国产非晶磁芯应用于感应加速组元的可行性研究

介绍了国产非晶合金应用于感应加速组元的可行性研究的初步结果.采用国产1K101型铁基非晶合金(FeSiB)带材,研制了非晶磁芯,并利用加速腔(或实验腔)对研制的非晶磁芯的磁性能、绝缘性能和稳定性等方面进行了研究.高压单脉冲实验可获得脉冲幅度为240kV、脉冲前沿为17璐(10%-90%)、脉冲平顶为72ns(±1%)的单脉冲;高压猝发三脉冲实验可获得前沿35ns、脉冲平顶60ns的三脉冲,磁芯的有效平均磁密跳变为1.41T.耐压实验研究中,得到了电压幅值为282kV的三脉冲.非晶磁芯的性能稳定,满足感应加速组元对磁芯性能的要求.     

脉冲压缩电路磁开关动态特性

提出在典型一阶磁脉冲压缩电路的基础上,测取磁芯在实际工作条件下的动态磁滞回线和饱和磁导率等磁参数,再根据所获得的动态参数指导磁开关设计,进行一阶磁压缩实验。实验选取国内外被广泛应用的非晶磁芯和纳米晶磁芯进行测试,根据实测动态磁参数设计磁开关。实测结果表明:用国产非晶磁芯做磁开关可得到上升沿73 ns、电压幅值28.3 kV、半高宽为503 ns的脉冲,用日本产的纳米晶磁芯做磁开关可得到上升沿30 ns、电压幅值28.4 kV、半高宽为193 ns的脉冲。     

猝发双脉冲直线感应加速器组元研究

 在原单脉冲直线感应加速器（LIA）组元的基础上，利用电缆延时和电缆反射两种方式获得了间隔500～1 000 ns的猝发双脉冲输出。在感应加速腔上进行了双脉冲实验，获得了幅度大于200 kV、前沿小于35 ns、平顶大于60 ns的双脉冲加速电压波形。两种方式中第一个脉冲的前沿和幅度都达到了原单脉冲组元的水平，表明加速腔负载的变化对波形没有明显影响，但由于电缆对波形的损耗，第二个脉冲的幅度和前沿比第一个脉冲略差。可以利用水介质传输线来代替长电缆，减小传输线的长度及其对波形的损耗。两个脉冲间的幅度差异可以通过改变长电缆的阻抗来调节。实验表明，通过这两种猝发双脉冲的产生方式并结合加速腔磁芯的改进，可简单高效地完成原单脉冲LIA的双脉冲改造。     

猝发双脉冲直线感应加速器组元研究

在原单脉冲直线感应加速器（LIA）组元的基础上，利用电缆延时和电缆反射两种方式获得了间隔500～1 000 ns的猝发双脉冲输出。在感应加速腔上进行了双脉冲实验，获得了幅度大于200 kV、前沿小于35 ns、平顶大于60 ns的双脉冲加速电压波形。两种方式中第一个脉冲的前沿和幅度都达到了原单脉冲组元的水平，表明加速腔负载的变化对波形没有明显影响，但由于电缆对波形的损耗，第二个脉冲的幅度和前沿比第一个脉冲略差。可以利用水介质传输线来代替长电缆，减小传输线的长度及其对波形的损耗。两个脉冲间的幅度差异可以通过改变长电缆的阻抗来调节。实验表明，通过这两种猝发双脉冲的产生方式并结合加速腔磁芯的改进，可简单高效地完成原单脉冲LIA的双脉冲改造。     

多脉冲励磁下铁氧体及非晶磁环的磁特性

感应脉冲加速器的磁芯通常为铁氧体或非晶材料,而感应腔磁芯在工作脉冲下的磁性能是决定感应加速脉冲波形好坏的重要因素。搭建了低压多脉冲实验平台对铁氧体和非晶小磁环分别进行MHz重复频率的多脉冲励磁,对励磁线圈上的电压电流波形进行监测,绘制了多脉冲励磁下磁环的磁化曲线,并结合含磁芯线圈动态电感量的递推公式计算出磁环在多脉冲励磁过程中磁导率的变化曲线;在高压三脉冲实验平台上对铁氧体磁芯和非晶磁芯实验感应腔进行了高压三脉冲实验,得到的磁芯多脉冲磁化规律与低压实验的结果一致。最后对两种磁环在多脉冲励磁下的磁性能差异进行了对比分析。     

双脉冲电子直线感应加速器实验研究

 Mini-LIA为MHz重复频率双脉冲电子直线感应加速器,由双脉冲功率系统、热阴极电子枪注入器及金属玻璃磁芯感应加速腔等组成。在此平台的实验获得了数百ns间隔（即MHz重复频率）的双脉冲高压,每个脉冲幅值达到80 kV,脉冲半高全宽为80 ns;在感应腔加速间隙处测得双脉冲加速电场;在加速器出口处测量得到流强约1.1 A的双脉冲电子束流。实验结果表明：利用硅堆隔离汇流装置可实现MHz重复频率的双脉冲高压,金属玻璃磁芯感应加速腔和六硼化镧热阴极电子枪均适合MHz重复频率双脉冲工作方式。     

磁芯材料脉冲间叠加复位研究

 介绍了通过反向叠加长脉冲的方法,在双脉冲间隔小于1 μs的情况下对直线感应加速器磁芯进行的脉冲间复位实验,复位后波形幅度得到了明显改善,在最大伏秒值280 kV×100 ns的单脉冲感应腔上得到了两个伏秒值为200 kV×100 ns的感应脉冲。实验表明：当主脉冲脉宽小于100 ns,间隔大于500 ns时,采用脉冲间叠加复位的方法,将主脉冲叠加在一个反向的长脉冲上（脉宽大于10 μs,最大幅度约为主脉冲的20%）形成正负脉冲串,能有效提高感应加速腔磁芯的利用率,且对感应主脉冲没有明显影响,使单脉冲直线感应加速器的多脉冲改造成为可能。     

0.1 Hz 800 kA驱动源模块研制北大核心CSCD

介绍了面向Z箍缩驱动聚变裂变混合堆(Z-FFR)能源的重复频率800kA快上升沿的线性变压器驱动源(LTD)模块的设计和测试。LTD模块由34组RLC电路组成,每组包含2台100kV/40nF脉冲电容器、1个多间隙气体开关和非晶磁芯。研制的模块可以在匹配水电阻负载上以0.1 Hz的重复频率输出上升沿约100ns的800kA的电流脉冲。采用了一个高压触发信号来触发整个模块的新触发方式,将外触发信号通过模块内布置的角向传输线等网络同时到达并触发所有的高压开关,实验结果表明采用一路140kV、25ns前沿的触发脉冲可以可靠地触发整个模块。为了保证LTD模块每10s输出一个80kV/800kA的电流脉冲,非晶磁芯的去磁复位采用了一个5.2kA、脉宽30!s的电流脉冲,其运行频率为0.1 Hz。模块采用的多间隙气体开关运行寿命超过10 000次,其抖动小于3ns。     

全固态激励小型TEA CO_2激光器的研制

基于国产非晶态合金磁芯,研制了采用可控硅开关、脉冲升压变压器、以及两级磁脉冲压缩网络的全固态激励电路系统,并且应用于放电体积为29 cm3,工作气压为100 kPa的电晕预电离小型TEA CO2激光器。讨论了提高系统能量传输效率和减小系统体积的设计方法,并且测量了系统的工作性能以及各部分的能量损失。实验结果表明:磁脉冲压缩网络的能量传输效率大于83%,全固态激励系统的总效率大于75%;连接激光器负载时,输出脉冲的电压峰值约为22 kV,电流上升时间约为100 ns;得到了脉冲能量109 mJ,宽度70ns的激光输出,激光器整体效率约为3.3%。在目前的封离体积与气体循环方式限制下,激光器最大重复频率约为100 Hz,而激励电路部分可以达到400 Hz的工作频率。     

低剩磁磁芯自复位能力研究

 在MHz重复频率的高压多脉冲下,如何在脉冲间隔对磁芯进行快复位是高压多脉冲感应加速腔研制的关键问题。对低剩磁磁芯在脉冲励磁后磁通量密度的自恢复能力及其影响因素进行了实验研究和理论分析,证实了利用低剩磁磁芯的自恢复能力来实现在高压多脉冲下重复利用磁芯伏秒值的可能。实验证明：在选用合适的材料及工作电路后,磁芯在脉冲励磁后自复位到剩磁处的时间可小于500 ns,可稳定地工作在MHz重复频率的高压多脉冲环境下。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.