Some aspects of matrix-assisted laser desorption/ionization analysis of hemoglobin from whole human blood

Some aspects of the matrix-assisted laser desorption/ionization (MALDI) method in the analysis of hemoglobin from whole human blood are described. These aspects are: sensitivity of this method, fragmentation of hemoglobin ions, and influence of some impurities (sodium chloride NaCl, sodium sulfate Na2SO4, and potassium ferrocyanide K4Fe(CN)6) on the detection process. As a matrix, alpha-cyano-4-hydroxycinnamic acid (CCA) was used. The estimated maximum concentrations of tested salts for which no hemoglobin signal was observed were determined.     

Selection of internal standards for quantitative analysis by matrix-assisted laser desorption-ionization (MALDI) time-of-flight mass spectrometry

 The selection of an appropriate internal standard (IS) for quantification by matrix-assisted laser desorption/ionization (MALDI) mass spectrometry is critical for the successful application of quantitative MALDI. Selection of the IS depends on the chemical similarity of the analyte and IS and the mass separation of the analyte and IS as a function of instrumental peak resolution. For the quantification of bovine insulin, a series of internal standards including horse heart cytochrome C, bovine insulin chain B, des-pentapeptide human insulin, and des-octapeptide porcine insulin was investigated. Des-pentapeptide human insulin was found to be the most appropriate internal standard (relative standard deviation of the standard curve slope=2.99%, correlation coefficient=0.988 in the range of 0.5–0.4 μmol/L). Two methods for measuring of the MALDI signal intensity were evaluated, direct peak integration following subtraction of a linear background and non-linear least squares curve fitting. The results obtained with these methods were equivalent. Received: 10 November 1995 / Revised: 4 March 1996 / Accepted: 6 March 1996     

Specific adsorption of anions preceding the dissolution of CuO in acidic solution

The specific adsorption of sulfate and chloride ions on powdered CuO was studied by radiotracer techniques in acidified of 0.5 mol dm^–3 NaClO₄ supporting electrolyte. It was found that the pH and concentration dependence of the adsorption of labelled sulfates could be determined over a wide pH range (2.0≤pH≤7.0), despite the gradual dissolution of the copper oxide. No specific adsorption was found at pH≥7.0. It was postulated that the specific adsorption was preceded by the protonation of the CuO surface. No reliable relationships were found for labelled chlorides, owing to the relatively high desorption rate of the surface complexes formed in the sorption process. The apparent adsorbability of sulfate ions was significantly higher than that of the chloride ions, as shown by the results of competitive adsorption of the two species. This observation was in agreement with the postulated lower desorption rate of the surface complex formed with sulfates than that of species formed with chlorides. Electronic Publication     

A new route of oxygen isotope exchange in the solid phase: demonstration in CuSO4.5H2O

Temperature-programmed desorption mass spectrometry (TPD-MS) measurements on [(18)O]water-enriched copper sulfate pentahydrate (CuSO(4).5H(2)(18)O) reveal an unambiguous occurrence of efficient oxygen isotope exchange between the water of crystallization and the sulfate in its CuSO(4) solid phase. To the best of our knowledge, the occurrence of such an exchange was never observed in a solid phase. The exchange process was observed during the stepwise dehydration (50-300 degrees C) of the compound. Specifically, the exchange promptly occurs somewhere between 160 and 250 degrees C; however, the exact temperature could not be resolved conclusively. It is shown that only the fifth, sulfate-associated, anionic H(2)O molecule participates in the exchange process and that the exchange seems to occur in a preferable fashion with, at the most, one oxygen atom in SO(4). Such an exchange, occurring below 250 degrees C, questions the common conviction of unfeasible oxygen exchange under geothermic conditions. This new oxygen exchange phenomenon is not exclusive to copper sulfate but is unambiguously observed also in other sulfate- and nitrate-containing minerals.     

Role of the support material on laser desorption/ionization mass spectra

We report the results of experimental studies on the effects of sample supports in laser desorption/ionization mass spectrometry (LDI-MS). LDI time-of-flight (TOF) mass spectra obtained for C(60) and insulin samples deposited onto standard stainless steel substrate and/or onto some non-metallic materials (glass, scotch tape, floppy disc foil, Teflon foil, photocopy film), all recorded under identical, typical experimental conditions, have been compared with regard to their intensity and quality. The LDI investigations show that compared with stainless steel, glass and floppy disc foil sample supports boost (2-3.5 times) ion yields for C(60)(+) and C(60)(-) ions, respectively. The stainless steel and scotch tape sample supports are the best for the mass resolution of positive ions and the formation of (C(60))(n)(-) (n 相似文献   

Simultaneous quantitative determination of insulin aspart and insulin degludec in human plasma using simple shoot LC method

Combining short-acting and long-acting insulin analogs was a real challenge that was overcome by NovoNordisk through the co-formulation of insulin aspart and insulin degludec in single-dosage form. The proposed study provides a simple, short, and reliable HPLC method with diode array detection that is developed and validated for the simultaneous determination of insulin aspart and insulin degludec in human plasma. The proposed method achieved good separation between the two analytes utilizing a C8 column at 35°C in a very short run time (6 min), with a simple, low-cost, and reliable extraction method through precipitation of plasma protein. Gradient elution was applied using a mobile phase consisting of 0.1 M sodium sulfate (pH 3.4) and acetonitrile. The method was validated according to EMA Guideline on Bioanalytical Validation. The proposed method had a linear range from 3.0 to 300 μg/mL for insulin aspart and from 3.5 to 300 μg/mL for insulin degludec. The intra- and inter-day precision of insulin aspart were 0.36–3.33% and 1.59–8.84%, respectively, and accuracy was between 10.06 and 3.09% The intra- and inter-day precision of insulin degludec were 0.29–1.93% and 0.89–5.14%, respectively, and accuracy was between −5.29 and 3.91%.     

Chromatographic determination of nitrophenols in aqueous media after two-stage preconcentration using an N-vinylpyrrolidone-based polymer

Two-stage procedures for the preconcentration of nitrophenols (4-nitrophenol, 2,4- and 2,5-dinitrophenol, and 2,4,6-trinitrophenol) from aqueous solutions are proposed. At the first stage, the preconcentration and desorption of nitrophenols under dynamic conditions is carried out. At the second stage, depending on the nature of the desorption solution, the eluate is evaporated (acetonitrile) or saturated with ammonium sulfate and extracted with acetone (aqueous NH₃ solution). The concentration factors are 4000 and 910, respectively. Nitrophenols are determined in concentrates by thin layer chromatography and HPLC, the limits of detection are 1.0–1.8 and 0.25–0.45 μg/L, respectively. The duration of analysis is 200 min.     

Fabrication and properties of pH-sensitive nanostructured polyelectrolyte microparticles loaded with insulin

Thorough investigation and comparative study were conducted for insulin-loaded microparticles fabricated by consecutive adsorption of polyanions (dextran sulfate and chitosan sulfate) and polycations (chitosan and protamine) onto protein microaggregates. The possible regulation of insulin release from the particles by variation in polyelectrolyte pairs, in the number of their adsorption cycles and in pH of media was demonstrated. For all studied cases the microparticles showed protective action towards insulin inactivation at acid pH values and protein release at pH > 5, corresponding to human gastro-intestinal conditions.     

The role of the cation in the oxygen isotopic exchange in crystalline sulfate salt hydrates

The oxygen isotopic exchange during dehydration and decomposition of five sulfate salt hydrates (CoSO₄·6H₂O, NiSO₄·7H₂O, ZnSO₄·7H₂O, CaSO₄·2H₂O, Li₂SO₄·H₂O) was studied in detail by temperature programmed desorption mass spectrometry (TPD-MS) in a supersonic molecular beam (SMB) inlet mode. Crystals of the ¹⁸O-enriched salts were grown and the detailed desorption steps of the various gaseous products released during dehydration and decomposition of these compounds were recorded. The desorption patterns confirmed the known characteristic stepwise dehydration of these salts, where regardless of the crystalline structure and composition, in all the salts (excluding the Li and Ca sulfates) a major group of n ? 1 loosely bounded water of crystallization molecules (out of total of n molecules in the fully hydrated form) are released at adjacent temperatures in a typical low temperature range (<200 °C), while the last, most strongly bounded water molecule, consistently desorbs at relatively higher temperatures (240 < T < 440 °C). Interestingly, it is established that the oxygen isotopic exchange occurs exclusively between that latter, most strongly bound water molecule, and the salt anion. Remarkably, the results point out that the exchange process is mostly of solid-solid nature. Finally, the results point out that the probability of the isotopic exchange increases with the increment in the desorption temperature of the last dehydration step, i.e. with the bond strength in the monohydrate, between the last water molecule of crystallization and the cation.     

Kinetics of the Formation of Nano-Sized Platinum Particles in Water-in-Oil Microemulsions

The association between low-charge-density polyelectrolytes adsorbed onto negatively charged surfaces (mica and silica) and an anionic surfactant, sodium dodecyl sulfate (SDS), has been investigated using surface force measurements, ellipsometry, and XPS. All three techniques show that the polyelectrolyte desorbs when the SDS concentration is high enough. The XPS study indicates that desorption starts at a SDS concentration of ca. 0.1 unit of cmc (8x10(-4) M) and that the desorption proceeds progressively as the SDS concentration is increased. Surface force measurements show that for the polyelectrolyte studied here, having 1% of the segments charged, the desorption proceeds without any swelling of the adsorbed layer. This behavior differs from that observed when polyelectrolytes of greater charge density are used. Copyright 2001 Academic Press.     

Properties of matrix-assisted laser desorption. Measurements with a time-to-digital converter.

Some properties of matrix-assisted laser desorption have been studied using single-ion-counting methods and a time-to-digital converter. The methods allow examination of the process for irradiances near the reported threshold for observation with a transient recorder. All measurements were made using bovine insulin as a test compound. We present direct evidence that an irradiance threshold near 10(6) W cm-2 exists for ion production, and that the process is a collective effect, either involving a large number of molecular ions (approximately 10(4) in a successful event or none at all. Above the threshold, the yield is found to scale with a high power (4th to 6th) of the irradiance. Measurements of initial velocity distributions indicate an axial velocity spread corresponding to approximately 50 eV and a radial velocity spread corresponding to approximately 2.4 eV. Thus the ejection or extraction mechanism appears to be strongly asymmetric.     

Structure of the asparagine-linked sugar chains of porcine kidney and human urine cerebroside sulfate activator protein

The specific sugar residues and their linkages in the oligosaccharides from pig kidney and human urine cerebroside sulfate activator proteins (saposin B), although previously hypothesized, have been unambiguously characterized. Exhaustive sequential exoglycosidase digestion of the trimethyl-p-aminophenyl derivatives, followed by either matrix-assisted laser desorption/ionization and/or mass spectrometry, was used to define the residues and their linkages. The oligosaccharides were enzymatically released from the proteins by treatment with peptidyl-N-glycosidase F and separated from the proteins by reversed-phase high-performance liquid chromatography (HPLC). Reducing termini were converted to the trimethyl-p-aminophenyl derivative and the samples were further purified by normal-phase HPLC. The derivatized carbohydrates were then treated sequentially with a series of exoglycosidases of defined specificity, and the products of each digestion were examined by mass spectrometry. The pentasaccharides from pig kidney and human urine protein were shown to be of the asparagine-linked complex type composed of mannose-alpha 1-6-mannose-beta 1-4-N-acetylglucosamine-N-acetylglucosamine(alpha 1-6-fucose). This highly degraded structure probably represents the final product of intra-lysosomal exoglycosidase digestion. Oligosaccharide sequencing by specific exoglycosidase degradation coupled with mass spectrometry is more rapid than conventional oligosaccharide sequencing. The procedures developed will be useful for sequencing other oligosaccharides including those from other members of the lipid-binding protein class to which cerebroside sulfate activator belongs. (c) 2000 John Wiley & Sons, Ltd.     

Microemulsion polymerization of styrene stabilized by sodium dodecyl sulfate and short‐chain alcohols

Styrene microemulsion polymerizations with different short‐chain alcohols [n‐C_iH_2i+1OH (C_iOH), where i = 4, 5, or 6] as the cosurfactant were investigated. Sodium dodecyl sulfate and sodium persulfate (SPS) were used as the surfactant and initiator, respectively. The desorption of free radicals out of latex particles played an important role in the polymerization kinetics. An Arrhenius expression for the radical desorption rate coefficient was obtained from the polymerizations at temperatures of 50–70 °C. The polymerization kinetics were not very sensitive to the alkyl chain length of alcohols compared with the temperature effect. The maximal polymerization rate in decreasing order was C₆OH > C₄OH > C₅OH. This was related to the differences in the water solubility of C_iOH and the structure of the oil–water interface. The feasibility of using a water‐insoluble dye to study the particle nucleation mechanisms was also evaluated. The parameters chosen for the study of the particle nucleation mechanisms include the cosurfactant type (C_iOH), the SPS concentration, and the initiator type (oil‐soluble 2,2′‐azobisisobutyronitrile versus water‐soluble SPS). © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3199–3210, 2001     

Desorption Potentials of Alkyl Alcohols and Specific Adsorption of Anions

Abstract

The potentials of desorption of various alkyl alcohols have been studied as a function of concentration of alcohol and of the nature and concentration of various electrolytes. Specific adsorption of the electrolyte ions is reflected in shifts of the desorption peaks of the alcohols. At anodic potentials, the order of specific adsorption appears to be chloride > sulfate >perchlorate > fluoride, and at cathodic potentials (vs. S. C. E.), chloride > perchlorate > sulfate > fluoride.     

Polyacrylamide Gel Electrophoresis of Insulin

Abstract

Four kinds of polyacrylamide gel electrophoresis (PAGE) were applied to insulin and peroxynitrite‐treated insulin. The Native‐PAGE had a better resolution than sodium dodecyl sulfate (SDS)‐PAGE, SDS‐urea‐PAGE, and even Tricine‐SDS‐PAGE. Reduction and nonreduction of insulin and peroxynitrite‐treated insulin in Native‐PAGE showed that four tyrosine residues in insulin molecular could be nitrated by peroxynitrite and that alkylation with iodoacetamide was better than no alkylation and alkylation with iodoacetic acid, which would introduce negative charges to the peptides. The method of Native‐PAGE was suitable to analysis of insulin and its analogs, even other peptides of low molecular weight.     

Effect of salts on synthesis of mesoporous materials with mixed cationic and anionic surfactants as templates

Mesoporous silica materials were synthesized using tetraеthoxysilane as precursor and liquid crystals formed in aqueous mixtures of cetyl trimethyl ammonium bromide (CTAB) and sodium dodecyl sulfate (SDS) as templates, without and with the addition of NaBr or Na₂SO₄. For this purpose, the formation of liquid crystals as a function of the ratio of CTAB and SDS under different conditions was studied. It was found that liquid crystals formed in the mixed system of CTAB and SDS at certain mixing ratios are well-structured templates for the synthesis of mesoporous silicas. The synthesized silica materials were characterized by transmission electron microscope and nitrogen adsorption/desorption analysis. The pore size of mesoporous silicas could be controlled between 3 to 6 nm by simply changing the concentration of NaBr in solution. The mesoporous silicas exhibited lamellar structure and the order of structural arrangement was promoted with addition of NaBr. However, addition of Na₂SO₄ led to ink-bottle type pores of mesoporous silica with a narrow pore size distribution of around 2 nm and a higher specific surface area of 610 m² g^–1.     

Distribution of water-soluble and surface-active low-molecular-weight species in acrylic latex films

Monodisperse core-shell latices were synthesized, differing in the acrylic acid (AA) content in the particle shell (1 or 4 wt%) and the Tg of the acrylic core (around -40 or 10 degrees C). In a first step, the drying mechanisms of the dialyzed latices were studied by confocal Raman spectroscopy. It was shown that, besides some unexpected features (briefly described in the article), drying occurred in a rather classical way, i.e., simultaneously from top to bottom and from edge to center. Then, the distributions of sulfate ion (SO4) (from sodium sulfate) and sodium dodecyl sulfate (SDS) in the dry latex films were established by confocal Raman spectroscopy and attenuated total reflectance (ATR). The two techniques were complementary. SO4 and SDS distributions were quite different, although presenting some common characteristics. In both cases, repartition of the low-molecular-weight species in the film was even less homogeneous when the AA content was lower and the particle core softer. However, SO4 showed enrichment at the film-substrate interface and depletion at the air side, whereas SDS showed concentration maxima at both interfaces. Interpretations stress the importance of desorption from the particle-water interface, transport by water, size effects, and diffusion.     

Interaction of radium with freshwater sediments and their mineral components

A radiotracer method was used for investigation of the adsorption and desorption of radium on stream sediments under conditions similar to those prevailing in waste and surface waters. The effects of pH, ionic strength and Ca²⁺ or SO ₄ ^2– ions were studied. The results were compared with analogous data characterizing radium interaction with model solids representing components of the sediments. It has been found that the adsorption affinity of the sediments for radium cannot be easily derived from their composition or other properties. No simple correlation with specific surface area, organic matter, oxidic coatings or other components of the sediments was observed. However, an exceptional role of barite (barium sulfate) in the sediments was noted. In the presence of sulfate ions (60 mg/l) this component was responsible for the uptake of predominant or at least significant part of radium, depending on the barite content of sediments. In the absence of added sulfate ions, the adsorption of radium at ph 5–9 on sediments containing barite was lower than on similar sediments without this component, indicating that other components may be more efficient in radium adsorption.     

Biphasic synthesis of colloidal mesoporous silica nanoparticles using primary amine catalysts

Evanescent wave-cavity ring-down spectroscopy (EW-CRDS) is employed to characterize micellization of anionic surfactants and the related capability of removing cationic substance off the silica surface. Crystal violet (CV(+)) cationic dye is used as a molecular probe to effectively determine critical hemimicelle concentration (HMC) of surfactants on the surface. The HMC results are 1×10(-2), 4×10(-3), 8×10(-4), and 2.5×10(-4) mol/L for sodium sulfate salts with a carbon-chain length of C-10, C-12, C-14, and C-16, respectively. A stronger hydrophobic interaction results in a less concentration required to undergo micellization. The HMC values on the surface are about half of those in solution. When NaCl solution is added, the electrolyte helps reduce the electrostatic repulsion between the anionic sulfate heads to facilitate the surfactant aggregation, and thus, the subsequent HMC is reduced. Furthermore, the probable phase change for dye-surfactant interactions on the surface at the concentration below HMC is observed, and the desorption rates of CV(+) are measured as a function of concentration and carbon-chain length of surfactants above HMC. Given each surfactant concentration at its respective HMC, the corresponding desorption rates are along the order of C-12相似文献   

Conformational analysis of sulfate species on Ag/Al2O3 by means of theoretical and experimental vibration spectra

The formation and configuration of sulfate species on Ag/Al2O3 were studied by means of in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) and density functional theory (DFT) calculations. The comparison between theoretical and experimental vibration spectra enable us to draw the following conclusions: Bidentate sulfate species rather than tridentate sulfate species are the predominant surface species on Ag/Al2O3. Moreover, both bidentate and tridentate sulfate species may coexist on the catalyst surface at a lower coverage. The accumulation of surface sulfate species could well explain the blue shift of the sulfate species in IR spectra. In addition, the in situ DRIFTS could distinguish between the sulfate species that linked to Al site and Ag site, which was well supported by temperature-programmed desorption (TPD) results.