Strain accumulation in InAs/In<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Ga<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>As quantum dots

The effect of strain accumulation in the InAs/In _x Ga_1−x As quantum dots (QDs) system was studied in this work. We found strain in the In _x Ga_1−x As layer with accumulation in the QD layer. This effect resulted in a dramatic reduction of growth-mode transition thickness of the QD layer. For InAs/In_0.25Ga_0.75As QDs, critical thickness is measured to be as low as 1.08 ML. The experimental results in this work highlight the importance of strain accumulation in the design and fabrication of QD-based devices with metamorphic buffer layer involved.     

Strain accumulation in InAs/In<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Ga<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>As quantum dots

The effect of strain accumulation in the InAs/In _x Ga_1−x As quantum dots (QDs) system was studied in this work. It was found that strain in the In _x Ga_1−x As layer accumulation in the QD layer. This effect resulted in a dramatic reduction of growth mode transition thickness of the QD layer. For InAs/In_0.25Ga_0.75As QDs, critical thickness is measured to be as low as 1.08 ML. The experimental results in this work highlight the importance of strain accumulation in the design and fabrication of QD-based devices with metamorphic buffer layer involved.     

Reasons of emission inhomogeneity in InAs quantum dot structures

The photoluminescence (PL) inhomogeneity has been studied in InAs quantum dots (QDs) embedded in the symmetric In_0.15Ga_0.85As/GaAs quantum wells (QWs) with QDs grown at different temperatures. It was shown that three reasons are responsible for the emission inhomogeneity in studied QD structures: (i) the high concentration of nonradiative recombination centers in the capping In_0.15Ga_0.85As layer at low QD growth temperatures, (ii) the QD density and size distributions for the structure with QD grown at 510 ^°C, (iii) the high concentration of nonradiative recombination centers in the GaAs barrier at higher QD growth temperatures.     

Influence of stoichiometry on the luminescent properties of InAs quantum dots grown on a heterostructure

We report photoluminescence (PL) spectra of InP/In_xGa_1-xAs/InAs/InP dot-in-a-well structures grown by MOVPE, with different compositions of the ternary layer. Measurements with atomic force microscopy showed that the largest quantum dot (QD) height is obtained when the InAs QDs are grown on the In_xGa_1-xAs layer with a mismatch of 1000 ppm, and the height decreases as the mismatch departs from this value. PL spectra of the QDs showed an asymmetric band, which involves transitions between dot energy levels and can be deconvoluted into two peaks. The highest energy PL peak of this band was observed for the sample with the QDs grown on top of the lattice-matched In_xGa_1-xAs layer and it shifted to lower energies for strained samples as the degree of mismatch increased. Theoretical calculations of the energy levels of the entire structure were used to interpret the obtained PL spectra and determine the possible detection tunability range.     

Emission and elastic strain in InAs dot-in-a well InGaAs/GaAs structures

The paper presents the photoluminescence (PL) study of InAs quantum dots (QDs) embedded in the asymmetric GaAs/In_xGa_1?xAs/In_0.15Ga_0.85As/GaAs quantum wells (QWs) with the different compositions of capping In_xGa_1?xAs layers. The composition of the buffer In_0.15Ga_0.85As layer was the same in all studied QD structures, but the In content (parameter x) in the capping In_xGa_1?xAs layers varied within the range 0.10–0.25. The In concentration (x) increase in the In_xGa_1?xAs capping layers is accompanied by the variation non-monotonously of InAs QD emission: PL intensity and peak positions. To understand the reasons of PL variation, the PL temperature dependences and X ray diffraction (XRD) have been investigated. It was revealed that the level of elastic deformation (elastic strain) and the Ga/In interdiffusion at the In_xGa_1?xAs/InAs QD interface are characterized by the non-monotonous dependences versus parameter x. The physical reasons for the non-monotonous variation of the elastic strains and PL parameters in studied QD structures have been discussed.     

Exciton capture and thermal escape in InAs dot-in-a-well laser structures

The photoluminescence (PL), its temperature and power dependences have been studied in InAs quantum dots (QDs) embedded in asymmetric In_xGa_1?y As/GaAs quantum wells (QWs) with variable In_xGa_1?x As compositions in the capping layer. Three stages for thermally activated decay of QD PL intensity have been revealed. A set of rate equations for exciton dynamics (relaxation into QWs and QDs, and thermal escape) are solved to analyze the mechanism of PL thermal decay. The variety of PL intensities and peak positions, as well as the activation energies of PL intensity decay in DWELL structures with different compositions of a capping layer are discussed.     

InAs/AlAs quantum dots with InGaAs insertion layer: dependence of the indium composition and the thickness

We have systematically studied the effect of an In_xGa_1−xAs insertion layer (IL) on the optical and structural properties of InAs quantum dot (QD) structures. A high density of 9.6×10¹⁰ cm⁻² of InAs QDs with an In_0.3Ga_0.7As IL has been achieved on a GaAs (1 0 0) substrate by metal organic chemical vapor deposition. A photoluminescence line width of 25 meV from these QDs has been obtained. We attribute the high density and high uniformity of these QDs to the use of the IL. Our results show that the InGaAs IL is useful for obtaining high-quality InAs QD structures for devices with a 1.3 μm operation.     

不同组分InxGa1-xAs(0≤x≤0.3)覆盖层对自组织InAs量子点的影响

研究了不同In组分的In_xGa_1-xAs(0≤x≤0.3)覆盖层对自组织InAs量子点的结构及发光特性的影响.透射电子显微镜和原子力显微镜表明,InAs量子点在InGaAs做盖层时所受应力较GaAs盖层时有所减小,并且x＝0.3时,InGaAs在InAs量子点上继续成岛.随x值的增大,量子点的光荧光峰红移,但随温度的变化发光峰峰位变化不明显.理论分析表明InAs量子点所受应力及其均匀性的变化分别是导致上述现象的主要原因. 关键词： 量子点 盖层 应力 红移     

Features of the formation of Mn doped InAs/GaAs quantum dots by vapor phase epitaxy

A self-organized InAs/GaAs quantum dot (QD) array is doped with Mn. The effect of the Mn concentration on the morphology and QD luminescence properties is investigated. It is found that Mn deltadoping of the GaAs buffer layer before QD growth with a layer concentration of 10¹⁴ cm^?2 leads to the formation of an array of large QDs with variable composition In _x Ga_{1 ? x} As. The effect is explained within a model of In and Ga atom interdiffusion.     

Competition in the carrier capture between InGaAs/AlGaAs quantum dots and deep point defects

The presence of an extrinsic photoluminescence (PL) band peaked at 1.356 eV at low temperature is observed, on a large number of self-assembled InAs and In_0.5Ga_0.5As quantum dot (QD) structures, when exciting just below the GaAs absorption edge. A detailed optical characterization allows us to attribute the 1.356 eV PL band to the radiative transition between the conduction band and the doubly ionized Cu _Ga acceptor in GaAs. A striking common feature is observed in all investigated samples, namely a resonant quenching of the QD-PL when exciting on the excited level of this deep defect. Moreover, the photoluminescence excitation (PLE) spectrum of the 1.356 eV emission turns out to be almost specular to the QD PLE. This correlation between the PL efficiency of the QDs and the Cu centers evidences a competition in the carrier capture arising from a resonant coupling between the excited level of the defect and the electronic states of the wetting layer on which the QDs nucleate. The estimated Cu concentration is compatible with a contamination during the epitaxial growth. Received 13 November 2001 / Received in final form 28 May 2002 Published online 19 July 2002     

Confinement-enhanced dots-in-a-well QDIPs with operating temperature over 200 K

LWIR InAs/Al_0.3Ga_0.7As/In_0.15Ga_0.85As confinement-enhanced DWELL (CE-DWELL) QDIPs with operation temperatures higher than 200 K are reported. A thin Al_0.3Ga_0.7As barrier layer was inserted above the InAs QDs to improve the confinement of QD states in the In_0.15Ga_0.85As DWELL structure and the device performance. The better confinement of the electronic states increases the oscillator strength of the infrared absorption. The higher excited state energy also improves the escape probability of the photoelectrons. Compared with the conventional DWELL QDIPs, the quantum efficiency increases for more than 20 times and the detectivity is an order of magnitude higher at 77 K. With better device parameters of CE-DWELL, it is possible to achieve high quantum efficiency, high operating temperature and long wavelength detection at the same time.     

The emission wavelength tuning of InAs/InP quantum dots with thin GaAs, InGaAs, InP capping layers by MOCVD

InAs quantum dots (QDs) were grown on InP substrates by metalorganic chemical vapor deposition. The width and height of the dots were 50 and 5.8 nm, respectively on the average and an areal density of 3.0×10¹⁰ cm⁻² was observed by atomic force microscopy before the capping process. The influences of GaAs, In_0.53Ga_0.47As, and InP capping layers (5–10 ML thickness) on the InAs/InP QDs were studied. Insertion of a thin GaAs capping layer on the QDs led to a blue shift of up to 146 meV of the photoluminescence (PL) peak and an InGaAs capping layer on the QDs led to a red shift of 64 meV relative to the case when a conventional InP capping layer was used. We were able to tune the emission wavelength of the InAs QDs from 1.43 to 1.89 μm by using the GaAs and InGaAs capping layers. In addition, the full-width at half-maximum of the PL peak decreased from 79 to 26 meV by inserting a 7.5 ML GaAs layer. It is believed that this technique is useful in tailoring the optical properties of the InAs QDs at mid-infrared regime.     

Optical transitions and carrier dynamics in self-organized InAs quantum dots grown on In0.52Al0.48As/InP(0 0 1)

Optical transitions in self-organized InAs quantum dots (QDs) grown on In_0.52Al_0.48As layer lattice matched to InP(0 0 1) substrate, have been studied by continuous wave (cw) photoluminescence (PL) and time-resolved PL. The dependence of the PL transition on excitation power and photoluminescence excitation measurements clearly shows that the multi-component cw-PL spectrum is related to emission coming from ground and related excited states of QDs with heights varying by monolayer fluctuations. While decay times measured by time-resolved PL are in the nanosecond range for the ground states, shorter decay times related to relaxation of carriers down directly to the ground state are determined for the excited states.     

Emission and strain in InGaAs/GaAs quantum wells with InAs quantum dots obtained at different temperatures

The photoluminescence (PL), its temperature dependence and X ray diffraction (XRD) have been studied in the symmetric In_0.15Ga_0.85As/GaAs quantum wells (QWs) with embedded InAs quantum dots (QDs), obtained with the variation of QD growth temperatures (470–535 °C). The increase of QD growth temperatures is accompanied by the enlargement of QD lateral sizes (from 12 up to 28 nm) and by the shift non monotonously of PL peak positions. The fitting procedure has been applied for the analysis of the temperature dependence of PL peaks. The obtained fitting parameters testify that in studied QD structures the process of In/Ga interdiffusion between QDs and capping/buffer layers takes place partially. However this process cannot explain the difference in PL peak positions.     

Improvement of the optical property and uniformity of self-assembled InAs/InGaAs quantum dots by layer-by-layer temperature and substrate rotation

The influence of layer-by-layer temperature and substrate rotation on the optical property and uniformity of self-assembled InAs/In_0.2Ga_0.8As/GaAs quantum dots (QDs) gown with an As₂ source was investigated. An improvement in the optical property of QDs was obtained by the precise control and optimization of growth temperature utilized for each layer, i.e., InAs QDs, InGaAs quantum wells, GaAs barriers and AlGaAs layers, respectively. By using a substrate rotation, the QD density increased from ∼1.4×10¹⁰ to ∼3.2×10¹⁰ cm⁻² and its size also slightly increased, indicating a good quality of QDs. It is found that the use of an appropriate substrate rotation during growth improves the room-temperature (RT) optical property and uniformity of QDs across the wafer. For the QD sample with a substrate rotation of 6 rpm, the RT photoluminescence (PL) intensity is much higher and the standard deviation of RT-PL full-width at half-maximum is decreased by 35% compared to that grown without substrate rotation.     

Photoluminescence scanning on InAs/InGaAs quantum dot structures

The photoluminescence spectra of InAs quantum dots (QDs) embedded into four types of In_xGa_1−xAs/GaAs (x = 0.10, 0.15, 0.20 and 0.25) multi quantum well MBE structures have been investigated at 300 K in dependence on the QD position on the wafer. PL mapping was performed with 325 nm HeCd laser (35 mW) focused down to 200 μm (110 W/cm²) as the excitation source. The structures with x = 0.15 In/Ga composition in the In_xGa_1−xAs capping layer exhibited the maximum photoluminescence intensity. Strong inhomogeneity of the PL intensity is observed by mapping samples with the In/Ga composition of x ≥ 0.20-0.25. The reduction of the PL intensity is accompanied by a gradual “blue” shift of the luminescence maximum at 300 K as follows from the quantum dot PL mapping. The mechanism of this effect has been analyzed. PL peak shifts versus capping layer composition are discussed as well.     

Bandgap engineering of self-assembled InAs quantum dots with a thin AlAs barrier

We investigate the effects of a thin AlAs layer with different position and thickness on the optical properties of InAs quantum dots (QDs) by using transmission electron microscopy and photoluminescence (PL). The energy level shift of InAs QD samples is observed by introducing the thin AlAs layer without any significant loss of the QD qualities. The emission peak from InAs QDs directly grown on the 4 monolayer (ML) AlAs layer is blueshifted from that of reference sample by 219 meV with a little increase in FWHM from 42–47 meV for ground state. In contrast, InAs QDs grown under the 4 ML AlAs layer have PL peak a little redshifted to lower energy by 17 meV. This result is related to the interdiffusion of Al atom at the InAs QDs caused by the annealing effect during growing of InAs QDs on AlAs layer.     

Interband transitions and electronic properties of InAs/GaAs quantum dots embedded in AlxGa1−xAs/GaAs modulation-doped heterostructures

Reflection high-energy electron diffraction, atomic force microscopy, transmission electron microscopy, and double-crystal X-ray curves showed that high-quality InAs quantum dot (QD) arrays inserted into GaAs barriers were embedded in an Al_0.3Ga_0.7As/GaAs heterostructure. The temperature-dependent photoluminescence (PL) spectra of the InAs/GaAs QDs showed that the exciton peak corresponding interband transition from the ground electronic subband to the ground heavy-hole subband (E₁-HH₁) was dominantly observed and that the peak position and the full width at half maximum corresponding to the interband transitions of the PL spectrum were dependent on the temperature. The activation energy of the electrons confined in the InAs/GaAs QDs was 115 meV. The electronic subband energy and the energy wave function of the Al_0.3Ga_0.7As/GaAs heterostructures were calculated by using a self-consistent method. The electronic subband energies in the InAs/GaAs QDs were calculated by using a three-dimensional spatial plane wave method, and the value of the calculated (E₁-HH₁) transition in the InAs/GaAs QDs was in reasonable agreement with that obtained from the PL measurement.     

Photoexcited carrier dynamics in aligned InAs/GaAs quantum dots grown on strain-relaxed InGaAs layers

Carrier dynamics in aligned InAs/GaAs quantum dots (QDs) grown on cross-hatched patterns induced by metastable In_xGa_1−xAs layers have been studied by time-resolved photoluminescence. The low-temperature carrier lifetimes were found to be of the order of 100–200 ps and determined by carrier trapping and nonradiative recombination. Comparisons with control “nonaligned” InAs QDs show remarkable differences in dependence of peak PL intensities on excitation power, and in PL decay times dependences on both temperature and excitation intensities. Possible origin of traps, which determine the carrier lifetimes, is discussed.     

Tailoring of the Wave Function Overlaps and the Carrier Lifetimes in InAs/GaAs1−xSbx Type-II Quantum Dots

Effects of thermal annealing on the emission properties of type-II InAs quantum dots (QDs) covered by a thin GaAs_1−xSb_x layer are investigated by photoluminescence (PL) and time-resolved PL measurements. Apart from large blueshifts and a pronounced narrowing of the QD emission peak, the annealing induced alloy intermixing also leads to enhanced radiative recombination rates and reduced localized states in the GaAs_1−xSb_x layer. We find that the type-II QD structure can sustain thermal annealing up to 850 °C. In particular, we find that it is possible to manipulate between type-I and type-II recombinations in annealed QDs by using different excitation powers. We demonstrate that postgrowth thermal annealing can be used to tailor the band alignment, the wave function overlaps, and hence the recombination dynamics in the InAs/GaAs_1−xSb_x type-II QDs.