Thermal and photochemical stability of poly(vinyl alcohol)/modified lignin blends

A kraft lignin derivative (KLD) obtained by reaction with p-aminobenzoic acid/phthalic anhydride was blended with poly(vinyl alcohol) (PVA) by solution casting from DMSO. PVA and PVA/KLD films were exposed to ultraviolet radiation (24, 48, and 96 h) and analyzed by thermogravimetry (TG), differential scanning calorimetry (DSC), infrared spectroscopy (FTIR), hydrogen nuclear magnetic resonance (¹H NMR) spectroscopy, and scanning electron microscopy (SEM). PVA films show a loss of thermal stability due to irradiation. PVA/KLD reveals greater thermal stability than PVA and an increase in thermal stability after irradiation. These results suggest that the incorporation of KLD into PVA provides a gain in thermal and photochemical stability. FTIR, ¹H NMR, DSC, and TG results obtained for the blends suggest that intermolecular interactions between PVA and KLD chains are present. SEM micrographs revealed blend miscibility for a KLD blend content of up to 15 wt%, as observed at magnification of 1000 times.     

Photochemical stability of poly(vinyl alcohol) in the presence of collagen

The photochemical stability of poly(vinyl alcohol) (PVA) in the presence of 1%, 3% and 5% of collagen has been studied by Fourier Transform Infrared (FTIR) Spectroscopy, UV-vis spectroscopy, and Differential Scanning Calorimetry (DSC). PVA samples containing 1%, 3% and 5% of collagen were irradiated with UV light wavelength λ = 254 nm in air.The results have shown that PVA in the presence of 1%, 3% and 5% of collagen is less stable under UV radiation than pure PVA. A small amount of collagen in PVA enhances photooxidation in the PVA. The amount of crystallinity in PVA containing 1%, 3% and 5% of collagen decreases faster with UV irradiation time than that for pure PVA films.     

Chemical Characterization of Kraft Lignin Prepared from Mixed Hardwoods

Chemical characterization of kraft lignin (KL) from mixed hardwoods (Acacia spp. from Vietnam and mixed hardwoods (mainly Quercus spp.) from Korea) was conducted for its future applications. To compare the structural changes that occurred in KL, two milled wood lignins (MWLs) were prepared from the same hardwood samples used in the production of KL. Elemental analysis showed that the MWL from acacia (MWL-aca) and mixed hardwood (MWL-mhw) had almost similar carbon content, methoxyl content, and C₉ formula. KL had high carbon content but low oxygen and methoxyl contents compared to MWLs. The C₉ formula of KL was determined to be C₉H_7.29O_2.26N_0.07S_0.12(OCH₃)_1.24. The M_w of KL and MWLs was about 3000 Da and 12,000–13,000 Da, respectively. The structural features of KL and MWLs were investigated by Fourier transform infrared spectroscopy (FT-IR) and nuclear magnetic resonance spectrometry (¹H, ¹³C NMR). The analyses indicated that KL underwent severe structural modifications, such as γ-carbon cleavage, demethylation, and polycondensation reactions during kraft pulping, which resulted in increased aromatic content and decreased aliphatic content. The main linkages in lignin, β-O-4 moieties, were hardly detected in the analysis as these linkages were extensively cleaved by nucleophilic attack of SH^- and OH^- during pulping.     

Spectroscopic and Discharge Studies on Graphene Oxide Doped PVA/PVP Blend Nanocomposite Polymer Films

Graphene oxide (GO) nanoparticles were synthesized by modified Hummers method. The synthesized GO nanoparticles were incorporated in polyvinyl alcohol/polyvinyl pyrrolidone (PVA/PVP) blend polymers for the preparation of nanocomposite polymer films by solution cast technique. Different characterizations such as XRD, UV–Vis and FTIR were carried-out on to the prepared nanocomposite polymer films. The thermal analysis of the films was studied by DSC. The morphology of PVA/PVP:GO polymer films confirms GO was exfoliated within the PVA/PVP matrix and also reveals the heterogeneous phase of nanocomposite polymer electrolyte systems. From the conductivity studies the highest conductivity of PVA/PVP: GO (0.45: 0.3) was found to be 8.05 × 10^–4 S/cm at room temperature. Solid state battery has been fabricated with the configuration of Mg⁺/(PVA/PVP:GO)/(I₂ + C + electrolyte) and its cell parameters were calculated for a constant load of 100 kΩ.     

尿素/乙醇胺复配增塑聚乙烯醇性能的研究

采用尿素/乙醇胺为复合增塑剂,利用流延法制备了增塑改性的PVA膜.通过FTIR法研究了尿素/乙醇胺复合体系与PVA的相互作用,采用XRD、DSC考察了增塑改性PVA膜的结晶性能和热性能.研究结果表明,乙醇胺作为尿素的良溶剂,能有效抑制尿素从PVA基体中析出.由尿素、乙醇胺组成的复合增塑剂能破坏PVA分子中的氢键作用、降低PVA的结晶度和熔点,对PVA的增塑作用显著.增塑改性后的PVA膜在水中的溶胀率(DS)下降,溶失率(S)增加.力学性能测试表明增塑改性后的PVA膜拉伸强度(TS)降低,断裂伸长率(E%)提高.含30phr尿素/乙醇胺的PVA膜的拉伸强度、断裂伸长率分别为23.89MPa和542.88%.     

Effect of electron beam irradiation on the structural properties of poly(vinyl alcohol) formulations with triphenyl tetrazolium chloride dye (TTC)

Films of poly(vinyl alcohol) (PVA) composites with triphenyl tetrazolium chloride (TTC) dye were prepared and exposed to various radiation doses delivered by accelerated electrons. The results showed that at a low dose of 50 kGy, the colour difference (ΔE^*) of PVA/TTC films was increased by ∼10 times of the initial value. However, the change in colour differences did not go systematically with increasing the TTC content, in which the composite with 1.5 wt% displayed higher value than that with 3.5 wt%. The differential scanning calorimetry (DSC) showed that the presence of the TTC dye caused a depression in the melting point (T_m) and heat of fusion (ΔH_f) of the PVA bulk polymer. However, the thermogravimetric analysis (TGA) showed that the presence of the TTC dye improved the thermal stability of PVA. Also, the tensile strength at break of PVA/TTC composites was improved after electron beam irradiation.     

Structural features and thermal degradation properties of various lignin macromolecules obtained from poplar wood (Populus albaglandulosa)

Four different lignins obtained from poplar wood (milled wood lignin: ML, organosolv lignin: OL, ionic liquid lignin: IL and Klason lignin: KL) were subjected to several types of chemical/thermal analyses to compare their structural features and thermal decomposition properties. The ML, OL, IL and KL yield from poplar wood was 5.5, 3.9, 5.8, 19.5 wt%, respectively. Functional group analysis revealed that during the OL and KL extraction processes, the condensation reaction involved with phenolic hydroxyl groups of lignins significantly prevailed, which led to a highly condensed OL and KL structure. Thermogravimetric analysis (TGA) results showed that OL and KL thermal stability was much higher than that of ML and IL. The derivatization followed by reductive cleavage (DFRC) data showed that the thermal stability was highly associated with the frequency of arylglycerol-β-aryl ether (β-O-4) linkages in the lignin polymers. Pyrolysis-GC/MS (Py-GC/MS) analysis confirmed that acetic acid and several types of phenolic compounds were the main lignin pyrolysis products. The maximum sum of ML (13.8 wt%), OL (9.9 wt%) and IL (11.8 wt%) pyrolysis products was obtained at the pyrolysis temperature of 600 °C, whereas KL (1.6 wt%) was significantly lower due to its high thermal stability and condensation degree. The S- and G-type pyrolysis products (S/G) ratio varied from 1.61 to 1.93 for ML, 2.28 to 5.28 for OL, 2.06 to 2.86 for IL and 1.40 to 2.20 for KL, depending on the pyrolysis temperature, which ranged between 400 °C and 700 °C.     

Preparation of hydrogel from green polymer

A new method was used for the production of hydrogels from green polymer with a higher swelling ratio. These hydrogels were synthesized first by graft copolymerization between acrylamide (AM) and poly(vinyl alcohol) (PVA) with alkaline or kraft lignin (AM‐PVA‐g‐lignin) and then by mixing with acrylamide monomer. The kraft and alkaline lignins were isolated from pulping liquor and characterized using UV and FT‐IR spectroscopy, and the formed hydrogels were characterized using FT‐IR spectroscopy and scanning electron microscopy (SEM). Compared with kraft lignin hydrogel, the alkaline lignin hydrogel had very high swelling ratios and slower water uptake and deswelling rates attributed to its compatible network structure. The hydrogels formed were used also to study the influence of sodium chloride on the absorption capacity at room temperature and swelling ratios at different temperatures. Copyright © 2004 John Wiley & Sons, Ltd.     

Preparation and characterization of pva based solid polymer electrolytes for electrochemical cell applications

Solid polymer electrolyte films containing poly(vinyl alcohol) (PVA) and magnesium nitrate (Mg(NO3)2) were prepared by solution casting technique and characterized by using XRD, FTIR, DSC and AC impedance spectroscopic analysis. The amorphous nature of the polymer electrolyte films has been confirmed by XRD. The complex formation between PVA and Mg salt has been confirmed by FTIR. The glass transition temperature decreases with increasing the Mg salt concentration. The AC impedance studies are performed to evaluate the ionic conductivity of the polymer electrolyte films in the range of 303 383 K, and the temperature dependence seems to obey the Arrhenius behavior. Transport number measurements show that the charge transport is mainly due to ions. Electrochemical cell of configuration Mg/(PVA + Mg(NO3)2) (70:30)/(I2 + C + electrolyte) has been fabricated. The discharge characteristics of the cell were studied for a constant load of 100 kΩ.     

Kinetic study of the thermal decomposition of poly(vinyl alcohol)/kraft lignin derivative blends

A kraft lignin derivative (KLD) obtained by reaction with p-aminobenzoic acid/phthalic anhydride, was blended with poly(vinyl alcohol) (PVA) by solution casting from DMSO. PVA and PVA/KLD films were exposed to ultraviolet radiation (Hg lamp, 96 h) and analyzed by thermogravimetry (TG) in inert and oxidative atmosphere. Typical multi-step decomposition profiles were obtained. The apparent activation energy (E_a) of the thermal degradation of the samples was computed by the Vyazovkin method. The KLD degradation presented only small intervals of decomposition degree with constant E_a values. PVA and blends showed intervals of up to 50% in decomposition degree with nearly constant E_a, and smaller intervals in which E_a varies drastically. The influences of samples irradiation and of surrounding gas in TG analysis on E_a are also shown.     

Thermal and photochemical effects on the structure,morphology, thermal and optical properties of PVA/Ni0.04Zn0.96O and PVA/Fe0.03Zn0.97O nanocomposite films

Ni_0.04Zn_0.96O and Fe_0.03Zn_0.97O with average diameter of 23 and 19 nm, respectively, have been synthesized by a modified sol–gel method to be used in the preparation of (100 − x)/x poly(vinyl alcohol)/oxide nanocomposite films, with x = 0, 1, 3 and 5 (in wt.%). A 125 W-Hg vapor lamp with emission above 254 nmwas used to irradiate PVA/Ni_0.04Zn_0.96O and PVA/Fe_0.03Zn_0.97O films. The effect on their structural, thermal, morphological and optical properties was studied by TG, DSC, DRX, AFM, UV–vis and PL spectrophotometry. The Ni_0.04Zn_0.96O addition on PVA films decreases the thermal stability of the polymer in inert and in oxidative atmosphere. In contrast, the Fe_0.03Zn_0.97O presence in the PVA films seems to increase the thermal stability of the polymer. The characteristic peak of the crystalline phase of PVA and wurtzite phase of the zinc oxide were identified through X-ray diffraction in both films. The crystallinity of the PVA film increases with UV irradiation and with the presence of Ni_0.04Zn_0.96O and Fe_0.03Zn_0.97O. The roughness of the PVA film was not modified by the addition of the doped oxides; however, it increases after UV irradiation, more significantly in the films containing the oxides. The PVA film exhibits absorption around 280 nm characteristic of π–π^∗ transitions related to carbonyl groups from residuals acetate, while the 95/05 PVA/Ni_0.04Zn_0.96O and 95/05 PVA/Fe_0.03Zn_0.97O nanocomposite films show absorption at the visible region which is characteristics of the band gap reduction of the doped oxides. The photoluminescence of PVA was modified by the presence of the oxides in the film. These nanocomposite films are interesting due to their thermal, mechanical (flexible) properties and low cost of production. In addition they are also able to exhibit peculiar optical properties showing potential to be used in photonic devices, gas sensors and organic solar cell applications.     

Fabrication and characterization of boric acid-crosslinked ethyl cellulose and polyvinyl alcohol films as potential drug release systems for topical drug delivery

In this study, boric acid (BA) is employed as a crosslinking agent to improve the characteristics of two commonly used polymeric films, ethyl cellulose (EC) and polyvinyl alcohol (PVA), for topical drug delivery applications. The developed films are characterized by FTIR spectroscopy and SEM analysis. The results show that the surfaces of the prepared films are even and transparent, except for the BA-modified EC sample. The initial cumulative release for erythromycin (EM) is found to be 0.30 and 0.36 mg/mL for EC and PVA films, which drops to 0.25 and 0.20 mg/mL after BA crosslinking, respectively, after 1 h at 25 °C. Further, the developed formulations are stable for 75 days. Also, the antibacterial activity of the developed formulations is investigated against S. aureus (ATCC® 25923™ and ATCC® 29213™). The obtained data confirm that the application of BA as the crosslinking agent extends the release of EM from EC and PVA polymeric films. The findings of this study suggest that BA-crosslinked EC and PVA films are promising carriers for controlled topical drug delivery applications.     

Polyaniline/lignin blends: FTIR, MEV and electrochemical characterization

Blends of polyaniline (emeraldine base) and Eucalyptus grandis kraft lignin were prepared by casting method. The maximum amount of lignin that could be used for blending was 36% (w/w); beyond that, fractile films were produced. The IR spectra of the blends indicated that interactions occurred between polyaniline and lignin. Cyclic voltammetry measurements showed peaks that were readily attributed to the oxidation/reduction of polyaniline and a new oxi-reduction peak due to oxidation/reduction of sites created during interaction of two polymers. Scanning electronic microscopy showed that all blends were homogeneous.     

Preparation and Characterization of Blend Films of Poly(Vinyl Alcohol) and Sodium Alginate

Blend films of poly(vinyl alcohol) (PVA) and sodium alginate (NaAlg) were prepared by casting from aqueous solutions. This blend films were characterized by tensile strength test, Fourier transform infrared spectroscopy (FT‐IR), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The miscibility in the blends of PVA and NaAlg was established on the basis of the thermal analysis results. DSC showed that the blends possessed single, composition‐dependent glass transition temperatures (T_gs), indicating that the blends are miscible. FT‐IR studies indicate that there is the intermolecular hydrogen bonding interactions, i.e. –OH…^?OOC– in PVA/NaAlg blends. The blend films also exhibited the higher thermal stability and their mechanical properties improved compared to those of homopolymers.     

Effect of Lignin Structure Characteristics on the Performance of Lignin Based Phenol Formaldehyde Adhesives

As the second most abundant biopolymer, lignin remains underutilized in various industrial applications. Various forms of lignin generated from different methods affect its physical and chemical properties to a certain extent. To promote the broader commercial utilization of currently available industrial lignins, lignin sulfonate (SL), kraft lignin (KL), and organosolv lignin (OL) are utilized to partially replace phenol in the synthesis of phenol formaldehyde (PF) adhesives. The impact of lignin production process on the effectiveness of lignin-based phenolic (LPF) adhesives is examined based on the structural analysis of the selected industrial lignin. The results show that OL has more phenolic hydroxyl groups, lower molecular weight, and greater number of reactive sites than the other two types of lignins. The maximum replacement rate of phenol by OL reaches 70% w/w, resulting in organosolv lignin phenolic (OLPF) adhesives with a viscosity of 960 mPa·s, a minimal free formaldehyde content of 0.157%, and a shear strength of 1.84 MPa. It exhibits better performance compared with the other two types of lignin-based adhesives and meets the requirements of national standards.     

Fabrication and characterization of poly(vinyl alcohol)/chitosan hydrogel thin films via UV irradiation

A series of poly(vinyl alcohol)/chitosan (PVA/CTS) hydrogel thin films were prepared via ultraviolet (UV) irradiation, with acrylic acid (AA) monomer added as a crosslinker without the addition of any other photo-initiator. The swelling behaviors, intermolecular chemical bonds, molecular structures, thermal behaviors, degrees of crystallinity, morphologies of the surfaces and internal structure, and their relationship to the AA content were characterized using Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). Poly(acrylic acid) (PAA) and its chemical crosslinks formed in hydrogel films via free-radical reactions were confirmed using FTIR and DSC analyses. The XRD patterns indicated that the degree of crystallinity of the hydrogel films decreased as the PAA content was increased. SEM micrographs showed that a uniform interconnected pore structure was formed through the entire hydrogel structure, and a gradient in the crosslinking density through the film thickness was observed to result from extended irradiation times. The swelling behaviors revealed that the formation of PAA and its crosslinking in the hydrogel thin films improved the pH stability and controlled the degree of swelling while retaining a high swelling rate. The successful formation of chemical crosslinking without any specific photo-initiator improves the natural characteristics of CTS and PVA and imparts the resulting PVA/CTS hydrogel thin films with properties that make them very promising in biomedical applications.