Li<Subscript>0.99</Subscript>Ti<Subscript>0.01</Subscript>FePO<Subscript>4</Subscript>/C composite as cathode material for lithium ion battery

Three kinds of LiFePO₄ materials, mixed with carbon (as LiFePO₄/C), doped with Ti (as Li_0.99Ti_0.01FePO₄), and treated both ways (as Li_0.99Ti_0.01FePO₄/C composite), were synthesized via ball milling by solid-state reaction method. The crystal structure and electrochemical behavior of the materials were investigated using X-ray diffraction, SEM, TEM, cyclic voltammetry, and charge/discharge cycle measurements. It was found that the electrochemical behavior of LiFePO₄ could be increased by carbon coating and Ti-doping methods. Among the materials, Li_0.99Ti_0.01FePO₄/C composite presents the best electrochemical behavior, with an initial discharge capacity of 154.5 mAh/g at a discharge rate of 0.2 C, and long charge/discharge cycle life. After 120 cycles, its capacity remains at 92% of the initial capacity. The Li_0.99Ti_0.01FePO₄/C composite developed here can be used as the cathode material for lithium ion batteries.     

LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> and LiCoO<Subscript>2</Subscript> composite cathode materials obtained by mechanical activation

New composite cathode materials xLiMn₂O₄/(1 ? x) LiCoO₂(x = 0.7, 0.6, 0.5 и 0.4) were obtained by mechanical activation. According to scanning electron microscopy data, the process was accompanied by pronounced dispersion and fine mixing of the initial components. In the course of the preparation and electrochemical cycling of the composites, LiMn₂O₄ and LiCoO₂ partially reacted, leading to the replacement of manganese with cobalt in the structure of spinel, which was detected by powder X-ray diffraction (XRD), IR and X-ray photoelectron spectroscopy (XPS), and cyclic chronopotentiometry. The specific discharge capacity of composites was ～100 mAh/g.     

Synthesis and electrochemical properties of yttrium-doped LiMn<Subscript>0.98</Subscript>Y<Subscript>0.02</Subscript>O<Subscript>2</Subscript> for lithium secondary batteries

Yttrium-doped lithium manganese oxide (LiMn_0.98Y_0.02O₂) was prepared by ion exchange of lithium for sodium in NaMn_0.98Y_0.02O₂ precursors obtained by using rheological phase reaction method. This material had small particle size, which was composed of grain size of about 100 nm. Especially, LiMn_0.98Y_0.02O₂ delivered the initial discharge capacity of about 191 mA h g⁻¹ at room temperature when cycled between 2.0 and 4.4 V vs Li/Li⁺. Moreover, it showed an excellent cycling behavior, its specific capacity remained above 173 mA h g⁻¹ after 20 cycles, and the material did not transform into spinel structure during the electrochemical cycling according to the cyclic voltammograms and X-ray powder diffraction. The electrochemical results revealed that the doping of Y³⁺ improved the performance of LiMnO₂ considerably.     

Electrochemical properties of nano-crystalline LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> synthesized by polymer-pyrolysis method

LiNi_0.5Mn_1.5O₄ powders were prepared through polymer-pyrolysis method. XRD and TEM analysis indicated that the pure spinel structure was formed at around 450 °C due to the very homogeneous intermixing of cations at the atomic scale in the starting precursor in this method, while the well-defined octahedral crystals appeared at a relatively high calcination temperature of 900 °C with a uniform particle size of about 100 nm. When cycled between 3.5 and 4.9 V at a current density of 50 mA/g, the as prepared LiNi_0.5Mn_1.5O₄ delivered an initial discharge capacity of 112.9 mAh/g and demonstrated an excellent cyclability with 97.3% capacity retentive after 50 cycles.     

Effects of Ni-ion doping on electrochemical characteristics of spinel LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> powders prepared by a spray-drying method

Spinel LiMn_2−x Ni _x O₄ compounds doped with a range of Ni (x=0–0.06) were synthesized by a spray-drying method. The structure and morphology characteristics of the powders were studied in detail by means of X-ray diffraction (XRD), scanning electron microscopy, and transmission electron microscopy. The XRD data reveal that all the samples have well-defined spinel structure, but, with the increase in Ni content, the doped lithium manganese spinels have smaller lattice constant. The undoped and doped spinel LiMn₂O₄ particles are fine, narrowly distributed, and well crystallized. The electrochemical characteristics of the samples are measured in the coin-type cells in a potential range of 3.2–4.35 V vs Li/Li⁺. All cyclic voltammogram curves exhibit two pairs of redox reaction peaks, but, among them, there are some differences about the peak split. With the increase in the Ni content, the specific capacities of the samples decrease slightly, but their cyclic ability increases.     

Synthesis and electrochemical properties of Ca-doped LiNi<Subscript>0.8</Subscript>Co<Subscript>0.2</Subscript>O<Subscript>2</Subscript> cathode material for lithium ion battery

LiNi_0.8Co_0.2O₂ and Ca-doped LiNi_0.8Co_0.2O₂ cathode materials have been synthesized via a rheological phase reaction method. X-ray diffraction studies show that the Ca-doped material, and also the discharged electrode, maintains a hexagonal structure even when cycled in the range of 3.0–4.35 V (vs Li⁺/Li) after 100 cycles. Electrochemical tests show that Ca doping significantly improves the reversible capacity and cyclability. The improvement is attributed to the formation of defects caused by the partial occupancy of Ca²⁺ ions in lithium lattice sites, which reduce the resistance and thus improve the electrochemical properties.     

An electrochemical investigation on (MoO<Subscript>3</Subscript>+PVP+PVA) nanobelts for lithium batteries

Molybdenum trioxide (MoO₃) xerogel films modified with poly(vinyl alcohol)+poly(vinyl pyrrolidone) (PVP+PVA) polyblends were obtained by ion-exchange method with sol-gel technique. Investigations were conducted using X-ray “diffractometry”, Fourier transform infrared spectroscopy, and cyclic voltammetry. The results show that the H atoms in polyblend are H-bonded with the O atoms in the Mo=O bonds of MoO₃ xerogel, which effectively shield the electrostatic interaction between MoO₃ interlayer and Li⁺ ions when MoO₃ xerogel is modified by the intercalation of (PVP+PVA). The reversibility of the insertion/extraction of Li⁺ ions is greatly improved by the modification with polyblend of MoO₃ nanocomposite films. MoO₃ and (PVP+PVA) _x MoO₃ (x = 0, 0.5) nanobelts were obtained by a simple hydrothermal process from MoO₃ sol. The electrochemical cells with configuration Li/(LiPF₆+EC+DMC)/MoO₃ modified by (PVP+PVA) were fabricated and their discharge profiles studied.     

Preparation and electrochemical properties of V<Subscript>2</Subscript>O<Subscript>5</Subscript> submicron-belts synthesized by a sol–gel H<Subscript>2</Subscript>O<Subscript>2</Subscript> route

One-dimensional (1D) submicron-belts of V₂O₅ have been prepared by a sol–gel route using V₂O_5, H₂O₂ and aniline as starting materials. Thermogravimetric and differential thermal analysis, X-ray diffraction, Fourier transform infrared spectroscopy and scanning electron microscopy were employed to characterize the samples. Electrochemical behaviors as cathode material in rechargeable lithium-ion batteries were investigated by galvanostatic charge–discharge measurement and cyclic voltammeter. The results showed that the synthesized V₂O₅ appeared to be submicron-belts and orthorhombic structure. The V₂O₅ submicron-belts exhibited a high initial discharge capacity of 346 mAh/g and stayed 240 mAh/g after 20 cycles at 0.1 C discharge rate in the potential region 1.8–4.0 V.     

Preparation and characterization of LiFePO<Subscript>4</Subscript> from NH<Subscript>4</Subscript>FePO<Subscript>4</Subscript>·H<Subscript>2</Subscript>O under different microwave heating conditions

Olivine-type LiFePO₄ is a very promising polyanion-type cathode material for lithium-ion batteries. In this work, LiFePO₄ with high specificity capacity is obtained from a novel precursor NH₄FePO₄·H₂O via microwave processing. The grains grow up in the duration of sintering until they reach the decomposition temperature. The apparent conductivity of the samples rises rapidly with the irradiation time and influences the electrochemical performance of the material greatly at high current density. As a result, the LiFePO₄ cathode material obtained with a sintering time of 15 min has good electrochemical performance. Between 2.5 and 4.2 V versus Li, a reversible capacity is as high as 156 mAh g⁻¹ at 0.05 C.     

Synthesis and characterization of submicron size particles of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> by microemulsion route

Among the various positive electrode materials investigated for Li-ion batteries, spinel LiMn₂O₄ is one of the most important materials. Small particles of the active materials facilitate high-rate capability due to large surface to mass ratio and small diffusion path length. The present work involves the synthesis of submicron size particles of LiMn₂O₄ in a quaternary microemulsion medium. The precursor obtained from the reaction is heated at different temperatures in the range from 400 to 900 °C. The samples heated at 800 and 900 °C are found to possess pure spinel phase with particle size <200 nm, as evidenced from XRD, SEM, and TEM studies. The electrochemical characterization studies provide discharge capacity values of about 100 mAh g⁻¹ at C/5 rate, and there is a moderate decrease in capacity by increasing the rate of charge–discharge cycling. Studies also include charge–discharge cycling and ac impedance studies in temperature range from −10 to 40 °C. Impedance data are analyzed with the help of an equivalent circuit and a nonlinear least squares fitting program. From temperature dependence of charge-transfer resistance, a value of 0.62 eV is obtained for the activation energy of Mn³⁺/Mn⁴⁺ redox process, which accompanies the intercalation/deintercalation of the Li⁺ ion in LiMn₂O₄.     

A novel method to fabricate lithium-ion polymer batteries based on LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>/NG electrodes

A novel method to fabricate lithium-ion polymer batteries (LiPBs) has been developed. The LiPBs was fabricated without microporous polyolefin separators, taking spinel lithium manganese oxide (LiMn₂O₄) and natural graphite (NG) as the electrodes. The thicknesses of the cathodes and the anodes are 190 and 110 μm, respectively. The NG anode was coated with a microporous composite polymer film (20 μm thick) which composed of polymer and ultrafine particles. The coating process was effective and simple to be used in practical application, and ensured the composite polymer film to act as a good separator in the LiPB. The LiPBs assembled with the coated NG anodes and pristine LiMn₂O₄ cathodes presented better electrochemical performances than liquid lithium-ion battery counterparts, proving that the microporous composite polymer film can improve the performance of the coated NG anode. In this paper, the spinel LiMn₂O₄/(coated)NG-based LiPBs exhibited high rate capability, compliant temperature reliability, and significantly, excellent cycling performance under the elevated temperature (55°C).     

Modeling the active centers of V<Subscript>2</Subscript>O<Subscript>5</Subscript>/SiO<Subscript>2</Subscript> and V<Subscript>2</Subscript>O<Subscript>5</Subscript>/TiO<Subscript>2</Subscript> supported catalysts. DFT theoretical analysis of optical properties

Within the framework of the density functional theory (DFT), the electronic structure of monooxodioxovanadium functional groups in tetrahedral coordination, which model the active centers (ACs) of fine supported catalysts V₂O₅/SiO₂ and V₂O₅/TiO₂, has been analyzed. The optimal structures of three ACs as possible models of monomeric and polymeric oxovanadium forms on the carriers with low vanadium content were determined. The modified DFT method involving the time dependence of Kohn-Sham equation (TDDFT) was used for the adopted AC models to calculate the energies of the excited states, and optical spectra of the absorption in 25000–60000 cm^?1 region were reconstructed on their base. The spectrum in this region is due to O → V charge transfer. The features of electronic spectra with the charge transfer for V₂O₅/SiO₂ and V₂O₅/TiO₂ catalysts and the vibrational spectra of three AC models corresponding to the monomeric and dimeric oxovanadium forms of the supported catalysts V₂O₅/SiO₂ and V₂O₅/TiO₂ were defined. The detailed interpretation of normal vibration frequencies is given. The frequencies typical of the monomeric and dimeric oxovanadium forms on the carrier surface were identified.     

Preparation of novel visible-light-driven In<Subscript>2</Subscript>O<Subscript>3</Subscript>–CaIn<Subscript>2</Subscript>O<Subscript>4</Subscript> composite photocatalyst by sol–gel method

Novel visible-light-activated In₂O₃–CaIn₂O₄ photocatalysts were developed in this paper through a sol–gel method. The photocatalytic activities of In₂O₃–CaIn₂O₄ composite photocatalysts were investigated based on the decomposition of methyl orange under visible light irradiation (λ > 400 nm). The obtained samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrum (EDS), X-ray photoelectron spectroscopy (XPS) and UV–vis diffused reflectance spectroscopy (DRS). The results revealed that the In₂O₃–CaIn₂O₄ composite samples with different In₂O₃ and CaIn₂O₄ content can be obtained by controlling the synthesis temperature, and the composite photocatalysts extended the light absorption spectrum toward the visible region. The photocatalytic tests indicated that the composite samples demonstrated high visible-light activity for decomposition of methyl orange. The significant enhancement in the In₂O₃–CaIn₂O₄ photo-activity under visible light irradiation can be ascribed to the efficient separation of photo-generated carriers in the In₂O₃ and CaIn₂O₄ coupling semiconductors.     

The effect of nanolayer AlF<Subscript>3</Subscript> coating on LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cycle life in high temperature for lithium secondary batteries

The surface of the spinel LiMn₂O₄ was coated with AlF₃ by a chemical process to improve its electrochemical performance at high temperatures. The morphology and structure of the original and AlF₃-coated LiMn₂O₄ samples were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM). All the samples exhibited a pure cubic spinel structure without any impurities in the XRD patterns. It was found that the surfaces of the original LiMn₂O₄ samples were covered with a nanolayer AlF₃ after the treatment. The charge/discharge of the materials were carried at 220 mA/g in the range of 3.0 and 4.4 V at 55°C. While the original LiMn₂O₄ showed 17.8% capacity loss in 50 cycles at 55°C, the AlF₃-coated LiMn₂O₄ (118.1 mA h/g) showed only 3.4% loss of the initial capacity (122.3 mA h/g) at 55°C. It is obvious that the improvement in cycling performance of the coated-LiMn₂O₄ electrode at 55°C is attributed to the presence of AlF₃ on the surface of LiMn₂O₄. Published in Russian in Elektrokhimiya, 2009, Vol. 45, No. 7, pp. 817–819. The article is published in the original     

Photocatalytic reduction of CO<Subscript>2</Subscript> over TiO<Subscript>2</Subscript> based catalysts

At present, carbon dioxide is considered the largest contributor among greenhouse gases. This review covers the current state of problem of carbon dioxide emissions from industrial and combustion processes, the principle of photocatalysis, existing literature related to photocatalytic CO₂ reduction over TiO₂ based catalysts and the effects of important parameters on the process performance including light wavelength and intensity, type of reductant, metal-modified surface, temperature and pressure. Presented at the 34th International Conference of the Slovak Society of Chemical Engineering, Tatranské Matliare, 21–25 May 2007.     

Quantum-chemical modelling of nanotubes of titanium silicocarbides Ti<Subscript>2</Subscript>SiC,Ti<Subscript>3</Subscript>SiC<Subscript>2</Subscript>, and Ti<Subscript>4</Subscript>SiC<Subscript>3</Subscript>

Atomic models are proposed for nanotubes of the titanium silicocarbides Ti₂SiC, Ti₃SiC₂, and Ti₄SiC₃, and their electronic structure and interatomic interactions are investigated by the density functional tight-binding method (DFTB) in comparison with the corresponding crystalline phases. Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 45, No. 2, pp. 88-92, March-April, 2009.     

Lithium AlPO<Subscript>4</Subscript> composite polymer battery with nanostructured LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathode

The borate ester plasticized AlPO₄ composite solid polymer electrolytes (SPE) have been synthesized and studied as candidates for lithium polymer battery (LPB) application. The electrochemical and thermal properties of SPE were shown to be suitable for practical LPB. Nanostructured LiMn₂O₄ with spherical particles was synthesized via ultrasonic spray pyrolysis technique and has shown a superior performance to the one prepared via conventional methods as cathode for LPB. Furthermore, the AlPO₄ addition to the polymer electrolyte has improved the polymer battery performance. Based on the AC impedance spectroscopy data, the performance improvement was suggested as being due to the cathode/polymer electrolyte interface stabilization in the presence of AlPO₄. The Li/composite polymer electrolyte/nanostructured LiMn₂O₄ electrochemical cell showed stable cyclability during the various current density tests, and its performance was found to be quite acceptable for practical utilities at ambient temperature and showed remarkable improvements at 60 °C compared with the solid state reaction counterpart.     

Effect of PEG with different <Emphasis Type="Italic">M</Emphasis><Subscript>W</Subscript> as template direction reagent on preparation of porous TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> with assistance of supercritical CO<Subscript>2</Subscript>

Titania–silica composite have been prepared using polyethylene glycol (PEG) with different molecular weights (M _w), PEG20000, PEG10000, and PEG2000, as template in supercritical carbon dioxide (SC CO₂). The composite precursors were dissolved in SC CO₂ and impregnated into PEG templates using SC CO₂ as swelling agent and carrier. After removing the template by calcination at suitable temperature, the titania–silica composite were obtained. The composite were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and nitrogen sorption–desorption experiment. Photocatalytic activity of the samples has been investigated by photodegradation of methyl orange. Results indicate that there are many Si–O–Ti linkages in the TiO₂/SiO₂ composite; the PEG template has a significant influence on the structure of TiO₂/SiO₂. In addition, the TiO₂/SiO₂ prepared with PEG10000 exhibited high photocatalytic efficiency. So this work supplies a clue to control and obtain the TiO₂/SiO₂ composite with different photocatalytic reactivity with the aid of suitable PEG template in supercritical CO₂.     

Ionic conduction of a high-temperature modification of Lu<Subscript>2</Subscript>Ti<Subscript>2</Subscript>O<Subscript>7</Subscript>

A nanoceramic product of the composition Lu₂Ti₂O₇ is synthesized by a coprecipitation method with a subsequent sublimation drying and an annealing at 650–1650°C. The conduction of Lu₂Ti₂O₇ synthesized at 1650°C is ionic (10^–3 S cm^–1 at 800°C). Thus, a new material with a high ionic conduction has been discovered. The ordering in Lu₂Ti₂O₇ is studied by methods of RFA, RSA, IK spectroscopy, electron microscopy, and impedance spectroscopy. The existence of a low-temperature phase transition fluorite-pyrochlore at 800°C and a high-temperature conversion order-disorder at 1650°C are established.Translated from Elektrokhimiya, Vol. 41, No. 3, 2005, pp. 298–303.Original Russian Text Copyright © 2005 by Shlyakhtina, Ukshe, Shcherbakova.     

Facile preparation and electrochemical properties of large-scale Li<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>V<Subscript>3</Subscript>O<Subscript>8</Subscript> nanobelts

Large-scale Li_1+x V₃O₈ nanobelts were successfully fabricated using filter paper as deposition substrate through a simple surface sol–gel method. The nanobelts were as long as tens of micrometers with widths of 0.4–1.0 μm and thickness of 50–100 nm. The nanobelts were characterized by X-ray diffration (XRD), Fourier infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM). The formation mechanism of the nanobelts was investigated, showing that the morphology of the nanobelts is mainly determined by the calcination temperature. Electrochemical properties of the Li_1+x V₃O₈ nanobelts were characterized by charge–discharge experiments, and the results demonstrate that the Li_1+x V₃O₈ nanobelts exhibit a high discharge capacity (278 mAh g⁻¹) and excellent cycling stability.