Study of Analytical Methods for Iron Determination in Complex Organic Liquids by Atomic Absorption Spectrometry

Abstract

In the determination of iron in complex organic liquids by atomic absorption spectrometry (A. A. S.), methods of sample preparation, such as dilution with an organic solvent and sample pretreatment to destroy organic material, are investigated. Moreover, methods of analysis using calibration curve and standard additions are presented. The possible cause of error associated with iron determination in organic samples by flame (F-A. A. S.) and graphite furnace (GF-A. A. S.) atomic absorption spectrometry are discussed.

From all of these studies, the use of graphite furnace atomic absorption spectrometry after sample dilution with methyl isobutyl ketone, and the use of the method of standard additions are advised for iron determination.     

On-Line Preconcentration and Simultaneous Determination of Cu and Mn in Water Samples Using a Minicolumn Packed with Sisal Fiber by MIP OES

An on-line preconcentration system for the simultaneous determination of Copper (Cu) and manganese (Mn) in water samples was developed and coupled to a microwave-induced plasma optical emission spectrometer (MIP OES). The flow injection system was designed with a minicolumn packed with sisal fiber (Agave sisalana). A multivariate experimental design was performed to evaluate the influence of pH, preconcentration time, and eluent concentration. Optimal conditions for sample preparation were pH 5.5, preconcentration time was 90 s, and HCl 0.5 mol L⁻¹ was the eluent. The main figures of merit were detection limits 3.7 and 9.0 µg L⁻¹ for Cu and Mn, respectively. Precision was expressed as a relative standard deviation better than 10%. Accuracy was evaluated via spiked recovery assays with recoveries between 75–125%. The enrichment factor was 30 for both analytes. These results were adequate for water samples analysis for monitoring purposes. The preconcentration system was coupled and synchronized with the MIP OES nebulizer to allow simultaneous determination of Cu and Mn as a novel sample introduction strategy. The sampling rate was 20 samples/h. Sisal fiber resulted an economical biosorbent for trace element preconcentration without extra derivatization steps and with an awfully time of use without replacement complying with the principles of green analytical methods.     

Determination of Mercury in Urine and Seawater by Flow Injection Vapor Generation Isotope Dilution Inductively Coupled Plasma Mass Spectrometry

A simple and inexpensive laboratory-built vapor generator was used with inductively coupled plasma mass spectrometry (ICP-MS) for the determination of mercury in urine and seawater samples. The applications of vapor generation ICP-MS alleviated the non-spectroscopic interferences and the sensitivity problem of mercury determination encountered when the conventional pneumatic nebulizer was used for sample introduction. The concentration of mercury was determined by isotope dilution method. The isotope ratio of mercury was calculated from the peak areas of each injection peak. The repeatability of the peak areas and isotope ratio determinations of seven consecutive injections of 1 ng mL^?1 Hg solution were 2.3% and 2.2%, respectively. This method has a detection limit of 0.07 ng mL^?1 for mercury. This method was applied to determine mercury in a CASS-3 nearshore seawater reference sample, NASS-4 open ocean seawater reference sample, NIST SRM 2670 freeze-dried urine reference sample and several urine and seawater samples collected from National Sun Yat-Sen University. The results for the reference samples agreed satisfactorily with the reference values. Results for other samples analyzed by the isotope dilution method and the method of standard additions agreed satisfactorily. Precision was better than 10% for most of the determinations.     

A mathematical model based on the limit dilution method to obtain linear calibration curves which eliminate the matrix effect in quantitative analysis by X-ray fluorescence

We propose a mathematical model from an analytical application viewpoint inspired in the limit dilution method. The theoretical development of the model and its results are given. The model shows that there is a linear relation between the inverse of fluorescence intensity and the inverse of the dilution factor; each analytic system (sample, diluent and analyte) is characterised by a general linear function which is easily obtained. The analytical applications arising from this linearity are of great importance in X-ray fluorescence analysis. The following immediate applications are proposed: direct procurement of the total correction factor Y/H, rapid calculation of the fluorescence intensity of the analyte in a sample (I_i^s) and direct calculation of the corrected fluorescence intensity (I_i^sF). The suggested model makes it possible to deduce a linear function between the fluorescence intensity of the analyte and the analyte concentration in successive dilutions of a standard; this straight line behaves as a calibration curve with direct application in X-ray fluorescence analysis. The proposed model may be applied to complex samples of geological origin, with elimination of the matrix effect. The results obtained in the determination of Ca, K, Fe and Ti in a standard soil show complete agreement with the certified reference values with a relative error about 0.5%, even using a standard shale with very different chemical composition as reference sample.     

Determination of ultra-trace amounts of Fe in AgNO<Subscript>3</Subscript> solutions by means of isotope dilution analysis applying an inductively coupled plasma mass spectrometer equipped with a dynamic reaction cell

The development of an ICP-MS method for the determination of ultra-trace amounts of Fe in AgNO₃ solutions using isotope dilution for calibration is described. AgNO₃ solutions are used as raw materials in the production of traditional photographic materials, and it is known that contamination with metal traces can influence the quality of the films thus produced. After adding an appropriate amount of an ⁵⁴Fe-enriched spike and permitting isotopic equilibration to take place, Ag was selectively removed from the solutions by precipitation as AgBr. Although to some extent, co-precipitation of Fe is possible under the given circumstances, an incomplete recovery of the analyte element did not affect the accuracy of the results, owing to the use of isotope dilution for calibration. NH₃ was used as a reaction gas in a quadrupole-based ICP-MS instrument, equipped with a dynamic reaction cell (DRC), providing interference-free measurement of the ⁵⁴Fe/⁵⁶Fe ratio. The limit of detection (LOD) obtained using this procedure was approximately 0.01 µg g^-1. This is an excellent value in comparison with the detection limit obtained with the more traditional approach: sample dilution and external calibration with a Fe standard solution (LOD ~1 µg g^-1). To validate the method, recovery experiments were carried out. In all instances, a quantitative recovery was established. Finally, the method was applied to the analysis of AgNO₃ solutions. A large variation in Fe concentration was observed. Depending on the Fe content in the samples, relative standard deviations typically ranged between 1 and 14%.     

X-ray fluorescence determination of total sulfur in fly ash

Standard addition, double dilution and standard calibration were used for x-ray fluorescence (XRF) determinations of sulfur in fly ashes. Samples were analysed as pellets prepared by mixing with acrylate copolymer or with microcrystalline cellulose (in the case of the double dilution method). Lithium sulfate was used for the standard addition method and also as standard with known sulfur content for the double dilution method. Fly ashes analysed by optical emission spectrometry with an inductively coupled plasma (ICP-OES) were used as standards for the standard calibration XRF method. Sulfur was determined in the range of ca. 10^–1–10⁰ % S. For the fly ashes from the North-Bohemian brown coals, the differences between the XRF determinations and the ICP-OES determinations ranged from ca. 1.4 to 10% rel. and precision (repeatability) was better than 10% (RSD). The standard calibration method is suitable for routine analyses of real samples of similar nature. The methods of standard addition and double dilution are rather laborious in sample preparation compared with the standard calibration. Received: 27 October 1998 / Revised: 5 March 1999 / Accepted: 11 March 1999     

Determination of selenium in small volumes of blood plasma and serum by electrothermal atomic absorption spectrometry

A graphite-furnace atomic absorption spectrometric method is described for the determination of selenium in blood plasma and serum. Samples are diluted (1 + 9) with a solution containing nickel and nitric acid and measured by a standard additions method. Repeatability for a serum sample containing 87 μg Se l^-1 was 4.4%. The mean recovery of selenium(IV) from a human protein solution was 97.5%. The method was further tested in an interlaboratory comparison study. The standard additions procedure requires a sample volume of 200 μl and a total time of about 7.5 min. A secondary calibration graph can be used, however, resulting in increased throughput up to 13 samples per hour, and a decrease in the sample volume needed to 100 μl.     

A new continuous calibration method for inductively coupled plasma spectrometry

A new calibration method was developed and applied to inductively coupled plasma atomic emission spectrometry. External calibration was performed as follows. A container was filled with a given volume of deionized (V _p) water. Then a concentrated standard was introduced at a controlled rate (Q _e) into the tank by means of a peristaltic pump. The resulting solution was stirred throughout the experiment. Simultaneously, the solution inside the tank was pumped from the vessel to the plasma at a given rate (Q _s). The signal was continuously recorded. The variation of the concentration of the solution leaving the tank with time was determined by applying a basic equation of stirred tanks. The representation of the emission intensity versus the time and the further conversion of the time scale into a concentration scale gave rise to the calibration line. The best results in terms of linearity were achieved for V _p=15 cm³, Q _e=0.6–0.75 ml min⁻¹ and Q _s=1–1.2 ml min⁻¹. Graphs with more than 40 standards were obtained within about 10 min. The results found were not statistically different from those afforded by the conventional calibration method. In addition, the new method was faster and supplied better linearity and precision than the conventional one. Another advantage of the stirred tank was that procedures such as dynamic calibration and standard additions could be easily and quickly applied, thus shortening the analysis time. A complete analysis following these procedures based on the measurement of 30 standards took about 5 min. Several synthetic as well as certified samples (i.e., bovine liver, mussel tissue and powdered milk) were analyzed with the stirred tank by applying four different calibration methodologies (i.e., external calibration, internal calibration, standard additions and a combination of internal standardization and standard additions), with the combination of internal standardization and standard additions being the method that provided the best results. The element concentrations obtained were not significantly different from the actual or certified values.     

Determination of cadmium,mercury and lead in seawater by electrothermal vaporization isotope dilution inductively coupled plasma mass spectrometry

Electrothermal vaporization isotope dilution inductively coupled plasma mass spectrometry (ETV-ID-ICP-MS) has been applied to the determination of Cd, Hg and Pb in seawater samples. The isotope ratios of the elements studied in each analytical run were calculated from the peak areas of each isotope. Various modifiers were tested for the best signal of these elements. After preliminary studies, 0.15% m/v TAC and 4% v/v HCl were added to the sample solution to work as the modifier. The ETV-ID-ICP-MS method has been applied to the determination of Cd, Hg and Pb in NASS-4 and CASS-3 reference seawater samples and seawater samples collected from Kaohsiung area. The results for reference sample NASS-4 and CASS-3 agreed satisfactorily with the reference values. Results for other samples determined by isotope dilution and method of standard additions agreed satisfactorily. Detection limits were approximately 0.002, 0.005 and 0.001 ng ml⁻¹ for Cd, Hg and Pb in seawater, respectively, with the ETV-ICP-MS method. Precision between sample replicates was better than 20% for most of the determinations.     

Optimization of Sample Preparation of Carrot-Fruit Juice for Determination of Antimony,Arsenic, and Selenium by Hydride Generation-Inductively Coupled Plasma Optical Emission Spectrometry

Sample preparation procedures for the determination of As, Sb, and Se in carrot-fruit juice by hydride generation inductively coupled plasma optical emission spectrometry (HG-ICP OES) were examined. The applicability of a partial decomposition using aqua regia and simple dilution with a 2% (v/v) HNO₃ solution were tested and compared to a traditional treatment based on the wet digestion with a HNO₃/H₂O₂ mixture. The pre-reduction and hydride generation reaction conditions were evaluated. Under the optimal conditions, the hydrides were produced in the reaction of an acidified sample with NaBH₄ after pre-reduction with ascorbic acid [0.5% (m/v)] and KI [0.5% (m/v)] in 3 mol L^?1 HCl for total As and Sb, and boiling with HCl (6 mol L^?1) for total Se. The best results were obtained for the aqua regia procedure, resulting in limits of detection (LODs) between 1.2–2.4 ng g^?1 in the samples and recoveries from 90.9% to 109.1%. The method was successfully applied (without matrix effects) for the determination of As in dense mousse and pulp juice samples and for Sb in pulp juices. Standard solutions, processed in the same way as samples, were used for the calibration. Undecomposed matrix constituents strongly influenced Se; hence this element was determined using the method of standard addition. Concentrations of studied elements in analyzed products were at the trace level, that is, 6–32 ng g^?1, 4–10 ng g^?1, and 4–13 ng g^?1 for Se, As, and Sb, respectively.     

Evaluation of different sample introduction approaches for the determination of boron in unalloyed steels by inductively coupled plasma mass spectrometry

An extended study of different sampling introduction approaches using inductively coupled plasma mass spectrometry (ICP-MS) is presented for the determination of boron in steel samples. The following systems for sample introduction were applied: direct sample solution nebulization by continuous nebulization (CN) using a cross-flow nebulizer and with flow injection (FI), applied to 0.1% (m/v) and 0.5% (m/v) sample solutions, respectively; FI after iron matrix extraction, using acetylacetone–chloroform, and isotopic dilution (ID) analysis as the calibration method; FI with on-line electrolytic matrix separation; and spark ablation (SA) and laser ablation (LA) as solid sampling techniques. External calibration with matrix-matching samples was used with CN, SA, and LA, and only acid solutions (without matrix matching) with FI methods. When FI was directly applied to a sample solution, the detection limit was of 0.15 μg g⁻¹, improving by a factor of 4 that was obtained from the CN measurements. Isotopic dilution analysis, after matrix removal by solvent extraction, made it possible to analyse boron with a detection limit of 0.02 μg g⁻¹ and, with the on-line electrolytic process, the detection limit was of 0.05 μg g⁻¹. The precision for concentrations above 10 times the detection limit was better than 2% for CN, as well as for FI methods. Spark and laser ablation sampling systems, avoiding digestion and sample preparation procedures, provided detection limits at the μg g⁻¹ levels, with RSD values better than 6% in both cases. Certified Reference Materials with B contents in the range 0.5–118 μg g⁻¹ were used for validation, finding a good agreement between certified and calculated values.     

Determination of Mercury and Thallium in Seawater by Electrothermal Vaporization Inductively Coupled Plasma Mass Spectrometry

Electrothermal vaporization inductively coupled plasma mass spectrometry (ETV‐ICP‐MS) has been applied to the determination of Hg and Tl in seawater samples. Various modifiers were tested for the best signal of these elements. After preliminary studies, 0.3% EDTA, 0.1%m/vTAC and 1% v/v HCl were added to the sample solution to work as the modifier. Since the sensitivities of Hg and Tl in various seawater matrices and aqueous standard solutions were quite different, standard addition method and isotope dilution method were used for the determination of Hg and Tl in these seawater samples. This method was applied to the determination of Hg and Tl in NASS‐4 and CASS‐3 reference seawater samples and seawater samples collected from the Kaohsiung area. Results obtained by isotope dilution method and method of standard additions agreed satisfactorily. Detection limits were in the range of 5‐15 and 0.4‐0.5 ng l^?1 for Hg and Tl in seawater, respectively, with the ETV‐ICP‐MS method. The precision between sample replicates was better than 18%) for all the determinations.     

Combining standard addition method and second-order advantage for direct determination of salicylate in undiluted human plasma by spectrofluorimetry

Second-order advantage turns possible a determination in the presence of unknown interferences. This work presented an application of the second-order advantage provided by parallel factor analysis (PARAFAC). The aim was the direct determination of salicylic acid (SA), the main product of aspirin degradation, in undiluted human plasma by spectrofluorimetry. The strategy of this analysis combined the use of PARAFAC, for extraction of the pure analyte signal, with the standard addition method, for a determination in the presence of a strong matrix effect caused by the quenching effect of the proteins present in the plasma. For each sample, four standard additions were performed, in triplicates. A specific PARAFAC model was built for each triplicate of each sample, from three-way arrays formed by 436 emission wavelengths, 7 excitation wavelengths and 5 measurements (sample plus 4 additions). In all the cases, the models were built with three factors and explained more than 99.90% of the total variance. The obtained loadings were related to SA and two background interferences. The scores related to SA were used for a linear regression in the standard addition method. Good results were obtained for determinations in the SA concentration range from 3.0 to 24.0 μg ml⁻¹, providing errors of prediction between 0.7 and 6.3%.     

Determination of Rare earth elements in environmental samples by solid phase extraction ICP OES

A simple sample pre-treatment method for rare earth elements enrichment from environmental water samples prior to optical emission spectrometry determination with inductively coupled plasma (ICP OES) is proposed based on solid phase extraction with octadecyl silica gel modified with 1,2,5,8-tetrahydroxyanthraquinone. Optimal experimental conditions including pH of sample solution, sample volume, type, concentration and volume of eluent were investigated and established. Rare earth elements ions were quantitatively adsorbed from aqueous solution onto octadecyl silica gel modified with Quinalizarin at pH 7.0. The adsorbed ions were eluted with 1.0 mL of 2 M HNO₃ and simultaneously determined by ICP OES. Under obtained optimum conditions the calibration curves were linear with the coefficient of variation better than 0.99. The limit of detection of the method for the studied elements was in the range of 0.0004–0.01 ng/mL. The proposed method has a pre-concentration factor of 320–450 in water samples, which results in high sensitivity detection of trace ions. The developed method gave recoveries better than 80% and RSDs less than 15%.     

Determination of Mn, Fe, Co, Ni, Cu, Zn, Cd and Pb in seawater using high resolution magnetic sector inductively coupled mass spectrometry (HR-ICP-MS)

A novel method, combining isotope dilution with standard additions, was developed for the analysis of eight elements (Mn, Fe, Co, Ni, Cu, Zn, Cd and Pb) in seawater. The method requires just 12 mL of sample and employs an off-line pre-concentration step using the commercially available chelating resin Toyopearl AF-Chelate-650M prior to determination by high resolution inductively coupled plasma magnetic sector mass spectrometry (ICP-MS). Acidified samples were spiked with a multi-element standard of six isotopes (⁵⁷Fe, ⁶²Ni, ⁶⁵Cu, ⁶⁸Zn, ¹¹¹Cd and ²⁰⁷Pb) enriched over natural abundance. In addition, standard additions of a mixed Co and Mn standard were performed on sub-sets of the same sample. All samples were irradiated using a low power (119 mW cm⁻²; 254 nm) UV system, to destroy organic ligands, before pre-concentration and extraction from the seawater matrix. Ammonium acetate was used to raise the pH of the 12 mL sub-samples (off-line) to pH 6.4 ± 0.2 prior to loading onto the chelating resin. The extracted metals were eluted using 1.0 M Q-HNO₃ and determined using ICP-MS. The method was verified through the analysis of certified reference material (NASS-5) and the SAFe inter-comparison samples (S1 and D2), the results of which are in good agreement with the certified and reported consensus values. We also present vertical profiles of the eight metals taken from the Bermuda Atlantic Time Series (BATS) station collected during the GEOTRACES inter-comparison cruise in June 2008.     

Residue analysis of onions and other foodstuffs with a complex matrix using two-dimensional capillary-GC with three selective detectors

Summary A very fast determination of sulphate in ground and drinking water by inductively coupled plasma emission spectrometry (ICP/OES) is described. The 182.037 nm line was selected for the measurement of the total sulphur content, because this line is not disturbed by calcium, one of the main components in natural waters. The limit of determination (0.5 mg/l SO ₄ ^2– ) is low enough for most aquatic samples. With a two point calibration the linear working range is between 0.5 and 100 mg/l SO ₄ ^2– .     

Total sulfur determination in gasoline,kerosene and diesel fuel using inductively coupled plasma optical emission spectrometry after direct sample introduction as detergent emulsions

Herein, we present the development of a procedure for the determination of total sulfur in petroleum-derived products (gasoline, kerosene and diesel fuel) employing inductively coupled plasma optical emission spectrometry (ICP OES). For this procedure, samples were prepared as emulsions that were made using concentrated nitric acid, Triton X-100, sample, and ultra pure water in proportions of 5/10/7/78% (v/v), respectively. Sample volumes were weighed because of the density differences, and oxygen was added to the sheat gas entrance of the ICP OES in order to decrease carbon deposition in the torch and to minimize background effects. A Doehlert design was applied as an experimental matrix to investigate the flow ratios of argon (sheat and plasma gas) and oxygen in relation to the signal-to-background ratio. A comparative study among the slopes of the analytical curves built in aqueous media, surfactant/HNO₃, and by spike addition for several sample emulsions indicates that a unique solution of surfactant in acidic media can be employed to perform the external calibration for analysis of the emulsions. The developed procedure allows for the determination of the total sulfur content in petroleum derivatives with a limit of detection (LOD) and limit of quantification (LOQ) of 0.72 and 2.4 μg g^− 1, respectively. Precision values, expressed as the relative standard deviations (% RSD, n = 10) for 12 and 400 μg g^− 1, were 2.2% and 1.3%, respectively. The proposed procedure was applied toward the determination of total sulfur in samples of gasoline, kerosene, and diesel fuel commercialized in the city of Niterói/RJ, Brazil. The accuracy of the proposed method was evaluated by the determination of the total sulfur in three different standard reference materials (SRM): NIST 2723a (sulfur in diesel fuel oil), NIST 1616b (sulfur in kerosene), and NIST 2298 (sulfur in gasoline). The data indicate that the methodology can be successfully applied to these types of samples. Spiking tests, conducted with the analyzed samples, indicate that recoveries are between 97 and 103%.     

Usefulness of the chaotropic effect in sample preparation for chromatographic analysis of acidic xenobiotics in human plasma

In this study a new RP‐HPLC with photo‐diode array detection method for the determination of ibuprofen ((RS)‐2‐(4‐isobutylphenyl)propionic acid) in human plasma samples was developed. Samples were prepared by SPE and analyzed by an isocratic elution mode over a C₁₈ column using 80% methanol. A novel sample pretreatment method, based on the addition of ionic liquids possessing chaotropic ions to small human plasma sample (100 μL), was elaborated. 1‐Butyl‐3‐methylimidazolium chloride and 1‐butyl‐3‐methylimidazolium tetrafluoroborate (BMIM BF₄) were tested from the point of view of extraction yield. Quantification was based on calibration curve applying diclofenac as the internal standard. Owing to dilution of plasma sample by 2 mM aqueous solution of BMIM BF₄ before SPE, appropriate sample purification and extraction yields higher than 95% with precision lower than 2% can be achieved. Linear coefficients of correlation (r²) were >0.99 in the range of 0.3–5 μg/mL ibuprofen concentration in plasma. The limit of quantification was 65 ng/mL and the detection limit for ibuprofen was 19.5 ng/mL.     

Determination of chromium in whole blood by DRC–ICP–MS: spectral and non-spectral interferences

Quantification of chromium in whole blood has been performed by ICP–quadrupole MS. The spectrometer was equipped with a dynamic reaction cell (DRC) with ammonia as reaction gas. The rejection parameter q (RPq) of the DRC and the flow rate of ammonia (NH₃) were optimized and set at 0.7 and 0.6 mL min⁻¹, respectively. Blood was diluted 1:51 (v/v) with an aqueous solution containing 0.1 mg L⁻¹ NH₄OH, 0.1 g L⁻¹ EDTA, 5 mg L⁻¹ n-butanol, and 0.1‰ Triton X100. Non-spectral matrix effects observed when using the DRC were confirmed by use of vanadium. External calibration with blank and standard solutions prepared in purified water led to biased results for quality control samples. Standard addition calibration was therefore used and its validity verified. By comparing the slopes and calculating residues, it was proved that the plot obtained with standard additions and the plot obtained from blood samples of different concentrations were aligned down to 0.05 μg L⁻¹ after dilution.     

Determination of cadmium,mercury and lead in coal fly ash by slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry

Ultrasonic slurry sampling electrothermal vaporization isotope dilution inductively coupled plasma mass spectrometry (USS-ETV-ID-ICP-MS) has been applied to the determination of Cd, Hg and Pb in coal fly ash samples. Thioacetamide (TAC) was used as the modifier. Since the sensitivities of the elements studied in coal fly ash slurry and aqueous solution were quite different, isotope dilution method was used for the determination of Cd, Hg and Pb in these coal fly ash samples. The isotope ratios of each element were calculated from the peak areas of each injection peak. This method has been applied to the determination of Cd, Hg and Pb in NIST SRM 1633a coal fly ash reference material and a coal fly ash sample collected from Kaohsiung area. Analysis results of reference sample NIST SRM 1633a coal fly ash agreed satisfactorily with the certified values. The other sample determined by isotope dilution and method of standard additions was agreed satisfactorily. Precision was better than 6% for most of the determinations and accuracy was better than 4% with the USS-ETV-ID-ICP-MS method. Detection limits estimated from standard addition curves were in the range of 24–58, 6–28 and 108–110 ng g⁻¹ for Cd, Hg and Pb, respectively.