Covalent biofunctionalization of silicon nitride surfaces

Covalently attached organic monolayers on etched silicon nitride (SixN4; x >/= 3) surfaces were prepared by reaction of SixN4-coated wafers with neat or solutions of 1-alkenes and 1-alkynes in refluxing mesitylene. The surface modification was monitored by measurement of the static water contact angle, XPS, IRRAS, AFM, and ToF-SIMS, and evidence for the formation of Si-C bonds is presented. The etching can be achieved by dilute HF solutions and yields both Si-H and N-H moieties. The resulting etched SixN4 surfaces are functionalized by terminal carboxylic acid groups in either of two ways: (a) via attachment of a 10-undecenoic acid 2,2,2-trifluoroethyl ester (trifluoro ethanol ester) and subsequent thermal acid hydrolysis; (b) through attachment of a photocleavable ester, and subsequent photochemical cleavage, as this would allow photopatterned functionalized SixN4. The carboxylic acids are successfully used for the attachment of oligopeptides (aspartame) and complete proteins using EDC/NHS chemistry. Finally, an amino-terminated organic monolayer can be formed by reaction of HF-treated SixN4 surfaces with a N-(omega-undecylenyl)phthalimide, which yields an amino-terminated surface upon deprotection with hydrazine.     

Functionalization of indium tin oxide

The preparation and functionalization of ITO surfaces has been studied using primarily X-ray photoemission spectroscopy and infrared reflection-absorption spectroscopy (IRRAS) and the reagents n-hexylamine and n-octyltrimethoxysilane (OTMS). Particular attention has been paid to characterization of the surfaces both before and after functionalization. Surfaces cleaned by ultraviolet (UV)/ozone treatment and subsequently exposed to room air have approximately 0.5-0.8 monolayers (ML) of adsorbed impurity C. Most is in the form of aliphatic species, but as much as one-half is partially oxidized and consists of C-OH, C-O-C, and/or >C=O groups. The coverage of these species can be reduced by cleaning in organic solvents prior to UV/ozone treatment. The OH coverage on the ITO surfaces studied here is relatively small (approximately 1.0 OH nm-2), based on the Si coverage after reaction with OTMS. A satellite feature in the O 1s XPS spectrum, often suggested to be a quantitative measure of adsorbed OH, receives a significant contribution from sources not directly related to hydroxylated ITO. n-Hexylamine adsorbs, at a saturation coverage of approximately 0.08 ML, via a Lewis acid-base interaction. The particular acid site has not been conclusively identified, but it is speculated that surface Sn sites may be involved. For OTMS, a saturation coverage of about 0.21 ML is found, and the C/Si atom ratios suggest that some displacement of preadsorbed organic impurities occurs during adsorption. The alkyl chain of adsorbed OTMS is disordered, with no preferred stereoisomer. However, the chain appears to lie mainly parallel to the surface with the plane defined by the terminal CH3-CH2-CH2- segment oriented essentially perpendicular to the surface.     

Chemical end-grafting of homogeneous polystyrene monolayers on mica and silica surfaces

Homogeneous polystyrene monolayers covalently end-attached on mica and silica surfaces were obtained using a "graft to" methodology. The grafting was achieved via nucleophilic substitution between silanol groups (Si-OH) containing surface and monochlorosilyl terminated polystyrene (PS). Different parameters, such as surface activation, grafting reaction time, polymer concentration, nature of solvent, and presence of catalyst, were investigated to determine the optimal conditions for creating very homogeneous and stable polymer monolayers. Ellipsometry, atomic force microscopy (AFM), surface forces apparatus (SFA), and contact angle measurements were used to characterize the polymer-grafted layers. An efficient plasma activation procedure was established to create a maximum number of silanol groups on mica surfaces without increasing the surface roughness. Surface reactivity was investigated by grafting trimethylchlorosilane (TMS) on OH-activated mica and silica. The maximum TMS surface coverage on activated mica is similar to that observed for silica. The stability of covalently attached TMS and PS layers in toluene and water were investigated. Both grafted layers (TMS and PS) partially detached from the mica and silica surfaces when immersed in water. Hydrolysis of the siloxane bond between the monochlorosilyl groups and the surface is the most probable cause of layer degrafting. The degrafting was much slower with the long PS polymer chains, compared to the small TMS molecules, which may act as a protective layer against hydrolysis.     

Small molecule chemisorption on indium-tin oxide surfaces: enhancing probe molecule electron-transfer rates and the performance of organic light-emitting diodes

Indium-tin oxide (ITO) surfaces have been modified by chemisorption of carboxylic acid functionalized small molecules: ferrocene dicarboxylic acid (1), 3-thiophene acetic acid (2), and 6-{4-[{4'-[[4-(5-carboxy-pentyloxy)-phenyl]-(4-methoxy-phenyl)-amino]-biphenyl-4-yl}-(4-methoxy-phenyl)-amino]-phenoxy}-hexanoic acid (p-OMe)2-TPD-(C5-COOH)2) (3). Voltammetrically determined surface coverages of 1-3 increased in two stages, the first stage completing in minutes, the latter stage taking several hours. Electron-transfer rate coefficients, kS, for the probe molecule ferrocene in acetonitrile likewise increased in two stages with increasing surface coverages of 1, 2, and 3. Fourier transform infrared spectroscopy of In2O3 powders, exposed for long periods to ethanol solutions of each modifier, confirmed the formation of indium oxalate-like surface species. X-ray photoelectron spectroscopy of carboxy-terminated alkanethiol-modified gold surfaces, exposed to these same In2O3(powder)/small molecule modifier solutions, showed the capture of trace levels of indium as a result of the chemisorption of these small molecules, suggesting that slow etching of the ITO surface also occurs during the chemisorption event. Conventional aluminum quinolate/bis-triarylamine organic light-emitting diodes (OLEDs) created on ITO surfaces modified with 1, 2, and 3, with and without an overlayer of PEDOT:PSS (a poly(thiophene)/poly(stryenesulfonate) ITO modifier), showed leakage currents lowered by several orders of magnitude and an increase in OLED device efficiency.     

纳米银粒子在氨基注入氧化铟锡玻璃基体表面的高密度吸附

研究了纳米银（AgNPs）在氨基注入氧化铟锡（ITO）薄膜表面的吸附.通过氨基注入的疗法得到了氨基功能化的ITO表面（NH₂/ITO）,并将纳米银直接吸附在NH₂/ITO上得到纳米银修饰NH₂/ITO基体（AgNPs/NH₂/ITO）.使用傅里叶红外光谱、X射线光电子能谱、原子力显微镜、扫描电镜、紫外可见光谱和电化学方法对AgNPs/NH₂/ITO制备过程进行了表征.结果显示纳米银可在NH₂/ITO表面高密度地吸附,并且纳米银有良好的电化学活性.这种不借助于有机连接分子吸附纳米银的方法为制备纳米银修饰材料提供了新的选择.     

Dense passivating poly(ethylene glycol) films on indium tin oxide substrates

We describe the formation and characterization of surface-passivating poly(ethylene glycol) (PEG) films on indium tin oxide (ITO) glass substrates. PEG chains with a molecular weight of 2000 and 5000 D were covalently attached to the substrates in a systematic approach using different coupling schemes. The coupling strategies included the direct grafting with PEG-silane, PEG-methacrylate, and PEG-bis(amine), as well as the two-step functionalization with aldehyde-bearing silane films and subsequent coupling with PEG-bis(amine). Elemental analysis by X-ray photoelectron spectroscopy (XPS) confirmed the successful surface modification, and XPS and ellipsometry provided values for film thicknesses. XPS and ellipsometry thickness values were almost identical for PEG-silane films but differed by up to 400% for the other PEG layers, suggesting a homogeneous layer for PEG-silane but an inhomogeneous distribution for other PEG coatings on the molecularly rough ITO substrates. Atomic force microscopy (AFM) and water contact angle goniometry confirmed the different degrees of surface homogeneity of the polymer films, with PEG-silane reducing the AFM rms surface roughness by 50% and the water contact angle hysteresis by 75% compared to uncoated ITO. The ability of the PEG layers to passivate the substrate against the nonspecific adsorption of biopolymers was tested using fluorescence-labeled immunoglobulin G and DNA oligonucleotides in combination with fluorescence microscopy. The results indicate a positive relationship between film density and homogeneity on one hand and the ability to passivate against biopolymer adhesion on the other hand. The most homogeneous layers prepared with PEG-silane reduced the nonspecific adsorption of fluorescence-labeled DNA by a factor of 300 compared to uncoated ITO. In addition, the study finds that the ratio of film thicknesses derived by ellipsometry and XPS is a useful parameter to quantify the structural integrity of PEG layers on molecularly rough ITO surfaces. The findings may be applied to characterize PEG or other polymeric films on similarly coarse substrates.     

Novel method for grafting alkyl chains onto glassy carbon. Application to the easy immobilization of ferrocene used as redox probe

Primary alkyl iodides (RI) have been found to react with a cathodically charged glassy carbon surface at potentials more negative than -1.7 V vs Ag/AgCl. In aprotic solvents, this reaction results in grafting of the alkyl chains onto carbon. It is proposed that the process corresponds to the cathodic charge of graphitized and fullerenized zones present in carbon followed by a displacement reaction (analogous to a nucleophilic attack) toward alkyl iodides. This new mode of grafting is applied to the immobilization of ferrocene used as an electrochemical probe. The present work points out the reaction of ω-iodoalkylferrocenes and quantifies the level of grafting of alkyl chains via this promising method for modification of carbon surfaces. Coverage levels were found to be high, reaching the apparent surface concentrations of 8 × 10(-9) mol cm(-2). These large values are explained on the basis of swelling of the interface provoked by progressive charging of the carbon surface via insertion of tetraalkylammonium cations concomitantly with the substitution process. Alkylferrocene layers deposited onto carbon were found to be chemically and electrochemically stable.     

Covalently attached monolayers on crystalline hydrogen-terminated silicon: extremely mild attachment by visible light

A very mild method was developed for the attachment of high-quality organic monolayers on crystalline silicon surfaces. By using visible light sources, from 447 to 658 nm, a variety of 1-alkenes and 1-alkynes were attached to hydrogen-terminated Si(100) and Si(111) surfaces at room temperature. The presence and the quality of the monolayers were evaluated by static water contact angles, X-ray photoelectron spectroscopy, and IR spectroscopy. Monolayers prepared by thermal, UV light, or visible light initiation were compared. Additionally, the ability of infrared reflection-absorption spectroscopy to study organic monolayers on silicon was explored. A reaction mechanism is discussed on the basis of investigations of the reaction behavior of 1-alkenes with silicon wafers with varying types and levels of doping. Finally, a series of mixed monolayers derived from the mixed solutions of a 1-alkene and an omega-fluoro-1-alkene were investigated to reveal that the composition of the mixed monolayers was directly proportional to the molar ratio of the two compounds in the solutions.     

1,1-二卤代-1-烯烃的制备及其在有机合成中的应用

1,1-二卤代-1-烯烃是有机化学中常见的合成片断,在合成化学中已得到了广泛的应用。该综述介绍了这一类化合物常见的制备方法以及反应的适用范围,并详细讨论了该类化合物在有机合成中的应用：(1)1,1-二卤代-1-烯烃在镁、有机锂、锌/溴化亚铜、二碘化钐、零价钯等金属或金属试剂作用下,发生α-消除反应生成烯基卡宾中间体的反应;(2)1,1-二卤代-1-烯烃在合成杂环以及核苷类似物等方面的应用。对于这类化合物在钯催化下的分子内(间)的偶联反应以及利用分子内的双环碳钯化反应,合成环状化合物等等方面的研究进展,也进行了详细的讨论。     

Seed-mediated growth of palladium nanocrystals on indium tin oxide surfaces and their applicability as modified electrodes

Palladium nanoparticles (PdNPs) were successfully attached and grown on an indium tin oxide (ITO) surface using a seed-mediated growth method, i.e., via a simple two-step immersion of the ITO substrate into the seed and growth solutions. After the growth treatment for 24 h, PdNPs grew up to 60-80 nm, exhibiting crystal-like appearances and accompanying the formation of short rodlike nanocrystals as a minor product. Thus prepared PdNPs tend to stick each other, so that the dense gathering of PdNPs was observed on the ITO surfaces. Due to the dense attachment, the PdNPs directly attached to the ITO (PdNP/ITO) electrode had a significantly lowered charge-transfer resistivity compared with that of a bare ITO, and the redox reaction of [Fe(CN)6]3-/[Fe(CN)6]4- was observed as reversible in 0.1 M phosphate buffer solution. The electrocatalytic property of PdNPs was confirmed for the reduction of oxygen. In addition, some typical responses were observed in 0.5 M H2SO4 with the PdNP/ITO electrode, reflecting both the characteristics of NPs and the thin layer in nanoscale. The present preparation method of PdNP-attached surfaces would be promising for catalytic applications as well as electrochemical uses.     

Wet chemical surface functionalization of oxide-free silicon

Silicon is by far the most important semiconductor material in the microelectronic industry mostly due to the high quality of the Si/SiO₂ interface. Consequently, applications requiring chemical functionalization of Si substrates have focused on molecular grafting of SiO₂ surfaces. Unfortunately, there are practical problems affecting homogeneity and stability of many organic layers grafted on SiO₂, such as silanes and phosphonates, related to polymerization and hydrolysis of Si–O–Si and Si–O–P bonds. These issues have stimulated efforts in grafting functional molecules on oxide-free Si surfaces, mostly with wet chemical processes. This review focuses therefore directly on wet chemical surface functionalization of oxide-free Si surfaces, starting from H-terminated Si surfaces. The main preparation methods of oxide-free H-terminated Si and their stability are first summarized. Functionalization is then classified into indirect substitution of H-termination by functional organic molecules, such as hydrosilylation, and direct substitution by other atoms (e.g. halogens) or small functional groups (e.g. OH, NH₂) that can be used for further reaction. An emphasis is placed on a recently discovered method to produce a nanopattern of functional groups on otherwise oxide-free, H-terminated and atomically flat Si(1 1 1) surfaces. Such model surfaces are particularly interesting because they make it possible to derive fundamental knowledge of surface chemical reactions.     

Surface modification of indium tin oxide via electrochemical reduction of aryldiazonium cations

The facile deposition of para-substituted aryl films onto indium-tin oxide (ITO) electrodes by the electrochemical reduction of aryl diazonium salts in acetonitrile is reported. For the deposition conditions used in this report, the aryl film thicknesses are on the order of 1-6 nm, suggesting a multilayer structure. Regardless of the functional group on the aryl diazonium cation, (NO(2), CO(2)H, or fluorene) the electrodeposition behavior onto ITO electrodes is similar to that seen on other electrode materials. XPS and UV-vis data support the introduction of organic functional surface groups to ITO. The blocking behavior of the aryl films on ITO toward the Ru(NH(3))(6)(3+/2+) redox couple is in agreement with electron transfer through conjugated organic layers. The facile preparation of patterned aryl films with regular-spaced 700 nm voids on ITO is also described. Atomic force microscopy and scanning surface potential microscopy on patterned NO(2) aryl films are used to assess the molecular structure and orientation. A 100 mV decrease in the contact potential over NO(2) aryl films relative to bare ITO suggests that the aryl films are loosely structured as deposited with the NO(2) groups oriented at a small angle away from the ITO surface.     

Sonochemical Reaction of Bifunctional Molecules on Silicon (111) Hydride Surface

While the sonochemical grafting of molecules on silicon hydride surface to form stable Si–C bond via hydrosilylation has been previously described, the susceptibility towards nucleophilic functional groups during the sonochemical reaction process remains unclear. In this work, a competitive study between a well-established thermal reaction and sonochemical reaction of nucleophilic molecules (cyclopropylamine and 3-Butyn-1-ol) was performed on p-type silicon hydride (111) surfaces. The nature of surface grafting from these reactions was examined through contact angle measurements, X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). Cyclopropylamine, being a sensitive radical clock, did not experience any ring-opening events. This suggested that either the Si–H may not have undergone homolysis as reported previously under sonochemical reaction or that the interaction to the surface hydride via a lone-pair electron coordination bond was reversible during the process. On the other hand, silicon back-bond breakage and subsequent surface roughening were observed for 3-Butyn-1-ol at high-temperature grafting (≈150 °C). Interestingly, the sonochemical reaction did not produce appreciable topographical changes to surfaces at the nano scale and the further XPS analysis may suggest Si–C formation. This indicated that while a sonochemical reaction may be indifferent towards nucleophilic groups, the surface was more reactive towards unsaturated carbons. To the best of the author’s knowledge, this is the first attempt at elucidating the underlying reactivity mechanisms of nucleophilic groups and unsaturated carbon bonds during sonochemical reaction of silicon hydride surfaces.     

Photochemical grafting of n-alkenes onto carbon surfaces: the role of photoelectron ejection

The grafting of molecular layers to carbon-based materials provides a way to combine the high chemical and thermal stability of these materials with surface properties such as chemical recognition or reactivity. The functionalization of surfaces with ultraviolet light has emerged as a way to modify difficult-to-functionalize materials, such as diamond. We have performed a combined experimental and computational investigation of the photochemical reaction of terminal alkenes with hydrogen-terminated carbon surfaces. 1-Alkenes carrying various terminal functional groups (-NHCOCF3, -NHCOO(tert-butyl), -COOCH3, -CH3) were grafted from the neat liquids using 254 nm light. These layers were characterized using X-ray Photoelectron Spectroscopy and Infrared Reflectance Absorption Spectroscopy. Pronounced differences in reactivity were observed between the molecules: trifluoroacetamide-terminated alkenes grafted the fastest and yielded self-terminating layers after approximately 4 h. Ultraviolet photoelectron spectroscopy and photocurrent measurements show that the grafting reaction involves photoemission of electrons into the liquid. Density functional calculations show that the reactivities of the four molecules are correlated with their electron affinities, with the trifluoroacetamide group acting as the best electron acceptor and having the highest reactivity. Our results demonstrate that photoejection of electrons from the solid into the acceptor levels of the alkenes initiates the functionalization reaction and controls the overall rate. Finally, marginally reactive n-alkenes were induced to react and form dense monolayers by seeding the carbon surface with small amounts of a good electron acceptor, such as the trifluoroacetamide moiety. This study provides important new mechanistic insights into the use of ultraviolet light to initiate grafting of alkenes onto surfaces.     

Super fast switching and low operating of liquid crystals sandwiched between ion beam-spurted ITO thin layers

Ion beam (IB)-spurted indium tin oxide (ITO) thin layers are used to align liquid crystals (LC) with a lower driving voltage. During IB spurting process, the microcrystals transforming to large crystals of ITO is intimated by the change of In (3d), Sn (3d) and O (1s) core level in XPS spectra and the surface topology modifications in SEM and AFM images, and IB-spurted ITO thin layers are comparably transparent and conductive compared with ITO thin layers. The increased interactions between LC and IB-spurted ITO thin layers together with the roughed surface topology of ITO thin layers are the main causes for LC alignment. The fast response and distribution of electrical dipoles to external voltage in LC causes LC’s extremely low threshold voltage drive; in addition, LC directly aligned on ITO thin layers free from alignment layers shield effect further decreases LC’s threshold voltage. 1.8-keV IB-spurted ITO thin layers are more appropriate to align LC with the threshold voltage of 0.4853 V and the rising time of 0.237 ms.     

In situ studies of the adsorption kinetics of 4-nitrobenzenediazonium salt on gold

Self-assembled organic layers are an important tool for modifying surfaces in a range of applications in materials science. Covalent modification of metal surfaces with aryldiazonium cations has attracted much attention primarily because this reaction offers a route for spontaneously grafting a variety of aromatic moieties from solution with high yield. We have investigated the kinetics of this process by performing real-time, in situ nanogravimetric measurements. The spontaneous grafting of 4-nitrobenzene diazonium salts onto gold electrodes was studied via quartz crystal microbalance (QCM) from aqueous solutions of the salt at varying concentrations. The concentration dependence of the grafting rate within the first 10 min is best modeled by assuming a reversible adsorption process with free energy comparable to that reported for arylthiols self-assembled on gold. Multilayer formation was observed after extended grafting times and was found to be favored by increasing bulk concentrations of the diazonium salt. Modified gold surfaces were characterized ex situ with cyclic voltammetry, infrared reflection absorbance spectroscopy, and X-ray photoemission spectroscopy. Based on the experimentally determined free energy of adsorption and on the observed grafting rates, we discuss a proposed mechanism for aryldiazonium chemisorption.     

Covalent attachment of organic monolayers to silicon carbide surfaces

This work presents the first alkyl monolayers covalently bound on HF-treated silicon carbide surfaces (SiC) through thermal reaction with 1-alkenes. Treatment of SiC with diluted aqueous HF solutions removes the native oxide layer (SiO2) and provides a reactive hydroxyl-covered surface. Very hydrophobic methyl-terminated surfaces (water contact angle theta = 107 degrees ) are obtained on flat SiC, whereas attachment of omega-functionalized 1-alkenes also yields well-defined functionalized surfaces. Infrared reflection absorption spectroscopy, ellipsometry, and X-ray photoelectron spectroscopy measurements are used to characterize the monolayers and show their covalent attachment. The resulting surfaces are shown to be extremely stable under harsh acidic conditions (e.g., no change in theta after 4 h in 2 M HCl at 90 degrees C), while their stability in alkaline conditions (pH = 11, 60 degrees C) also supersedes that of analogous monolayers such as those on Au, Si, and SiO2. These results are very promising for applications involving functionalized silicon carbide.     

Renewable and optically transparent electroactive indium tin oxide surfaces for chemoselective ligand immobilization and biospecific cell adhesion

In this report, we show the successful transfer of a sophisticated electroactive immobilization and release strategy to an indium tin oxide (ITO) surface to generate (1) optically transparent, robust, and renewable surfaces, (2) inert surfaces that resist nonspecific protein adsorption and cell attachment, and (3) tailored biospecific surfaces for live-cell high-resolution fluorescence microscopy of cell culture. By comparing the surface chemistry properties on both ITO and gold surfaces, we demonstrate the ITO surfaces are superior to gold as a renewable surface, in robustness (durability), and as an optically transparent material for live-cell fluorescence microscopy studies of cell behavior. These advantages will make ITO surfaces a desired platform for numerous biosensor and microarray applications and as model substrates for various cell biological studies.     

Nonleaching antibacterial glass surfaces via "Grafting Onto": the effect of the number of quaternary ammonium groups on biocidal activity

Antimicrobial surfaces were prepared using the "grafting onto" technique. Well-defined block copolymers containing poly(2-(dimethylamino)ethyl methacrylate) and poly(3-(trimethoxysilyl)propyl methacrylate) segments (PDMAEMA/PTMSPMA) and corresponding random copolymers were prepared via atom transfer radical polymerization (ATRP), followed by covalent attachment to a glass surface through reaction of the trimethoxysilyl groups with surface silanol groups. The density of quaternary ammonium (QA) groups available to bind small molecules in solution increased with polymer solution concentration and immobilization time. For the PDMAEMA 97- b-PTMSPMA xdiblock copolymers with a fixed length of PDMAEMA segment (degree of polymerization (DP) = 97) and varied lengths of PTMSPMA segments, maximal available surface charge was observed when the ratio of DP PDMAEMA to DP PTMSPMA was 5:1. The tertiary amino groups in immobilized PDMAEMA segments were reacted with ethyl bromide to form QA groups. Alternatively, block copolymers with prequaternized PDMAEMA segments were attached to surfaces. Biocidal activity of the surfaces with grafted polymers versus Escherichia coli ( E. coli) increased with the density of available QA units on the surface. The number of bacteria killed by the surface increased from 0.06 x 10(5) units/cm2 to 0.6 x 10(5) units/cm2, when the density of surface QA increased from 1.0 x 10(14) unit/cm2 to 6.0 x 10(14) unit/cm2. The killing efficiency of QA on all surfaces was similar with approximately 1 x 10(10) units of QA needed to kill one bacterium. The AFM analysis indicated that grafting onto the surface resulted in small patches of highly concentrated polymer. These patches appear to increase the killing efficiency as compared to surfaces prepared by grafting onto with the same average polymer density but with a uniform distribution.     

HAXPES of protected ITO surfaces at the buried P3HT/ITO interface

The characterization of buried interfaces is difficult and often has to be performed by a post‐processing method where the interface is exposed. Hard energy X‐ray photoelectron spectroscopy offers the ability to tune the X‐ray energy and thereby change the information depth. In this work, an inorganic/organic interface was evaluated, namely the poly(3‐hexylthiophene) (P3HT) interface with indium tin oxide (ITO), with relevance to organic photovoltaic devices. P3HT/ITO buried interfaces were examined using three X‐ray energies where the ITO surface was prepared under different pretreatment conditions. The P3HT film protected the ITO surface from adventitious adsorbents and allowed for sensitivity to the buried ITO surface. Robust peak fitting parameters were obtained to model the O 1 s and In 3d lineshapes. The deconvolution of these lineshapes allowed for the clear identification of a surface layer on the ITO which is oxidized to a greater extent than the underlying bulk ITO. The surface oxide layer, composed of indium oxide and indium hydroxide, is deficient of oxygen vacancies and would therefore be expected to act as an insulating barrier on the ITO surface. Peak fitting conditions allowed for an estimation of the relative thicknesses of this insulating layer. Copyright © 2012 John Wiley & Sons, Ltd.