热处理温度对沥青基硼氮共掺杂多孔炭结构与电化学性能的影响

以煤液化沥青质为碳源、硝酸为氮源、硼酸为硼源和造孔剂制备硼氮共掺杂多孔炭,研究了热处理温度对其孔结构和表面性质的影响,测试了产品作为超级电容器电极材料的性能.用X射线衍射(XRD)、拉曼光谱、扫描电镜(SEM)、透射电镜(TEM)、N2吸附、元素分析、电感耦合等离子体发射光谱(ICP-AES)、X射线光电子能谱(XPS)、电化学工作站等对材料的结构、组成及电化学性能进行了表征.结果表明:随着热处理温度的升高,产品的石墨化程度逐渐升高;比表面积、总孔容呈先增加后减小的趋势;氮含量随着热处理温度的升高逐渐降低,而硼含量则随着热处理温度的升高逐渐增加;材料的比电容随着热处理温度的升高先逐渐增加后减小.其中900°C热处理的样品比表面积达到1103 m2·g-1,总孔容为0.921 cm3·g-1,氮含量为5.256%(w),硼含量为1.703%(w),在6 mol·L-1KOH电解液中当电流密度为100 mA·g-1时质量比电容为349 F·g-1;而经过1000°C热处理的样品表现出最好的倍率特性,电流密度从100 mA·g-1增加到10A·g-1时比电容保持率为75%.     

Synthesis and characterization of nanocrystalline tin oxide by sol–gel method

Nanocrystalline SnO₂ particles have been synthesized by a sol–gel method from the very simple starting material granulated tin. The synthesis leads a sol–gel process when citric acid is introduced in the solution obtained by dissolving granulated tin in HNO₃. Citric acid has a great effect on stabilizing the precursor solution, and slows down the hydrolysis and condensation processes. The obtained SnO₂ particles range from 2.8 to 5.1 nm in size and 289–143 m² g⁻¹ in specific surface area when the gel is heat treated at different temperatures. The particles show a lattice expansion with the reduction in particle size. With the absence of citric acid, the precursor hydrolyzes and condenses in an uncontrollable manner and the obtained SnO₂ nanocrystallites are comparatively larger in size and broader in size distribution. The nanocrystallites have been characterized by means of TG-DSC, FT-IR, XRD, BET and TEM.     

Synthesis and spectral characterization of Cu(II) complexes of some thio-Schiff bases of acyl pyrazolone analogues

A series of tridentate pyrazolone-based thio-Schiff bases were synthesized by the interaction of 4-acyl/aroyl pyrazolones with thiosemicarbazide in an ethanolic medium. All of these ligands were characterized on the basis of elemental analysis, infrared (IR), ¹H- and ¹³C-NMR data. Nuclear magnetic resonance (NMR) suggests the amine-one form of ligand in solution at room temperature. Copper Schiff-base complexes, [Cu(L)(H₂O)], have been prepared by the interaction of the aqueous solution of copper sulfate pentahydrate with hot ethanolic solution of the appropriate ligand. The resulting complexes have been characterized by elemental analysis, metal content determination, molar conductance, fast atom bombardment mass spectra, magnetic measurements, thermogravimetric analysis (TGA), IR, and electronic spectral studies. Thermal stability, heat capacity, and activation energy of thermal degradation for these complexes were determined by TGA, differential thermal analysis, and differential scanning calorimetry. Suitable structures are proposed for these complexes.     

Synthesis, structural and thermal characterization of metaphosphatenickel(II) salt

A new inorganically template metaphosphate of Ni(II) complex has been synthesized and characterized by different measurements such as DSC, FT-IR, C?CH?CN?CS, X-RD and ICP-AES. Differential scanning calorimeter (DSC) elucidated negative specific heat of the system and has used to evaluate some thermodynamical constants like specific heat, enthalpy and entropy of that system. The specific heat capacity of the system is measured in atmospheric O₂ at heating rate of 278 and 283?K?min^?1. The specific heat is found both positive and negative at 278?K?min^?1.     

Blends of Aromatic Polyethers Bearing Polar Pyridine Units and Their Evaluation as High Temperature Polymer Electrolytes

Aromatic polyethers containing polar pyridine units in the main chain have been synthesized using different difluoride monomers. Copolymers of 2,5-(4′,4″dihydroxy biphenyl)-pyridine and 3,3′,5,5′-tetramethyl-[1,1′-biphenyl]-4,4′-diol with bis(4-fluorophenyl) sulfone or phenyl phosphine oxide difluoride or decafluorobiphenyl (PTMPySF, PTMPyPO, PTMPyDF) were synthesized. These polymeric structures despite their common structural characteristics, showed totally different behavior in terms of solubility and acid doping ability. Blends of these copolymers have been prepared in order to be evaluated in terms of fuel cell relevant parameters like acid doping ability and conductivity. In most cases flexible membranes were obtained by solution casting. The acid doping ability was controlled based on the blend constituents and composition. The doped membranes exhibited high conductivity values, in the range of 10⁻³ S/cm at room temperature which is increased at 2.5 × 10⁻² S/cm at temperatures up to 180 °C.     

Spectral properties and G-quadruplex DNA binding selectivities of a series of unsymmetrical perylene diimides

A series of new unsymmetrical perylene diimides have been synthesized to investigate their binding selectivities to G-quadruplex DNA structure, a unique four-stranded DNA motif, which is significant to the regulation of telomerase activity. The structures of the perylene diimides have been characterized by IR spectrophotometer, ¹H NMR, ¹³C NMR, MS, TGA and time-resolved instruments. Spectrochemical behaviors have been investigated by visible absorption and fluorescence emission spectra. The spectral characterization of the compounds has been investigated in five common organic solvents of different polarity and in water (in 170 mM phosphate buffer at pH 6). Marked red shifts of absorbance and fluorescence emission bands of the compounds in aqueous solution are compared with the other organic solutions. The fluorescence quantum yields are determined low in more polar solvents and also calculated to be about less than about 0.05 in aqueous solution because of the aggregation effects. Photodegradation rate constants (k_p) of the synthesized compounds have been compared under xenon lamp irradiation in acetonitrile solution.Binding abilities of the synthesized perylene diimides to different form of DNA strands have been investigated by visible absorption and fluorescence spectroscopy in the phosphate buffer solutions. Also, pH-dependent aggregation and G-quadruplex DNA binding selectivity of these ligands have been compared. Among these ligands, N-(2,6-diisopropylphenyl)-N′-(4-pyridyl)-perylene-3,4,9,10-tetracarboxylic diimide (PYPER) has been found to be the most selective interactive ligand for G-quadruplex formed in the G4′-DNA structure. PYPER has shown a significant selectivity to G4′-DNA which is comprised of d(TTAGGG) repeats, known as human telomeres, in the phosphate buffer at pH 6. The absorption maximum of the PYPER/G4′-DNA complex has given bathochromic shift of 7 nm with respect to the absorption maximum of DNA-free solution of PYPER in phosphate buffer at pH 6. Fluorescence quenching experiments between PYPER and G4′-DNA show that PYPER demonstrates about a 9.3-fold selectivity for binding to G4′-DNA versus ds-DNA base pairs with the bimolecular rate constant of 0.95 × 10¹² M⁻¹ s⁻¹.     

二氧化钛柱撑层状氧化锰微孔材料的合成及表征

Na型层状锰氧化物于0.1 mol/L HCl 溶液中离子交换制得前驱体H型层状锰氧化物. H型层状锰氧化物在十二胺乙醇溶液中反应得到层间距为2.62 nm的中间产物——十二胺插入的层状锰氧化物, 该中间产物在异丙醇钛和乙醇的混合溶液中溶剂热处理得到层间距为1.24 nm的钛酸柱撑层状锰氧化物. 在300 ℃条件下经2 h焙烧得到二氧化钛铸型氧化锰微孔材料. 应用XRD, DSC-TGA, SEM, TEM, IR, 氮气吸附实验及元素分析进行了不同阶段所得试样的分析表征. 结果表明十二胺分子在锰氧层间的最大插入量为2.2 mmol/g, 异丙醇钛分子的置换插入生成了组成为Mn_7.00Ti_1.74O_23.3(C₁₂H₂₅NH₂)_0.52•1.93H₂O的铸型层状锰氧化物. 300 ℃焙烧处理所得二氧化钛铸型氧化锰微孔材料的比表面积为140 m²/g.     

On the heat of solution of polymer with solvent: Polydimethylsiloxane–solvent systems

Heats of mixing and excess volumes at infinite dilution have been obtained at 25°C. for polydimethylsiloxane or its lower oligomers in various solvents by using a twin conduction microcalorimeter and from the pycnometric specific volumes. From those values, excess energies ΔE^M_v at constant volume have been determined. The prediction on intramolecular conformation contributions to the heat of solution as proposed by Bianchi has been evaluated by the values of ΔE^M_v. The heat of solution in the polymer–solvent systems was interpreted by the expression for ΔE^M_v derived from the Van Laar-Hildebrand work on simple liquid mixtures with the solubility parameters of polymers obtained from indirect measurements. The values of conformational intramolecular energy change calculated from dilute solution properties were difficult to rationalize with our results. Our present results suggest that systems in a nonideal state can not be distinguished for certain from those in the ideal state. This conclusion based on apparent values does not deny the possible effect of the conformational energy change.     

Thermodynamic Properties of Peptide Solutions. Part 17. Partial Molar Volumes and Heat Capacities of the Tripeptides GlyAspGly and GlyGluGly,and Their Salts K[GlyAspGly] and Na[GlyGluGly] in Aqueous Solution at 25 °C

The partial molar volumes, V^o₂, and partial molar heat capacities, C_p,2^o, at infinite dilution have been determined for the two tripeptides glycylaspartylglycine (glyaspgly) and glycylglutamylglycine (glyglugly), and also for their salts K[glyaspgly] and Na[glyglugly], in aqueous solution at 25 °C. The ionization constants at 25 °C for the aspartyl and glutamyl side-chains have also been determined. These new thermodynamic results have been combined with literature data for electrolytes to obtain the volume and heat capacity changes upon ionization of the acidic side-chains of the peptides. The results are compared with those for other carboxylic acid systems. The partial molar heat capacities and volumes have also been used to calculate the contributions of the acidic amino acid side-chains to the thermodynamic properties.     

Partial molal heat capacities of sodium perchlorate in N,N-dimethylformamide from 10 to 75°C

Enthalpies of solution of NaClO₄ have been measured calorimetrically in the aprotic solvent N,N-dimethylformamide at several temperatures ranging from 5 to 80°C. The data have been extrapolated to infinite dilution to obtain standard enthalpies of solution. The integral enthalpy of solution method was used to evaluate the standard partial molal heat capacity c _p2 ^° of NaClO₄ in N,N-dimethylformamide as a function of temperature. This function is almost temperature invariant in N,N-dimethylformamide, in contrast to its complex behavior in aqueous and methanolic solutions. This suggests that ionic heat capacities are extremely sensitive to the structure of solutions and that this function can be used as a probe for studying the structure of electrolytic solutions. The complex temperature dependence of c _p2 ^° in water and methanol can be explained in terms of the decreased hydrogen bonding and dielectric constant of the solvents at the higher temperatures. The data show that one must be cautious in interpreting single-temperature heat capacities of transfer between solvents.This paper was taken from the work submitted by Shuya Chang to the Graduate School of the University of Miami, in partial fulfillment of the requirement for the Master of Science Degree.     

Aqueous Synthesis of Triphenylphosphine-Modified Gold Nanoparticles for Synergistic In Vitro and In Vivo Photothermal Chemotherapy

Triphenylphosphine (TPP) surface-functionalized and F-108 Pluronic-stabilized gold nanoparticles (F-108@TPP-AuNPs) have been synthesized through a one-step approach, leading to well-defined (9.6±1.6 nm) and water-soluble nanoparticles by microwave heating an aqueous solution of TPP-Au^ICl in the presence of a Pluronic polymer under basic conditions. TPP release was negligible under physiological conditions, but enhanced significantly at an acidic pH (5.4) mimicking that of a cancer cell. Laser irradiation (532 nm) raised the temperature of an aqueous solution of F-108@TPP-AuNPs to 51.7 °C within 5 min, confirming efficient light-to-heat conversion capabilities without significant photodegradation. TEM confirmed intracellular localization of F-108@TPP-AuNPs in the cytosol, endosomes and lysosomes of HeLa cells. F-108@TPP-AuNPs were well tolerated by HeLa cells and zebrafish embryos at ambient temperatures and became toxic upon heat activation, suggesting synergistic interactions between heat and cytotoxic action by TPP.     

Effects of heat treatment on physicochemical properties of cerium based nickel system

Cerium based nickel catalysts synthesized by impregnation method have been characterized by XRD and TEM techniques. These catalysts can be described as a mixture of nickel oxide and ceria modified by the insertion of a part of nickel in the ceria lattice. The surface and catalytic properties of Ni/Ce mixed oxide solids were determined by nitrogen adsorption at 77 K and catalytic conversion of isopropanol at different temperatures.The results revealed that the heat treatment brought about different modifications in the structural, morphological, surface and catalytic properties of the as synthesized catalysts. From the characterization of the as prepared catalysts, it was concluded that the as prepared catalysts contain highly dispersed NiO, well crystalline NiO and CeO₂ and also Ni–Ce–O solid solution. This treatment led to a slightly increase in the crystallite size of ceria particles. On the other hand, the increase in the heat treatment resulted in an increase in the crystallite size, lattice constant and unit cell volume of nickel oxide. The formation of Ni–Ce–O solid solution with subsequent creation of oxygen vacancies increase as the heat treatment increases. However, the specific surface area, total pore volume and catalytic activity of the investigated system decrease as the preparation temperature increases from 500 to 700 °C. The sintering activation energy of NiO and ceria were found to be 2.8 and 12.7 kJ/mol, respectively.     

The Partial Molar Volume and Heat Capacity of the Glycyl Group in Aqueous Solution at 25^C

The partial molar volumes, V₂ ^{^}, and the partial molar heat capacities, C_p,2 ^{^}, at infinite dilution have been determined for three new peptides of sequence seryl(glycyl)_xglycine, where x=0 to 2, in aqueous solution at 25^{^}C. Values for V₂ ^{^} at 25^°C have also been determined for two neutral peptide derivatives N-acetylglycylglycinamide and N-acetylglycylglycylglycinamide. These V₂ ^°; and C_p,2 ^°; results were used to estimate the partial molar volume and heat capacity of the backbone glycyl group, CH₂CONH, of proteins in aqueous solution at 25^°;C. The results obtained are compared with those calculated using partial molar data for alternative model compounds. The new glycyl group contributions are in excellent agreement with those currently used in our group additivity schemes for the calculation of the partial molar volumes and heat capacities of unfolded proteins.     

A Green Approach for the Synthesis of Silver Nanoparticles Using Root Extract of <Emphasis Type="Italic">Chelidonium majus:</Emphasis> Characterization and Antibacterial Evaluation

In this study, silver nanoparticles (Ag-NPs) have been synthesized using extract of Chelidonium majus root in aqueous solution at room temperature. The root extract was able to reduce Ag⁺ to Ag⁰ and stabilized the nanoparticles Different physico-chemical techniques including UV–Vis spectroscopy, transmission electron microscopy and powder X-ray diffraction (PXRD) were used for the characterization of the biosynthesized Ag-NPs obtained. The surface plasmon resonance band appeared at 431 nm is an evidence for formation of Ag-NPs. TEM imaging revealed that the synthesized Ag-NPs have an average diameter of around 15 nm and with spherical shape. Moreover the crystalline structure of synthesized nanoparticles was confirmed using XRD pattern. Furthermore antimicrobial activities of synthesized Ag-NPs were evaluated against Escherichia coli -ATCC 25922 and Pseudomonas aeruginosa ATCC 2785 bacteria strain.     

Excess heat capacities and excess volumes of binary liquid mixtures of chloroform with cyclic ethers at 298.15 K

Molar excess heat capacities at constant pressure, C^E_p, of binary liquid mixtures chloroform + oxolane, chloroform + 1,3-dioxolane, chloroform + oxane, and chloroform + 1,4-dioxane have been determined at 298.15 K from measurements of volumetric heat capacities in a Picker flow microcalorimeter. A precision of ±0.04 J K^?1 mole^? was achieved by using the stepwise procedure. Experimental molar excess heat capacities are compared with values derived from H^E results at different temperatures. Excess molar volumes, V^E, for the same systems at 298.15 K have been determined by measuring the density of the pure liquids and solutions with a high-precision digital flow densimeter.     

New redox anion receptors based on calix[4]pyrrole bearing ferrocene amide

Two redox anion receptors based on calix[4]pyrrole and ferrocene have been synthesized. The electrochemical investigation revealed that these compounds can be response to the anions with different shifts of Fc/Fc⁺ couple. With the ¹H NMR titration study, the selectivity to F⁻ and AcO⁻ ions in CD₃CN solution was confirmed. The conformations of the mono-aromatic meso-substituted calix[4]pyrroles, which were the synthetical intermediate of the ferrocene based receptors, and their anion complexes in the solid state have also been studied by single X-ray crystallography, and the rationality of the crystal conformations was proved by theoretical study.     

Synthesis,Spectroscopy, Semi‐empirical and Biological Activities of Organotin(IV) Complexes with o‐Isopropyl Carbonodithioic Acid

New organotin(IV) complexes have been synthesized by treating potassium o‐isopropyl carbonodithioate with R₂SnCl₂/R₃SnCl in 1 : 2/1 : 1 M/L ratio. All complexes have been characterized by IR and NMR (¹H, ¹³C) spectroscopy. IR results shows that ligand acts as bidentate which is also confirmed by semi‐empirical study. NMR data reveals four coordinated geometry in solution. Computed positive heat of formation shows that complex 5 is thermodynamically unstable. UV/visible spectroscopy was used to assess the mode of interaction and binding of the complexes with DNA which shows that complex 5 exhibits higher binding constant as compared to complex 3 . In protein kinase inhibition assay, compound 3 was found most active, while other biological activities shows that triorganotin(IV) complexes are biologically more active as compared to diorganotin(IV) complexes.     

Silicon-containing hydroxylapatite nanopowders

Silicon-substituted hydroxylapatite nanopowders containing 0.14–1.4 wt % Si have been synthesized by the heterophase reaction between calcium hydroxide, diammonium hydrogen phosphate, tetraethoxysilane, and water and by precipitation from aqueous solutions of calcium nitrate, diammonium hydrogen phosphate, and tetraethoxysilane. The products have been characterized by specific surface area (S _BET) measurements, X-ray powder diffraction, chemical analysis, and IR spectroscopy. The phase composition of the products depends on the synthesis method. The heterophase reaction yields nanopowders with S _BET = 20–24 m²/g in which the main crystalline phase is silicon-substituted hydroxylapatite. The product synthesized by precipitation from solution has an S _BET of up to 73 m²/g and an increased tricalcium phosphate content, which crystallizes from the amorphous phase during heat treatment.     

Influences of temperature and atmosphere on thermal stability of BaCrO4

In this article, the influences of temperature and atmosphere on thermal stability of BaCrO₄ were investigated. BaCrO₄ powders with an orthorhombic structure were synthesized by a facile aqueous solution route. The synthesized BaCrO₄ products were then heat treated at different atmospheres to evaluate their thermal stability by differential thermal analysis–thermogravimetry (DTA–TG), X-ray photoelectron spectroscopy and X-ray diffraction. BaCrO₄ has a good thermal stability and does not decompose in air up to 1,400 °C. However, the decomposition of BaCrO₄ in vacuum depends mainly upon a two-stage chemical reaction. BaCrO₄ is finally decomposed into BaCr₂O₄ with trivalent Cr³⁺ cations and Ba₃(Cr⁶⁺ Cr⁵⁺)₂O_9?x with both pentavalent Cr⁵⁺ and hexavalent Cr⁶⁺ cations after heat treatments in vacuum.     

Simultaneous determination of phenolic compounds by means of an automated voltammetric “electronic tongue”

Zirconium(IV) selenoiodates have been synthesized under a variety of conditions. The most chemically and thermally stable sample is prepared by adding a mixture of aqueous solutions of 0.1 mol L^–1 potassium iodate and 0.1 mol L^–1 sodium selenite to aqueous solution of 0.1 mol L^–1 zirconium(IV) oxychloride. Its ion-exchange capacity for K⁺ and Pb²⁺ was found to be 3.20 and 2.35 meq g^–1 dry exchanger, respectively. The material has been characterized on the basis of chemical composition, pH titration, and thermogravimetric analysis. The effect on the exchange capacity of drying the exchanger at different temperatures has also been studied. The analytical importance of the material has been established by quantitative separation of Pb²⁺ from other metal ions.