Single, binary and multi-component adsorption of some anions and heavy metals on environmentally friendly Carpobrotus edulis plant

A low-cost adsorbent and environmentally friendly adsorbent from Carpobrotus edulis plant was used for the removal of NO(3)(-), H(2)PO(4)(-), Pb(2+) and Cd(2+) ions from single, binary and multi-component systems. The efficiency of the adsorbent was studied using batch adsorption technique under different experimental conditions by varying parameters such as pH, initial concentration and contact time. In single component systems, the dried C. edulis has the highest affinity for Pb(2+), followed by NO(3)(-), Cd(2+) and H(2)PO(4)(-), with adsorption capacities of 175mg/g, 125mg/g, 28mg/g and 26mg/g, respectively. These results showed that the adsorption of NO(3)(-) and H(2)PO(4)(-) ions from single and binary component systems can be successfully described by Langmuir and Freundlich isotherms. Freundlich adsorption model, showed the best fit to the single and binary experimental adsorption data. These results also indicated that the adsorption yield of Pb(2+) ion was reduced by the presence of Cd(2+) ion in binary metal mixture. The competitive adsorption of NO(3)(-), H(2)PO(4)(-), Pb(2+) and Cd(2+) ions on dried C. edulis plant shows that NO(3)(-) and H(2)PO(4)(-) anions are able to adsorb on different free binding sites and Pb(2+) and Cd(2+) cations are able to adsorb on the same active sites of C. edulis particles. The dried C. edulis was found to be efficient in removing nitrate, phosphate, cadmium and lead from aqueous solution as compared to other adsorbents already used for the removal of these ions.     

Determination of common inorganic anions and cations by non-suppressed ion chromatography with column switching

An ion chromatography (IC) method has been proposed for the determination of seven common inorganic anions (F(-), H(2)PO(4)(-), NO(2)(-), Cl(-), Br(-), NO(3)(-), and SO(4)(2-)) and/or five common inorganic cations (Na(+), NH(4)(+), K(+), Mg(2+), and Ca(2+)) using a single pump, a single eluent and a single detector. The present system used cation-exchange and anion-exchange columns connected in series via a single 10-port switching valve. The 10-port valve was switched for the separation of either cations or anions in a single chromatographic run. When 1.0mM trimellitic acid (pH 2.94) was used as the eluent, the seven anions and the five cations could be separated on the anion-exchange column and the cation-exchange column, respectively. The elution order was found to be F(-)相似文献   

Matrix influences on the determination of common ions by using ion chromatography part 1--determination of inorganic anions

Ion chromatography is the most popular instrumental analytical method used for the determination of anions and cations in water and wastewater. Isocratic ion chromatography with suppressed conductivity detection is frequently used in laboratories carrying out routine analyses of inorganic anions. The paper presents the results of the research into the influence of selected inorganic anions dominant in environmental samples (Cl(-), NO(3)(-), SO(4)(2-)) on the possibility of simultaneous determination of F(-), Cl(-), NO(2)(-), NO(3)(-), PO(4)(3-) and SO(4)(2-) with the application of this most popular ion chromatography type in standard separation conditions. Four Dionex and four Metrohm anion-exchange columns were tested in standard separation conditions recommended by their manufacturers with both standard solutions and environmental samples with complex matrix.     

Crystallographic evidence for oxygen acceptor directionality in oxyanion hydrogen bonds.

A survey of 2632 D-H...O-A hydrogen bonds in crystal structures (where D is any atom and A is the central atom of a trigonal planar (A = C, N) or tetrahedral (A = P, S, Cl, As, Se, Cr, Mo) oxyanion, has established the existence of a distinct directionalities at the oxygen atom acceptors. The directionality depends primarily on the geometry of the oxyanion. With the trigonal planar oxyanions NO3-, HCO3-, and CO32-, the average H...O-A angle is 115 +/- 12 degrees and there is a clear preference for the hydrogen to lie within the plane of the anion. With the tetrahedral oxyanions H2PO4-, HPO42-, HSO4-, SO42-, ClO4-, H2AsO4-, HAsO42-, AsO43-, HSeO4-, SeO42-, CrO42-, and MoO42-, the average H...O-A angle is 122 +/- 12 degrees , and there is a weak preference for eclipsed H...O-X-O dihedral angles. The observed directionality closely coincides with minima on electrostatic potential surfaces calculated for the anions.     

Triphenylene based copper ensemble for the detection of cyanide ions

The binding behavior of triphenylene based copper ensemble prepared in situ has been investigated toward various anions (F(-), Cl(-), Br(-), I(-), CH(3)COO(-), H(2)PO(4)(-), NO(3)(-), OH(-), ClO(4)(-), CN(-), CO(3)(-) and SO(4)(-)) by UV-vis and fluorescence spectroscopy. Among various anions tested, 1-Cu(2+) ensemble shows selective and sensitive response towards cyanide ions and responds to CN(-) ions even in the presence of bovine serum albumin and in blood serum milieu. Further, as practical application of compound 1, we utilized the TLC strips coated with THF solution of 1 for the solid state detection of copper and cyanide ions.     

Radiotracer Study of the Specific Adsorption of Anions on Metal Oxides in Acid Media: An Experimental Approach

The specific adsorption of anions (HSO(4)(-), H(2)PO(4)(-), and Cl(-)) was studied at Fe(2)O(3), ZnO, and CuO surfaces by the radiotracer technique in strongly acidic medium (1 M HClO(4)). A significant specific adsorption of HSO(4)(-) and H(2)PO(4)(-) ions was found in all cases studied while no measurable adsorption of Cl(-) ions was observed. In the cases of ZnO and CuO, the specific adsorption takes place over the course of continuous dissolution of the oxide. Copyright 2000 Academic Press.     

Indirect spectrophotometric determination of sulphide with the ternary complex system Ag(I)-phen-BPR

Trace amounts of sulphide can be determined from its effect on the ternary complex system of Ag(+), Bromopyrogallol Red (BPR), and 1,10-phenanthroline (phen). Sulphide in the range 5-120 ng/ml causes a decrease in absorption, that is a linear function of the concentration. Common metal ions such as Na(+), K(+), Ca(2+), Mg(2+), Al(3+), Mn(2+) and anions such as F(-), Cl(-), NO(-)(3), SO(2-)(4), CO(2-)(3), and PO(3-)(4) at the 4 mug/ml level or more do not interfere, but I(-) or CN(-) must be absent.     

Studies on the effects of metal ions and counter anions on the aggregate behaviors of meso-tetrakis(p-sulfonatophenyl)porphyrin by absorption and fluorescence spectroscopy

The aggregation behaviors of meso-tetrakis(p-sulfonatophenyl)porphyrin (TPPS) in the function of metal ions and their counter anions (Cl(-), SO(4)(2-), and NO(3)(-)) were investigated by absorption, fluorescence spectroscopy and resonance scattering spectrum. It was shown that the TPPS J-aggregates could be effectively promoted by metal ions under lower ionic strength. Moreover, the prominent effects of counter ions (Cl(-), SO(4)(2-), and NO(3)(-)) on TPPS J- and/or H-aggregate formation at higher ionic strength were observed. These results suggested that the counter anions play a significant role in the formation of TPPS J- and/or H-aggregates and their conversion each other. Very interestingly, the absorption spectrum of metal ions investigated except for Co(2+) leaves a WINDOW from ca. 450 to 550nm centered at 490nm in which the absorption of Cu(2+) or Ni(2+) ions per se was very weak. The spectrum window might be really significant in avoiding possible spectrum interferences when porphyrins are chosen as spectrometric reagents for the determination of metal ions based on J-aggregation.     

Multi-competitive interaction of As(III) and As(V) oxyanions with Ca(2+), Mg(2+), PO(3-)(4), and CO(2-)(3) ions on goethite

Complex systems, simulating natural conditions like in groundwater, have rarely been studied, since measuring and in particular, modeling of such systems is very challenging. In this paper, the adsorption of the oxyanions of As(III) and As(V) on goethite has been studied in presence of various inorganic macro-elements (Mg(2+), Ca(2+), PO(3-)(4), CO(2-)(3)). We have used 'single-,' 'dual-,' and 'triple-ion' systems. The presence of Ca(2+) and Mg(2+) has no significant effect on As(III) oxyanion (arsenite) adsorption in the pH range relevant for natural groundwater (pH 5-9). In contrast, both Ca(2+) and Mg(2+) promote the adsorption of PO(3-)(4). A similar (electrostatic) effect is expected for the Ca(2+) and Mg(2+) interaction with As(V) oxyanions (arsenate). Phosphate is a major competitor for arsenate as well as arsenite. Although carbonate may act as competitor for both types of As oxyanions, the presence of significant concentrations of phosphate makes the interaction of (bi)carbonate insignificant. The data have been modeled with the charge distribution (CD) model in combination with the extended Stern model option. In the modeling, independently calculated CD values were used for the oxyanions. The CD values for these complexes have been obtained from a bond valence interpretation of MO/DFT (molecular orbital/density functional theory) optimized geometries. The affinity constants (logK) have been found by calibrating the model on data from 'single-ion' systems. The parameters are used to predict the ion adsorption behavior in the multi-component systems. The thus calibrated model is able to predict successfully the ion concentrations in the mixed 2- and 3-component systems as a function of pH and loading. From a practical perspective, data as well as calculations show the dominance of phosphate in regulating the As concentrations. Arsenite (As(OH)(3)) is often less strongly bound than arsenate (AsO(3-)(4)) but arsenite responses less strongly to changes in the phosphate concentration compared to arsenate, i.e., deltalogc(As(III))/deltalogc(PO(4)) approximately 0.4 and deltalogc(As(V))/deltalogc(PO(4)) approximately 0.9 at pH 7. Therefore, the response of As in a sediment on a change in redox conditions will be variable and will depend on the phosphate concentration level.     

Sampling and analysing mixtures of sulphate, sulphite, thiosulphate and polythionate

Interpreting the redox chemistry of sulphur in aqueous systems requires the analysis of mixtures of various sulphoxy anions. Previous methods have been too involved to permit high sample throughout if good quality control is to be maintained. Methods based on ion chromatography have been developed for the direct determination of SO(2-)(4), SO(2-)(3), S(2)O(2-)(3), and SCN(-). The determination of thiocyanate permits the indirect determination of polythionates by treatment with cyanide. Formate, acetate, F(-), Cl(-), CO(2-)(3), and PO(3-)(4), do not interfere, but NO(-)(2) and NO(-)(3) interfere with determination of SO(2-)(3),. The sample preservation treatment includes addition of formaldehyde, cation-exchange and cold storage, to retard oxidation of S(2)O(2-)(3), and SO(2-)(3), and inhibits the rearrangement of SO(2-)(3),/S(2)O(2-)(3),/S(n)O(2-)(6), mixtures caused by bimolecular nucleophilic displacement (S(N)2) reactions. Treated samples may be stored for up to 6 weeks with only minor loss of thiosulphate.     

A naphthalene exciplex based Al3+ selective on-type fluorescent probe for living cells at the physiological pH range: experimental and computational studies

2-((Naphthalen-6-yl)methylthio)ethanol (HL) was prepared by one pot synthesis using 2-mercaptoethanol and 2-bromomethylnaphthalene. It was found to be a highly selective fluorescent sensor for Al(3+) in the physiological pH (pH 7.0-8.0). It could sense Al(3+) bound to cells through fluorescence microscopy. Metal ions like Mn(2+), Fe(3+), Co(2+), Ni(2+), Cu(2+), Zn(2+), Ag(+), Cd(2+), Hg(2+), Cr(3+) and Pb(2+) did not interfere. No interference was also observed with anions like Cl(-), Br(-), F(-), SO(4)(2-), NO(3)(-), CO(3)(2-), HPO(4)(2-) and SCN(-). Experimentally observed structural and spectroscopic features of HL and its Al(3+) complex have been substantiated by computational calculations using density functional theory (DFT) and time dependent density functional theory (TDDFT).     

Anion binding to a ferric porphyrin complexed with per-O-methylated beta-cyclodextrin in aqueous solution

5,10,15,20-Tetrakis(4-sulfonatophenyl)porphinato iron(III) (Fe(III)TPPS) forms a very stable 1:2 complex with heptakis(2,3,6-tri-O-methyl)-beta-cyclodextrin (TMe-beta-CD), whose iron(III) center is located at a hydrophobic cleft formed by two face-to-face TMe-beta-CD molecules. Various inorganic anions (X(-)) such as F(-), Cl(-), Br(-), I(-), N(3)(-), and SCN(-) coordinate to Fe(III)TPPS(TMe-beta-CD)(2) to form five-coordinate high-spin Fe(III)TPPS(X)(TMe-beta-CD)(2), while no coordination occurs with ClO(4)(-), H(2)PO(4)(-), NO(3)(-), and HSO(4)(-). Except for F(-), none of the anions investigated coordinate to Fe(III)TPPS in the absence of TMe-beta-CD due to extensive hydration to the anions as well as to Fe(III)TPPS. The present system shows a high selectivity toward the N(3)(-) anion. The thermodynamics suggests that Lewis basicity, hydrophilicity, and shape of an X(-) anion are the main factors to determine the stability of the Fe(III)TPPS(X)(TMe-beta-CD)(2) complex.     

New terphenyl based mercury ensemble for detection of acetate ions in a plasma like system

A new terphenyl based chemosensor 3 has been designed and synthesized. The binding behavior of 3 and its chemosensing ensemble 3-Hg toward various anions (F(-), Cl(-), Br(-), I(-), HSO(4)(-), H(2)PO(4)(-), CH(3)COO(-), NO(3)(-), N(3)(-), SO(4)(2-), SO(3)(2-), and Cr(2)O(7)(2-)) has been investigated by UV-Vis, fluorescence and NMR spectroscopy. Compound 3 shows a sensitivity for both F(-) and CH(3)COO(-) ions among various anions tested, whereas the ensemble 3-Hg shows a better selectivity for CH(3)COO(-) ions. The ensemble is utilized for CH(3)COO(-) recognition in a blood plasma like system.     

Determination of trace anions in liquefied petroleum gas using liquid absorption and electrokinetic migration for enrichment followed by ion chromatography

A simple sample enrichment technique, electrokinetic migration enrichment in single phase using a designed device, coupled with ion chromatography is presented for the determination of four anions (H(2)PO(4)(-), Cl(-), NO(3)(-), and SO(4)(2-)) in liquefied petroleum gas by liquid adsorption. The electrokinetic migration enrichment is based on the phenomenon of ion electrokinetic migration to the opposite electrode. When the anions migrated to the anode in a smaller volume chamber under the electric field, the concentration was realized. The main parameters affecting enrichment efficiency of applied voltage and enrichment time were investigated. The ion chromatography condition for anions separation was also studied. Under the optimal electrokinetic migration enrichment and ion chromatography conditions, the four anions were detected simultaneously with good linear relationship (r(2) = 0.9908-0.9968) and high precisions (less than 5% of the relative standard deviations of peak areas). The limits of detection of anions (S/N of 3) were in the range of 8-600 μg L(-1). The enrichment factors of the four anions ranged from 3.1 to 5.8. The established method was successfully applied to the analysis of the trace anions in liquefied petroleum gas by liquid adsorption with satisfactory results. The advantages of this method are simple operation and low cost.     

Adsorption of phosphate and nitrate anions on ammonium-functionalized MCM-48: effects of experimental conditions

In this study, ammonium-functionalized MCM-48 (Mobil Composite Material No. 48) was used as an adsorbent to remove nitrate (NO(-)(3)) and monobasic phosphate (H(2)PO(-)(4)) anions from aqueous solutions. The effects of operating conditions such as temperature, adsorbent loading, initial anion concentration, pH, and the presence of competitive ions on the adsorption performances were examined. Results showed that adsorption capacity decreased with increasing temperature. The adsorption capacity increased with adsorbent loading and initial anion concentration. The removal of nitrate was maximum at pH<8, while phosphate removal was maximized at pH 5. The adsorption was almost unaffected by the presence of competitive ions in the case of phosphate anions. However, their presence adversely affected nitrate adsorption. Desorption of both anions was rapidly achieved within 10 min using NaOH at 0.01 M. Regeneration tests showed that the adsorbent retained its capacity after 5 adsorption-desorption cycles.     

Anion effect on the nanostructure of a metal ion binding self-assembling peptide

Effects of copper salts containing different anions (SO(4)(2)(-), Cl(-), and NO(3)(-)) on the self-assembly of a designed peptide EAK16(II)GGH with affinity for Cu(2+) have been investigated. The peptide secondary structure, self-assembled nanostructures, and surface activity were observed to depend strongly on the type of anion. Over a salt concentration range from 0.05 to 10.0 mM, SO(4)(2)(-) induced long fiber formation, whereas Cl(-) and NO(3)(-) caused short fiber formation. The fiber length increased with copper sulfate concentration, but the concentration of copper chloride and copper nitrate did not affect the peptide nanostructures significantly. Analysis by Fourier transform infrared spectroscopy (FTIR) revealed that the addition of the copper salts tended to cause the peptide conformation to change from alpha-helix/random coil to beta-sheet, the extent to which depended on the anion type. This evidence of the anion effect was also supported by surface tension measurements using the axisymmetric drop shape analysis-profile (ADSA-P) technique. An explanation for the effect of anions on the peptide self-assembly was proposed. The divalent anion SO(4)(2)(-) might serve as a bridge by electrostatically interacting with two lysine residues from different peptide molecules, promoting beta-sheet formation. The extensive beta-sheet formation may further promote peptide self-assembly into long fibers. On the other hand, monovalent anions Cl(-) and NO(3)(-) may only electrostatically interact with one charged residue of the peptide; hence, a mixed secondary structure of alpha-helix/random coil and beta-sheet was observed. This observation might explain the predominant formation of short fibers in copper chloride and copper nitrate solutions.     

有机酸与无机阴离子的梯度离子色谱法分析研究

研究了用离子色谱法梯度洗脱抑制电导检测器分析有机酸与无机阴离子的色谱条件,建立了最佳梯度程序。用阴离子交换分离,选用去离子水、氢氧化钠和甲醇作淋洗液,分别对５种二元有机酸和３种无机阴离子做二元梯度淋洗,对１０种多元有机酸和３种无机阴离子做三元梯度淋洗。方法用于果汁饮料与柠檬酸发酵液的测定,结果令人满意。     

Effect of different salts and detergents on luciferin-luciferase luminescence of the enchytraeid Fridericia heliota

The study addresses the effect produced by different inorganic salts and detergents (SDS, Triton X-100, the Tween series) on the ATP-dependent bioluminescent reaction catalyzed by the luciferase of the new earthworm species Fridericia heliota (Annelida: Clitellata: Oligochaeta: Enchytraeidae). It has been shown that the effect of divalent metal salts on luminescence is determined by the action of cations. Three of them - Mg(2+), Mn(2+) and Ca(2+) - can stimulate luciferase activity at concentrations varying within a wide range, and Mn(2+) can act as a 100%-effective substitute for Mg(2+) in F. heliota luminescence reaction in vitro. The inhibitory effect of monovalent metal salts on luminescence is largely determined by the action of the anion part of the molecule. The effectiveness of the inhibitory effect of anions increases in the following order: Cl(-)相似文献   

Reversed-phase liquid chromatograhy/electrospray ionization tandem mass spectrometry for analysis of perchlorate in water

A new reversed-phase liquid chromatograhy/electrospray ionization tandem mass spectrometry method was developed for the analysis of perchlorate in water. The improved separation of perchlorate from common anions along with sample dilution effectively reduced matrix effects, primarily ion suppression caused by common anions. The (18)O-enriched perchlorate used as an internal standard provided further compensation for potential changes associated with instrument sensitivity, retention time shifting, peak broadening, ion suppression, and other matrix effects. The mean recoveries and relative standard deviations were 92-107% and 2.5-9.5% for simulated water matrix spikes at 0.05-1.0 microg/L, and 80-106% and 3.8-13% for real water sample matrix spikes at 2.0 microg/L, respectively. The method detection limits were 0.007 microg/L for reagent water and 0.014 microg/L for the simulated water matrix that contained 100 mg/L of SO(4)(2-), CO(3)(2-), and Cl(-) anions; 2 mg/L of PO(4)(3-) as P and NO(3)(-) as N; and 0.1 mg/L of Br(-), BrO(3)(-), ClO(2)(-), ClO(3)(-), and F(-) anions in reagent water, respectively. When using cartridge pretreatment to remove problematic SO(4)(2-), CO(3)(2-), and Cl(-) anions, the minimum reporting level could be set to 0.05 microg/L or lower. With 10-fold dilution, the minimum reporting level was conservatively set to 0.5 microg/L.