl wire reference electrode covered with an expanded poly(tetrafluoroethylene) gas-permeable membrane. The differentiation and concurrent measurements of NO and O₂ were obtained successfully using two sensing WEs with different applied potentials (+0.75 V for WE1 and −0.4 V for WE2). Cross-talk between WE1 and WE2 was eliminated with an optimized internal solution composition. Linear dynamic range, selectivity, sensitivity, detection limit (<5 nM for NO; <500 nM for O₂), and stability (>50 h) were evaluated.     

Isoconversional kinetics of degradation of polyvinylpyrrolidone used as a matrix for ammonium nitrate stabilization

Thermogravimetric analyzer (TGA) has been applied to measure the kinetics of the thermal degradation of virgin polyvinylpyrrolidone (PVP) and a phase stabilized PVP–ammonium nitrate (AN) material. The PVP–AN samples have been prepared by using 20 wt.% of AN and PVP of three different molecular weights. Virgin PVP undergoes a major mass loss in the region 380–550 °C leaving a small amount of nonvolatile residue. The application of an advanced isoconversional method to the respective degradation process demonstrates that its effective activation energy increases from 70 kJ mol⁻¹ to a plateau value at 250–300 kJ mol⁻¹, which is independent of the molecular weight. The PVP–AN materials lose spontaneously 20% of their mass on heating above the glass transition temperature of the PVP matrix (160–180 °C). After the escape of AN, the remaining PVP matrix degrades in the same temperature region as virgin PVP, however, the effective activation energy of this degradation is 150–200 kJ mol⁻¹.     

Electrochemical properties of polyaniline in p-toluene sulfonic acid solution

Polyaniline was deposited potentiodynamically on a stainless steel substrate in the presence of an inorganic acids (sulfuric acid). The electrochemical characterization of the electrode was carried out by means of cyclic voltammetry and electrochemical impedance spectroscopy in the organic acids (p-toluene sulfonic acid) solution. The results show that polyaniline has a high specific capacitance of 431.8 F g⁻¹ at 1 mV s⁻¹, high coulombic efficiency of 95.6% at 20 mV s⁻¹, and exhibits a high reversibility. This indicates the promising feasibility of the polyaniline used as an electrochemical capacitor material in the electrolyte of p-toluene sulfonic acid solution especially at high charge–discharge process.     

Expanding mesoporosity of triblock-copolymer-templated silica under weak synthesis acidity

With initial aging at low temperature for enough time, silicas with large mesoporosity were synthesized using triblock copolymer as template agent under weak acidities. SBA-15 with periodic mesostructure and short mesochannels could be synthesized at pH 2.5–3.0 within weak acidity range, and the surface areas, pore diameters and pore volumes reached up to ca. 1000 m²/g, 8.8 nm and 2.0 cm³/g, respectively, which were significantly higher than those of the conventional SBA-15 synthesized under strong acidities. Mesoporous silica with wormhole structure and abundant textural porosity was formed at pH  3.5. The increased hydrophobic volume of the copolymer micelles at elevated pH values was responsible for the enlargement of mesoporosity in the products. The materials synthesized under weak acidities showed lower hexagonal ordering in comparison to the general SBA-15 synthesized under strong acidities because the decreased hydronium ion concentration induced relatively weaker assembly forces during the synthesis. Nonetheless, the short mesochannels and large pore diameter in the products might be beneficial to some applications in which fast diffusion of molecules is required.     

Resistance-in-series analysis in cross-flow ultrafiltration of fermentation broths of Bacillus subtilis culture

Quantitative analysis of various resistances that lead to flux decline during cross-flow ultrafiltration (UF) of the fermentation broth of Bacillus subtilis ATCC (American Type Culture Collection) 21332 culture was studied. Polyethersulfone membrane with a molecular weight cut-off (MWCO) of 100 kDa was used. Prior to cross-flow UF, the broth was treated by acid precipitation (pH 4.0) and centrifugation, and the precipitate was re-dissolved in NaOH solution. Experiments were performed at a feed pH of 7.0, a feed surfactin concentration of 1.48 g L⁻¹, and a cross-flow velocity of 0.32 m s⁻¹ but at different transmembrane pressures (ΔP, 20–100 kPa). The resistance-in-series model was used to analyze the flux behavior, which involves the resistances of membrane itself and cake as well as those due to adsorption and solute concentration polarization. It was shown that the resistance due to solute concentration polarization and of membrane dominated under the conditions examined. The resistances due to cake formation and solute adsorption were comparable, and their sum contributed below 20% of the overall resistance.     

Molecular fine structure and transition dipole moment of NO2 using an external cavity quantum cascade laser

Rotational vibrational fine structure and transition dipole moment of NO₂ is measured using Doppler free saturation spectroscopy with an external grating cavity quantum cascade laser (QCL). The QCL wavelength is calibrated using a 310 cm long internally coupled Fabry–Perot interferometer. We obtain a frequency splitting of 139.68 ± 0.06 MHz (0.0047 cm⁻¹) between the spin doublets (17) of 000 → 001 transition of NO₂. The resolution of the QCL based saturation spectrometer is limited by the QCL linewidth of 3.99 MHz ( 0.00013 cm⁻¹) deduced from the half width of the Lamb dips. The Lamb dip spectroscopy is utilized to obtain a vibrational dipole moment of 0.37 Debye for the (17) transitions.     

Fabrication and superhydrophobicity of fluorinated titanium dioxide nanocoatings

This study demonstrates the fabrication of a stable superhydrophobic surface with low contact angle hysteresis (CAH) using an arrangement of nanoscale TiO₂ spheres. The control of precursor quantity is selected as the key factor in determining surface roughness that significantly intensifies water contact angle (CA) of TiO₂ films. After surface fluorination treatment, the anatase-type crystalline surfaces exhibit good water repellency (CA 166.1°), low CAH (6°), and superhydrophobic stability (>60 min). Enhanced water repellency is attributed to the fact that the higher density of TiO₂ spheres results in more tortuous three-phase contact line, leading to the self-cleaning effect. Such a unique textured surface imparts many promising potentials for engineering and the development of optics devices with robust superhydrophobic materials.     

Enhanced tungstate electrochromism via formation of transparent conductive networks

Indium tin oxide (ITO) nanopowder was added to a polymer film containing WO₃ · H₂O particles to enhance electron conductivity and complimentary Li ion kinetics in an electrochromic device. Film conductivity increased dramatically with ITO content, suggesting the formation of conductive ITO networks in the film. The improved electron conductivity leads to a substantial increase of the effective Li⁺ ion diffusion coefficient in the composite film, from 10⁻¹¹ to 10⁻⁹ cm²/s. Electrochromic contrast studies revealed that the presence of the ITO networks leads to enhanced blue/green color contrast.     

Pervaporation dehydration of ethylene glycol with chitosan–poly(vinyl alcohol) blend membranes: Effect of CS–PVA blending ratios

Chitosan–poly(vinyl alcohol), CS–PVA, blended membranes were prepared by solution casting of varying proportions of CS and PVA. The blend membranes were then crosslinked interfacially with trimesoyl chloride (TMC)/hexane. The physiochemical properties of the blend membranes were determined using Attenuated Total Reflection-Fourier Transform Infrared Spectroscopy (ATR-FTIR), X-ray diffraction (XRD), differential scanning calorimetry (DSC), tensile test and contact angle measurements. Results from ATR-FTIR show that TMC has crosslinked the blend membranes successfully, and results of XRD and DSC show a corresponding decrease in crystallinity and increase in melting point, respectively. The crosslinked CS–PVA blend membranes also show improved mechanical strength but lower flexibility in tensile testing as compared to uncrosslinked membranes. Contact angle results show that crosslinking has decreased the surface hydrophilicity of the blend membranes. The blend membrane properties, including contact angle, melting point and tensile strength, change with a variation in the blending ratio. They appear to reach a maximum when the CS content is at 75 wt%. In general, the crosslinked blend membranes show excellent stability during the pervaporation (PV) dehydration of ethylene glycol–water mixtures (10–90 wt% EG) at different temperatures (25–70 °C). At 70 °C, for 90 wt% EG in the feed mixture, the crosslinked blend membrane with 75 wt% CS shows the highest total flux of 0.46 kg/(m² h) and best selectivity of 986. The blending ratio of 75 wt% CS is recommended as the optimized ratio in the preparation of CS–PVA blend membranes for pervaporation dehydration of ethylene glycol.     

Ultrafast dynamics of heat flow across molecules

An ultrafast flash thermal conductance apparatus is used to study heat flow through aliphatic and aromatic molecules arranged in self-assembled monolayers (SAMs). The apparatus consists of a thin metal film which can be flash-heated by many hundreds of degrees in 1 ps using a femtosecond pulse. Heat flow from the metal surface into the SAM molecules is detected using vibrational sum-frequency generation (SFG) spectroscopy. The SAMs studied were alkanethiolates (AT) ranging from C6 to C24, benzenethiolate (BT) and benzylmercaptide (BMT). SFG in the CH-stretch region selectively probes transitions of the terminal methyl groups of AT and the CH moiety at the 4-position of the phenyl ring of BT and BMT (opposite the thiolate-surface bond). The SFG signal is sensitive to temperature-jump induced thermal disorder of the SAM and also to vibrational frequency shifts induced by the changing intramolecular vibrational populations. The SFG probe functions as a thermometer, and this thermometer is 1.5 Å thick with a response time of 1 ps. In the AT chains, a study of the length dependence is used to determine the rate heat flows across the metal–SAM interface and the rate of heat flow through the AT chains. The interface thermal conductance is 220 GW m⁻² s⁻¹. The AT molecular conductance is 50 pW K⁻¹ or 0.3 eV s⁻¹ K⁻¹. Heat flow through the AT chains is ballistic with a velocity of 1 km/s. Heat flow into BMT is slower than in BT because BMT has one additional methylene linker group. The BT and BMT structures evidence a thermally-initiated surface rearrangement occurring in a few tens of picoseconds. These SAMs are strained and the phenyl rings cannot adopt the most stable staggered herringbone structure. After the T-jump, the SAM molecules have enough freedom to relax into more favorable configurations.     

Preparation and characterization of mesoporous N-doped and sulfuric acid treated anatase TiO2 catalysts and their photocatalytic activity under UV and Vis illumination

Nitrogen-doped TiO₂ catalysts were prepared by a precipitation method. The samples were calcined at 400 °C for 4 h in air. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), low temperature N₂-adsorption was used for structural characterization and UV-diffuse reflectance (UV-DR) was applied to investigate the optical properties of the as-prepared samples. It was found that microporous N-doped catalysts have solely anatase crystalline structure. Acidic treatment of the calcined samples was performed using sulfuric acid agitation. The crystalline structure remained unchanged due to surface treatment, while the porosity and the surface areas were decreased dramatically. Optical characterization of the doped catalysts showed that they could be excited by visible light photons in the 400–500 nm wavelength range (λ_g,1=390 nm, λ_g,2=510 nm). It was also established that surface treatment enhances the Vis-light absorption of the N-TiO₂ powders. Finally the catalysts were tested in the photocatalytic degradation of phenol in aqueous suspensions. Two different light sources were used; one of them was a UV-rich high pressure Hg-lamp, while the other was a tubular visible light source. We found that using visible light illumination N-doped, acid treated TiO₂ samples were more catalytically active than non-doped TiO₂ catalysts.     

Effects of adsorption-induced microstructural changes on separation of xylene isomers through MFI-type zeolite membranes

Various factors were found to affect the performance of MFI-type zeolite membranes in separating xylene isomers (p-xylene, PX; o-xylene, OX) by pervaporation. In this work the effect of membrane microstructure, membrane quality, and pervaporation operating conditions were investigated using three membrane microstructures: random, c-oriented, and h,0,h-oriented. Operation under pervaporation conditions means that high loadings of PX will be present in the framework; therefore, the role of PX–framework and PX–OX interactions needs to be taken into consideration. Single component experiments demonstrated that the order of experimentation with OX and PX will affect the ideal selectivity. Multi-component studies showed that membrane performance is highly dependent on the relative concentration of the isomers in the feed; the higher the PX concentration the lower the selectivity observed. However, although high selectivity (18) was observed at low PX concentrations in the feed, it was not stable over time. Similar trends were observed for all membrane microstructures but differences in the selectivity values occurred. The structural deformation caused by high loadings of PX into the silicalite crystal affects each microstructure differently, ultimately leading to differences in performance.     

Magnetic field effect on chemical compositions of spherical Fe/Co fine particles synthesized from a gaseous mixture of iron pentacarbonyl and cobalt tricarbonyl nitrosyl

Under UV light irradiation on a gaseous mixture of Fe(CO)₅ and Co(CO)₃NO, both the crystalline deposits with sizes of 5 and 18 μm and the spherical particles with a mean diameter of 0.3 μm were produced. From FT-IR spectra and SEM–EDS analysis, it was suggested that the chemical structure of the crystalline deposits was the one of Fe₂(CO)₉ being modified by involving Fe(CO)Co bond. By decreasing a partial pressure of Fe(CO)₅ to 0.5 Torr in the gaseous mixture, only the spherical aerosol particles could be produced. Chemical composition of the particles was rich in Co species. From the disappearance of bridging CO band in the FT-IR spectra of the particles and the appearance of CO bands coordinated to a metal atom, Fe atom in Fe(CO)₄ was suggested to be coordinated by the O atom in bridging CO bond in Co(CO)Co structure and/or in α-diketone structure which was formed from two CO groups in dicobalt species. Chemical compositions of the crystalline deposits and the spherical particles were influenced differently by the application of a magnetic field. Atomic ratio of Fe to Co atom decreased in the crystalline deposits whereas it increased in the spherical particles with increasing magnetic field up to 5 T. Linearly aggregated particles (i.e., particle wires) as long as 30 μm were produced on the front side of a glass plate placed at the bottom of the irradiation cell.     

Barrier properties of polymer/alumina nanocomposite membranes fabricated by atomic layer deposition

Novel polymer/ceramic nanocomposite membranes were fabricated, characterized and tested for their barrier performance. Atomic layer deposition (ALD) was used to deposit alumina films on primary, micron-sized (16 and 60 μm) high-density polyethylene (HDPE) particles at a rate of 0.5 nm/cycle at 77 °C. Well-dispersed polymer/ceramic nanocomposites were obtained by extruding alumina coated HDPE particles. The dispersion of alumina flakes can be controlled by varying the number of ALD coating cycles and substrate polymer particle size. The diffusion coefficient of fabricated nanocomposite membranes can be reduced to half with the inclusion of 7.29 vol.% alumina flakes. However, a corresponding increase in permeability was also observed due to the voids formed at or near the interface of the polymer and alumina flakes during the extrusion process, as evidenced by electron microscopy. The low surface wettability of the alumina outerlayers was believed to be one of the main reasons of void formation. Particle surface wettability was improved using 3-aminopropyltriethoxysilane (APS) to coat the particle ALD surface modified polymer particles prior to extrusion. The diffusion coefficient and permeability of the membrane using surfactant-modified particles decreased by 20%, relative to the non-modified case.     

An octane-fueled low temperature solid oxide fuel cell with Ru-free anodes

A Ru-free anode was developed for the direct utilization of iso-octane in low temperature solid oxide fuel cells (SOFCs). The anode was consisted of a Ni framework and a nano-sized oxygen–ion conductor, samaria-doped ceria (SDC), which was coated onto the inner surface of the framework via an ion impregnation process. Compared with the cells based on conventional Ni–SDC anodes, single cells with the SDC-coated Ni anodes exhibited improved stability and enhanced electrochemical activity. Peak power density of 400 mW cm⁻² was achieved at 600 °C, and power generation was relatively stable over 260 h when iso-octane–air mixture was directly used as the fuel. The performance is comparable with those obtained using ceria-Ru as an internal reforming catalyst.     

Photophysics of Genistein isoflavone: Solvent and concentration effects studied by UV–visible spectroscopy and theoretical simulation

Genistein isoflavone is shown to exist in two different conformations which are the 90° completely twisted geometry and the 50° less twisted one. Specific interactions with the solvent cage as well as self-association processes seem shifting the isoflavone from the perpendicular conformation towards the less twisted one. The theoretical simulation, using analytical atom–atom pair potential, predicts a self-dimer in a slipped non-sandwich, face to river, perpendicular structure. From the UV–visible photophysics investigations it is revealed that monomeric species cannot exist alone even at very low solute concentration (10⁻⁶ M), the self-association process occurs already in this concentration range.     

Interaction and photodynamic activity of cationic porphyrin derivatives bearing different patterns of charge distribution with GMP and DNA

The interaction of amphiphilic cationic porphyrins, containing different patterns of meso-substitution by 4-(3-N,N,N-trimethylammoniumpropoxy)phenyl (A) and 4-(trifluoromethyl)phenyl (B) groups, with guanosine 5′-monophosphate (GMP) and calf thymus DNA have been studied by optical methods in phosphate buffer solution. The properties of these synthetic porphyrins were compared with those of representative standard of anionic 5,10,15,20-tetra(4-sulphonatophenyl)porphyrin (TPPS₄⁴⁻) and cationic 5,10,15,20-tetra(4-N,N,N-trimethylammonium phenyl)porphyrin (TMAP⁴⁺). Stable complexes with GMP were found for cationic porphyrins, except for monocationic AB₃⁺. The binding constant (K_GMP  10⁴ M⁻¹) follows the order: A₃B³⁺  ABAB²⁺ > A₄⁴⁺  TMAP⁴⁺. Also, interaction with DNA was observed for all evaluated cationic porphyrins. For these related cationic porphyrins, the binding constant (K_DNA  10⁵ M⁻¹) increases with the number of cationic charges. On the other hand, the photodynamic activity of porphyrins was analyzed in solution of GMP and DNA. Monocationic AB₃⁺ is a less effective sensitizer to oxidize GMP in comparison with the other cationic porphyrins, in agreement with the lack of detected interaction with this nucleotide. The electrophoretic analysis of DNA indicates that photocleavage takes place when the samples are exposed to photoexcited tricationic and tetracationic porphyrins. In the presence of sodium azide the DNA decomposition was diminished. Also, reduction in the DNA photocleavage was observed under anoxic condition, indicating that oxygen is essential for DNA photocleavage sensitized by these cationic porphyrins. In addition, an increase in DNA degradation was not observed in deuteriated water. Therefore, an important contribution of type I photoreaction processes could be occurring in the DNA photodamage sensitized by these cationic porphyrins. These results provide a better understanding of the characteristics needed for sensitizers to produce efficient DNA photocleavage.