On-line monitoring of traces of aromatic-, phenolic- and chlorinated components in flue gases of industrial scale incinerators and cigarette smoke by direct-inlet laser ionization-mass spectrometry (REMPI-TOFMS)

The combination of laser induced resonance-enhanced multiphoton ionization (REMPI) and time-of-flight mass spectrometry (TOFMS) represents a highly selective as well as sensitive analytical technique, well suited for species selective real-time, on-line monitoring of trace-gases. Results presented are obtained with a newly designed, mobile REMPI-TOFMS instrument, optimized for field applications. The mobile REMPI-TOFMS device either is equipped with a compact excimer laser (KrF, λ = 248 nm) or a small Nd:YAG laser (forth harmonic frequency, λ = 266 nm). A special effusive molecular beam inlet system was used, which allows direct inlet of flue gases from e.g. waste incinerators without memory effects for compounds of a molecular weight of up to 260–280 amu. Detection sensitivities in the sub-ppb region are achieved under field measurement conditions. Applications concerning on-line monitoring of combustion byproducts and fuel components are presented. This includes on-line analysis of polycyclic aromatic hydrocarbons (PAH) in the flue gas of a 0.5 MW waste incineration pilot plant, headspace analysis of wood gasification products and crude oil composition (fuel analysis) as well as highly time resolved (single puff resolution) on-line analysis of cigarette smoke. The application of the on-line REMPI-TOFMS monitor for continuous analysis of dioxin indicators in the flue gas of e.g. hazardous waste incinerators is discussed.     

Mobile resonance enhanced multiphoton ionisation-time-of-flight mass spectrometer with a novel hybrid laser desorption/molecular beam ion source for rapid detection of aromatic trace compounds from gas phase and solid samples

A mobile, field applicable resonance enhanced multiphoton ionisation-time-of-flight mass spectrometer (REMPI-TOFMS) for direct-inlet gas-phase analysis as well as for characterisation of solid samples, has been developed. For solid-sample analysis, laser desorption (LD) with IR-laser pulses is used for volatilisation of the neutral analytes from a target in the ion source prior to REMPI-TOFMS analysis. For direct inlet gas-phase analysis, a needle gas inlet is used and the formed molecular beam is REMPI-ionised directly in the ion source. A special ion source was developed, which can be rapidly interchanged between the REMPI-TOFMS and the LD-REMPI-TOFMS modes. The system is equipped with a tuneable optical parametrical oscillator (OPO)-laser system. The analytical properties are characterised for both modes of operations. In both cases, analytical performance is similar to that achieved with instruments specifically designed for either gas-phase or solid-phase characterisation. Results from field measurements of a wood combustion flue gas of a 174 kW bio mass furnace are given. Gas-phase analysis was applied for time-resolved on-line REMPI-TOFMS of the semi-volatile aromatic flue gas constituents. The low-volatile aromatic compounds, which were precipitated with the particulate matter in the filtering unit of the sampling train, were characterised by direct LD-REMPI-TOFMS of the glass fibre filter material. By combining the gas-phase and particulate results a rather comprehensive characterisation of the aromatic species present in the flue gas (i.e. aerosol--gas phase plus particulate matter) was achieved.     

Continuous measurement of metals in flue gas using ICP-OES

A system capable of continuously measuring a range of metallic elements in the effluent gas from incinerators and other similar industrial processes, and providing on-line results has been developed. With a state-of-the-art mobile laboratory measurements were taken from a UK municipal solid waste incinerator. The detection system used was an ICP-OES, with a modified torch to allow the introduction of flue gas directly into the plasma. Metals that were investigated were Ni, Hg, V, Al, Na, Ca, Cu, Sn, Pb, Sb, As, Cd and Tl, with limits of detection in the range 0.0004 mg m^–3 to 0.1 mg m^–3 being calculated. Emission measurements produced data that showed that the MSWI plants emission were significantly lower than the emission limits specified in EC 2000/76/EC.     

Direct observation of the formation of aromatic pollutants in waste incineration flue gases by on-line REMPI-TOFMS laser mass spectrometry

On-line REMPI-TOFMS laser mass spectrometry (Resonance Enhanced Multi-Photon Ionization-Time-Of-Flight Mass Spectrometry) was used to monitor combustion and pyrolysis byproducts from industrial combustion processes, including polycyclic aromatic hydrocarbons (PAH) and monochlorobenzene in the flue gas of an industrial 22 MW hazardous waste incineration plant. Sampling at different places in the flue gas stream revealed the complexity of the processes responsible for the formation of the different chemical species, while time resolved measurements depicted the emission dynamics.     

Direct observation of the formation of aromatic pollutants in waste incineration flue gases by on-line REMPI-TOFMS laser mass spectrometry

On-line REMPI-TOFMS laser mass spectrometry (Resonance Enhanced Multi-Photon Ionization – Time-Of-Flight Mass Spectrometry) was used to monitor combustion and pyrolysis byproducts from industrial combustion processes, including polycyclic aromatic hydrocarbons (PAH) and monochlorobenzene in the flue gas of an industrial 22 MW hazardous waste incineration plant. Sampling at different places in the flue gas stream revealed the complexity of the processes responsible for the formation of the different chemical species, while time resolved measurements depicted the emission dynamics.     

Spectrofluorometric determination of hesperidin by manual and flow-injection methods

A reliable and highly sensitive method for the determination of hesperidin is described. It involves the formation of a highly fluorescent complex between hesperidin and aluminium (III) in a micellar medium. There is a linear relationship between fluorescence intensity (λ_em = 496 nm, λ_ex = 391 nm) and hesperidin concentration over the range 5 × 10^–7– 2 × 10^–5 mol L^–1. The detection limit is 79 μg L^–1. The method can easily be adapted to a flow system using a three-channel manifold, the peak height being proportional to the hesperidin concentration over the range 1 × 10^–6– 1 × 10^–4 mol L^–1. Manual and flow-injection procedures have been successfully applied to the determination of hesperidin in orange peel and orange juice. Received: 21 October 1998 / Revised: 16 December 1998 / Accepted: 25 December 1998     

Liquid-chromatographic determination of sulfadimidine in milk and eggs

A method for the determination/identification of residual sulfadimidine (SDD) in milk and eggs by high-performance liquid chromatography (HPLC) with a photo-diode array detector was developed. The sample preparation was performed by shaking with a mixture of 20% (w/v) trichloroacetic acid-methanol (4:1, v/v) followed by ultra-filtration using Molcut II^?. A LiChrospher^? 100 RP-8 (e) column and a mobile phase of 4% (v/v) acetic acid solution-acetonitrile (6:4, v/v) were used. The average recoveries from spiked SDD samples were 80.8–88.0% with coefficients of variation of 2.8–5.5%. The limits of detection in milk and eggs were 0.01 μg/mL and 0.01 μg/g, respectively. The total time required for the analysis of one sample was less than 20 min. Received: 7 October 1998 / Revised: 29 December 1998 / Accepted: 30 December 1998     

A new concept for the bioeffects-related analysis of xenoestrogens: Hyphenation of receptor assays with LC-MS

The wide variety of known and unknown endocrine disruptors demands highly efficient methods for detecting the relevant endocrine disrupting pollutants. Bioeffects-related analysis is expected to solve this problem, combining biomolecular recognition processes with chemical analysis, which therefore reduces costs of instrumental chemical analysis to relevant samples. The hyphenation of both steps provides information on potential bioeffects, structure and concentration of the substances of interest. In this work the hyphenation of an enzyme-linked receptor assay (ELRA) with liquid chromatography-tandem mass spectrometry (LC-MSMS) for the analysis of estrogens and xenoestrogens is proposed. Both test systems have been validated with standards and spiked real water samples. The ELRA achieved a detection limit of 0.1 μg/L for 17β-estradiol (without preconcentration). With the LC-MSMS method, steroids could be detected down to 1 ng/L (with preconcentration). Two concepts for a tighter hyphenation of biomolecular interaction and chemical analysis are discussed: the on-line coupling of receptor-affinity chromatography (RAC) to LC-MSMS and the direct measurement of receptor-ligand complexes by LC-MSMS. Received: 30 October 1998 / Revised: 18 December 1998 / Accepted: 26 December 1998     

A new concept for the bioeffects-related analysis of xenoestrogens: Hyphenation of receptor assays with LC-MS

The wide variety of known and unknown endocrine disruptors demands highly efficient methods for detecting the relevant endocrine disrupting pollutants. Bioeffects-related analysis is expected to solve this problem, combining biomolecular recognition processes with chemical analysis, which therefore reduces costs of instrumental chemical analysis to relevant samples. The hyphenation of both steps provides information on potential bioeffects, structure and concentration of the substances of interest. In this work the hyphenation of an enzyme-linked receptor assay (ELRA) with liquid chromatography-tandem mass spectrometry (LC-MSMS) for the analysis of estrogens and xenoestrogens is proposed. Both test systems have been validated with standards and spiked real water samples. The ELRA achieved a detection limit of 0.1 μg/L for 17β-estradiol (without preconcentration). With the LC-MSMS method, steroids could be detected down to 1 ng/L (with preconcentration). Two concepts for a tighter hyphenation of biomolecular interaction and chemical analysis are discussed: the on-line coupling of receptor-affinity chromatography (RAC) to LC-MSMS and the direct measurement of receptor-ligand complexes by LC-MSMS. Received: 30 October 1998 / Revised: 18 December 1998 / Accepted: 26 December 1998     

不同垃圾焚烧炉排放的PM10 中多环芳烃的研究

对大气可吸入颗粒物采样器进行改装，建立了垃圾焚烧炉烟气中PM10采样系统，并采集了三家垃圾发电厂焚烧炉排放烟气中的可吸入颗粒物。利用GC-MS对可吸入颗粒物中的16种多环芳烃进行定量研究，获得了多环芳烃的质量分数和浓度，并对不同环数的芳烃进行了比较，分析了不同样品中的多环芳烃的毒性参数。结果表明，颗粒物中的多环芳烃主要集中在4环、5环和6环，3环和2环所占比例较少；与燃煤电厂相比，垃圾焚烧发电厂排放的烟气中多环芳烃的浓度和毒性参数更高。     

The topology of catchment regions of potential energy hypersurfaces

A simple proof is presented for a fundamental topological property of catchment regions of potential energy hypersurfaces: each catchment region C(λ,i), representing a chemical species and its conformational range on the potential energy hypersurface, is simply k-connected for each dimension k=1,2,…3N−6−λ, where λ is the index of the catchment region. The consequences of this property on the structure of the fundamental group of reaction mechanisms (the one-dimensional homotopy group of reaction paths) is discussed. Received: 8 July 1998 / Accepted: 6 October 1998 / Published online: 23 February 1999     

Chromatographic determination of phenylarsenic compounds

Urinary arsenic speciation is considered to be an effective procedure to differentiate between toxic inorganic and less toxic organic arsenic exposure. The aim of the present work was to develop a new method for the simultaneous determination of the main arsenic species so far detected in urine: arsenite (As(III)), arsenate (As(V)), methylarsonic acid (MA), dimethylarsinic acid (DMA), and arsenobetaine (AsB). The method is based on anion exchange HPLC coupled on-line to an inductively coupled plasma mass spectrometer (ICP-MS) for element specific detection. Experimental parameters, such as column type and composition of the mobile phases were optimized in order to get best separation, little matrix interferences, lowest detection limits, and short total times of analyses. Best chromatographic conditions were obtained by using a Dionex AS14 anion exchange column and a gradient elution with tetramethylammonium hydroxide and ammonium carbonate as eluting compounds. The detection limits (3 σ) were found to be in the sub μg L^–1 range. The method was applied to analyze different urine samples from persons with and without consumption of seafood. To avoid significant matrix influences, samples (24 h urine) had to be diluted 1 : 5 with water and were filtered through a 0.45 μm filter prior to analyses. Special attention was focused on the validation of the method according to the regulations of the “Deutsche Forschungsgemeinschaft” (DFG) for the analyses of hazardous substances in biological materials. Received: 22 December 1997 / Revised: 18 February 1998 / Accepted: 22 February 1998     

New sorbents and indicator powders for preconcentration and determination of trace metals in liquid samples

Two approaches to immobilize complex-forming analytical reagents (PAN, PAR, Xylenol orange, Brombenzothiazo, Crystal violet, Cadion, and Sulfochlorophenolazorhodanine) for the preparation of new sorbents and indicator powders are suggested: on-line coating of reversed-phase silica gel by reagents or doping of porous sol-gel silica with reagents. The retention of Ag, Cd, Cu(II), Co(II), Fe(III), Mn(II), Ni, Pb, and Zn on the sorbents developed was investigated. Quantitative sorption and desorption conditions were optimized. Procedures for the determination of Cd, Cu(II), Fe(III), Pb, and Zn with flame atomic absorption, spectrophotometric, and diffusion scattering spectrometric detection were elaborated. Detection limits for Cd, Cu(II), Fe(III), Pb, and Zn were 3 μg/L, 6 μg/L, 5 μg/L, 40 μg/L, and 1 μg/L, respectively. The procedures were used for the analysis of various real samples, e.g., natural and waste waters, and food. Received: 17 July 1997 / Revised: 20 January 1998 / Accepted: 5 February 1998     

Simultaneous on-line size and chemical analysis of gas phase and particulate phase of cigarette mainstream smoke

This paper describes the combined set-up of on-line chemical analysis of gas phase by single-photon ionisation/resonance enhanced multiphoton ionisation–time-of-flight mass spectrometry (SPI/REMPI-TOFMS) and on-line particle size analysis by differential electrical mobility particle spectrometry (DMS 500) for the investigation of fresh cigarette mainstream smoke. SPI is well suited for the investigation of a great variety of organic species, whereas REMPI is highly sensitive for aromatic compounds. Gas phase measurements of filtered and unfiltered smoke are possible with the SPI/REMPI-TOFMS in order to determine the influence of the presence of particles on the chemical composition of the gas phase. Initial results are shown for the characterisation and comparison of three pure Virginia tobacco research cigarettes having filter ventilations of 0%, i.e. no filter ventilation, 35% and 70% ventilation. The three cigarette types are smoked under two different smoking regimes, a standard regime using puff parameters equivalent to the conventional International Standard Organisation regime and a more intense smoking regime. For the gas phase, qualitative puff-by-puff resolved yields of three selected compounds (acetaldehyde, phenol and styrene) are shown and compared. For particulate matter, particle number, count median diameter and total surface area are illustrated on a puff-by-puff basis. Yields of the chemicals analysed, puff number and surface area are in good agreement with the intensity of the smoking regime and the dilution of smoke by filter ventilation. However, gaseous compounds are influenced differently, depending whether an absolute particle filter is present or not, i.e. they can be totally removed (phenol), partially removed (styrene) or not affected (acetaldehyde). For particle analysis, the count median diameter decreases from puff to puff and is strongly dependent on the smoking regime and ventilation rate. Thereby, 0% ventilated cigarettes smoked under the intense regime result in the smallest count median diameters of ca. 180 nm, whereas 70% ventilated cigarettes smoked with a standard regime lead to the largest values of up to 280 nm. As particle diameter increases, particle number decreases as a consequence of increasing time for particle coagulation.     

Validation of an HPLC method for the determination of *-dichlorobenzene and naphthalene in mothrepellents

 The determination of dichlorobenzene and naphthalene in commercial repellents used in Spain has been validated. This was done using an isocratic regime, to test the reverse -phase HPLC system with acetonitrile: water 65 : 35 (v: v) as the mobile phase, at 20  °C. This technique is proposed for the modular validation of the HPLC system . The results obtained with this method show good agreement with the results provided by the manufacturers of the mothrepellents. Received: 21 December 1998 / Accepted: 4 May 1999     

Data correlation in on-line solid-phase extraction-gas chromatography-atomic emission/mass spectrometric detection of unknown microcontaminants

Summary A procedure is described for the (non-target) screening of hetero-atom-containing compounds in tap and waste water by correlating data obtained by gas chromatography (GC) using atomic emission (AED) and mass selective (MS) detection. Solid-phase extraction (SPE) was coupled on-line to both GC systems to enable the determination of microcontaminants at the 0.02–1 μg L⁻¹ level in 7–50 mL of aqueous sample. The screening was limited to compounds present in at least one heteroatom-selective GC-AED trace above a predetermined concentration level. These compounds were identified by their partial formulae (AED) and the corresponding mass spectra, which were obtained from the GC-MS chromatogram via the retention index concept. The potential of the approach was demonstrated by the identification of target compounds as well as all unknowns present in tap and waste water above the predetermined threshold of 0.05 μg L⁻¹ (tap water) or 0.5 μg L⁻¹ (waste water).     

Sensitive and selective determination of metabolically formed trans-dihydrodiols and phenols of benzo[a]pyrene in water and urine samples by HPLC with amperometric detection

A method has been developed to separate hydroxylated metabolites of the carcinogenic polycyclic aromatic hydrocarbon benzo[a]pyrene, i. e. trans-4,5-, 7,8-, 9,10-dihydrodiol and 1-, 3-, 7-, and 9-phenol, by HPLC with amperometric detection employing an isocratic methanol/water eluent (70:30, v/v) containing 0.5 g/L sulfuric acid and 1 g/L lithium perchlorate. Compared with the usually applied fluorescence (λ_ex = 265 nm, λ_em = 460 nm) and ultraviolet (λ = 265 nm) detection, the amperometric technique is about 2–12 times more sensitive for the determination of all metabolites investigated. The method was applied to the determination of the seven metabolites of benzo[a]pyrene in different water samples and in urine after solid-phase extraction (SPE). The results obtained by HPLC with amperometric detection after SPE enrichment from an aqueous extract of a soil sample and from the urine of a rat intragastrically treated with benzo[a]pyrene agreed well with the values determined with fluorescence and/or UV detection. Received: 20 December 1996 / Revised: 10 March 1997 / Accepted: 30 April 1997     

Analysis of tetrapyrrolic pigments and derivatives in sediments by high performance liquid chromatography/atmospheric pressure chemical ionization mass spectrometry

A new application is described of the on-line high-performance liquid chromatography/positive and negative ion atmospheric pressure chemical ionization mass spectrometry (APCI(+/–)-MS) to the identification of tetrapyrrolic compounds in sediment samples containing complex mixtures of natural pigments and their diagenetic products. The method relies on the production of radical anions in order to determine the molecular masses of the molecules which yield abundant fragment ions when analyzed in the positive mode. This approach allows to verify the occurrence of coeluting components by examining their negative ion spectra and to complete their identification on the basis of their fragment ions produced in the positive ion spectra. Received: 24 September 1998 / Revised: 23 December 1998 / Accepted: 29 December 1998     

Analysis of tetrapyrrolic pigments and derivatives in sediments by high performance liquid chromatography/atmospheric pressure chemical ionization mass spectrometry

A new application is described of the on-line high-performance liquid chromatography/positive and negative ion atmospheric pressure chemical ionization mass spectrometry (APCI(+/–)-MS) to the identification of tetrapyrrolic compounds in sediment samples containing complex mixtures of natural pigments and their diagenetic products. The method relies on the production of radical anions in order to determine the molecular masses of the molecules which yield abundant fragment ions when analyzed in the positive mode. This approach allows to verify the occurrence of coeluting components by examining their negative ion spectra and to complete their identification on the basis of their fragment ions produced in the positive ion spectra. Received: 24 September 1998 / Revised: 23 December 1998 / Accepted: 29 December 1998