Effect of Nd concentration on structural and optical properties of Nd:Y2O3 transparent ceramic

Y₂O₃ transparent ceramics with different Nd concentration (0.1-7.0at%) were fabricated using ZrO₂ as additive. All the samples exhibit high transparency over a broad spectral region. The elements (Y, O and Nd) are uniformly distributed in the ceramic body, and the average grain size increases with Nd content. Based on the absorption spectrum, the Judd-Ofelt intensity parameters are calculated (Ω₂=4.364×10⁻²⁰ cm², Ω₄=3.609×10⁻²⁰ cm² and Ω₆=2.919×10⁻²⁰ cm²). The absorption coefficients increase linearly with Nd³⁺ doping concentration. The absorption cross-section at 804 nm and stimulated emission cross-section at 1078 nm are calculated to be 1.54×10⁻²⁰ and 7.24×10⁻²⁰ cm², respectively. All the emission bands exhibit the highest emission intensities with 1.0at% Nd³⁺ ion content, while the lifetime decreases dramatically from 321.5 μs (0.1at% Nd) to 17.9 μs (7.0at% Nd). According to the emission spectra and measured lifetime, the optimum doping concentration of Nd³⁺ ion in Y₂O₃ transparent ceramic might be around 1.0at%.     

Enhanced optical activation of Er in Er-doped Al2O3 powders by Y codoping in a sol-gel method

Enhanced photoluminescence (PL) mechanism of Er³⁺-doped Al₂O₃ powders by Y³⁺ codoping at wavelength 1.53 μm has been investigated through PL measurements of 0.1 mol% Er³⁺- and 0-20 mol% Y³⁺-codoped Al₂O₃ powders prepared at a sintering temperature of 900 °C in a non-aqueous sol-gel method. PL intensity and lifetime of Er³⁺-Y³⁺-codoped Al₂O₃ powders composed of γ-(Al,Er,Y)₂O₃ and θ-(Al,Er,Y)₂O₃ phases increased with increasing Y³⁺-codoping concentration. The 10-20 mol% Y³⁺ codoping in 0.1 mol% Er³⁺-doped Al₂O₃ powders intensified the PL intensity by about 20 times, with a PL lifetime prolonged from 3.5 to 5.8 ms. A maximal increase of the optical activity of Er³⁺ in 0.1 mol% Er³⁺-Y³⁺-codoped Al₂O₃ powders about one order was achieved by 10-20 mol% Y³⁺ codoping. It is found that the improved PL properties for Er³⁺-Y³⁺-codoped Al₂O₃ powders are mainly attributed to enhanced optical activation of Er³⁺ in the Al₂O₃ by Y³⁺ codoping, and to the slightly increased radiative quantum efficiency of Er³⁺ in the Al₂O₃.     

Spectral properties of Ce3+ doped yttrium lanthanum oxide transparent ceramics

Ce3+-doped yttrium lanthanum oxide (Y0.9La0.1)2O3 transparent ceramics is fabricated with nanopowders and sintered in H2 atmosphere. The spectral properties of Ce:(Y0.9La0.1)2O3 transparent ceramics are investigated. There appear two characteristic absorption peaks of Ce3+ ions at 230 nm and 400 nm, separately. It is found that Ce3+ ions can efficiently produce emission at 384 nm from (Y0.9La0.1)2O3 transparent ceramic host, while the emission is completely quenched in Re2O3 (Re=Y, Lu, La) host materials.     

Effect of iso- and heterovalent additives on characteristics of highly transparent Nd(Yb):Y<Subscript>2</Subscript>O<Subscript>3</Subscript> ceramics

The possibility of synthesis and characteristics of highly transparent Y₂O₃ ceramics doped with Nd³⁺ and Yb³⁺ were studied. The ceramics crystal structure was disordered for the first time by simultaneously substituting Y³⁺ cations by Lu³⁺ or Sc³⁺ isovalent ions and Zr⁴⁺ heterovalent ions. The developed technique allowed synthesis of highly transparent Nd³⁺:Y₂O₃, Nd³⁺: Y₂O₃ + 6 mol % ZrO₂, Nd³⁺: (Lu_0.25Y_0.75)₂O₃ + 6 mol % ZrO₂, Nd³⁺:(Sc_0.25Y_0.75)₂O₃ + 6 mol % ZrO₂, and Yb³⁺:(Sc_0.25Y_0.75)₂O₃ + 6 mol % ZrO₂ ceramics with transmittance to 82.2%. It was shown that introduction of iso- and heterovalent additives Sc₂O₃, Lu₂O₃, and ZrO₂ into Nd³⁺:Y₂O₃ decreases average crystallite sizes to ∼1 μm and reduces the pore content, thus making it possible to produce pore-free ceramics. These additives broaden the spectral band of the ⁴ F _3/2 → ⁴ I _11/2 transition of the neodymium ion to 40 nm.     

X-ray photoelectron spectroscopic investigations on cubic BaTiO3, BaTi0.9Fe0.1O3 and Ba0.9Nd0.1TiO3 systems

X-ray photoelectron spectroscopic (XPS) studies were carried out on wet-chemically synthesized cubic BaTiO₃, Ba_0.9Nd_0.1TiO₃ and BaTi_0.9Fe_0.1O_3−δ powders. The compounds were prepared by hydrothermal and gel to crystallite conversion technique; and phases formed readily at 420 K. The phase purity of the powders was confirmed from X-ray diffractometry. Chemical state and chemical environment of the constituent elements in the compositions were examined by XPS. Ba²⁺ was found to exist in two different chemical environments in these titanates. The Ti 2p_3/2 photoelectron peak in BaTi_0.9Fe_0.1O_3−δ was found to be broadened after Fe³⁺ substitution. Any resolvable broadening was not observed distinctly in the Ti 2p peak for Ba_0.9Nd_0.1TiO₃, unsintered BaTiO₃ and BaTiO₃ annealed in hydrogen (8% H₂ + Ar) at 1000 K. The prevalence of mixed-valent titanium and iron in BaTi_0.9Fe_0.1O_3−δ composition was evident from the XPS results and was further supported by the enhanced electrical conductivity at 298-550 K for BaTi_0.9Fe_0.1O_3−δ in comparison to BaTiO₃ and Ba_0.9Nd_0.1TiO₃. Hydroxyl incorporation was facilitated by substituting Nd³⁺ in Ba-sublattice. The presence of hydroxyls was observed from the broadening of the O 1s peak in XPS studies of the compounds.     

Raman spectroscopic investigation of lanthana‐doped neodymium‐yttria transparent ceramics

Transparent ceramics of the formula (Nd_0.01La_xY_0.99−x)₂O₃ (x = 0, 0.05, 0.10) were made with nanopowders and sintered in H₂ atmosphere. The Raman spectra of Ln₂O₃ (Ln = Y, La, Nd) powders and (Nd_0.01La_xY_0.99−x)₂O₃ ceramics were investigated. The results show that both La₂O₃ and Nd₂O₃ powders are of hexagonal structure, and all (Nd_0.01La_xY_0.99−x)₂O₃ ceramics exhibit the same cubic Y₂O₃ crystal structure. Their lattice parameters were refined by the Rietveld method. The full‐widths at half‐maximum of Raman peaks increase with the increase in La₂O₃ content in transparent (Nd_0.01Y_0.99)₂O₃ ceramics, while their intensities decrease. At the same time, All Raman peaks shift to lower wavenumbers, and the phonon energy is slightly reduced. Copyright © 2010 John Wiley & Sons, Ltd.     

Low-voltage cathodoluminescence property of Li-doped Gd2−xYxO3:Eu

Cathodoluminescent (CL) spectra of Li-doped Gd_2−xY_xO₃:Eu³⁺ solid-solution (0.0?x?0.8) were investigated at low voltages (300 V-1 kV). The CL intensity is maximum for the composition of x=0.2 and gradually reduces with increasing the amount of substituted Y content. In particular, small (∼100 nm) particles of Li-doped Gd_1.8Y_0.2O₃:Eu³⁺ are obtained by firing the citrate precursors at only 650°C for 18 h. Relative red-emission intensity at 300 V of this phosphor is close to 180% in comparison with that of commercial red phosphor Y₂O₃:Eu³⁺. An increase of firing temperature to 900°C results in 400-600 nm sized spherical particles. At low voltages (300-800 V), the CL emission of 100 nm sized particles is much stronger than that of 400-600 nm sized ones. In contrast, the larger particles exhibit the higher CL emission intensity at high voltages (1-10 kV). Taking into consideration small spherical morphology and effective CL emission, Li-doped Gd_1.8Y_0.2O₃:Eu³⁺ appears to be an efficient phosphor material for low voltage field emission display.     

The effect of flux materials on the physical and optical properties of Eu-activated yttrium oxide phosphors

A flux fusion method was used to obtain the various sizes of Eu³⁺-activated Y₂O₃ red phosphors. The flux material was selected as an independent variable to control the physical properties of phosphor particles and their effects on the morphology and size distribution of phosphors were examined by scanning electron microscopy. The concentration of the flux materials and synthetic temperature were optimized for maximal photoluminescence intensity. Fluoride-based flux materials were found to work for the crystal formation of Eu³⁺-activated Y₂O₃. In particular, when a BaF₂ flux was used during the reaction at 1450 °C for 3 h, the photoluminescence (PL) intensity of Eu³⁺-activated Y₂O₃ was 25% higher than that without a flux and spherical phosphors had a mean particle size of 4-5 μm. The morphology and size distribution of the synthesized Eu³⁺-activated Y₂O₃ phosphor were predominantly dependent upon the type and concentration of flux material and synthetic temperature.     

Investigation of up-conversion luminescence properties of RE/Yb co-doped Y2O3 transparent ceramic (RE=Er, Ho, Pr, and Tm)

RE/Yb co-doped Y₂O₃ transparent ceramics (RE=Er, Ho, Pr, Tm) were fabricated and characterized from the point of up-conversion luminescence. All the samples exhibit high transparence not only in near-infrared band (NIR) band but also in visible region, which ensures the output of the up-conversion luminescence. Under 980 nm excitation, green and red emissions were observed in Er, Yb:Y₂O₃ transparent ceramic, while green emission was detected in Ho, Yb and Pr, Yb co-doped Y₂O₃ transparent ceramics. In Tm, Yb co-doped Y₂O₃ ceramic, very intense blue up-conversion luminescence was detected. The dependence of up-conversion emission intensity on the pumping power was measured for each RE/Yb co-doped Y₂O₃ transparent ceramic, and the up-conversion mechanism was discussed in detail. Meanwhile, the energy transfer efficiency was calculated.     

Intense ultraviolet and blue upconversion emissions in Yb-Tm codoped stoichiometric Y7O6F9 powder

Stoichiometric Y₇O₆F₉ powder codoped with Yb³⁺-Tm³⁺ was synthesized via co-precipitation and subsequent calcining route. The results of X-ray diffraction and transmission electron microscopy reveal that when the calcining temperature is beyond 800 °C, orthorhombic YF₃ nanoparticles can be completely oxidized into orthorhombic Y₇O₆F₉ powder. Under the excitation of a 980 nm laser, Y₇O₆F₉ powder exhibits multicolor UC emission in regions spanning the UV to the NIR. In addition, the upconversion emission intensities of YF₃, Y₇O₆F₉ and Y₂O₃ powders were compared under the same dopant condition (Yb/Tm=5/0.5 mol%). The low phonon energy revealed by Raman spectra helped to understand the high efficient upconversion emission of Y₇O₆F₉ and the main phonon vibration of Y₇O₆F₉ lies at 472 cm⁻¹, which is far lower that of Y₂O₃ (at 708 cm⁻¹). Our results indicate that orthorhombic rare earth ions doped Y₇O₆F₉ is an efficient matrix for UV and blue UC emission, and has potential applications in color displays, anti-counterfeiting and multicolor fluorescent labels.     

Preparation and photoluminescence characteristics of Eu-doped MgAl1.8Y0.2O4 nanocrystals

A simple combustion route was employed for the preparation of Eu³⁺-doped MgAl_1.8Y_0.2−xO₄ nanocrystals using metal nitrates as precursors and urea as a fuel in a preheated furnace at 500 °C. The powders thus obtained were then fired at 1000 °C for 3 h to get better luminescent properties. The incorporation of Eu³⁺ activator in these nanocrystals was checked by luminescence characteristics. These nanocrystals displayed bright red color on excitation under 254 nm UV source. The main emission peak was assigned to the transition [⁵D₀→⁷F₂] at 615 nm. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) studies were carried out to understand surface morphological features and the particle size. Crystal structures of the nanocrystals were investigated by the X-ray diffraction (XRD) technique. The crystallite size of the as-prepared nanocrystals was around 29 nm, which was evaluated from the broad XRD peaks. The crystallite size increased to ∼45 nm on further heat treatment at 1000 °C.     

Synthesis of Y2Si2O7:Eu nanocrystal and its optical properties

Nanocrystalline Y₂Si₂O₇:Eu phosphor with an average size about 60 nm is easily prepared using silica aerogel as raw material under ultrasonic irradiation and annealing temperature at 300-600 °C and this nanocrystalline decomposes into Y₂O₃:Eu and silica by heat treatment at 700-900 °C. The excitation broad band centered at 283 and 254 nm results from Eu³⁺ substituting for Y³⁺ in Y₂Si₂O₇ and Y₂O₃/SiO₂, respectively. Compared with Y₂O₃:Eu/SiO₂ crystalline, the PL excitation and emission peaks of Y₂Si₂O₇:Eu nanocrystalline red-shift and lead to the enhance of its luminescence intensity due to the different chemical surroundings of Eu³⁺ in above nanocrystallines. The decrease of PL intensity may be ascribed to quenching effect resulting from more defects in Y₂O₃:Eu/SiO₂ crystalline.     

Nd3+掺杂的氧化镧钇透明激光陶瓷的光谱性能研究

采用传统无压烧结工艺制备了Nd³⁺掺杂的Y_2-2xLa_2xO₃(x=0.08)透明陶瓷并对其光谱性能进行了研究. 结果表明：Nd³⁺:Y_1.84La_0.16O₃透明陶瓷在780—850 nm的波长范围内有较宽的吸收带. 当Nd³⁺掺杂量为1.5at%时，在820 nm和激光二极管抽运的808 nm处的吸收截面分别为σ_abs(820 nm)=1.81×10^-20 cm²，σ_abs(808 nm)=1.54×10^-20 cm². 最强的发射峰位于1078 nm处，并具有荧光寿命长、发射带宽宽、量子效率高等特点. 加入La₂O₃后，基质的光谱品质参数X_Nd由1.6减小到0.46，因此和⁴F_3/2—⁴I_11/2跃迁相对应的荧光分支比β_J,11/2增大为56.82%. Nd³⁺:Y_1.84La_0.16O₃透明陶瓷的这些性质有利于高效率的激光输出和超短锁模激光脉冲的实现. 关键词： 氧化镧钇透明陶瓷 光谱性能 3+')" href="#">Nd³⁺     

Study on the photocatalytic activity of K2La2Ti3O10 doped with zinc(Zn)

The layered perovskite type oxides, K₂La₂Ti₃O₁₀ and zinc(Zn)-doped K₂La₂Ti₃O₁₀ were prepared by sol-gel method and were characterized by power X-ray diffraction, UV-vis diffuse reflectance and X-ray photoelectron spectroscopy. The photocatalytic activity for water splitting of the catalyst powders was investigated with I⁻ as electron donor under ultraviolet and visible light irradiation respectively. The electronic structure of the powders has been analyzed by the first principles calculation, which reveals the photo responses in the visible region and the improvement of the photocatalytic activity of K₂La₂Ti₃O₁₀. Conclusions were made that zinc(Zn)-doped K₂La₂Ti₃O₁₀ exhibited higher reactivity for hydrogen production. When I⁻ was used as electron donor, the optimum doping concentration of zinc(Zn) was found to be 0.015:1 (n_Zn:n_Ti). The average hydrogen production rates were 126.6 μmol/(gcat h) under ultraviolet irradiation and 55.5 μmol/(gcat h) under visible light irradiation which were raised by 131% and 251% compared with undoped K₂La₂Ti₃O₁₀ photocatalyst, respectively.     

Effect of concentration on the luminescence of Eu ions in nanocrystalline La2O3

Nanocrystalline powders with various Eu³⁺ concentration (from 1 to 10 mol %) doped La₂O₃ were prepared via a combustion route. Their structure and morphology were characterized using X-ray diffraction (XRD) and High-resolution transmission electron microscopy. The emission spectra of the as-synthesized samples show that the strongest emission position is centered at 626 nm corresponding to ⁵D₀→⁷F₂ transition of Eu³⁺ ions and the intensity change of 626 nm emission is considered as a function of ultraviolet (240 nm) irradiation time. The excitation spectra at 626 nm monitoring indicate that the charge transfer state band is varies with different Eu³⁺ ion concentration. These results are attributed to the surface defects of the nanocrystals.     

Spectral properties of Nd-doped Sr3Ga2Ge4O14 crystal

Neodymium doped strontium gallogermanate crystals were grown successfully by the Bridgman technique. The linear thermal expansion coefficients for the c- and a-axes were measured as 5.8 × 10⁻⁶ °C⁻¹ and 6.5 × 10⁻⁶ °C⁻¹. Absorption spectra, and fluorescence spectra, as well as fluorescence decay curves of Nd³⁺-doped Sr₃Ga₂Ge₄O₁₄ crystal, have been recorded at room temperature and used to calculate the absorption and stimulated emission cross-sections. Based on the Judd-Ofelt theory, three intensity parameters were obtained. The luminescent quantum efficiency of the ⁴F_3/2 level was determined to be approximately 73.8% for this material. Compared with other Nd³⁺-doped laser crystals, Nd³⁺-doped Sr₃Ga₂Ge₄O₁₄ crystal displays special laser properties due to its disorder structure.     

Effect of Eu,Tb codoping on the luminescent properties of Y2O3 nanorods

Red-emitting Y₂O₃:Eu³⁺ and green-emitting Y₂O₃:Tb³⁺ and Y₂O₃:Eu³⁺, Tb³⁺ nanorods were synthesized by hydrothermal method. Their structure and micromorphology have been analyzed by X-ray powder diffraction (XRD) and transmission electron microscopy (TEM). The photoluminescence (PL) property of Y₂O₃:Eu³⁺,Tb³⁺ phosphor was investigated. In the same host (Y₂O₃), upon excitation with ultraviolet (UV) irradiation, it is shown that there are strong emissions at around 610 and 545 nm corresponding to the forced electric dipole ⁵D₀-⁷F₂ transition of Eu³⁺ and ⁵D₄-⁷F₅ transition of Tb³⁺, respectively. Different qualities of Eu³⁺and Tb³⁺ ions are induced into the Y₂O₃ lattice. From the excitation spectrum, we speculate that there exists energy transfer from Tb³⁺ to Eu³⁺ ions .The emission color of powders reveals regular change in the separation of light emission. These powders can meet with the request of optical display material for different colors or can be potentially used as labels for biological molecules.     

Structural and optical properties of Er, Yb co-doped Y2O3 thin films

Thin Er³⁺, Yb³⁺ co-doped Y₂O₃ films were grown on (1 0 0) YAG substrates by pulsed laser deposition. Ceramic targets having different active ion concentration were used for ablation. The influence of the rare-earth content and oxygen pressure applied during the deposition on the structural, morphological and optical properties of the films were investigated. The films deposited at the lower pressure, 1 Pa, and at 1/10 Er to Yb doping ratio are highly textured along the (1 1 1) direction of the Y₂O₃ cubic phase. In addition to the crystalline structure, these films possess smoother surface compared to those prepared at the higher pressure, 10 Pa. All other films are polycrystalline, consisting of cubic and monoclinic phases of Y₂O₃. The rougher surface of the films produced at the higher-pressure leads to higher scattering losses and different behavior of the reflectivity spectra. Optical anisotropy in the films of less than 0.004 was measured regardless of the monoclinic structure obtained. Waveguide losses of about 1 dB/cm at 633 nm were obtained for the films produced at the lower oxygen pressure.     

Spectral properties of Nd<Superscript>3+</Superscript> ions in samples of transparent Y<Subscript>2</Subscript>O<Subscript>3</Subscript> ceramics

The spectral and luminescent characteristics of samples of Y₂O₃:Nd³⁺ ceramics obtained from different precursors under different preparation conditions (the concentration of an HfO₂ compacting additive, the temperature and time of synthesis) are studied at 300 and 77 K. It is shown that the spectral positions of absorption and luminescence lines of ceramics correspond to those of a Y₂O₃:Nd³⁺ single crystal. At the same time, the absorption and luminescence spectra show an inhomogeneous broadening, characteristic of disordered crystals and glass. The energies of the ⁴ I _9/2 and ⁴ F _3/2 Stark states of the Nd³⁺ ion are calculated. The calculation results nearly coincide with the data from the literature for the Y₂O₃:Nd³⁺ single crystal and transparent ceramics. Samples containing the compacting additive show additional lines, whose intensities correlate with its concentration and the method of preparation of Y₂O₃:Nd³⁺ ultradispersed powders. It is assumed that these lines are related to the fact that either Nd³⁺ ions enter the composition of the HfO₂ compacting additive or Hf⁴⁺ ions are present in the nearest environment of Nd³⁺ ions at the boundaries of granules enriched with HfO₂.     

High heat generation ability in AC magnetic field for nano-sized magnetic Y3Fe5O12 powder prepared by bead milling

Nano-sized magnetic Y₃Fe₅O₁₂ ferrite having a high heat generation ability in an AC magnetic field was prepared by bead milling. A commercial powder sample (non-milled sample) of ca. 2.9 μm in particle size did not show any temperature enhancement in the AC magnetic field. The heat generation ability in the AC magnetic field improved with a decrease in the average crystallite size for the bead-milled Y₃Fe₅O₁₂ ferrites. The highest heat ability in the AC magnetic field was for the fine Y₃Fe₅O₁₂ powder with a 15-nm crystallite size (the samples were milled for 4 h using 0.1 mm? beads). The heat generation ability of the excessively milled Y₃Fe₅O₁₂ samples decreased. The main reason for the high heat generation property of the milled samples was ascribed to an increase in the Néel relaxation of the superparamagnetic material. The heat generation ability was not influenced by the concentration of the ferrite powder. For the samples milled for 4 h using 0.1 mm? beads, the heat generation ability (W g⁻¹) was estimated using a 3.58×10⁻⁴ fH² frequency (f/kHz) and the magnetic field (H/kA m⁻¹), which is the highest reported value of superparamagnetic materials.