Silica sol/Nano-Au/PVA/L-cysteine修饰金电极电致化学发光测定甲氧氯普胺的研究

在甲氧氯普胺对联吡啶钌具有较好电化学发光增敏效果的基础上,制备出Silica sol/Nano-Au/PVA/L-cysteine修饰金电极,并通过电致化学发光法,考察了联吡啶钌及联吡啶钌-甲氧氯普胺体系在此电极上的电化学及电化学发光行为。该修饰电极对联吡啶钌-甲氧氯普胺体系有良好的电致化学发光响应特性;在最优条件下,在1.0×10-7~1.0×10-4mol/L范围内甲氧氯普胺浓度与其对应的电化学发光强度值线性关系良好,检出限(S/N=3)为1.40×10-9mol/L;通过平行测定1.0×10-5mol/L甲氧氯普胺溶液8次,发光强度值相对偏差(RSD)为1.8%,样品回收率在98.3%~104.4%之间,RSD为2.3%(n=5)。     

Ru (bpy)2+3体系电化学发光法测定阿奇霉素的研究

实验发现,阿奇霉素对联吡啶钌的电致化学发光(ECL)具有显著的增强作用.据此,建立了以金电极为工作电极的测定阿奇霉素ECL分析新方法.采用了循环伏安(CV)和ECL法,研究了阿奇霉素对联吡啶钌体系的电化学行为和ECL行为的增强作用.结果表明,在最佳条件下,阿奇霉素浓度在2.0×10-4～4.0×10+7moL/L范围内...     

固定丝素蛋白膜中的联吡啶钌电化学发光行为的研究与应用

基于苯海拉明对联吡啶钌(Ru(bpy)2+3)的电化学发光的增敏作用和丝素蛋白-联吡啶钌复合膜修饰玻碳电极稳定好的特点,建立了一种以丝素蛋白多孔膜-联吡啶钌复合物修饰的玻碳电极电化学发光检测苯海拉明的新方法.结果表明,该修饰电极具有很好的电化学活性和电化学发光(ECL)响应.在最佳实验条件下,苯海拉明浓度在1.0×10-4～1.0×10-7 mol/L范围内与其相对发光强度呈良好的线性关系(r=0.9989); 检出限为2.3×10-7 mol/L(S/N=3).连续平行测定3.78×10-5 mol/L苯海拉明5次,发光强度的RSD为1.76%. 用于实际样品中苯海拉明的测定,结果满意.     

巯基乙酸修饰金电极电化学发光行为的研究及其对盐酸硫必利的测定

在裸金电极上制备了巯基乙酸自组装膜修饰电极(MA/SAMs-Au/CME)。基于盐酸硫必利对联吡啶钌在该电极上的电化学及其发光行为的强烈增敏作用,建立起一种直接测定盐酸硫必利电致化学发光新方法。在最佳实验条件下,盐酸硫必利在1.0×10-4～1.0×10-7mol/L与相对发光强度呈线性关系,其线性回归方程I(强度)=27.169×106c+140.26,r2=0.9959,检出限(S/N=3)为5.11×10-9mol/L。连续测定1.0×10-5mol/L盐酸硫必利10次,发光强度的RSD值为1.8%。对样品进行回收率试验,回收率在94.1%～104.9%之间,RSD为4.5%(n=5)。     

硅溶胶-纳米金修饰金电极电化学发光法测定苦参碱的研究

基于苦参碱对联吡啶钌电化学发光的增敏作用,利用溶胶-凝胶固定化稳定的优点和纳米金对苦参碱的电催化作用,建立了硅溶胶-纳米金修饰金电极电化学发光检测苦参碱的新方法,考察了苦参碱在该修饰电极上的电化学及其发光行为。结果表明,此修饰电极表现出很好的电化学活性和电化学发光(ECL)响应,在最佳实验条件下,苦参碱浓度在1.5×10-7～1.5×10-4mol/L范围内与相对发光强度呈线性关系(r2=0.998 4),检出限(S/N=3)为7.3×10-9mol/L。连续平行测定1.5×10-5mol/L的苦参碱溶液8次,发光强度的相对标准偏差(RSDs)为1.4%。样品回收实验得到苦参碱的加标回收率为98%～102%,RSD(n=5)为1.8%。该方法具有较高的选择性和灵敏度,样品处理简单快速,用于苦参碱栓中苦参碱的测定,结果满意。     

联吡啶钌体系电化学发光法测定苦参碱的研究

采用循环伏安(CV)法和电化学发光(ECL)法,研究了苦参碱(Matrine,MT)与联吡啶钌(Ru(bpy)23+)体系的电化学行为和电致化学发光(ECL)行为,以金电极为工作电极,建立了测定MT的ECL分析新方法。研究结果表明,在0.1 mol/LNa2HPO4-NaH2PO4缓冲溶液中,当扫描速度为0.1V/s时,该ECL的峰高与MT在1.5×10-7～1.5×10-4 mol/L范围呈线性关系(r=0.9989),检出限(S/N=3)为7.3×10-9 mol/L。平行测定1.5×10-5 mol/L的MT溶液10次,发光强度值的相对标准偏差(RSD)为4.01%。对样品进行回收率试验,加入回收率在97.1%～104.0%之间,RSD为2.86%(n=5)。该方法具有较高的选择性和灵敏度,样品处理简单快速,可用于药物中苦参碱的测定。     

纳米石墨烯修饰电极电化学发光法测定盐酸氯丙嗪的研究

基于盐酸氯丙嗪对联吡啶钌电化学发光的增敏作用,以石墨烯(Graphene)和Nafion复合膜修饰的玻碳电极(GCE)为工作电极,建立了一种直接测定盐酸氯丙嗪的电化学发光新方法。最佳实验条件下,盐酸氯丙嗪浓度在8.0×10-7~1.2×10-4mol/L范围内与其相对发光强度呈良好线性关系(r=0.998 8),且在该修饰电极上的检出限(S/N=3)为4.0×10-7mol/L。连续测定4.0×10-6mol/L盐酸氯丙嗪溶液11次,发光强度值的相对标准偏差(RSD)为1.4%,表明该修饰电极具有较好的重复性和灵敏度。盐酸氯丙嗪的加标回收率为93%~104%,RSD(n=5)为4.1%。将该方法应用于药片中盐酸氯丙嗪的检测,结果满意。     

联吡啶钌体系电化学发光法测定舒必利的研究

采用了循环伏安(CV)和电致化学发光(ECL)法,研究了舒必利增强联吡啶钌[Ru(bpy)23+]体系的电化学行为和电化学发光行为,建立了以玻碳电极为工作电极的舒必利电致化学发光分析方法。研究结果表明,在0.1mol/L的磷酸盐缓冲溶液(pH=7.5)中,扫描速度为100mV/s时,ECL的峰高与舒必利浓度在4.0×10-7～1.0×10-4mol/L范围内呈线性关系,相关系数r=0.9957,检出限(S/N=3)为5.3×10-8mol/L。连续平行测定2.0×10-5mol/L的舒必利溶液10次,发光强度值的相对标准偏差(RSD)为1.56%。对样品进行回收率试验,回收率在95.0%～105.0%之间,RSD为4.43%(n=5)。该方法具有较高的选择性和灵敏度,样品处理简单快速,用于药物中舒必利的测定,结果满意。     

固定Ionic liquid/Silica sol/Nafion膜中的联吡啶钌电化学发光行为的研究及应用

制备了Ionic liquid/Silica sol/Nafion-联吡啶钌复合物膜修饰金电极。采用循环伏安(CV)和电致化学发光(ECL)法,考察了联吡啶钌和左氧氟沙星在此修饰电极上的电化学及其发光行为。结果表明,此修饰电极表现出很好的电化学活性和电化学发光响应。基于左氧氟沙星对固定化联吡啶钌在0.1 mol/L磷酸盐缓冲液中的弱电化学发光信号有较强的增敏作用,建立了电化学发光检测盐酸左氧氟沙星的新方法。在最佳实验条件下,左氧氟沙星浓度在1.0×10-7～1.0×10-4mol/L范围内与相对发光强度呈线性关系(r2=0.998 4),检出限(S/N=3)为1.59×10-9mol/L。连续平行测定2.2×10-5mol/L的左氧氟沙星溶液10次,发光强度的相对标准偏差(RSD)为3.6%。对样品进行回收率试验,回收率在95.6%～103.5%之间,RSD(n=5)为3.0%。该方法具有较高的选择性和灵敏度,样品处理简单快速,用于盐酸左氧氟沙星的测定,结果满意。     

Nano-Au/Silica sol/PVP修饰金电极上电化学发光测定盐酸硫必利

采用溶胶-凝胶法制备了Nano-Au/Silica sol/PVP修饰金电极,并基于盐酸硫必利对联吡啶钌(Ru(bpy)2+3)在该修饰电极上弱电化学发光具有较强的增敏作用,建立了电化学发光检测盐酸硫必利的新方法。在最佳实验条件下,盐酸硫必利浓度在1.0×10-7~1.0×0-4 mol/L范围内与相对发光强度呈线性关系(r2=0.9978),检出限(S/N=3)为6.7×10-10 mol/L。连续平行测定1.0×10-5 mol/L盐酸硫必利溶液10次,发光强度的相对标准偏差(RSD)为1.78%。对样品进行回收率试验,其回收率在97.7%~103.9%之间,RSD为2.62%。该方法具有较高的选择性和灵敏度,样品处理简单快速,用于盐酸硫必利的测定,结果满意。     

Unique {H(SiR(3))(2)}, (H(2)SiR(3)), H(HSiR(3)), and (H(2))SiR(3) ligand sets supported by the {Fe(Cp)(L)} platform (L=CO, PR(3))

This work deals with the type and incidence of nonclassical Si--H and H--H interactions in a family of silylhydride complexes [Fe(Cp)(OC)(SiMe(n)Cl(3-n))H(X)] (X=SiMe(n)Cl(3-n), H, Me, n=0-3) and [Fe(Cp)(Me(3)P)(SiMe(n)Cl(3-n))(2)H] (n=0-3). DFT calculations complemented by atom-in-molecule analysis and calculations of NMR hydrogen-silicon coupling constants revealed a surprising diversity of nonclassical Si--H and H--H interligand interactions. The compounds [Fe(Cp)(L)(SiMe(n)Cl(3-n))(2)H] (L=CO, PMe(3); n=0-3) exhibit an unusual distortion from the ideal piano-stool geometry in that the silyl ligands are strongly shifted toward the hydride and there is a strong trend towards flattening of the {FeSi(2)H} fragment. Such a distortion leads to short Si--H contacts (range 2.030-2.075 A) and large Mayer bond orders. A novel feature of these extended Si--H interactions is that they are rather insensitive towards the substitution at the silicon atom and the orientation of the silyl ligand relatively the Fe--H bond. NMR spectroscopy and bonding features of the related complexes [Fe(Cp)(OC)(SiMe(n)Cl(3-n))H(Me)] (n=0-3) allow for their rationalization as usual eta(2)-Si--H silane sigma-complexes. The series of "dihydride" complexes [Fe(Cp)(OC)(SiMe(n)Cl(3-n))H(2)] (n=0-3) is different from the previous two families in that the type of interligand interactions strongly depends on the substitution on silicon. They can be classified either as usual dihydrogen complexes, for example, [Fe(Cp)(OC)(SiMe(2)Cl)(eta(2)-H(2))], or as compounds with nonclassical H--Si interactions, for example, [Fe(Cp)(OC)(H)(2)(SiMe(3))] (16). These nonclassical interligand interactions are characterized by increased negative J(H,Si) (e.g. -27.5 Hz) and increased J(H,H) (e.g. 67.7 Hz).     

Syntheses and structures of the infinite chain compounds Cs(4)Ti(3)Se(13), Rb(4)Ti(3)S(14), Cs(4)Ti(3)S(14), Rb(4)Hf(3)S(14), Rb(4)Zr(3)Se(14), Cs(4)Zr(3)Se(14), and Cs(4)Hf(3)Se(14)

The alkali metal/group 4 metal/polychalcogenides Cs(4)Ti(3)Se(13), Rb(4)Ti(3)S(14), Cs(4)Ti(3)S(14), Rb(4)Hf(3)S(14), Rb(4)Zr(3)Se(14), Cs(4)Zr(3)Se(14), and Cs(4)Hf(3)Se(14) have been synthesized by means of the reactive flux method at 823 or 873 K. Cs(4)Ti(3)Se(13) crystallizes in a new structure type in space group C(2)(2)-P2(1) with eight formula units in a monoclinic cell at T = 153 K of dimensions a = 10.2524(6) A, b = 32.468(2) A, c = 14.6747(8) A, beta = 100.008(1) degrees. Cs(4)Ti(3)Se(13) is composed of four independent one-dimensional [Ti(3)Se(13)(4-)] chains separated by Cs(+) cations. These chains adopt hexagonal closest packing along the [100] direction. The [Ti(3)Se(13)(4-)] chains are built from the face- and edge-sharing of pentagonal pyramids and pentagonal bipyramids. Formal oxidation states cannot be assigned in Cs(4)Ti(3)Se(13). The compounds Rb(4)Ti(3)S(14), Cs(4)Ti(3)S(14), Rb(4)Hf(3)S(14), Rb(4)Zr(3)Se(14), Cs(4)Zr(3)Se(14), and Cs(4)Hf(3)Se(14) crystallize in the K(4)Ti(3)S(14) structure type with four formula units in space group C(2)(h)()(6)-C2/c of the monoclinic system at T = 153 K in cells of dimensions a = 21.085(1) A, b = 8.1169(5) A, c = 13.1992(8) A, beta = 112.835(1) degrees for Rb(4)Ti(3)S(14);a = 21.329(3) A, b = 8.415(1) A, c = 13.678(2) A, beta = 113.801(2) degrees for Cs(4)Ti(3)S(14); a = 21.643(2) A, b = 8.1848(8) A, c = 13.331(1) A, beta = 111.762(2) degrees for Rb(4)Hf(3)S(14); a = 22.605(7) A, b = 8.552(3) A, c = 13.880(4) A, beta = 110.919(9) degrees for Rb(4)Zr(3)Se(14); a = 22.826(5) A, b = 8.841(2) A, c = 14.278(3) A, beta = 111.456(4) degrees for Cs(4)Zr(3)Se(14); and a = 22.758(5) A, b = 8.844(2) A, c = 14.276(3) A, beta = 111.88(3) degrees for Cs(4)Hf(3)Se(14). These A(4)M(3)Q(14) compounds (A = alkali metal; M = group 4 metal; Q = chalcogen) contain hexagonally closest-packed [M(3)Q(14)(4-)] chains that run in the [101] direction and are separated by A(+) cations. Each [M(3)Q(14)(4-)] chain is built from a [M(3)Q(14)] unit that consists of two MQ(7) pentagonal bipyramids or one distorted MQ(8) bicapped octahedron bonded together by edge- or face-sharing. Each [M(3)Q(14)] unit contains six Q(2)(2-) dimers, with Q-Q distances in the normal single-bond range 2.0616(9)-2.095(2) A for S-S and 2.367(1)-2.391(2) A for Se-Se. The A(4)M(3)Q(14) compounds can be formulated as (A(+))(4)(M(4+))(3)(Q(2)(2-))(6)(Q(2-))(2).     

Organic acid solutions in the chromatography of inorganic ions VIII. Cation-exchange of Mn(II), Cd(II), Co(II), Ni(II), Zn(II), Cu(II), Fe(III), Sc(III), Y(III), Eu(III), Dy(III), Ho(III), Yb(III), Ti(IV) and Nb(V) in malate media

Summary The cation-exchange behaviour of Mn(II), Cd(II), Co(II), Ni(II), Zn(II), Cu(II), Fe(III), Sc(III), Y(III), Eu(III), Dy(III), Ho(III), Yb(III), Ti(IV) and Nb(V) in malate media at various concentrations and pH, was studied with Dowex 50 WX8 resin (200–400 mesh) in the ammonium form. Separation of Fe(III)/Cu(II), Fe(III)/Cu(II)/Zn(II), Fe(III)/Co(II)/Mn(II), Cu(II)/Ni(II)/Mn(II), Fe(III)/Cu(II)/Co(II)/Mn(II), Fe(III)/Cu(II)/Ni(II)/Cd(II), Yb(III)/Eu(III), Sc(III)/Y(III),Sc(III)/Yb(III)/Dy(III) and Nb(V)/Yb(III)/Ho(III) has been achieved, among others.This work was supported by C.N.R. of Italy.     

(K_(0.485)Na_(0.485)Li_(0.03))NbO_3-Pb(Zr_(0.53)Ti_(0.47))O_3陶瓷的介电铁电性能

采用传统电子陶瓷工艺制备新型钙钛矿体系(1-x)(K_(0.485)Na_(0.485)Li_(0.03))NbO_3-Pb(Zr_(0.53)Ti_(0.47))O_3陶瓷,研究了该体系陶瓷的介电铁电性能.X射线衍射分析表明:所有陶瓷样品都具有单一的钙钛矿结构,在0.65≤x≤0.75时,出现明显的正交相和四方相的准同型相界区.测试结果表明:陶瓷具有高介电常数.低介质损耗,良好的温度稳定性;获得了饱和的电滞回线,显示了优良的铁电性能.尤其在x=0.75时各项性能达到最佳,其中介电常数ε_r=1590,介电损耗tan δ=0.017,居里温度T_c=295℃,剩余极化强度P,=28.6 μC·cm~(-1),矫顽场强E_c=0.89 kV·mm~(-1).     

Hexaaquacobalt(II) bis(hypophosphite) and hexaaquacobalt(II)/nickel(II) bis(hypophosphite)

The title compounds, hexa­aqua­cobalt(II) bis­(hypophosphite), [Co(H₂O)₆](H₂­PO₂)₂, and hexa­aqua­cobalt(II)/nickel(II) bis(hypophosphite), [Co_0.5Ni_0.5(H₂O)₆](H₂PO₂)₂, are shown to adopt the same structure as hexa­aqua­magnesium(II) bis­(hypophosphite). The packing of the Co(Ni) and P atoms is the same as in the structure of CaF₂. The Co^II(Ni^II) atoms have a pseudo‐face‐centred cubic cell, with a = b～ 10.3 Å, and the P atoms occupy the tetrahedral cavities. The central metal cation has a slightly distorted octahedral coordination sphere. The geometry of the hypophosphite anion in the structure is very close to ideal, with point symmetry mm2. Each O atom of the hypophosphite anion is hydrogen bonded to three water mol­ecules from different cation complexes, and each H atom of the hypophosphite anion is surrounded by three water mol­ecules from further different cation complexes.     

A crossed molecular beam study on the formation of hexenediynyl radicals (H(2)CCCCCCH; C(6)H(3) (X(2)A')) via reactions of tricarbon molecules, C(3)(X(1)Sigma(g)(+)), with allene (H(2)CCCH(2); X(1)A(1)) and methylacetylene (CH(3)CCH; X(1)A(1))

Crossed molecular beams experiments have been utilized to investigate the reaction dynamics between two closed shell species, i.e. the reactions of tricarbon molecules, C(3)(X(1)Sigma(g)(+)), with allene (H(2)CCCH(2); X(1)A(1)), and with methylacetylene (CH(3)CCH; X(1)A(1)). Our investigations indicated that both these reactions featured characteristic threshold energies of 40-50 kJ mol(-1). The reaction dynamics are indirect and suggested the reactions proceeded via an initial addition of the tricarbon molecule to the unsaturated hydrocarbon molecules forming initially cyclic reaction intermediates of the generic formula C(6)H(4). The cyclic intermediates isomerize to yield eventually the acyclic isomers CH(3)CCCCCH (methylacetylene reaction) and H(2)CCCCCCH(2) (allene reaction). Both structures decompose via atomic hydrogen elimination to form the 1-hexene-3,4-diynyl-2 radical (C(6)H(3); H(2)CCCCCCH). Future flame studies utilizing the Advanced Light Source should therefore investigate the existence of 1-hexene-3,4-diynyl-2 radicals in high temperature methylacetylene and allene flames. Since the corresponding C(3)H(3), C(4)H(3), and C(5)H(3) radicals have been identified via their ionization potentials in combustion flames, the existence of the C(6)H(3) isomer 1-hexene-3,4-diynyl-2 can be predicted as well.