苄泽类非离子型表面活性剂与明胶的相互作用

采用表面张力和稳态荧光光谱法考察了具有不同疏水结构的2种苄泽类非离子型表面活性剂Brij58和Brij78与明胶之间的相互作用。结果表明,苄泽类非离子型表面活性剂与明胶之间相互作用的驱动力为疏水作用力,且两者之间的相互作用受到其疏水基团的影响,Brij78在明胶溶液中的临界聚集浓度低于Brij58体系,表明疏水链更长的Brij78与明胶之间的相互作用更强。明胶分子的内源荧光光谱强度受苄泽类非离子型表面活性剂的影响,但最大吸收峰位置未发生蓝移,Brij78/明胶体系的内源荧光强度高于Brij58/明胶体系;此外,表面活性剂浓度较低时,明胶的加入使溶液中疏水微区极性明显降低,且明胶浓度越大降低程度越大。     

非离子表面活性剂浊点的研究进展

综述了非离子表面活性剂浊点的理论模型,介绍了非离子表面活性剂的浓度与外加无机电解质、极性有机物,表面活性剂、聚合物对浊点的影响规律和机理,以及在常压下浊点高于100℃时非离子表面活性剂的浊点估测方法。     

离子液体型表面活性剂C12mimBr与普通表面活性剂混合性质的研究

研究了离子液体型表面活性剂C12mimBr与阳离子表面活性剂Gemini 12-3-12, DTAB及阴离子表面活性剂SDS复配体系的性质, 并分别采用Rubingh-Margules模型和Rubingh-正规溶液模型计算了临界胶束浓度和混合胶团组成. 研究发现, 两表面活性剂分子结构的匹配性及带电头基之间的相互作用是影响混合溶液性质的主要因素. 对于分子结构差别较大的C12mimBr与Gemini 12-3-12的混合, 其行为远远偏离理想混合性质; 对疏水链长相同仅亲水头基不同的C12mimBr与DTAB则接近于理想混合; 而对C12mimBr＋SDS的复配体系, 正、负电荷间强烈的相互吸引使得混合体系大大偏离理想行为. 计算发现, 两种理论模型得到的混合胶团组成基本一致, 但Rubingh-Margules模型预测的临界胶束浓度比Rubingh-正规溶液模型要好     

基于光纤折射率传感原理的表面活性剂临界胶束浓度测定方法

提出并研究了一种新颖的基于光纤折射率传感原理的表面活性剂临界胶束浓度(cmc)测定方法.应用此方法测定有代表性的阴离子表面活性剂十二烷基硫酸钠(SDS)与阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)在25℃下的cmc分别为8.05×10-3和9.11×10-4mol·L-1,与文献值比较,结果相当吻合.从而证实了本方法的准确性.进一步研究了各种条件对测量表面活性剂cmc的影响,结果表明温度和无机盐NaCl的加入对本方法测量的准确性影响小,证明了本方法对测试环境的要求不苛刻,适用性好.最后对本方法进行了重复性和稳定性测试,相对标准偏差(RSD)为0.17%,与预期符合,效果良好.     

表面活性剂胶束化物理化学性质研究

通过电导法考查温度和盐浓度对十二烷基硫酸钠(SDS)临界胶束浓度(CMC)的影响,研究表面活性剂形成胶束过程的物理化学性质。根据拟相分离模型求得胶束化热力学函数,并讨论体系电导活化能随温度和SDS浓度变化关系。结果表明:SDS的CMC随温度升高而增加,随氯化钠浓度增大而减小。在热力学上SDS在水溶液中形成胶束是一个自发、放热、熵增的过程;在动力学上,SDS溶液电导率与温度关系符合Arrhenius公式,通过电导活化能信息可揭示离子型表面活性剂形成胶束的机理特征。     

聚氧乙烯醚型表面活性剂的合成及表面性质

合成了一系列不同聚合度的聚壬基酚聚氧乙烯醚型非离子表面活性剂, 通过红外光谱和核磁共振等手段对其结构进行表征, 用表面张力法对合成产物的表面性能进行研究. 结果表明, 随着表面活性剂分子中亲水基团环氧乙烷(EO)片段的增加, 单体、 二聚体和三聚体的临界胶束浓度(cmc)值都逐渐增大, 当EO数目相同时, 单体、 二聚体和三聚体的cmc值依次明显降低. 二聚体与三聚体都显示出很好的表面性质, 其中三聚体的表面性质比二聚体表面性能更优. 在空气/水表面二聚体和三聚体比单体的排列更加紧密, 表现出更好的吸附和分散性能.     

非离子表面活性剂增敏三元离子缔合物光度法测定微量银

研究并建立了非离子表面活性剂聚乙二醇辛基苯基醚(Tx-100)胶束增敏离子缔合物分光光度法测定微量银的分析方法。实验结果表明,在表面活性剂存在下,方法的灵敏度比未增敏体系提高了近5倍,络合物稳定性也大大增加。方法的最佳酸度是pH=4.0,银浓度在0～0.4mg·mL-1符合比耳定律。以EDTA为掩蔽剂,只有Br-、I-、CN-、S2-有干扰。方法用于人工合成样品和显影废液中微量银的分析,准确度和精密度令人满意。     

Gemini 阴离子表面活性剂水溶液的聚集性质

合成了一种Gemini阴离子表面活性剂,测定了其临界胶束浓度cmc和cmc时的表面张力γcmc,与传统的单基表面活性剂相比,其临界胶束浓度降低了一个数量级,具有突出的降低水的表面张力的效率;研究了该种Gemini表面活性剂的浓度对于胶束聚集数的影响,结果表明,随着浓度的增加,胶束聚集数出现了一个极大值,同时观察到液晶微相的生成.     

阳、阴、非离子表面活性剂胶束对酯碱性水解的影响

应用紫外分光光度法和热动力学方法研究了芳香酸酯和正脂肪酸酯在表面活性剂ＤＴＡＢ、ＴＴＡＢ、ＣＴＡＢ、ＳＤＳ、Ｂｒｉｊ３５、ＴｒｉｔｏｎＸ－１００胶束中的碱性水解反应。阳、阴、非离子表面活性剂胶束对酯的碱性水解均有禁阻作用。讨论了胶束对酯碱性水解禁阻作用的原因。     

壬基酚聚氧乙烯醚二聚和三聚表面活性剂的合成及表面性质

合成了系列壬基酚聚氧乙烯醚二聚表面活性剂(DNP)和三聚表面活性剂(TNP), 用核磁共振、红外光谱和元素分析等手段对其结构进行了表征, 并用表面张力法和稳态荧光法对DNP和TNP的表面性能进行了研究. 结果表明, 随着氧乙烯(EO)单元数的增长, DNP和TNP的临界胶束浓度(cmc)值逐渐增大; DNP和TNP的cmc值较相应的单体壬基酚聚氧乙烯醚表面活性剂(NP)明显降低, 显示了较高的表面活性、吸附能力和润湿能力.     

Photophysical Properties of Ethidium Bromide in Low Concentration of Sodium Dodecyl Sulfate

Sodium dodecyl sulfate (SDS) is widely utilized in biomolecules separation, but high residue SDS in biomolecules samples interfere mass analysis. Ethidium bromide (EtdBr) interacts with SDS, and the formation of EtdBr‐SDS complex at low SDS concentration (0–0.1 %) results a large red shift of the n→π* transition of EtdBr from 480 nm to 530 nm. The ion pairs become non‐emissive and cause low emission intensity. While the concentration of SDS is above 0.1 %, SDS starts aggregating to form micelle. Micelle formation destabilizes the complex and the absorption maxima shift back to 513 nm while emission intensity increases. Based on the change of absorption and emission of EtdBr, a SDS concentration assay was developed. If absorption maximizes at 480 nm, the concentration of SDS of the sample is below 0.005 %. If absorption maximum is at longer wavelength than 480 nm, a second parameter, the ratio of absorbance at 513 nm and 550 nm is introduced. If the ratio is smaller than 1.5, the concentration of SDS is between 0.01–0.1 %. If the ratio is larger than 1.5, the concentration of SDS is above 0.15 %. Despite the suitable range is small, the lower limit is around the range of no mass interference.     

Effects of Cs and Na ions on the interfacial properties of dodecyl sulfate solutions

The competitive binding of counterions to anionic dodecyl sulfate ions in aqueous solutions of cesium dodecyl sulfate (CsDS) and sodium dodecyl sulfate (SDS) mixtures, which significantly influences the critical micelle concentration (cmc) and surface (or interfacial) tension of surfactant solutions, was investigated. The cmc and degree of counterion binding were obtained through electrical conductivity measurements. The curve of cmc versus the mole fraction of CsDS in the surfactant mixture was simulated by Rubingh's equations, which enabled us to estimate the interaction parameter in micelles (W _R) based on the regular solution approximation. The curve-fitting exhibited a slightly negative value (W _R=−0.1), indicating that the mixing (SDS+CsDS) enhances micelle formation owing to a greater interaction between surfactant molecules and counterions than in pure systems (SDS). On going from SDS, SDS:CsDS(75:25), SDS:CsDS(50:50), SDS:CsDS(25:75) to CsDS, interfacial tension at the hexadecane/surfactant-solution interface showed a negative deviation from the mixing rule (interaction parameter in adsorbed film W _A=−0.38), indicating the replacement of Na⁺ bound to anionic dodecyl sulfate by Cs⁺ ions owing to the stronger interaction between the Cs⁺ and the dodecyl sulfate ions. Droplet sizes of emulsion formed with hexadecane and aqueous dodecyl sulfate solutions were investigated using the light scattering spectrophotometer. The higher binding capacity of Cs⁺, having a smaller hydrated ionic size than Na⁺, also resulted in a negative deviation in emulsion droplet size in mixed systems. Received: 10 May 2000/Accepted: 11 August 2000     

Determination of the Critical Micelle Concentration of Cationic Surfactants by Capillary Electrophoresis

The determination of the critical micelle concentration (CMC) of cationic surfactants by capillary electrophoresis was demonstrated. In this study, tetradecyltrimethylammonium bromide (TTAB) and dodecyltrimethylammonium bromide (DoTAB) were selected as cationic surfactants and propazine was chosen as test solute. In the evolution of the effective electrophoretic mobility of propazine as a function of surfactant concentration, a dramatic change in slope at a particular concentration is a good indication of the CMC of this surfactant. The CMC values determined experimentally were further confirmed by a curve-fitting approach. Simulation of the electrophoretic mobility curves as a function of surfactant concentration in both micellar electrokinetic chromatography and capillary zone electrophoresis using cationic surfactants as an electrolyte modifier was performed for propazine, and the intersection of these two mobility curves allowed us to precisely predict the CMC of the surfactant. The CMC values determined for TTAB and DoTAB are 1.6 ± 0.1 and 11.0 ± 0.1 mM, respectively, in the case of an electrolytic solution consisting of 70 mM phosphate buffer at pH 6.0. Moreover, the applicability of the electroosmotic mobility as a parameter for the determination of the CMC was examined.     

A novel fused-silica capillary dropping mercury electrode with long drop-time and its application on determination of critical micelle concentration

A novel long drop time mercury electrode has been constructed from common fused-silica capillary (50 μm I.D., 360 μm E.D.). Proposed device provides reproducible mercury drops with typical lifetime 40-120 s. The electrode was used for a set of electrocapillary measurements aimed at determination of critical micelle concentration of anionic surfactants by a convection controlled drop-time technique. A critical micelle concentration of sodium dodecyl sulfate 5.6 ± 0.4 mmol L⁻¹ and 4.3 ± 0.4 mmol L⁻¹ were obtained in 1 mmol L⁻¹ and 5 mmol L⁻¹ phosphate buffer (pH 7.0), respectively. The values were comparable to those obtained from conductometric measurements under the same conditions (7.0 ± 0.1 mmol L⁻¹ and 5.2 ± 0.1 mmol L⁻¹, respectively) and the difference was explained in accordance with theory of hemi-micelle formation.     

卵清蛋白与离子型表面活性剂的相互作用

本文通过荧光光谱法、紫外-可见吸收光谱法和透射电镜并结合电导率测定分别研究了水中卵清蛋白与阴离子表面活性剂十二烷基硫酸钠（SDS）和阳离子表面活性剂十二烷基三甲基溴化铵（DTAB）和十六烷基三甲基溴化铵（CTAB）之间的相互作用。研究结果表明卵清蛋白可以增加SDS和CTAB的临界胶束浓度,但对DTAB的临界胶束浓度没有影响。阴离子表面活性剂可以使卵清蛋白构象完全伸展,而阳离子表面活性剂却不具备此种作用。表面活性剂单体与卵清蛋白的相互作用强于表面活性剂胶束与卵清蛋白的相互作用。     

Surface Properties and Etherification in Microemulsion Systems of Novel Brönsted Acid Surfactants

Novel Brönsted acid-surfactants with different alkyl chains were synthesized via a two-step process, and their surface properties were studied. The critical micelle concentration(cmc), surface tension at the cmc(γ_cmc), and ability of these compounds to lower the surface tension by 0.02 N/m(C₂₀ and pC₂₀) were investigated at 25 and 40℃. The molecular architecture of the compounds strongly influenced these physicochemical parameters. The ability of these compounds to lower surface tension was found to be good. Etherification in microemulsions formed by these surfactants as well as dodecylbenzenesulfonic acid(DBSA) was performed; surfactants 3a and 3b were found to be much more efficient than dodecylbenzenesulfonic acid(DBSA).     

可见吸收光谱线型参数分析法测定十二烷基硫酸钠临界胶束浓度

于浓度相同的结晶紫（CV）溶液中,加入不同浓度的十二烷基硫酸钠（SDS）组成一系列含有相同浓度CV和不同浓度SDS的混合溶液。在可见光区内对每一混合溶液测定其吸收值时,可见随SDS浓度的逐步递增,在CV-单聚体吸收峰的吸收值逐渐减少;而在CV-二聚体吸收峰的吸收值逐渐增加,且随CV-二聚体浓度增加而出现的CV-二聚体与CV-单聚体的吸收光谱线相互严重重叠,光谱形状也发生渐变。运用分光光度计所配备的Origin 7．5软件中储存的高斯多峰拟合法,可自动进行重叠光谱的解析和各光谱参数（包括y0,A1,A2,ω1,ω2,xc1及xc2）的拟合计算。文中还证示,每一参数与SDS浓度之间有明显的相关性,在两者之间所作的曲线上可找到明显的转折点,与转折点相对应的、在横坐标上的SDS浓度值即为SDS的临界胶束浓度（CMC）值。文中首次报道了用吸收光谱的半峰宽对SDS浓度作图所得曲线上的转折点求得SDS的CMC值。     

Intermolecular Interactions in Self-Assembly Process of Sodium Dodecyl Sulfate by Vertically Polarized Raman Spectra

Molecular self-assembly is extremely important in many fields, but the characterization of their corresponding intermolecular interactions is still lacking. The C-H stretching Raman band can reflect the hydrophobic interactions during the self-assembly process of sodium dodecyl sulfate (SDS) in aqueous solutions. However, the Raman spectra in this region are seriously overlapped by the OH stretching band of water. In this work, vertically polarized Raman spectra were used to improve the detection sensitivity of spectra of C-H region for the first time. The spectral results showed that the first critical micelle concentration and the second critical micelle concentration of SDS in water were 8.5 and 69 mmol/L, respectively, which were consistent with the results given by surface tension measurements. Because of the high sensitivity of vertically polarized Raman spectra, the critical micelle concentration of SDS in a relatively high concentration of salt solution could be obtained in our experiment. The two critical concentrations of SDS in 100 mmol/L NaCl solution were recorded to be 1.8 and 16.5 mmol/L, respectively. Through comparing the spectra and surface tension of SDS in water and in NaCl solution, the self-assembly process in bulk phase and at interface were discussed. The interactions among salt ions, SDS and water molecules were also analyzed. These results demonstrated the vertically polarized Raman spectra could be employed to study the self-assembly process of SDS in water.     

十二烷基甜菜碱/十二烷基硫酸钠复配体系的表面活性

研究了两性表面活性剂十二烷基甜菜碱（C12BE）和阴离子型表面活性剂十二烷基硫酸钠（SDS）复配体系的形成胶束能力,降低表面张力效率,降低表面张力能力三种增效作用.发现C12BE和SDS摩尔比为6 :4时增效作用最显著.并考察了盐、醇对复配体系表面活性的影响,结果表明,加盐能导致表面活性的提高,加醇的机理比较复杂,乙醇对复配体系表面活性影响不大,而正丁醇影响则比较显著.     

新型Gemini咪唑表面活性剂的合成及表面性能

以2,2-双(溴甲基)-1,3-丙二醇为连接基合成了新型的连接基为枝状的Gemini咪唑表面活性剂2,4-二(溴化-3-烷基咪唑)-1,3-丙二醇([Cn-P-Cnim]Br2,n=10,12,14).产物经核磁共振氢谱(1H NMR)、红外(IR)光谱和元素分析等进行了分析,证明所得产物即为目标产物.通过表面张力法和电导法测量其表面活性并计算胶束形成热力学参数(ΔG m—0,ΔH m—0,ΔS m—0).结果表明,25℃时3种表面活性剂均具有很高的表面活性,胶束的形成是自发的熵驱动过程.