Effects of SnO2 addition on the microstructure and magnetic properties of NiZn ferrites

The microstructure and magnetic properties of SnO₂-doped NiZn ferrites prepared by a solid-state reaction method have been investigated. Due to its low melting point (∼1127 °C), moderate SnO₂ enhanced mass transfer and sintering by forming liquid phase, which accelerated the grain growth. However, excessive SnO₂ producing much of liquid phase retarded mass transfer and sintering, leading to a decrease in grain size. The diffraction intensity of the samples doped with SnO₂ addition was stronger than that of the sample without addition. The lattice constant initially decreased up to a content of 0.10 wt% and showed an increase at higher content up to 0.50 wt%. The initial permeability (μ_i) initially increased up to a content of 0.15 wt% and showed a decrease at higher content up to 0.50 wt%; however, losses (P_L) measured at 50 kHz and 150 mT changed contrarily. Both saturation induction (B_S) and Curie temperature (T_C) decreased gradually with increasing SnO₂. Finally, the sample doped with 0.10–0.15 wt% SnO₂ showed the higher permeability and lower losses.     

Influence of V2O5 on the magnetic properties of nickel–zinc–copper ferrites

Additions of V₂O₅ were used to decrease the sintering temperature and to enhance the densification of NiZnCu ferrite. With a small amount of V₂O₅ (0.6–1.2 wt%) as a sintering aid, densification at low sintering temperature was observed. EDS analyses showed the presence of vanadium inside the ferrite grains. Microstructure investigation revealed heterogeneous grain size. Magnetic properties were deteriorated when increasing the V₂O₅ content. As a consequence, the permeability decreased and the core losses increased, which can be explained by the pinning of the domain walls to the grain defects.     

XPS and UPS study of Na deposition on thin film V2O5

The deposition of Na on thin film V₂O₅ has been study by using photoelectron spectroscopy. Vanadium ions are strongly reduced due to the deposition of Na. Three kinds of Na species were observed on the surface: the first is assigned to intercalated Na; the second is contributed to Na₂O₂; the third is appointed to metallic Na. The formation of Na₂O₂ leads to arise an emission line at about 10.3 eV in the valence band spectra. The metallic Na will further react with the oxides substrate and form Na₂O₂ on the surface in UHV chamber.     

Optical characteristics of amorphous V2O5 thin films colored by an excimer laser

The V₂O₅ films were prepared by an RF sputtering method, and the amorphous films were colored by an UV excimer laser. The crystallinity of the as-grown V₂O₅ film was degenerated greatly by laser irradiation, as determined by X-ray diffraction (XRD) and Raman studies. The transmission and complex refractive index spectra of the V₂O₅ film were affected by variations in the microstructure, including the surface morphology, crystalline structure, and substoichiometry with an oxygen deficiency. Considerable emissions due to oxygen vacancies and band transition of photoluminescence (PL) peaks were observed, and the peaks were significantly changed after laser irradiation. The variations in the optical properties in both films may be attributed to oxygen deficiency induced by laser irradiation.     

Effects of different sintering temperature and Nb2O5 content on structural and magnetic properties of Z-type hexaferrites

Nb-doped Z-type hexaferrites (Ba₃(Co_0.4Zn_0.6)₂Fe₂₄O₄₁) with composition of Ba₃(Co_0.4Zn_0.6)₂Fe₂₄O₄₁+x Nb₂O₅ (where x=0.0, 0.1, 0.2, 0.4, 0.6, 0.8, 1.2, 1.6 and 2.0 wt%) were prepared by a solid-state reaction method. The effects of different sintering temperature (T_s) and Nb₂O₅ content on the sintering behaviors, phase composing, microstructure, and magnetic properties of the samples were investigated. The results from X-ray diffraction and scanning electron microscopy show that as the amount of Nb₂O₅ additive increases, the major phase changes to Z-phase, Simultaneously, M-phase and a small amount of niobate phase appear. The Nb₂O₅ additive promotes the grain growth as reaction center at lower sintering temperature (1220 °C), but at higher temperature (1260 °C), niobate phase separated out in grain boundaries as secondary phase will restrain abnormal grain growth, so closed pores in grains are not formed. The Nb₂O₅ additive can enhance densification, improve initial permeability of hexaferrites by increasing the grain growth of hexaferrite and the displacement of ions in the sintering process due to the aberration and activation of crystal lattice, which is accompanied by the solubility of Nb⁵⁺ in the hexaferrites. A relative density of 96%, maximum initial permeability (32–33), minimum coercivity (454–455 A/m) and resonance frequency above 400 MHz were obtained for the sample with 0.8 wt% Nb₂O₅ sintered at 1260 °C for 6 h.     

Electrical properties vs. microstructure of nanocrystallized V2O5-P2O5 glasses — An extended temperature range study

An electronically conducting nanomaterial was synthesized by nanocrystallization of a 90V₂O₅·10P₂O₅ glass and its electrical properties were studied in an extended temperature range from − 170 to + 400 °C. The conductivity of the prepared nanomaterial reaches 2 ? 10^− 1 S cm^− 1 at 400 °C and 2 ? 10^− 3 S cm^− 1 at room temperature. It is higher than that of the original glass by a factor of 25 at room temperature and more than 100 below − 80 °C. A key role in the conductivity enhancement was ascribed to the material's microstructure, and in particular to the presence of the large number of small (ca. 20 nm) grains of crystalline V₂O₅. The observed conductivity dependencies are discussed in terms of the Mott's theory of the electronic hopping transport in disordered systems. Since V₂O₅ is known for its ability to intercalate lithium, the presented results might be helpful in the development of cathode materials for Li-ion batteries.     

Effects of Ta2O5 addition on the microstructure and temperature dependence of magnetic properties of MnZn ferrites

MnZn ferrites with the chemical formula Mn_0.68Zn_0.25Fe_2.07O₄ have been prepared by the conventional ceramic technique. Toroidal cores were sintered at 1350 °C for 4 h in N₂/O₂ atmosphere with 4% oxygen. Then the influence of Ta₂O₅ addition on the microstructure and temperature dependence of magnetic properties of MnZn ferrites was investigated by characterizing the fracture surface micrograph and measuring the magnetic properties over a temperature ranging from 25 to 120 °C. The results show that, when the Ta₂O₅ concentration is not more than 0.04wt%, the grain size has a slight increase with the increase of Ta₂O₅ concentration, the temperature of secondary maximum peak in the curve of initial permeability versus temperature and the lowest power loss shift to lower temperature. However, excessive Ta₂O₅ concentration (>0.04wt%) results in the exaggerated grain growth and porosity increase, which make the initial permeability and saturation magnetic flux density decrease and the power loss increase at room temperature. Furthermore, the temperature of secondary maximum peak in the curve of initial permeability versus temperature and the lowest power loss shift to about 100 °C.     

Substrate effects on V2O3 thin films

We apply density functional theory and the augmented spherical wave method to analyze the electronic structure of V₂O₃ in the vicinity of an interface to Al₂O₃. The interface is modeled by a heterostructure setup of alternating vanadate and aluminate slabs. We focus on the possible modifications of the V₂O₃ electronic states in this geometry, induced by the presence of the aluminate layers. In particular, we find that the tendency of the V 3d states to localize is enhanced and may even cause a metal-insulator transition.     

Effects of sintering temperature and Bi2O3 content on microstructure and magnetic properties of LiZn ferrites

The effects of sintering temperature and Bi₂O₃ content on the microstructure and magnetic properties of lithium–zinc (LiZn) ferrites prepared by a conventional ceramic method were investigated. The results show that the densification behavior and grain growth rate were greatly improved by the addition of Bi₂O₃, because a liquid phase sintering occurred during the sintering process at high temperature due to the low-melting point of Bi₂O₃ (825 °C). X-ray diffraction (XRD) patterns of the slightly doped samples did not reveal the appearance of any phase other than spinel LiZn ferrite. However, the secondary phase of perovskite BiFeO₃ was detected for Bi₂O₃ content of more than 0.25 wt%. The studies further show that Bi oxide was present at grain boundary, and promoted the grain growth as reaction center at lower temperature. A high saturation magnetization, squareness ratio, minimum ferromagnetic resonance linewidth and low coercive force were obtained for the sample with 1.00 wt% Bi₂O additive at lower sintering temperature (1100 °C).     

Microwave sintering of high-permeability (Ni0.20Zn0.60Cu0.20)Fe1.98O4 ferrite at low sintering temperatures

The (Ni_0.20Zn_0.60Cu_0.20)Fe_1.98O₄ ferrite was sintered using microwave sintering and conventional sintering technique, respectively. It was found that microwave sintering technique can effectively promote the forward diffusion of ions and thus accelerate the sintering process, resulting in the grain growth and the densification of matrix. At the low frequency of 100 kHz, the magnetizing contribution of domain wall motion is predominant, and compact and coarse matrixes are favorable for domain wall motion, giving rise to improvement of relative initial permeability and loss of ferrites. Using microwave sintering technique, for the (Ni_0.20Zn_0.60Cu_0.20)Fe_1.98O₄ ferrite, the relative initial permeability μ_i of about 2000 and the relative loss factor tanδ/μ_i of about 8.7×10⁻⁶ at 100 kHz were achieved at only 980 °C sintering temperature. In addition, the sintering time of ferrites was reduced from 5 to 0.5 h by using microwave sintering technique.     

Influences of Bi2O3 on microstructure and magnetic properties of MnZn ferrite

MnZn ferrites were prepared by conventional oxide ceramic process. The effects of Bi₂O₃ on microstructure and magnetic properties of MnZn ferrites were investigated by means of characterizing the fracture surface micrograph, composition of grain boundary, magnetic properties and density by scanning electron microscope (SEM), energy dispersive X-ray spectroscope (EDS), B-H analyzer and Archimedes method, respectively. The results indicate that Bi₂O₃ mainly segregates and concentrates in the grain boundary regions, promotes solid-state reaction and grain growth, reduces porosity and enhances density. Optimum addition of Bi₂O₃ increases the permeability and saturation magnetic induction, meanwhile ensures the well frequency stability of permeability.     

Electrochemical behaviour of sputtered c-V2O5 and LiCoO2 thin films for solid state lithium microbatteries

Here are reported for the first time electrochemical data on all-solid-state lithium microbatteries using crystalline sputtered V₂O₅ thin films as cathode materials and LiPON as solid electrolyte. The stable specific capacity of 30 µAh/cm² found with a 2.4 µm thick film competes very well with the best values obtained for solid state microbatteries using amorphous films. With the challenge of decreasing the temperature of heat treatment for sputtered LiCoO₂ thin films, we show that a temperature of 500 °C combined with an optimized bias sputtering (-50 V) allows to get highly crystalline deposits, to minimize the presence of Co₃O₄ and to suppress any trace of the cubic phase. At the same time the theoretical specific capacity is reached in the 4.2 V-3 V range and a good cycling behaviour is achieved with a high capacity of 50 µAh/cm²/µm after 140 cycles at 10 µA.cm².     

Synthesis of solid solutions of Mn and Bi substituted V2O5 and substitutional effect in structural and optoelectronic behavior

V₂O₅ is an attractive material with enormous technological applications such as cathode material in lithium batteries and electrochromic displays. Mn and Bi substitution in vanadium pentoxide (V₂O₅) was done by conventional solid state reaction technique with different composition. The chemical composition, structural and optical properties were investigated employing different techniques, such as XRD, SEM and UV-Vis Spectra. XRD studies exhibit the predominant (0 0 1) peak of orthorhombic phase. SEM image shows the uniformity of the material synthesized. Variable transmittance is exhibited by samples doped with different percentages of dopants. The dielectric property studies and ac conductivity measurements were carried out by Hioki LCR Hi-Tester.     

Effect of BiFeO3 addition on Bi2O3–ZnO–Nb2O5 based ceramics

In this paper, low temperature sintering of the Bi₂(Zn_1/3Nb_2/3)₂O₇ (β-BZN) dielectric ceramics was studied with the use of BiFeO₃ as a sintering aid. The effects of BiFeO₃ contents and the sintering temperature on the phase structure, density and dielectric properties were investigated. The results showed that the sintering temperature could be decreased and the dielectric properties could be retained by the addition of BiFeO₃. The structure of BiFeO₃ doped β-BZN was still the monoclinic pyrochlore phase. The sintering temperature of BiFeO₃ doped β-BZN ceramics was reduced from 1000 °C to 920 °C. In the case of 0.15 wt.% BiFeO₃ addition, the β-BZN ceramics sintered at 920 °C exhibited good dielectric properties, which were listed as follows: ε_r = 79 and tan δ = 0.00086 at a frequency of 1 MHz. The obtained properties make this composition to be a good candidate for the LTCC application.     

Emission features of Ho ion in Nb2O5, Ta2O5 and La2O3 mixed Li2O-ZrO2-SiO2 glasses

Li₂O-ZrO₂-SiO₂: Ho³⁺ glasses mixed with three interesting d-block elemental oxides, viz., Nb₂O₅, Ta₂O₅ and La₂O₃, were prepared. Optical absorption and photoluminescence spectra of these glasses have been recorded at room temperature. The luminescence spectra of Nb₂O₅ and Ta₂O₅ mixed Li₂O-ZrO₂-SiO₂ glasses (free of Ho³⁺ ions) have also exhibited broad emission band in the blue region. This band is attributed to radiative recombination of self-trapped excitons (STEs) localized on substitutionally positioned octahedral Ta⁵⁺ and Nb⁵⁺ ions in the glass network. The Judd-Ofelt theory was successfully applied to characterize Ho³⁺ spectra of all the three glasses. From this theory various radiative properties, like transition probability A, branching ratio β_r and the radiative lifetime τ_r, for ⁵S₂ emission levels in the spectra of these glasses have been evaluated. The radiative lifetime for ⁵S₂ level of Ho³⁺ ions has also been measured and quantum efficiencies were estimated. Among the three glasses studied the La₂O₃ mixed glass exhibited the highest quantum efficiency. The reasons for such higher value have been discussed based on the relationship between the structural modifications taking place around the Ho³⁺ ions.     

Effects of applied magnetic field and pressures on the magnetic properties of nanocrystalline CoFe2O4 ferrite

Nanocrystalline CoFe₂O₄ ferrite with crystallite sizes of 30 nm have been successfully prepared by an emulsion method. X-ray diffractometer (XRD) shows that nanocrystalline CoFe₂O₄ ferrite possesses face center cubic structure. Crystal structure of the CoFe₂O₄ nanocrystals will not be changed by the applied magnetic field and pressures. The obtained CoFe₂O₄ nanocrystalline powders were pressed into thin columns with different pressures. Meanwhile, the dependences of the applied pressures and the direction of applied magnetic field on the magnetic properties of the CoFe₂O₄ nanocrystals were investigated in detail using vibrating sample magnetometer (VSM). The pressed CoFe₂O₄ nanocrystal gains the most excellent magnetisms in a parallel applied magnetic field.     

Effects of RE2O3 (RE = Tm, Sc, Yb) addition on the superconducting properties of ErBa2Cu3Oy

We investigated the effects of added Tm₂O₃, Sc₂O₃, and Yb₂O₃ on the superconducting properties of sintered Er123 samples. Tm₂O₃ addition caused the least T_c degradation, exhibiting a T_c above 90 K even for 17 vol% addition. Samples with added Sc₂O₃ maintained a T_c at above 90 K up to an addition of 7.2 vol%, while Yb₂O₃-containing samples showed a monotonic decrease in T_c with increased vol% of added Yb₂O₃. Tm₂O₃-containing samples exhibited a slight increase in J_c(0.1 T)/J_c(0) and had constant J_c values even for 17 vol% addition. XRD and SEM results indicate that the Tm₂O₃ is very stable in the superconducting matrix.     

Preparation and magnetic properties of BaFe12O19/Ni0.8Zn0.2Fe2O4 nanocomposite ferrite

Nanocomposite of hard (BaFe₁₂O₁₉)/soft ferrite (Ni_0.8Zn_0.2Fe₂O₄) have been prepared by the sol–gel process. The nanocomposite ferrite are formed when the calcining temperature is above 800 °C. It is found that the magnetic properties strongly depend on the presintering treatment and calcining temperature. The “bee waist” type hysteresis loops for samples disappear when the presintering temperature is 400 °C and the calcination temperature reaches 1100 °C owing to the exchange-coupling interaction. The remanence of BaFe₁₂O₁₉/Ni_0.8Zn_0.2Fe₂O₄ nanocomposite ferrite with the mass ratio of 5:1 is higher than a single phase ferrite. The specific saturation magnetization, remanence magnetization and coercivity are 63 emu/g, 36 emu/g and 2750 G, respectively. The exchange-coupling interaction in the BaFe₁₂O₁₉/Ni_0.8Zn_0.2Fe₂O₄ nanocomposite ferrite is discussed.     

Effects of deposition parameters on laser-induced damage threshold of Ta2O5 films

Ta₂O₅ films were deposited on BK7 substrates by e-beam evaporation with different deposition parameters such as substrate temperature (323-623 K), oxygen pressure (0.5-3.0×10⁻² Pa) and deposition rate (0.2-0.5 nm/s). Absorption, scattering and chemical composition were investigated by surface thermal lensing (STL) technique, total integrated scattering (TIS) measurement and X-ray photoelectron spectroscopy (XPS), respectively. The laser-induced damage threshold (LIDT) was assessed using pulsed Nd:YAG 1064 nm laser at a pulse length of 12 ns. The results showed that optical properties, absorption and LIDT were influenced by the deposition parameters and annealing. However, scattering was little correlated with the deposition parameters. On the whole, the LIDT increased with increasing substrate temperature and oxygen pressure, whereas it increased firstly and then decreased upon increasing deposition rate. After annealing at 673 K for 12 h, the LIDT of films improved significantly. The dependence of possible damage mechanism on deposition parameters was discussed.     

Direct micron-sized LiMn2O4 particle coating on LiCoO2 cathode material using surfactant

Micron-sized LiMn₂O₄ particles were easily coated on LiCoO₂ cathodes using an amphoteric gelatin surfactant at pH4–5. The coated LiCoO₂ material showed a significantly higher thermal stability during charging and capacity retention on cycling at 4.6 V, compared to the bare LiCoO₂.