Determination of pharmaceutical and personal care products in wastewater by capillary electrophoresis with UV detection

Capillary electrophoresis (CE) offers a fast and cost-effective alternative analytical technique to LC-MS/MS for separation and quantitation of many PPCP compounds in wastewater. In this study, we have developed a method that can simultaneously analyze eight different PPCP compounds in untreated wastewater (ibuprofen, triclosan, carbamazepine, caffeine, acetaminophen, sulfamethoxazole, trimethoprim, and lincomycin), using capillary electrophoresis with UV detection (CE-UV). The method detection limit (MDL) ranged from 1.6 to 68.7 ppb through solid phase extraction. The standard limit of quantification (LOQ) ranged from 0.63 to 7.72 ppm. Factors affecting separation and quantification of PPCPs, such as pH, electrophoretic potential, buffer strength, buffer type, and additives, were investigated and optimized. Water samples from two different wastewater treatment plants were collected and analyzed. The results obtained were comparable with those of LC-MS/MS. The technique developed in this study provides a low cost, simple, fast, and relatively sensitive method for determination of various PPCPs in wastewater samples for PPCP screening.     

Traceability without uncertainty: current situation in the pharmaceutical industry

The current situation in the pharmaceutical industry is discussed, when the traceability of measurement (analytical) results to certified values of pharmacopoeial reference standards is required, without evaluating their uncertainties. It is shown that the evaluation of measurement uncertainty is necessary for understanding the level of confidence of the analytical results and their comparability, particularly during preparation and characterisation of the reference standards.Papers published in this section do not necessarily reflect the opinion of the Editors, the Editorial Board and the Publisher. Apart from exceptional circumstances, they are not submitted to the usual referee procedure and go essentially unaltered.     

Electronic tongue for pharmaceutical analytics: quantification of tastes and masking effects

The organoleptic aspects of pharmaceutical formulations affect their acceptability to the patient and hence can have an important effect on concordance with treatment. Objective evaluation of these aspects, particularly the taste of the formulation and the drug substance it contains, is difficult. Whilst volunteer taste panels can be used to good effect their utility is limited, particularly during very early stage development when the toxicological profile of the active pharmaceutical ingredient (API) is yet to be established in detail. A potentiometric electronic tongue has been applied to analyse a variety of 41 individual substances and mixtures of particular interest for pharmaceutical research and development. The electronic tongue (ET) was capable of discriminating between substances with different taste modalities and could also distinguish different substances eliciting the same basic taste; the ET is promising in terms of quantifying the content of each substance and has an ability to detect nuances of the basic taste (e.g. lingering or short-lived). After calibration the electronic tongue was successfully applied to predicting bitterness strength of binary mixtures with a sweetener in terms of apparent or perceived quinine content. In order to render a formulation palatable it is often necessary to mask the (usually bitter) taste of the API by the addition of masking agents such as sweeteners and flavours. The ET proved capable of distinguishing between formulations with different levels of sweetener and/or flavour in a manner that was consistent with their masking efficiency as perceived by a small human taste panel. A suitably calibrated ET could have the benefit of providing the pharmaceutical formulator with reliable data concerning the taste of the product quickly and with a reduced need to ask volunteers to taste active pharmaceutical samples. Early development activities could be facilitated when human tasting is usually not possible in the absence of the required toxicological data.     

Quality management in analytical R&D in the pharmaceutical industry: Building quality from GLP

 The pharmaceutical industry is one of the most regulated activity sectors. The regulation includes specific quality systems such as good laboratory practice (GLP), good clinical practice (GCP) and good manufacture practice (GMP). The principles of GLP mainly cover the formal quality aspects of a procedure and do not evaluate the technical aspects in depth. On the other hand, EN 45001 accreditation covers technical performance and is not suitable for pharmaceutical research and development (R&D) as it is almost impossible to comply with the requirements of the European standard in the pharmaceutical environment. The challenge to the pharmaceutical industry is, therefore, to develop quality systems, compatible with GLP principles, that not only cover formal quality items but also ensure good scientific and technical performance. An implementation process focused on real quality improvement is the best way to achieve this objective, culminating in formal recognition of the quality system by third-party assessment. In the case of analytical R&D, the EURACHEM/CITAC Guide CG2 is a very good tool that can help in the definition, analysis and selection of the non GLP quality elements that will be useful. Received: 30 June 1999 / Accepted: 18 October 1999     

A new non-invasive, quantitative Raman technique for the determination of an active ingredient in pharmaceutical liquids by direct measurement through a plastic bottle

The concentration of an active pharmaceutical ingredient (povidone) in a commercial eyewash solution has been measured directly through a plastic (low-density polyethylene: LDPE) container using a wide area illumination (WAI) Raman scheme. The WAI scheme allows excitation using a 6 mm laser spot (focal length: 248 mm) that is designed to cover a wide sample area. As a result, it has the potential to improve the reliability Raman measurements by significantly enhancing representative sample interrogation, thus improving the reproducibility of sampling. It also decreases the sensitivity of sample placement with regard to the excitation focal plane. Simultaneously, isobutyric anhydride was placed in front of the bottles to use for a synchronous external standard configuration. This helps to correct the problematic variation of Raman intensity from the inherent fluctuation in laser power. Using the WAI Raman scheme combined with the synchronous standard method, the povidone concentration was successfully measured with spectral collection that was performed through a plastic barrier. The conventional Raman scheme was difficult to employ for the same purpose because of the degraded spectral reproducibility resulting from the smaller laser illumination area and the sensitivity of such an approach to the position of the sample bottle. The result from this study suggests that the WAI scheme exhibits a strong potential for the non-destructive quantitative analysis of pharmaceuticals measured directly in plastic containers. Preliminary work also shows that similar measurements can also be made in glass bottles. If implemented, this technique could be utilized as a simple and rugged method for quality assurance of final products in a manner consistent with Process analytical technology (PAT) requirements.     

Comparison of three different phosphorescent methodologies in solution for the analysis of naphazoline in pharmaceutical preparations

We present results from a comparative study of three proposed phosphorimetric methods for determination of naphazoline (NPZ) in solution. The first method is based on use of micelles to stabilize phosphorescence signals in solutions at room temperature (MS-RTP). The second is based on the use of a heavy atom salt and sodium sulfite as an oxygen scavenger to obtain room-temperature phosphorescence (HAI-RTP) in solution. The last method employs an optical sensor for NPZ based on the phosphorescent properties of the analyte on a solid sensor phase. The aim of this work was to compare time consumption, simplicity, sensitivity, selectivity, detection, and quantification limits for use of these three phosphorimetric methods to determine naphazoline in pharmaceutical preparations. The most simple, sensitive, and reproducible of the three methods for naphazoline analysis is the HAI-RTP method. Detection limits are 4.9, 1.7, and 9.4 ng mL^–1, respectively, for the MS-RTP, HAI-RTP, and optosensor methods.     

UV-absorption and fluorimetric methods for the determination of alprazolam in pharmaceutical formulation

The development of UV and fluorescence spectrophotometric methods for the quantitative determination of alprazolam in dosage forms using As(III)?SDS system. The two simple and sensitive, spectrophotometric and spectrofluorimetric methods were developed for the determination of alprazolam (ALP) in tablets. These methods are based on formation of ALP?As(III) complex in the presence of SDS. The UV-spectrum of 30% methanolic solution of ALP (5 × 10^?5 M) at pH 6.5 (Mclivaine buffer) was run between 200 and 380 nm. The absorption spectrum of ALP exhibits two peaks with a λ_max. at 255 nm and a weak band at 325 nm. When the spectra of the drug were run at varying pH in the region 200–380 nm, one isosbestic point at 290 nm was observed, which indicated the presence of two ionic conditions in solution. The complex exhibited an absorption maximum at 265 nm and emission peak at 520 nm with respect to the excitation wavelength of 325 nm. The spectrophotometric method was found to be linear in 8.0–17.0 μg ml^?1 range with detection limit of 13.520 μg ml^?1, while 0.05–9.5 μg ml^?1 range was with detection limit of 1.048 × 10^?2 μg ml^?1 by spectrofluorimetric method. The mean percentage recovery of the added quantity was found to be 99.54 (spectrophotometric method) and 100.22 (spectrofluorimetric method) and the %RSD are lower than 0.478 and 0.296 determined spectrophotomerically and spectrofluorimtrically, respectively. This indicates that the proposed method is accurate. The apparent ionization constant of ALP was found to be 9.29. The spectra, experimental conditions were set followed by determination stoichiometry, stability constant and thermodynamic parameters of the As(III), Co(II), Ni(II), and Zn(II) complexes with ALP at pH 6.5. The proposed methods have been successfully applied to the assay of ALP in tablets and the results were statistically evaluated.     

Ab initio SCF calculations of the linear infinite chain of LiH according to the pseudo-lattice method

The pseudo-lattice (PL) method has been reformulated for ab initio self-consistent-field (SCF) calculations. The translational symmetries of infinite systems have been applied to the finite model chain by manipulating all the intramolecular and intermolecular Fock matrices. The nuclear repulsion energy has been corrected accordingly. The method has been tested for the linear chain of lithium hydride under the constraint of equidistance between all neighboring lithium and hydrogen atoms. The calculated results of the infinite chain have been compared with those of finite chains of lithium hydride under the same geometric constraint. The equilibrium geometries, band structures, intermolecular stabilization energies and potential curves have been studied. It is found that the infinite systems cannot be described by considering only first nearest neighbor interactions, and the intermolecular interactions must be considered at least up to third nearest neighbors in order to obtain accurate value of force constant of infinite systems. We can conclude from band structures of infinite chains that the boundary effect of the finite model chain is effectively removed by the PL method.     

Closed-packed lattice model for polymer solution systems considering the chain length dependence effect: Correlating LLE,VLE, and gel swelling behaviors using identical interaction energy parameters

We propose a new Helmholtz energy of mixing equation following the original Flory–Huggins (F–H) closed-packed lattice model. Also, to overcome F–H mean-field approximation, we introduce new universal constants to consider chain length dependence of polymer in solvent and consider specific interactions to describe strongly interacting polymer systems. Our proposed model successfully describes liquid–liquid equilibria (LLE) for binary polymer–solvent systems using identical interaction parameters which do not depend on the polymer molecular weight. We also describe vapor–liquid equilibria (VLE) for polymer/solvent systems and swelling equilibria of thermosensitive hydrogel systems using the same energy parameters obtained from LLE calculations.     

Total selenium and selenomethionine in pharmaceutical yeast tablets: assessment of the state of the art of measurement capabilities through international intercomparison CCQM-P86

Results of an international intercomparison study (CCQM-P86) to assess the analytical capabilities of national metrology institutes (NMIs) and selected expert laboratories worldwide to accurately quantitate the mass fraction of selenomethionine (SeMet) and total Se in pharmaceutical tablets of selenised-yeast supplements (produced by Pharma Nord, Denmark) are presented. The study, jointly coordinated by LGC Ltd., UK, and the Institute for National Measurement Standards, National Research Council of Canada (NRCC), was conducted under the auspices of the Comité Consultatif pour la Quantité de Matière (CCQM) Inorganic Analysis Working Group and involved 15 laboratories (from 12 countries), of which ten were NMIs. Apart from a protocol for determination of moisture content and the provision of the certified reference material (CRM) SELM-1 to be used as the quality control sample, no sample preparation/extraction method was prescribed. A variety of approaches was thus used, including single-step and multiple-step enzymatic hydrolysis, enzymatic probe sonication and hydrolysis with methanesulfonic acid for SeMet, as well as microwave-assisted acid digestion and enzymatic probe sonication for total Se. For total Se, detection techniques included inductively coupled plasma (ICP) mass spectrometry (MS) with external calibration, standard additions or isotope dilution MS (IDMS), inductively coupled plasma optical emission spectrometry , flame atomic absorption spectrometry and instrumental neutron activation analysis. For determination of SeMet in the tablets, five NMIs and three academic/institute laboratories (of a total of five) relied upon measurements using IDMS. For species-specific IDMS measurements, an isotopically enriched standard of SeMet (⁷⁶Se-enriched SeMet) was made available. A novel aspect of this study relies on the approach used to distinguish any errors which arise during analysis of a SeMet calibration solution from those which occur during analysis of the matrix. To help those participants undertaking SeMet analysis to do this, a blind sample in the form of a standard solution of natural abundance SeMet in 0.1 M HCl (with an expected value of 956 mg kg⁻¹ SeMet) was provided. Both high-performance liquid chromatography (HPLC)–ICP-MS or gas chromatography (GC)–ICP-MS and GC-MS techniques were used for quantitation of SeMet. Several advances in analytical methods for determination of SeMet were identified, including the combined use of double IDMS with HPLC-ICP-MS following extraction with methanesulfonic acid and simplified two-step enzymatic hydrolysis with protease/lipase/driselase followed by HPLC-ICP-IDMS, both using a species-specific IDMS approach. Overall, satisfactory agreement amongst participants was achieved; results averaged 337.6 mg kg⁻¹ (n = 13, with a standard deviation of 9.7 mg kg⁻¹) and 561.5 mg kg⁻¹(n = 11, with a standard deviation of 44.3 mg kg⁻¹) with median values of 337.6 and 575.0 mg kg⁻¹ for total Se and SeMet, respectively. Recovery of SeMet from SELM-1 averaged 95.0% (n = 9). The ability of NMIs and expert laboratories worldwide to deliver accurate results for total Se and SeMet in such materials (selensied-yeast tablets containing approximately 300 mg kg⁻¹ Se) with 10% expanded uncertainty was demonstrated. The problems addressed in achieving accurate quantitation of SeMet in this product are representative of those encountered with a wide range of organometallic species in a number of common matrices. Figure Looking into the quantitative speciation of selenium in pharmaceutical supplements Photo courtesy of LGC.     

Different sample stacking strategies for the determination of ertapenem and its impurities by micellar electrokinetic chromatography in pharmaceutical formulation

Ertapenem, a Group 1 carbapenem, is most recently introduced into the market. It is a beta-lactam antibiotic that possesses a broad antibacterial spectrum including common community-acquired Gram-positive and Gram-negative aerobic and anaerobic pathogens, but low activity against some nosocomial pathogens such as Pseudomonas aeruginosa, Acinetobacter spp., enterococci and methicillin-resistant staphylococci. The elaborated method of micellar electrokinetic chromatography (MEKC) of ertapenem separation from its impurities was successfully performed using normal stacking mode (NSM) and stacking with reverse migrating micelles (SRMM), followed by UV absorption detection at 214 nm. The best results were obtained with 60mM sodium dihydrogen phosphate and 20mM boric acid buffer pH 6.0, as background electrolyte. Uncoated fused-silica capillary and neutral-coated capillary with normal and reverse polarity, and voltage values of +18 and -12 kV, respectively, were used throughout the investigation. Sodium dodecyl sulfate was employed as the pseudostationary phase. A comparison of applied techniques, including sensitivity enhancement factors and limits of detection (LOD), is presented. The optimized method was validated in terms of linearity, accuracy and precision. Comparable LOD was obtained using both stacking methods (0.3 microg/mL) but better efficiency of ertapenem peak was obtained using NSM. Under the optimum stacking conditions, about 183-4.75-fold and 1289-4.07-fold improvements in peak areas were obtained for NSM and SRMM, respectively, compared to the usual hydrodynamic sample injection (10s). The reproducibility, expressed by relative standard deviations (RSD) of the migration times, for NSM was about 0.96-1.25 and for SRMM was 0.32-0.45. The RSD of corrected peak areas, for NSM was about 1.07-8.14 and for SRMM was 0.74-8.12. The difference in separation time between the two techniques was not obvious. Satisfactory separation was possible after less than 11min of electrophoresis. The evaluated MEKC method was applied in the analysis of medicinal product containing ertapenem: Invanz-ertapenem for injection.     

An overview of the applications of capillary electrophoresis to the analysis of pharmaceutical raw materials and excipients

Summary The use of capillary electrophoresis for the separation and quantitation of a range of pharmaceutical raw materials and excipients is reviewed. Capillary electrophoresis is shown to be a useful and versatile technique for a large number of applications. Features of the various methods include simplicity, detection of poor chromatophore species by extensive use of indirect UV detection or direct absorbance at low wavelengths, minimal operating costs and generation of high quality retrievable raw data. Specific novel examples described include separations of lactose, flavouring agents, inorganic salts, lecithin constituents, a range of organic acids, benzylalkonium chloride components, sodium lauryl sulphate, and the quality of input water. It is concluded that the versatility of CE will ensure that it is increasingly used in the analysis of pharmaceutical raw materials and excipients.     

Evaluation of a multiarray system for pharmaceutical analysis by microemulsion electrokinetic chromatography

A multiplexed capillary electrophoresis (CE) system equipped with 96 channels was evaluated for high-throughput screening in drug discovery by microemulsion electrokinetic chromatography (MEEKC). Method transfer from a single channel to a multichannel CE system is described. Loss of efficiency and reduced migration times could be elucidated to the poor efficacy in Joule heat dissipation by forced air cooling in the multiarray system compared to liquid cooling in the single channel instrument. On the other hand, only 48 channels could actually be used because of the maximum total current of 3 mA. Precision data remained below 8% and 9% for migration times and peak areas, respectively. Some UV-detector cross-talk interference between neighboring capillary channels was noted. Impurities at 0.5% compared to the main peak (100%) could be detected with the multiplexed system which is 10 times lower compared to the single capillary system. Higher efficiency and improved figures of merit (absolute sensitivity and no cross-talk interferences) were obtained by using an array of only 24 capillaries.     

Studies on the construction of the 2-isooctyl side chain in 17-azasteroids

Summary The transformations of (20R)- and (20S)-3-hydroxy-16-oxo-24-nor-17-azachol-5-eno-23-nitriles towards the 17-aza analogue of cholesterol are described. Attempts of a direct addition of a four carbon atom fragment to nitriles were unsuccessful. Alternately, nitriles were transformedvia carboxylic acids, methyl esters and primary alcohols into iodides. The coupling reaction of (20S)-iodide with (i-Bu)₂CuLi afforded the desired product in low yield but failed in the case of the 20R epimer.

---

Untersuchungen zum Aufbau der 2-Isooctyl-Seitenkette in 17-Azasteroiden

Zusammenfassung Die Umsetzungen von (20R)- und (20S)-3-Hydroxy-16-oxo-24-nor-17-azachol-5-eno-23-nitril zum 17-aza-Analogon von Cholesterin werden beschrieben. Versuche einer direkten Addition eines 4-Atom-Fragments an Nitrile verliefen erfolglos. Als Ausweg wurden die Nitrile über Carbonsäuren, Methylester und primäre Alkohole zu den lodiden umgesetzt. Die Kupplungsreaktion von (20S)-lodid mit (i-Bu)₂CuLi ergab das gewünschte Produkt in niedriger Ausbeute; das (20R)-Epimere reagierte nicht.

     

Development and validation of a capillary electrophoresis method with ultraviolet detection for the determination of the related substances in a pharmaceutical compound

A capillary electrophoresis (CE) method was successfully developed to quantify the impurity profile of a new substance of pharmacological interest: LAS 35917. CE method was developed in order to separate the chloromethylated, monomethylated and hydroxylated impurities (molecules with very similar chemical structures) having the three coelution in the reversed-phase LC method initially established. Taking into account the structure of the impurities of LAS 35917, separation by conventional liquid chromatography (LC) methods would be longer and tedious than separation by CE, which is an appropriate and versatile technique giving easier and quicker methods. Among the three potential impurities mentioned of LAS 35917, two are due to the synthesis route of this drug, and the third arises from degradation. These drug-related impurities were separated using a capillary of 56 cm of effective length and 50 microm I.D., a 60 mM tetraborate buffer, at pH 9.2, and a positive voltage of 20 kV. The optimised CE method was preliminary validated with regard to specificity, linearity, limits of detection and quantitation, repeatability and solution stability. The method allows the detection and quantitation of impurities above 0.04 and 0.08% level, respectively. All three related substances were separated, detected and quantified from their parent drug in the analysis of real samples of LAS 35917, stressed or not stressed, with this simple and fast CE method.     

The influence of chain rigidity on the thermal properties of some novel random copolyethersulfones

Some random low molar mass (M_n ≈ 9000 g mol⁻¹) poly(ethersulfoneethersulfone)/poly(ethersulfoneethersulfonebiphenylsulfone) P(ESES)/P(ESESBS) copolymers, with various (25%, 50% and 75%) ESESBS units contents, were synthesized to obtain compounds with higher chain rigidity than PES. The thermal characterization of the prepared copolymers, as well as that of corresponding P(ESES) and P(ESESBS) homopolymers, was performed, and all investigated parameters showed strong dependence on polymer composition.The glass transition temperature (T_g) was calorimetrically determined by DSC technique, and the obtained values increased linearly as function of ESESBS units percentage, thus indicating an increasing chain rigidity.Degradations were carried out in dynamic heating conditions, from 35 °C to 700 °C, in both flowing nitrogen and static air atmosphere, and the characteristic parameters of degradation were determined in order to draw useful information about the overall thermal stability of the studied compounds. The apparent activation energy of degradation (E_a) was obtained by the Kissinger method, and the values found increased linearly as a function of ESESBS content, while the temperature values at 5% mass loss (T_5%) showed an opposite linear trend. The results are discussed and interpreted.     

Sequential injection method for the direct spectrophotometric determination of bismuth in pharmaceutical products

A spectrophotometric method is reported for the determination of bismuth in pharmaceutical products using sequential injection analysis. Methylthymol blue (MTB) was used as a color forming reagent and the absorbance of the Bi(III)-MTB complex was monitored at 548 nm. The various chemical and physical variables that affected the reaction were studied. A linear calibration graph was obtained in the range 0.0-75.0 mg l⁻¹ Bi(III) at a sampling frequency of 72 h⁻¹. The reagent consumption was considerably reduced compared to conventional flow injection systems, as only 150 μl of MTB were consumed per run. The precision was very satisfactory (s_r=0.5%, at 50.0 mg l⁻¹ Bi(III), n=12) and the limit of detection, c_L, was 0.250 mg l⁻¹. The developed method was applied successfully to the analysis of various pharmaceutical products containing Bi(III). The relative errors e_r, were <1.5% in all cases and were evaluated by comparison of the obtained results with those found using atomic absorption spectrometry as the reference method.     

Development of a stability indicating HPTLC method for the estimation of olanzapine in pharmaceutical dosage forms

We report herein an accurate, precise, and economical stability indicating high performance thin layer chromatographic (HPTLC) method developed to assess the safety of olanzapine in pharmaceutical formulations. Olanzapine was subjected to forced degradation studies to assess the effect of environmental conditions on its stability. Stress conditions such as hydrolysis under acidic and alkaline environment, degradation and oxidation by heat, light and air were used to study the stability of olanzapine. Mobile phase comprising of toluene: methanol (5:5 v/v) and aluminum plate pre-coated with silica gel 60 F₂₅₄ as a stationary phase were used for the development of chromatogram by HPTLC technique. Densitometric analysis of olanzapine carried out at 297 ​nm gave sharp symmetrical peak with R_f value of 0.50 and a satisfactory baseline resolution for all components. The drug was found to undergo degradation under acidic, alkaline and oxidative conditions. A single distinct peak in acidic and alkaline media while two peaks obtained as a result of oxidative degradation were well resolved along with the parent drug. The degradation products and parent drug showed significantly different R_f values. The developed HPTLC method gave quick and reproducible results for the olanzapine content in the tablets. The mean recoveries were 100.75% which confirms accuracy of the proposed method. The method was further validated for specificity, ruggedness and robustness. Based on the results, it can be suggested that the developed HPTLC method is quite efficient in separating the olanzapine from its degradation products; hence it can be used by pharmaceutical industries and regulatory bodies for the routine analysis of olanzapine in various pharmaceutical dosage forms.     

An affordable method for the simultaneous determination of the most studied pharmaceutical compounds as wastewater and surface water pollutants

There is still an increasing need of knowledge about the presence of pharmaceuticals in the environment in many countries. To contribute to the improvement of this knowledge it should be useful to get not only more reliable methods, but also analytical methods that do not require expensive equipment and, consequently, could be used even in the less developed areas. In the present work, a novel analytical method for the simultaneous determination of several priority pharmaceuticals, as aquatic media pollutants, in wastewater and surface water is reported. The method involves sample treatment by SPE, followed by LC with diode array and fluorescence detection. Parameters that affect the efficiency of the SPE step such as elution solvents, sample pH and cartridge sorbents were evaluated and optimized. The best results were obtained using acetone as elution solvent, acidifying samples to pH 2 and employing Oasis HLB as SPE sorbent. Recoveries of the pharmaceuticals from influent and effluent wastewater and surface water samples were in the range from 61.4 to 123%. LODs were in the range of 0.001–0.323 μg/L and LOQs were between 0.020 and 1.078 μg/L.     

Testing the performance of pure spectrum resolution from Raman hyperspectral images of differently manufactured pharmaceutical tablets

Chemical imaging is a rapidly emerging analytical method in pharmaceutical technology. Due to the numerous chemometric solutions available, characterization of pharmaceutical samples with unknown components present has also become possible. This study compares the performance of current state-of-the-art curve resolution methods (multivariate curve resolution-alternating least squares, positive matrix factorization, simplex identification via split augmented Lagrangian and self-modelling mixture analysis) in the estimation of pure component spectra from Raman maps of differently manufactured pharmaceutical tablets. The batches of different technologies differ in the homogeneity level of the active ingredient, thus, the curve resolution methods are tested under different conditions. An empirical approach is shown to determine the number of components present in a sample. The chemometric algorithms are compared regarding the number of detected components, the quality of the resolved spectra and the accuracy of scores (spectral concentrations) compared to those calculated with classical least squares, using the true pure component (reference) spectra. It is demonstrated that using appropriate multivariate methods, Raman chemical imaging can be a useful tool in the non-invasive characterization of unknown (e.g. illegal or counterfeit) pharmaceutical products.