AlN缓冲层对ZnO薄膜质量的影响

采用脉冲激光沉积法以AlN为缓冲层在Si(100)衬底上制备了ZnO薄膜,并测量了样品的XRD谱、SEM图和PL谱.结果表明,AlN缓冲层可以提高Si衬底上外延生长ZnO薄膜的晶体质量.改变缓冲层的生长温度(50～500 ℃)所制备样品的测量结果表明,较低温度下生长的AlN缓冲层有利于制备高质量的ZnO外延层薄膜,其中AlN缓冲层生长温度为100 ℃时外延生长ZnO薄膜晶体质量最好.     

High resolution X-ray diffraction of GaN grown on Si (1 1 1) by MOVPE

High temperature GaN layers have been grown on Si (1 1 1) substrate by metalorganic vapor phase epitaxy (MOVPE). AlN was used as a buffer layer and studied as a function of thickness and growth temperature. The growth was monitored by in situ laser reflectometry. High resolution X-ray diffraction (HRXRD) revealed that optimized monocrystalline GaN was obtained for a 40 nm AlN grown at 1080 °C. This is in good agreement with the results of morphological study by scanning electron microscopy (SEM) and also confirmed by atomic force microscopy (AFM) observations. The best morphology of AlN with columnar structure and lower rms surface roughness is greatly advantageous to the coalescence of the GaN epilayer. Symmetric and asymmetric GaN reflections were combined for twist and stress measurements in monocrystalline GaN. It was found that mosaicity and biaxial tensile stress are still high in 1.7 μm GaN. Curvature radius measurement was also done and correlated to the cracks observations over the GaN surface.     

Effect of annealing temperature and annealing atmosphere on the structure and optical properties of ZnO thin films on sapphire (0 0 0 1) substrates by magnetron sputtering

ZnO thin films were epitaxially grown on sapphire (0 0 0 1) substrates by radio frequency magnetron sputtering. ZnO thin films were then annealed at different temperatures in air and in various atmospheres at 800 °C, respectively. The effect of the annealing temperature and annealing atmosphere on the structure and optical properties of ZnO thin films are investigated by X-ray diffraction (XRD), atomic force microscopy (AFM), photoluminescence (PL). A strong (0 0 2) diffraction peak of all ZnO thin films shows a polycrystalline hexagonal wurtzite structure and high preferential c-axis orientation. XRD and AFM results reveal that the better structural quality, relatively smaller tensile stress, smooth, uniform of ZnO thin films were obtained when annealed at 800 °C in N₂. Room temperature PL spectrum can be divided into the UV emission and the Visible broad band emission. The UV emission can be attributed to the near band edge emission (NBE) and the Visible broad band emission can be ascribed to the deep level emissions (DLE). By analyzing our experimental results, we recommend that the deep-level emission correspond to oxygen vacancy (V_O) and interstitial oxygen (O_i). The biggest ratio of the PL intensity of UV emission to that of visible emission (I_NBE/I_DLE) is observed from ZnO thin films annealed at 800 °C in N₂. Therefore, we suggest that annealing temperature of 800 °C and annealing atmosphere of N₂ are the most suitable annealing conditions for obtaining high quality ZnO thin films with good luminescence performance.     

Porous AlN films grown on C-face SiC by hydride vapor phase epitaxy

We report the growth of porous AlN films on C-face SiC substrates by hydride vapor phase epitaxy (HVPE). The influences of growth condition on surface morphology, residual strain and crystalline quality of AlN films have been investigated. With the increase of the V/III ratio, the growth mode of AlN grown on C-face 6H-SiC substrates changes from step-flow to pit-hole morphology. Atomic force microscopy (AFM), scanning electron microscopy (SEM) and Raman analysis show that cracks appear due to tensile stress in the films with the lowest V/III ratio and the highest V/III ratio with a thickness of about 3 μm. In contrast, under the medium V/III ratio growth condition, the porous film can be obtained. Even when the thickness of the porous AlN film is further increased to 8 μm, the film remains porous and crack-free, and the crystal quality is improved.     

Defects, stress and abnormal shift of the (0 0 2) diffraction peak for Li-doped ZnO films

The effect of changes in Li content on the structural property of sol-gel Li-doped ZnO films was investigated in this study. The observed changes of the Li incorporation-induced strain along c-axis are closely related to the different ratios between the concentrations of Li interstitials (Li_i) and Li substituting for Zn (Li_Zn) in the films. According to the observed results from X-ray diffraction (XRD) and photoluminescence measurements, we found that the domination of the dissociative mechanism in the Li-doped ZnO films led to transformation from Li_Zn to Li_i, involving the formation of Zn vacancies (V_Zn). In addition, the interaction between these defects (that is, Li_Zn, Li_i, V_Zn and oxygen vacancy) and the crystal structure may lead to the abnormal shift of the (0 0 2) diffraction peak position determined from XRD measurements.     

Morphology and photoluminescence of ultrasmall size of Ge quantum dots directly grown on Si(0 0 1) substrate

High density and ultrasmall size of Ge quantum dots (QDs) have been achieved directly on Si(0 0 1) (2 × 1) reconstruction surface. Their detailed morphology was observed by atomic force microscope (AFM) and shows that small pyramids, small domes, huts, and multi-headed large domes coexist in the film grown at 400 °C, while small domes and multi-headed large domes formed at 450 °C. Their low temperature photoluminescence (PL) showed that a very strong non-phonon (NP) peak with a large blue shift of 0.19 eV at 14 K, which can be attributed to their very high areal density, 5.2 × 10¹¹ cm⁻², and sub-10-nm mean size, 7.6 ± 2.3 nm.     

Homogeneous Si films on CaF2/Si(1 1 1) due to boron enhanced solid phase epitaxy

The structure and morphology of Si/CaF₂/Si(1 1 1) structures have been investigated by X-ray diffraction (XRD, GIXRD) and X-ray photoelectron spectroscopy (XPS). While CaF₂ films were grown via molecular beam epitaxy (MBE), Si films on CaF₂/Si(1 1 1) are fabricated by surfactant enhanced solid phase epitaxy (SE-SPE). Here Boron was used as a surfactant to obtain semiconductor films of homogeneous thickness. The Si films are entirely relaxed while the CaF₂ films have both pseudomorphic and relaxed crystallites. After exposure to ambient conditions, the Si films have a very thin native oxide film. The homogeneous Si film partially prevents the incorporation of impurities at the interface between the Si substrate and CaF₂ via migration along residual defects of the CaF₂ film.     

Crystal growth of SrTiO3 films on H-terminated Si(1 1 1) with SrO buffer layers

Growth of epitaxial SrTiO₃ (STO) films has been examined on H-terminated Si(1 1 1) with SrO buffer layers. The epitaxial SrO buffer layers have reduced stress on H-terminated Si substrates. On the SrO buffer layers, the STO films grow epitaxially with triple domains at low temperature. Each STO domain has equivalent epitaxial relationship to SrO buffer layers, STO(1 1 0)∥SrO(1 1 1) and .     

A nanoindentation study of the mechanical properties of ZnO thin films on (0 0 0 1) sapphire

The mechanical properties of epitaxial ZnO thin films grown on (0 0 0 1) sapphire substrate were investigated by nanoindentation with a Berkovich tip and compared with that of bulk ZnO single crystal. In all indents on ZnO film a single discontinuity (‘pop-in’) in the load versus indentation depth data was observed at a specific depth of between 13 and 16 nm. In bulk ZnO, however only 65% of indents showed pop-in event at a specific depth of between 12 and 20 nm. The mechanism responsible for the ‘pop-in’ event in the epitaxial ZnO thin films as well as in bulk ZnO was attributed to the sudden propagation of dislocations, which had been pinned down by pre-existing defects, along the pyramidal and basal {0 0 0 1} planes (cross slip). The elastic modulus and hardness of the epitaxial ZnO thin films were determined to be 154 ± 5 and 8.7 ± 0.2 GPa, respectively, at an indentation depth of 30 nm.     

Surface morphology and optical properties of ZnO epilayers grown on Si(1 1 1) by metal organic chemical vapor deposition

Heteroepitaxial ZnO epilayers were grown on Si(1 1 1) substrates using a vertical geometry atmospheric pressure metal organic chemical vapor deposition (AP-MOCVD) system. The growth temperature was varied from 550 °C to 650 °C in steps of 25 °C. The ZnO growth rate and surface morphology were strong functions of the growth temperature and ranged from ∼0.16 μm/h to 1.36 μm/h. The surface morphology of the ZnO films changed from granular to sharp tips as the growth temperature increased. The effect of buffer thickness was also examined, and was found to have a strong effect on the optical properties of the ZnO. An optimized growth condition for ZnO epilayers was found at 625 °C, producing a FWHM in the room temperature photoluminescence (PL) spectrum of 4.5 nm and a preferred growth orientation along the (0 0 2) direction.Transmission electron microscopy images and selected area diffraction patterns showed excellent crystalline quality of both the buffer and ZnO overlayer. When non-optimized growth temperatures were employed, post-growth annealing was found to greatly enhance the ratio of band-edge to deep level emission.     

Electron and lattice structure of ultra thin Ag films on Si(1 1 1) and Si(0 0 1)

We studied the low temperature (T ? 130 K) growth of Ag on Si(0 0 1) and Si(1 1 1) flat surfaces prepared by Si homo epitaxy with the aim to achieve thin metallic films. The band structure and morphology of the Ag overlayers have been investigated by means of XPS, UPS, LEED, STM and STS. Surprisingly a (√3 × √3)R30° LEED structure for Ag films has been observed after deposition of 2-6 ML Ag onto a Si(1 1 1)(√3 × √3)R30°Ag surface at low temperatures. XPS investigations showed that these films are solid, and UPS measurements indicate that they are metallic. However, after closer STM studies we found that these films consists of sharp Ag islands and (√3 × √3)R30°Ag flat terraces in between. On Si(0 0 1) the low-temperature deposition yields an epitaxial growth of Ag on clean Si(0 0 1)-2 × 1 with a twinned Ag(1 1 1) structure at coverage’s as low as 10 ML. Furthermore the conductivity of few monolayer Ag films on Si(1 0 0) surfaces has been studied as a function of temperature (40-300 K).     

Effects of sic buffer layer on the optical properties of ZnO films grown on Si (1 1 1) substrates

ZnO films have been grown by a sol-gel process on Si (1 1 1) substrates with and without SiC buffer layers. The influence of SiC buffer layer on the optical properties of ZnO films grown on Si (1 1 1) substrates was investigated. The intensity of the E₂ (high) phonon peak in the micro-Raman spectrum of ZnO film with the SiC buffer layer is stronger than that of the sample without the SiC buffer layer, and the breadth of E₂ (high) phonon peak of ZnO film with the SiC buffer layer is narrower than that of the sample without the SiC buffer layer. These results indicated that the crystalline quality of the sample with the SiC buffer layer is better than that of the sample without the SiC buffer layer. In photoluminescence spectra, the intensity of free exciton emission from ZnO films with the SiC buffer was much stronger than that from ZnO film without the SiC buffer layer, while the intensity of deep level emission from sample with the SiC buffer layer was about half of that of sample without the SiC buffer layer. The results indicate the SiC buffer layer improves optical qualities of ZnO films on Si (1 1 1) substrates.     

Metal organic chemical vapor deposition of ultrathin ZrO2 films on Si(1 0 0) and Si(1 1 1) studied by electron spectroscopy

The growth of ultrathin ZrO₂ films on Si(1 0 0)-(2 × 1) and Si(1 1 1)-(7 × 7) has been studied with core level photoelectron spectroscopy and X-ray absorption spectroscopy. The films were deposited sequentially by chemical vapor deposition in ultra-high vacuum using zirconium tetra-tert-butoxide as precursor. Deposition of a > 50 Å thick film leads in both cases to tetragonal ZrO₂ (t-ZrO₂), whereas significant differences are found for thinner films. On Si(1 1 1)-(7 × 7) the local structure of t-ZrO₂ is not observed until a film thickness of 51 Å is reached. On Si(1 0 0)-(2 × 1) the local geometric structure of t-ZrO₂ is formed already at a film thickness of 11 Å. The higher tendency for the formation of t-ZrO₂ on Si(1 0 0) is discussed in terms of Zr-O valence electron matching to the number of dangling bonds per surface Si atom. The Zr-O hybridization within the ZrO₂ unit depends furthermore on the chemical composition of the surrounding. The precursor t-butoxy ligands undergo efficient C-O scission on Si(1 0 0), leaving carbonaceous fragments embedded in the interfacial layer. In contrast, after small deposits on Si(1 1 1) stable t-butoxy groups are found. These are consumed upon further deposition. Stable methyl and, possibly, also hydroxyl groups are found on both surfaces within a wide film thickness range.     

Spectral behavior of the emission around 3.31 eV (A-line) from ZnO nanocrystals

The emission at around 3.31 eV (A-line) from three types of ZnO nanocrystals with different particle sizes (10-1000 nm) was studied. The photoluminescence (PL) measurements were performed under different excitation densities and at different temperatures. The A-line emission exhibited a strong dependence on temperature and excitation power density. With increasing excitation density and temperature overlapping of the closely spaced first longitudinal optical (LO) phonon replica of free excitons by the A-line emission was observed.     

Thin PTCDA films on Si(0 0 1): 1. Growth mode

We have studied the interface and thin film formation of the organic molecular semiconductor 3,4,9,10 perylene tetracarboxylic dianhydride (PTCDA) on clean and on hydrogen passivated Si(0 0 1) surfaces. The studies were made by means of high resolution X-ray photoelectron spectroscopy (HRXPS), near edge X-ray absorption fine structure (NEXAFS), low energy electron diffraction (LEED), and atomic force microscopy (AFM). On the passivated surface the LEED pattern is somewhat diffuse but reveals that the molecules grow in several ordered domains with equivalent orientations to the substrate. NEXAFS shows that the molecules are lying flat on the substrate. The Si 2p XPS line shape is not affected when the film is deposited so it can be concluded that the interaction at the interface between PTCDA and the substrate is weak. The evolution of the film formation appears to be homogeneous for the first monolayer with a nearly complete coverage of flat lying molecules based on the XPS attenuation. For layer thickness of 0.5-2 monolayers (ML) the molecules start to form islands, attracting the molecules in between, leaving the substrate partly uncovered. For thicker films there is a Stranski-Krastanov growth mode with thick islands and a monolayer thick film in between. For the clean surface the ordering of the film is much lower and angle resolved photoelectron spectroscopy (ARPES) of the molecular orbitals have only a small dependence of the emission angle. NEXAFS shows that the molecules do not lie flat on the surface and also reveal a chemical interaction at the interface.     

Computational study of adsorption, diffusion, and dissociation of precursor species on the GaN (0 0 0 1) surface during GaN MOCVD

The adsorption, diffusion, and dissociation of precursor species, MMGa (monomethylgallium) and NH₃, on the GaN (0 0 0 1) surface have been investigated using the DFT (density functional theory) calculation combined with a GaN (0 0 0 1) surface cluster model. The energetics of NH₃(ad) dissociation on the surface proposed of NH₃(ad) via NH₂(ad) to NH(ad) was facile with small activation barriers. A combined analysis with surface diffusion of adatoms demonstrated Ga(ad) and NH(ad) become primary reactant species for 2D film growth, and N(ad) develops into a nucleation center. Our studies suggest the control of NH₃(ad) dissociation are essential to improve epitaxial film quality as well as Ga-rich condition. In addition, the adsorbability of H(ad)s resulted from NH₃(ad) dissociation were found to influence on the surface chemistry during film growth.     

ZnO／AlN／Si（111）薄膜的外延生长和性能研究

用常压金属化学气相沉积法(MOCVD)在Si(111)衬底上制备了马赛克结构ZnO单晶薄膜。引入低温Al N缓冲层以阻止衬底氧化、缓解热失配和晶格失配。薄膜双晶X射线衍射2θ/ω联动扫描只出现了Si(111)、ZnO(000l)及Al N(000l)的衍射峰。ZnO/Al N/Si(111)薄膜C方向晶格常量为0.5195nm,表明在面方向处于张应力状态;其对称(0002)面和斜对称(1012)面的双晶X射线衍ω摇摆曲线半峰全宽分别为460″和1105″;干涉显微镜观察其表面有微裂纹,裂纹密度为20cm-1;3μm×3μm范围的原子力显微镜均方根粗糙度为1.5nm;激光实时监测曲线表明薄膜为准二维生长,生长速率4.3μm/h。低温10K光致发光光谱观察到了薄膜的自由激子、束缚激子发射及它们的声子伴线。所有结果表明,采用金属化学气相沉积法并引入Al N为缓冲层能有效提高Si(111)衬底上ZnO薄膜的质量。     

FEM simulation of Rayleigh waves for CMOS compatible SAW devices based on AlN/SiO2/Si(1 0 0)

A simulation study of Rayleigh wave devices based on a stacked AlN/SiO₂/Si(1 0 0) device was carried out. Dispersion curves with respect to acoustic phase velocity, reflectivity and electromechanical coupling efficiency for tungsten W and aluminium Al electrodes and different layer thicknesses were quantified by 2D FEM COMSOL simulations. Simulated acoustic mode shapes are presented. The impact of these parameters on the observed Rayleigh wave modes was discussed. High coupling factors of 2% and high velocities up to 5000 m/s were obtained by optimizing the AlN/SiO₂ thickness ratio.     

Influence of AlN buffer layer thickness on structural properties of GaN epilayer grown on Si (111) substrate with AlGaN interlayer

We present the growth of GaN epilayer on Si (111) substrate with a single AlGaN interlayer sandwiched between the GaN epilayer and AlN buffer layer by using the metalorganic chemical vapour deposition. The influence of the AlN buffer layer thickness on structural properties of the GaN epilayer has been investigated by scanning electron microscopy, atomic force microscopy, optical microscopy and high-resolution x-ray diffraction. It is found that an AlN buffer layer with the appropriate thickness plays an important role in increasing compressive strain and improving crystal quality during the growth of AlGaN interlayer, which can introduce a more compressive strain into the subsequent grown GaN layer, and reduce the crack density and threading dislocation density in GaN film.     

Self-limiting growth of ZnO films on (0 0 0 1) sapphire substrates by atomic layer deposition at low temperatures using diethyl-zinc and nitrous oxide

Atomic layer deposition (ALD) of zinc oxide (ZnO) films on (0 0 0 1) sapphire substrates was conducted at low temperatures by using diethyl-zinc (DEZn) and nitrous oxide (N₂O) as precursors. It was found that a monolayer-by-monolayer growth regime occurred at 300 °C in a range of DEZn flow rates from 5.7 to 8.7 μmol/min. Furthermore, the temperature self-limiting process window for the ALD-grown ZnO films was also observed ranging from 290 to 310 °C. A deposition mechanism is proposed to explain how saturated growth of ZnO is achieved by using DEZn and N₂O. Transmission spectroscopic studies of the ZnO films prepared in the self-limiting regime show that the transmittances of ZnO films are as high as 80% in visible and near infrared spectra. Experimental results indicate that ZnO films with high optical quality can be achieved by ALD at low temperatures using DEZn and N₂O precursors.