Stability of Zn–Ni–TiO<Subscript>2</Subscript> and Zn–TiO<Subscript>2</Subscript> nanocomposite coatings in near-neutral sulphate solutions

Zn–Ni–TiO₂ and Zn–TiO₂ nanocomposites were prepared by galvanostatic cathodic square wave deposition. X-ray diffraction analysis and scanning electron microscopy revealed that the occlusion of TiO₂ nanoparticles (spherical shaped with diameter between 19.5 and 24.2 nm) promotes the formation of the γ-Ni₅Zn₂₁ phase, changes the preferred crystallographic orientation of Zn from (101) and (102) planes to (002), and decreases the particle size of the metallic matrices. The stability of the nanocomposites immersed in near-neutral 0.05 mold m⁻³ Na₂SO₄ solution (pH 6.2) was investigated over 24 h. The initial open circuit potential for the Zn–Ni–TiO₂ and Zn–TiO₂ coatings were −1.32 and −1.51 V (vs. Hg/Hg₂SO₄), respectively, and changed to −1.10 and –1.49 V (vs. Hg/Hg₂SO₄) after 24 h of immersion. Data extracted from the steady state polarization curves demonstrated that the metal–TiO₂ nanocomposites have, with respect to the metal coatings, a higher corrosion potential in the case of the Zn–Ni alloy composite; a lower corrosion potential in the case of Zn-based nanocomposite albeit the predominant (002) crystallographic orientation; and a lower initial corrosion resistance due to the smaller grain size and higher porosity in the Zn–Ni–TiO₂ and Zn–TiO₂ nanocomposites. Morphological and chemical analyses showed that a thicker passive layer is formed on the surface of the Zn–Ni–TiO₂ and Zn–TiO₂ deposits. After 24 h of immersion in the sulphate solution, the Zn–Ni–TiO₂ coating has the highest corrosion stability due to the double-protective action created by the deposit’s surface enrichment in Ni plus the higher amount of corrosion products.     

Microwave dielectric properties of the 5.5Li<Subscript>2</Subscript>O–Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>–7TiO<Subscript>2</Subscript> ceramics

A new Li₂O–Nb₂O₅–TiO₂ (LNT) ceramic with the Li₂O:Nb₂O₅:TiO₂ mole ratio of 5.5:1:7 was prepared by solid state reaction route. The phase and structure of the ceramic were characterized by X-ray diffraction and scanning electron microscopy (SEM). The microwave dielectric properties of the ceramics were studied using a network analyzer. The microwave dielectric ceramic has low sintering temperature (∼1075°C) and good microwave dielectric properties of ε _r=42, Q×f=16900 GHz (5.75 GHz), and τ _f =63.7 ppm/°C. The addition of B₂O₃ can effectively lower the sintering temperature from 1075 to 875°C and does not induce degradation of the microwave dielectric properties. Obviously, the LNT ceramics can be applied to microwave low temperature-cofired ceramics (LTCC) devices.     

Study of phase transition of TiO<Subscript>2</Subscript>–CaO system

Electrical conductivity of TiO₂ doped with CaO has been measured at different temperatures for various molar ratios. The conductivity after initially remaining constant till about 140 °C increases with temperature due to the migration of vacancies created by doping. After attaining a maximum value at 240 °C, conductivity decreases due to the collapse of fluorite framework. A second rise in conductivity at high temperature beyond 400 °C indicates the phase transition of TiO₂, from anatase to rutile, which is confirmed by the differential scanning calorimetry results. X-ray powder diffraction, impedance measurements, and Fourier transform infrared spectral studies were also carried out for confirming the doping effect and phase transitions in TiO₂. Doping of TiO₂ with CaO shifts the transition to lower temperatures.     

In Situ Charge Characterization of TiO<Subscript>2</Subscript> and Cu–TiO<Subscript>2</Subscript> Nanoparticles in a Flame Aerosol Reactor

Charge distribution characteristics were investigated for nanoparticles synthesized in a diffusion flame aerosol reactor. The nanoparticles considered were pristine TiO₂ and Cu–TiO₂, with Cu dopant concentrations ranging from 1 to 5 wt% with particle size from 25 to 60 nm. In situ measurements were conducted by integrating a tandem differential mobility analyzer (TDMA) experimental setup with the flame aerosol reactor. A charging model was used to identify the important parameters that govern the two charging mechanisms (diffusion and thermo-ionization) in the flame and their relative importance at different operating parameters. The results indicate that TiO₂ and Cu–TiO₂ nanoparticles carry single as well as double unit charges. The charged fraction depends on particle size as well as on dopant concentration. The charged fraction increased with increasing particle size and decreased with copper dopant concentration. Measured charged fractions were similar for both the polarities at different mobility diameters. Based on the flame operating parameters, the calculations indicate that diffusion charging is dominant in the flame, which is consistent with the experimental results.     

Size-controllable synthesis of functional heterostructured TiO<Subscript>2</Subscript>–WO<Subscript>3</Subscript> core–shell nanoparticles

Mono and bicomponent TiO₂ and WO₃ nanoparticles were synthesized inside Vycor^® glass pores, by cycles of impregnation of the glass with the respective oxide precursor followed by its thermal decomposition. The impregnation-decomposition cycle (IDC) methodology promoted a linear mass increase of the glass matrix, and allowed tuning the nanoparticle size. X-ray diffraction and Raman spectroscopy data allowed identifying the formation of TiO₂ as anatase phase, while WO₃ is a mixture of the γ-WO₃ (monoclinic) and δ-WO₃ (triclinic) phases. High resolution transmission electron microscopy images revealed that for 3, 5, and 7 IDC, the TiO₂ nanoparticles obtained presented average diameters of 3.4, 4.3, and 5.1 nm, and the WO₃ nanoparticles have 2.9, 4.6, and 5.7 nm sizes. These TiO₂ and WO₃ monocomponent nanoparticles were submitted to IDC with the other oxide precursor, resulting in bicomponent nanoparticles. The broadening and shift of the Raman bands related to titanium and tungsten oxides suggest the formation of hetero-structure core–shell nanoparticles with tunable core sizes and shell thicknesses.     

Elastic properties of TeO<Subscript>2</Subscript>–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–Ag<Subscript>2</Subscript>O glasses

A series of glasses [(TeO₂) _x (B₂O₃)_1−x ]_1−y [Ag₂O] _y with x = 70 and y = 10, 15, 20, 25 and 30 mol% were synthesised by rapid quenching. Longitudinal and shear ultrasonic velocity were measured at room temperature and at 5 MHz frequency. Elastic properties, Poisson's ratio, microhardness, softening temperature and Debye temperature have been calculated from the measured density and ultrasonic velocity at room temperature. The experimental results indicate that the elastic constants depend upon the composition of the glasses and the role of the Ag₂O inside the glass network is discussed. Estimated parameters based on Makishima–Mackenzie theory and bond compression model were calculated in order to analyse the experimental elastic moduli. Comparison between the experimental elastic moduli data obtained in the study and the calculated theoretically by the mentioned above models has been discussed.     

Characterization and antibacterial functions of Ag–TiO<Subscript>2</Subscript> and W–TiO<Subscript>2</Subscript> nanostructured thin films prepared by sol-gel/laser-induced technique

A novel sol-gel/laser-induced technique (SGLIT) has been developed to form nanocrystalline titanium dioxide (TiO₂) based thin films with an improved antibacterial performance. TiO₂ precursor films loaded with W⁺⁶ and Ag⁺² ions (W–TiO₂, Ag–TiO₂) were prepared separately by sol-gel method and spin-coated on microscopic glass slides. As-dried films were subjected to KrF excimer laser pulses at optimized parameters to generate mesoporous anatase and rutile phases at room temperature. The anatase phase was obtained after irradiation with 10 laser pulses only at 75–85 mJ/cm² fluence in W–TiO₂ films. However, higher number of laser pulses and higher W⁺⁶ content favored the formation of rutile. Whereas Ag–TiO₂ films exhibited anatase up to 200 laser pulses at the same fluence. The films were characterized by using XRD, FEG-SEM, TEM and UV-Vis spectrophotometer to investigate the crystallographic structure, phase transformation, surface morphology, film thickness and the optical properties. A crystallite size of approximately 20 nm was achieved from the anatase prepared by SGLIT. The films exhibited an enhanced antibacterial function against E-Coli cells under the UV excitation.     

Magnetic and magnetoresistive properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–Sr<Subscript>2</Subscript>FeMoO<Subscript>6–δ</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoheterostructures

A method has been developed for fabricating nanoporous matrices based on anodic aluminum oxide for the deposition of ferromagnetic nanoparticles in them. The modes of deposition of strontium ferromolybdate thin films prepared by the ion-plasma method have been worked out, and the magnetic and magnetoresistive properties, structure, and composition of the films have been investigated. It has been revealed that the microstructure and properties of the strontium ferromolybdate films deposited by ionplasma sputtering depend on the deposition rate and the temperature of the substrate. Based on the measurement of the electrical resistivity of nanoheterostructures in a magnetic field, it has been found that the magnetoresistance reaches 14% at T = 15 K and B = 8 T, which is due to the manifestation of tunneling magnetoresistance.     

Influence of pH on the preparation of dispersed Ag–TiO<Subscript>2</Subscript> nanocomposite

In this paper, data concerning the effect of pH on the morphology of Ag–TiO₂ nanocomposite during photodeposition of Ag on TiO₂ nanoparticles is reported. TiO₂ nanoparticles prepared by sol–gel method were coated with Ag by photodeposition from an aqueous solution of AgNO₃ at various pH levels ranging from 1 to 10 in a titania sol, under UV light. The as-prepared nanocomposite particles were characterized by UV–vis absorption spectroscopy, transmission electron microscopy (TEM), X-ray diffraction (XRD), and N₂ adsorption/desorption method at liquid nitrogen temperature (−196 °C) from Brunauer–Emmett–Teller (BET) measurements. It is shown that at a Ag loading of 1.25 wt.% on TiO₂, a high-surface area nanocomposite morphology corresponding to an average of one Ag nanoparticle per titania nanoparticle was achieved. The diameter of the titania crystallites/particles were in the range of 10–20 nm while the size of Ag particles attached to the larger titania particles were 3 ± 1 nm as deduced from crystallite size by XRD and particle size by TEM. Ag recovery by photo harvesting from the solution was nearly 100%. TEM micrographs revealed that Ag-coated TiO₂ nanoparticles showed a sharp increase in the degree of agglomeration for nanocomposites prepared at basic pH values, with a corresponding sharp decrease in BET surface area especially at pH > 9. The BET surface area of the Ag–TiO₂ nanoparticles was nearly constant at around a value of 140 m² g⁻¹ at all pH from 1–8 with an anomalous maximum of 164 m² g⁻¹ when prepared from a sol at pH of 4, and a sharp decrease to 78 m² g⁻¹ at pH of 10.     

Fabrication of a nanoparticle TiO<Subscript>2</Subscript> photoelectrochemical cell utilizing a solid polymeric electrolyte of PAN–PC–LiClO<Subscript>4</Subscript>

A nanoparticle TiO₂ solid-state photoelectrochemical cell utilizing as a solid electrolyte of poly(acrylonitrile)–propylene–carbonate–lithium perchlorate (PAN–PC–LiClO₄) has been fabricated. The performance of the device has been tested in the dark and under illumination of 100-mW cm⁻² light. A nanoparticle TiO₂ film was deposited onto indium tin oxide-covered glass substrate by controlled hydrolysis technique assisted with spin-coating technique. The average grain size for the TiO₂ film is 76 nm. LiClO₄ salt was used as a redox couple. The room temperature conductivity of the electrolyte is 4.2 × 10⁻⁴ S cm⁻¹. A graphite electrode was prepared onto a glass slide by electron beam evaporation technique. The device shows the rectification property in the dark and shows the photovoltaic effect under illumination. The best J _sc and V _oc of the device were 2.82 μA cm⁻² and V _oc of 0.58 V, respectively, obtained at the conductivity of 4.2 × 10⁻⁴ S cm⁻¹ and intensity of 100 mW cm⁻². The J _sc was improved by about three times by introducing nanoparticle TiO₂ and by using a solid electrolyte of PAN–PC–LiClO₄ replacing PVC–PC–LiClO₄ in the device. The current transport mechanism of the cell is also presented in this paper.     

High-Temperature Heat Capacity of Zn<Subscript>2</Subscript>V<Subscript>2</Subscript>O<Subscript>7</Subscript>–Cu<Subscript>2</Subscript>V<Subscript>2</Subscript>O<Subscript>7</Subscript> Solid Solutions

Differential scanning calorimetry has been used to study the influence of temperature on the heat capacity of synthesized vanadates Zn₂V₂O₇, (Cu_0.56Zn_1.44)V₂O₇, and (Cu_1.0Zn_1.0)V₂O₇. It is found that dependences C_p = f(T) have extremes. The thermodynamic properties of Zn₂V₂O₇ have been determined.     

Synthesis and characterization of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript>–Ba<Subscript>0.9</Subscript>Sr<Subscript>0.1</Subscript>TiO<Subscript>3</Subscript> magnetoelectric composites with dielectric and magnetic properties

Composite structures consisting of (001)-oriented SrTiO₃ (STO)/La_0.7Sr_0.3MnO₃ (LSMO) films of 30 nm thickness, grown on an (001) Pb(Mg_1/3Nb_2/3)TiO₃– 28 mol.% PbTiO₃ piezoelectric relaxor-ferroelectric single-crystalline wafer were investigated by means of Wide-Angle X-ray Diffraction (WAXRD) in situ under influence of a d.c. electric field with strength E up to ±18 kV/cm. The WAXRD measurements of the films and substrate reflection profiles resulted in a determination of the strain s in the films and the substrate separately. The strained state of the STO/LSMO films is effectively controlled by a huge converse piezoelectric effect of the PMN-PT substrate. The coefficients of coupling between electric-field-induced out-of-plane strain in the films and in the substrate for the composite system STO/LSMO/PMN-PT are obtained.     

Large electrostrictive strain in lead-free Bi<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript>–BaTiO<Subscript>3</Subscript>–KNbO<Subscript>3</Subscript> ceramics

In the present work, (1−x)(0.935Bi_0.5Na_0.5TiO₃–0.065BaTiO₃)–xKNbO₃ (BNT–BT–KN, BNT–BT–100xKN) ceramics with x ranging from 0 to 0.1 were prepared by the conventional ceramic fabrication process. A large electrostrictive coefficient of ∼10⁻² m⁴ C⁻² is obtained with the composition x ranging from 0.02 to 0.1, which is close to the well-known electrostrictive material Pb(Mg_1/3Nb_2/3)O₃. Under an electric field of 4 kV/mm, the electrostrictive strain can reach as high as 0.08%. Besides, the electric field induced strain behavior indicates a temperature independent behavior within the temperature range of 20 to 150°C. The large electrostrictive strain is suggested to be ascribed to the formation of non-polar (NP) phase developed by the KNbO₃ substitution, and the high electrostrictive coefficient of BNT–BT–KN ceramics makes them great candidates to be applied in the new solid-state actuators.     

Influence of Matrix Nature on the Structural Characteristics of In<Subscript>2</Subscript>O<Subscript>3</Subscript>–CeO<Subscript>2</Subscript> and SnO<Subscript>2</Subscript>–CeO<Subscript>2</Subscript> Composites Fabricated by the Impregnation Method

The structural characteristics, valence states, and distribution of cerium ions between the components in In₂O₃–CeO₂ and SnO₂–CeO₂ nanocomposites fabricated using the impregnation method were studied. X-ray photoelectron spectroscopy (XPS) and energy-dispersive X-ray spectroscopy (EDX) were used to show that, during impregnation, cerium ions are not included into In₂O₃ crystals and are disposed only on their surface in the form of nano-sized crystallites or amorphous clusters. On the other side, under the contact of CeO₂ clusters with a surface of SnO₂ matrix crystals, cerium ions penetrate into the surface layer of these crystals. In contrast to an In₂O₃–CeO₂ system, where the addition of CeO₂ does not affect the conduction activation energy, where cerium oxide is added to SnO₂, the observed increase in the resistance of a SnO₂–CeO₂ composite is accompanied by a sufficient increase in activation energy. These data and the XPS spectra confirm the modification of the surface layers of conductive SnO₂ crystals as, a result of the penetration of cerium ions into these layers.     

Electrical properties of polycrystalline TiO<Subscript>2·</Subscript> Thermoelectric power

The present work determined thermoelectric power for high-purity polycrystalline TiO₂ at elevated temperatures (1,123–1,323 K) and in the gas phase of controlled oxygen activity, . The slope of the thermoelectric power vs logp(O₂) is 1/10, instead of 1/6 expected by the theory and observed for TiO₂ single crystal. The discrepancy between the two is considered in terms of the effect of the local grain boundary structure on thermoelectric power. A comparison between the electrical conductivity and thermoelectric power data indicates that the oxygen activity values related to the n–p transition point determined by thermoelectric power are lower than those determined by electrical conductivity. This project was performed as part of UNSW R&D program on solar–hydrogen.     

Phase formation in the BaCO<Subscript>3</Subscript>–PbO–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>–Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> system

Features of the formation of lead-ferroniobate compounds in the xBaCO₃–(1 – x)PbO–Fe₂O₃–Nb₂O₅ system by solid-phase synthesis are investigated. For perovskite-type lead-ferroniobate solid solution, a single-phase concentration region is revealed at 1233 K. The crystalline structures of the synthesized compounds are refined using Rietveld analysis and the Pm3?m and R3m space groups. Ceramic samples of lead ferroniobate are studied by scanning electron microscopy.     

Sol–gel synthesis and characterization of Li<Subscript>2</Subscript>CO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite solid electrolytes

Composite solid electrolytes in the system (1???x)Li₂CO₃–xAl₂O₃, with x?=?0.0–0.5 (mole), were synthesized by a sol–gel method. The synthesis carried out at low temperature resulted in voluminous and fluffy products. The obtained materials were characterized by X-ray diffraction, differential scanning calorimetry, scanning electron microscopy/energy-dispersive X-ray, Fourier transform infrared spectroscopy and AC impedance spectroscopy. Structural analysis of the samples showed an amorphous feature of Li₂CO₃ and traces of α-LiAlO₂, γ-LiAlO₂ and LiAl₅O₈. The prepared composite samples possess high ionic conductivities at 130–180 °C on account of the presence of lithium aluminates as well as the formation of a high concentration of an amorphous phase of Li₂CO₃ via this sol–gel preparative technique.     

Specific heat of the [NH<Subscript>2</Subscript>(CH<Subscript>3</Subscript>)<Subscript>2</Subscript>]<Subscript>2</Subscript>ZnCl<Subscript>4</Subscript> crystal in the temperature region 80–300 K

The specific heat of [NH₂(CH₃)₂]₂ZnCl₄ was measured calorimetrically in the temperature region 80–300 K. As the temperature T decreases, the C _p (T) dependence indicates a phase transition sequence, with the phase transition at T₆=151 K observed for the first time. The thermodynamic characteristics of the crystal were refined. The transformation occurring at T₂=298.3 K is shown to be an incommensurate-commensurate phase transition.     

Electrical switching in the MoO<Subscript>3</Subscript>–WO<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript> and MoO<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

High field electrical switching on blown films of MoO₃(60%)–P₂O₅(40%), MoO₃(50%)–WO₃(10%)–P₂O₅(40%), and MoO₃(45%)–WO₃(15%)–P₂O₅(40%) having different thicknesses was studied and compared. Switching was observed using two terminal samples. S-type current–voltage characteristic (current-controlled negative resistance—CCNR) with memory was observed in molybdenum–phosphate glasses, but N-type characteristic (voltage-controlled negative resistance—VCNR) with threshold in tungsten–molybdenum–phosphate glasses was observed. The important observation was that with the addition of WO₃ to binary MoO₃–P₂O5 led to a change of I–V characteristic from CCNR with memory to VCNR with threshold. The measurements of density and molar volume showed linear relation between MoO₃ content and density which decreased with the increase of MoO₃ content. The samples’ thickness had no significant effect on threshold voltage. The attained results also indicated that the electrode material had no effect on switching property of devices. The switching behavior of the devices did not show any dependence on the polarity of the applied voltage. In terms of the effect of heat on the switching behavior of molybdenum–phosphate glasses, it was found that threshold voltage decreases with increasing of temperature. Finally, the switching phenomenon was explained by thermal (formation of crystalline filaments) and electronic models.