The role of pH variation on the growth of zinc oxide nanostructures

In this paper we present a systematic study on the morphological variation of ZnO nanostructure by varying the pH of precursor solution via solution method. Zinc acetate dihydrate and sodium hydroxide were used as a precursor, which was refluxed at 90 °C for an hour. The pH of the precursor solution (zinc acetate di hydrate) was increased from 6 to 12 by the controlled addition of sodium hydroxide (NaOH). Morphology of ZnO nanorods markedly varies from sheet-like (at pH 6) to rod-like structure of zinc oxide (pH 10-12). Diffraction patterns match well with standard ZnO at all pH values. Crystallinity and nanostructures were confirmed by high-resolution transmission electron microscopy (HRTEM) and selected area electron diffraction (SAED) pattern, which indicates structure grew along [0 0 0 1] direction with an ideal lattice fringes distance 0.52 nm. FTIR spectroscopic measurement showed a standard peak of zinc oxide at 464 cm⁻¹. Amount of H⁺ and OH⁻ ions are found key to the structure control of studied material, as discussed in the growth mechanism.     

OH impurities in co-doped LiNbO3:Cr :ZnO congruent crystals

Infrared optical absorption has been used to study OH⁻impurities into congruent co-doped LiNbO₃:Cr³⁺:ZnO crystals doped with different Zn²⁺ concentration. The OH⁻ IR absorption spectra present three bands that can be associated with different OH⁻ complex centres available in the lattice. For crystals with lower Zn²⁺ concentrations (<4.7%) only one IR absorption band centred at 2867 nm (3490 cm⁻¹) is reported which is associated with the OH⁻ unperturbed vibration. For crystals with higher Zn²⁺ concentrations (>4.7%), two new bands associated with OH⁻vibration in distortion environment are reported. These bands are centred at 2827 nm (3537 cm⁻¹) and 2847 nm (3512 cm⁻¹) and can be associated with OH⁻-Zn²⁺ and Cr³⁺(Li⁺)-OH⁻-Zn²⁺(Int.) complex centres, respectively. Electron paramagnetic resonance (EPR) has been used to identify the Cr³⁺ centres in the lattice of the doped LiNbO₃:ZnO crystals.     

ZnO nanorods on undoped and indium-doped ZnO thin films as a TCO layer on nonconductive glass for dye-sensitized solar cells

We present the growth of ZnO nanostructures on indium-doped ZnO film on a non-conductive glass substrate. The indium-doped ZnO film was used as the transparent conductive layer replaces the ITO layer. Various indium doping concentrations can change the electrical properties of ZnO film. The reduced electrical resistivity was investigated from 16.60 × 10⁻² to 10 × 10⁻² Ω cm. after doping with the optimal concentration of 2 wt% indium. It is found that the characteristic of ZnO nanostructures was strongly affected with indium doping concentration in ZnO films. The overall structural characteristics of ZnO ranged from 100–500 nm in size and 7–10 μm in length and the branch-like structures can be revealed from the 2 wt% indium-doped ZnO film. The room-temperature photoluminescence spectra show a sharp ultraviolet band of 353 nm, indicated to the ZnO nanorods structure. The branch-like structures on the 2 wt% indium-doped film can be yielded the photovoltaic properties with a short-circuit current density of 3.96 mA/cm², an open-circuit voltage of 0.72 V, a fill factor of 20% and an overall power conversion efficiency of 0.56% under irradiance of 100 mW/cm² (AM 1.5 G).     

Comparative study of ethanol sensor based on gold nanoparticles: ZnO nanostructure and gold: ZnO nanostructure

Gold colloid:ZnO nanostructures were prepared from Zn powder by using thermal oxidation technique on alumina substrates, then it was impregnated by gold colloid for comparative study. The gold colloid is the solution prepared by chemical reduction technique; it appeared red color for gold nanoparticle solution and yellow color for gold solution. The heating temperature and sintering time of thermal oxidation were 700 °C and 24 h, respectively under oxygen atmosphere. The structural characteristics of gold colloid:ZnO nanostructures and pure ZnO nanostructures were studied using filed emission scanning electron microscope (FE-SEM). From FE-SEM images, the diameter and length of gold colloid:ZnO nanostructures and ZnO nanostructures were in the ranges of 100-500 nm and 2.0-7.0 μm, respectively. The ethanol sensing characteristics of gold colloid:ZnO nanostructures and ZnO nanostructures were observed from the resistance alteration under ethanol vapor atmosphere at concentrations of 50, 100, 200, 500, and 1000 ppm with the operating temperature of 260-360 °C. It was found that the sensitivity of sensor depends on the operating temperature and ethanol vapor concentrations. The sensitivity of gold colloid:ZnO nanostructures were improved with comparative pure ZnO nanostructures, while the optimum operating temperature was 300 °C. The mechanism analysis of sensor revealed that the oxygen species on the surface was O²⁻.     

Photoluminescent properties of Sm-doped zinc oxide nanostructures

Sm³⁺-doped zinc oxide nanophosphors were synthesized by solution combustion method. The size of the ZnO:Sm³⁺ nanostructures ranges from 40-60 nm. The photoluminescence spectra of ZnO:Sm³⁺ nanostructures is different from that of pure ZnO. The emission spectra of ZnO:Sm³⁺ nanostructures show a strong narrow emission peak at 425 nm and weak peaks at 457, 472 and 482 nm when excited with 255 nm.     

Effect of seed layer on the growth of well-aligned ZnO nanowires

We demonstrate that vertical well-aligned crystalline ZnO nanowire arrays were grown on ZnO/glass substrates by a low-temperature solution method. Different thicknesses of ZnO seed layers on glass substrates were prepared by radio-frequency sputtering. In this work it was found that the morphology of ZnO nanowires strongly depends on the thickness of ZnO seed layers. The average diameter of nanowires is increased from 50 to 130 nm and the nanowire density is decreased from 110 to 60 μm⁻² while the seed layer thickness is varied from 20 to 1000 nm. The improved control of the morphology of ZnO nanowire arrays may lead to an enhanced carrier collection of hybrid polymer photovoltaic devices based on ZnO.     

Dynamics of ZnO laser produced plasma in high pressure argon

Pulsed laser deposition of ZnO in high pressure gas offers a route for the catalyst-free preparation of ZnO nanorods less than 10 nm in diameter. This paper describes the results of some experiments to investigate the laser plume dynamics in the high gas pressure (5 × 10³-10⁴ Pa) regime used for PLD of ZnO nanorods. In this regime the ablation plume is strongly coupled to the gas and the plume expansion is brought to a halt within about 1 cm from the target. A 248 nm excimer laser was used to ablate a ceramic ZnO target in various pressures of argon. Time- and space-resolved UV/vis emission spectroscopy and Langmuir probe measurements were used to diagnose the plasma and follow the plume dynamics. By measuring the spatial profiles of Zn I and Zn II spectral lines it was possible to follow the propagation of the external and internal shock waves associated with the interaction of the ablation plume with the gas. The Langmuir probe measurements showed that the electron density was 10⁹-10¹⁰ cm⁻³ and the electron temperature was several eV. At these conditions the ionization equilibrium is described by the collisional-radiative model. The plume dynamics was also studied for ZnO targets doped with elements which are lighter (Mg), comparable to (Ga), and heavier (Er) than Zn, to see if there is any elemental segregation in the plume.     

Near-infrared luminescence of OH and Cl doped Bi4Ge3O12 crystals

OH⁻ and Cl⁻ doped Bi₄Ge₃O₁₂ (BGO) single crystals had been grown by Vertical Bridgman (VB) method. The structure of these crystals was determined by XRD, the transmittance and emission spectra in near infrared region (NIR) were measured at room temperature. 5% OH⁻ doped BGO shows a significant emission band peaking around 1181 nm under 808 nm laser diodes (LDs) excitation, and the 5% Cl⁻ doped BGO exhibits a relatively weak emission band as well. 100% and 5% OH⁻ doped BGO show noticeable emission band centered at about 1346 nm under 980 nm LDs excitation.     

OH-absorption properties of the optical damage region in codoped In/Mg:LiNbO3 crystals with various Li/Nb ratios

OH-absorption properties of the optical damage region in a series of codoped In/Mg:LiNbO₃ crystals with various Li/Nb ratios have been investigated. The OH⁻-associated vibrational peak at 3507 cm⁻¹ is confirmed to occur in crystals with Li/Nb ratio of 0.94. For codoped In/Mg:LiNbO₃ crystals with Li/Nb ratio of 1.05 and 1.20, the OH⁻-associated vibrational peaks are detected at 3536 and 3507 cm⁻¹ as well. A new peak at 3518 cm⁻¹ attributed to a (In_Nb)²⁻-OH⁻-(Mg_Nb)³⁻ defect center is revealed in crystals with Li/Nb ratio 1.38. When the “In-Mg threshold” concentration is reached, the optical damage resistance ability of codoped In/Mg:LiNbO₃ crystals is greatly improved.     

Low-temperature growth and ethanol-sensing characteristics of quasi-one-dimensional ZnO nanostructures

ZnO nanorods, nanobelts, nanowires, and tetrapod nanowires were synthesized via thermal evaporation of Zn powder at temperatures in the range 550-600 °C under flow of Ar or Ar/O₂ as carrier gas. Uniform ZnO nanowires with diameter 15-25 nm and tetrapod nanowires with diameter 30-50 nm were obtained by strictly controlling the evaporation process. Our experimental results revealed that the concentration of O₂ in the carrier gas was a key factor to control the morphology of ZnO nanostructures. The gas sensors fabricated from quasi-one-dimensional (Q1D) ZnO nanostructures exhibited a good performance. The sensor response to 500 ppm ethanol was up to about 5.3 at the operating temperature 300 °C. Both response and recovery times were less than 20 s. The gas-sensing mechanism of the ZnO nanostructures is also discussed and their potential application is indicated accordingly.     

Optical properties of ZnO nanoparticles synthesized by varying the sodium hydroxide to zinc acetate molar ratios using a Sol-Gel process

Material property dependence on the OH⁻/Zn²⁺ molar ratio of the precursor was investigated by varying the amount of NaOH during synthesis of ZnO. It was necessary to control the water content and temperature of the mixture to ensure the reproducibility. It was observed that the structural properties, particle size, photoluminescence intensity and wavelength of maximum intensity were influenced by the molar ratio of the precursor. The XRD spectra for ZnO nanoparticles show the entire peaks corresponding to the various planes of wurtzite ZnO, indicating a single phase. UV measurements show the absorption that comes from the ZnO nanoparticles in visible region. The absorption edge of these ZnO nanoparticles are shifted to higher energies and the determined band gap energies are blue shifted as the OH⁻/Zn² molar ration increases, due to the quantum confinement effects. The photoluminescence characterization of the ZnO nanostructures exhibited a broad emission band centred at green (600 nm) region for all molar ratios except for OH⁻/Zn²⁺ = 1.7 where a second blue emission around 468 nm was also observed. The photoluminescence properties of ZnO nanoparticles were largely determined by the size and surface properties of the nanoparticles.     

Effect of hydroxyl groups on Er-doped bismuth-borate glass and fiber

A series of Er³⁺-doped Bi₂O₃-B₂O₃-GeO₂-Na₂O glasses with different OH⁻ group contents were prepared and the interactions between Er³⁺ ions and OH⁻ groups were investigated. The observed increase of the fluorescence intensity and decaying variation from an evident non-exponential to a nearly exponential behavior of the Er³⁺:⁴I_13/2 level with the oxygen gas bubbling time was related to the reduction of the OH⁻ group contents evidenced by infrared (IR) absorption spectra, which demonstrated that the OH⁻ groups were dominant quenching centers of the excited Er³⁺. Meanwhile, by reducing the OH⁻ group contents in the fiber cores with the same glass composition, the simulated gain characteristics improved dramatically and a 12.4 dB gain at 1560 nm was achieved in a 20 cm fiber with 150 mW pumping power at 980 nm.     

Determination of electrical types in the P-doped ZnO thin films by the control of ambient gas flow

Phosphorus (P)-doped ZnO thin films with amphoteric doping behavior were grown on c-sapphire substrates by radio frequency magnetron sputtering with various argon/oxygen gas ratios. Control of the electrical types in the P-doped ZnO films was achieved by varying the gas ratio without post-annealing. The P-doped ZnO films grown at a argon/oxygen ratio of 3/1 showed p-type conductivity with a hole concentration and hole mobility of 1.5 × 10¹⁷ cm⁻³ and 2.5 cm²/V s, respectively. X-ray diffraction showed that the ZnO (0 0 0 2) peak shifted to lower angle due to the positioning of P³⁻ ions with a larger ionic radius in the O²⁻ sites. This indicates that a p-type mechanism was due to the substitutional P_O. The low-temperature photoluminescence of the p-type ZnO films showed p-type related neutral acceptor-bound exciton emission. The p-ZnO/n-Si heterojunction light emitting diode showed typical rectification behavior, which confirmed the p-type characteristics of the ZnO films in the as-deposited status, despite the deep-level related electroluminescence emission.     

Ag-N doped ZnO film and its p-n junction fabricated by ion beam assisted deposition

Ag-N doped ZnO film was synthesized by ion beam assisted deposition and its electrical properties and annealing property were investigated. The films remained p-type even after annealing at 400 °C in air for 10 min. While the annealing temperature went up to 500 °C, the conduction type of these films shifted from p-type to n-type. The p-type ZnO film revealed low resistivity (0.0016 Ω cm), low Hall mobility (0.65 cm² V⁻¹ s⁻¹) and high carrier concentration (5.8 × 10²⁰ cm⁻³). ZnO p-n homojunction consisting of a p-type layer (Ag-N doped ZnO film) and an n-type layer (In-doped ZnO film) had been fabricated by ion beam assisted deposition. With electrical measurement, its current-voltage curve had a typical rectifying characteristic with current rectification ratio of 25 at bias ±5 V and a reverse current of 0.01 mA at −5 V. The depletion width was estimated 3.8 nm by using p-n junction equation.     

Nonlinear optical properties of Au/ZnO nanoparticle arrays

The triangular-shaped Au/ZnO nanoparticle arrays were fabricated on fused quartz substrate using nanosphere lithography. The structural characterization of the Au/ZnO nanoparticle arrays was investigated by atomic force microscopy. The absorption peak due to the surface plasmon resonance of Au particles at the wavelength of about 570 nm was observed. The nonlinear optical properties of the nanoparticle arrays were measured using the z-scan method at a wavelength of 532 nm with pulse duration of 10 ns. The real and imaginary part of third-order nonlinear optical susceptibility, Re χ⁽³⁾ and Im χ⁽³⁾, were determined to be 1.15 × 10⁻⁶ and −5.36 × 10⁻⁷ esu, respectively. The results show that the Au/ZnO nanoparticle arrays have great potential for future optical devices.     

Morphology, photocatalytic and antibacterial activities of radial spherical ZnO nanorods controlled with a diblock copolymer

Radial spherical ZnO nanorods were synthesized directly from an aqueous zinc acetate dihydrate solution in the presence of the poly(ethylene oxide)-b-poly(propylene oxide) copolymer at a mole ratio of Zn²⁺:OH⁻ = 1:10. The diameter of the hexagonal facet and the length of each rod decreased with an increase of the copolymer concentrations. The blue-shift in the optical band gap was caused by an increase of the compressed lattice. The efficiency of photocatalytic degradation of methylene blue in aqueous solution increased with an increase of their surface areas. However, the decrease of their sizes did not improve their antibacterial activities.     

Fabrication of coaxial p-Cu2O/n-ZnO nanowire photodiodes

The authors report the deposition of Cu₂O onto vertically well aligned ZnO nanowires by DC sputtering. The average length, average diameter and density of these VLS-synthesized ZnO nanowires were 1 μm, 100 nm and 23 wires/μm², respectively. With proper sputtering parameters, the deposited Cu₂O could fill the gaps between the ZnO nanowires with good step coverage to form coaxial p-Cu₂O/n-ZnO nanowires with a rectifying current–voltage characteristic. Furthermore, the fabricated coaxial p-Cu₂O/n-ZnO nanowire photodiodes exhibit reasonably large photocurrent-to-dark-current contrast ratio and the fast responses.     

Effect of growth time on the structure, Raman shift and photoluminescence of Al and Sb codoped ZnO nanorod ordered array thin films

Al and Sb codoped ZnO nanorod ordered array thin films have been deposited on glass substrate with a ZnO seed layer by hydrothermal method at different growth time. The effect of growth time on structure, Raman shift, and photoluminescence (PL) was studied. The thin films at growth time of 5 h consist of nanorods growth vertically oriented with ZnO seed layer, and the nanorods with an average diameter of 27.8 nm and a length of 1.02 μm consist of single crystalline wurtzite ZnO crystal and grow along [0 0 1] direction. Raman scattering analysis demonstrates that the thin films at the growth time of 5 h have great Raman shift of 15 cm⁻¹ to lower wavenumber and have low asymmetrical factor Г_a/Г_b of 1.17. Room temperature photoluminescence reveals that there is more donor-related PL in films with growth time of 5 h.     

Spectroscopic properties of OH doped and Bi-rich Bi4Ge3O12 crystals by vertical Bridgman method

OH⁻ doped and Bi-rich Bi₄Ge₃O₁₂ (BGO) single crystals were grown by Vertical Bridgman (VB) method. The structure of these crystals was determined by XRD, and the emission spectra in visible and near infrared region (NIR) were measured at room temperature. The emission spectrum of Bi-rich BGO has extra peaks at 385, 367 and 357 nm, Bi-rich BGO after annealing in Ar at 500 °C for 5 h shows a significant emission band peaking around 1170 nm under 808 nm laser diodes (LDs) excitation, and OH⁻ doped BGO shows a noticeable emission band centered at about 1346 nm under 980 nm LDs excitation. A brief discussion is presented.     

Field emission from lotiform-like ZnO nanostructures synthesized via thermal evaporation method

Novel lotiform ZnO nanostructures were synthesized on silicon substrate via simple thermal evaporation. The average diameter of the ZnO nanostructures is ∼1.5 μm. The lotiform-like ZnO structures were formed by nanorods arrays with the average diameter of 70 nm. The as-grown lotiform ZnO nanostructures have excellent field-emission properties such as the low turn-on field of 3.4 V/μm, and very high emission current density of 12.4 mA/cm² at the field of 9.6 V/μm. These features make the lotiform-like ZnO nanostructures competitive candidates for field-emission-based displays. PACS 61.46.-w; 61.82.Rx; 78.67.-n; 73.63.Bd; 74.78.Na