Studies of closed orbit correction and slow orbit feedback for the SSRF storage ring

Details of the active ways to suppress Closed Orbit Distortion (COD), including bending magnet sorting and survey and alignment of the magnets, are discussed based on the studies of affections to the COD by the bending magnet field error and the misalignment of quadrupoles. The closed orbit correction and the Slow Orbit Feed Back (SOFB) system for the SSRF storage ring are presented in this paper. With these available methods, better results were obtained during the commissioning period with 3 GeV beam energy.     

Study of closed orbit response to magnet vibrations at the SSRF storage ring

This paper presents the analytical and simulation responses of the closed orbit distortion in the SSRF storage ring to random and plane wave like magnet vibrations respectively. It is shown that the use of girder is very beneficial in the view of suppressing this response function. Effect of the independently supported gradient bending magnets to the closed orbit response is given. An analytic formula is written to give a rough estimate of the closed orbit distortion due to ground motion, taking into account the closed orbit response function and girder transfer function. As an example, the result of SSRF case is given.     

Study of closed orbit response to magnet vibrations at the SSRF storage ring

This paper presents the analytical and simulation responses of the closed orbit distortion in the SSRF storage ring to random and plane wave like magnet vibrations respectively. It is shown that the use of girder is very beneficial in the view of suppressing this response function. Effect of the independently supported gradient bending magnets to the closed orbit response is given. An analytic formula is written to give a rough estimate of the closed orbit distortion due to ground motion, taking into account the closed orbit response function and girder transfer function. As an example, the result of SSRF case is given.     

CSRm束流累积阶段闭轨校正系统设计

为测量兰州重离子加速器冷却储存环主环(CSRm)束流累积阶段的闭轨畸变并进行闭轨校正,开发了闭轨校正系统,该系统由轨道测量系统、闭轨控制系统和校正磁铁系统构成。轨道测量系统实现对束流轨道的实时监测;闭轨控制系统读取束流轨道信息,然后进行闭轨校正计算,并将计算后的校正值传输给校正磁铁系统;校正磁铁系统通过改变校正电源的值,改变校正磁铁的强度,实现对束流轨道的调整,完成闭轨校正。模拟测试结果表明,束流轨道水平方向的最大畸变由校正前的3.37 mm减小为校正后的0.39 mm,垂直方向的最大畸变由校正前的4.21 mm减小为校正后的0.31 mm。该系统能够实现响应矩阵的自动测量和束流轨道的自动校正,满足设计要求。     

基于LOCO的上海光源储存环线性光学参数校正

为了测量和校正线性光学参数,在上海光源储存环调束过程当中使用了基于响应矩阵的线性光学参数分析(LOCO)的方法。介绍了应用LOCO进行计算和校正的过程,包括：数值模拟得到束流位置探测器的测量精度对拟合结果的影响,调整四极铁电源电流强度来校正工作点和beta函数周期性的恢复。测量结果表明,在四极铁强度调整幅度在1.5%以内的情况下,储存环的束流光学参数成功地恢复到和设计值相当接近的状态,beta函数和色散函数畸变小于1%。通过束流光学参数的校正,使得在今后的工作当中可以轻松地控制储存环的工作模式。     

Beam based alignment of the SSRF storage ring

There are 140 beam position monitors (BPMs) in the Shanghai Synchrotron Radiation Facility (SSRF) storage ring used for measuring the closed orbit. As the BPM pickup electrodes are assembled directly on the vacuum chamber, it is important to calibrate the electrical center offset of the BPM to an adjacent quadrupole magnetic center. A beam based alignment (BBA) method which varies individual quadrupole magnet strength and observes its effects on the orbit is used to measure the BPM offsets in both the horizontal and vertical planes. It is a completely automated technique with various data processing methods. There are several parameters such as the strength change of the correctors and the quadrupoles which should be chosen carefully in real measurement. After several rounds of BBA measurement and closed orbit correction, these offsets are set to an accuracy better than 10 μm. In this paper we present the method of beam based calibration of BPMs, the experimental results of the SSRF storage ring, and the error analysis.     

Beam based alignment of the SSRF storage ring

There are 140 beam position monitors （BPMs） in the Shanghai Synchrotron Radiation Facility （SSRF） storage ring used for measuring the closed orbit. As the BPM pickup electrodes are assembled directly on the vacuum chamber, it is important to calibrate the electrical center offset of the BPM to an adjacent quadrupole magnetic center. A beam based alignment （BBA） method which varies individual quadrupole magnet strength and observes its effects on the orbit is used to measure the BPM offsets in both the horizontal and vertical planes. It is a completely automated technique with various data processing methods. There are several parameters such as the strength change of the correctors and the quadrupoles which should be chosen carefully in real measurement. After several rounds of BBA measurement and closed orbit correction, these offsets are set to an accuracy better than 10 μm. In this paper we present the method of beam based calibration of BPMs, the experimental results of the SSRF storage ring, and the error analysis.     

利用约束线性最小二乘法实现合肥光源束流闭轨全环校正和反馈

由于存在各种非理想因素,束流在储存环中的闭轨会发生畸变。对束流闭轨畸变进行校正的方法较多,目前合肥光源(HLS)采用奇异值分解(SVD)法进行束流闭轨的全环校正和反馈。针对SVD法不足之处,采用约束线性最小二乘法(CLLS)来改进HLS束流闭轨的全环校正和反馈。介绍了束流闭轨畸变校正的理论,着重介绍应用CLLS对HLS储存环束流闭轨畸变进行全环校正和反馈,并给出运行结果。结果显示,利用CLLS后,HLS敏感实验线站的束流轨道稳定性和重复性得到明显改善。     

利用约束线性最小二乘法实现合肥光源束流闭轨全环校正和反馈

由于存在各种非理想因素,束流在储存环中的闭轨会发生畸变。对束流闭轨畸变进行校正的方法较多,目前合肥光源(HLS)采用奇异值分解（SVD）法进行束流闭轨的全环校正和反馈。针对SVD法不足之处,采用约束线性最小二乘法（CLLS）来改进HLS束流闭轨的全环校正和反馈。介绍了束流闭轨畸变校正的理论,着重介绍应用CLLS对HLS储存环束流闭轨畸变进行全环校正和反馈,并给出运行结果。结果显示,利用CLLS后,HLS敏感实验线站的束流轨道稳定性和重复性得到明显改善。     

Orbit response matrix analysis and lattice periodicity restoration of the SSRF storage ring

In this paper, we present numerically and experimentally the linear beam-optics distortion in the SSRF storage ring and the correction of optics by using a number of quadrupole magnets installed in the storage ring. The measured orbit-response matrices were fitted to the model-response matrices to obtain the β and the dispersion functions in the storage ring. By readjusting the currents of quadrupole-magnet power supplies, we were able to successfully restore the optics parameters to values very close to the design ones, with rms deviations around 1%. This periodicity restoration is verified with the β function measurement,     

基于FPGA的储存环束流轨道联锁系统设计

上海光源储存环束流轨道联锁系统是加速器机器联锁保护系统(MPS)的重要组成部分,针对日常供光和机器研究的需求,需要对束流位置测量系统前各Libera电子学输出的联锁信号进行标记,以区分联锁信号的先后顺序和误报的联锁信号,同时触发所有Libera电子学前锁存逐圈（TBT）数据。新的联锁系统将所有联锁信号通过光纤传输汇总至FPGA数据采集板卡进行甄别,并将该系统集成储存环EPICS控制系统中。实验室测试显示该系统能够能够分辨数十ns范围内模拟的联锁信号,同时输出特定的触发信号至对应的Libera电子学,表明该系统达到设计要求。     

Observation of beam instability in the SSRF storage ring

During the SSRF(Shanghai Synchrotron Radiation Facility) storage ring phase-I commissioning, some instabilities have been observed, and the broadband impedance has also been measured. The primary instabilities at present stage are vertical beam blow up and resistive wall instability.     

Orbit response matrix analysis and lattice periodicity restoration of the SSRF storage ring

In this paper, we present numerically and experimentally the linear beam-optics distortion in the SSRF storage ring and the correction of optics by using a number of quadrupole magnets installed in the storage ring. The measured orbit-response matrices were fitted to the model-response matrices to obtain the β and the dispersion functions in the storage ring. By readjusting the currents of quadrupole-magnet power supplies, we were able to successfully restore the optics parameters to values very close to the design ones, with rms deviations around 1%. This periodicity restoration is verified with the β function measurement.     

Observation of beam instability in the SSRF storage ring

During the SSRF(Shanghai Synchrotron Radiation Facility) storage ring phase-I commissioning, some instabilities have been observed, and the broadband impedance has also been measured. The primary instabilities at present stage are vertical beam blow up and resistive wall instability.     

升级的合肥光源闭轨测量系统及其应用

描述了合肥同步辐射光源二期工程中,电子储存环升级的闭轨测量系统及其在设备研制中的应用。介绍了性能稳定可靠的Bergoz束流位置监测电子学信号处理器。升级后的闭轨测量系统中处理电子学电路的束流位置分辨率可达1μm,系统误差小于10μm。整个测试系统的分辨率小于3μm。利用该高精度闭轨测量系统和基于束流准直系统完成了束流准直四极铁磁中心的测量,并和控制系统完成了储存环全环闭轨反馈校正试验。一个完整的束流位置监测系统已投入了在线运行,保障了为用户提供高稳定高品质的光源。     

Design of a higher harmonic cavity for the SSRF storage ring

Higher harmonic cavity used in the third generation synchrotron light source increases the Touschek lifetime. The higher harmonic cavity of Shanghai Synchrotron Radiation Facility (SSRF) is a 1.5GHz passive superconducting cavity. Its higher order modes (HOM) are extracted by a ferrite HOM damper out of the cryostat. Multi-cell cavity is chosen concerning the voltage. The harmonic cavity dynamics, beam dynamics with passive harmonic cavity and the design of single cell cavity are included in this paper.     

基于MATLAB的合肥光源储存环束流轨道校正系统

 闭轨畸变对合肥同步光源的束流质量产生负面影响,因此必须对闭轨畸变进行校正。本文介绍了基于MATLAB的合肥光源储存环束流轨道校正系统的工作原理、开发过程及测试结果。该系统由束流轨道测量系统、校正铁系统和控制系统组成,基于MATLAB开发的束流轨道校正程序运行于操作员界面工作站上。首先对获取的束流轨道数据进行分析和计算,然后通过控制系统改变校正铁电源的电流以改变校正铁磁场强度,从而实现轨道校正。测试结果表明：束流轨道的最大畸变由校正前的4.468 mm下降到校正后的0.299 mm;标准方差（SDEV）由校正前的2.986 mm下降到校正后的0.087 mm。该系统达到了设计目标。     

磁铁安装误差对束流轨道的影响

采用数值方法系统地分析了HLS储存环磁铁安装误差对束流闭轨的影响,发现造成闭轨畸变的主要原因是四极铁在横向位置的安装误差和二极铁在束流方向的旋转,并给出了它们的放大因子;同时对横向发射度的耦合进行了研究,发现造成垂直方向发射度增加的主要原因是闭轨畸变;在综合考虑各种误差的情况下,提出了需要对各种磁铁进行进一步准直的要求。     

基于MATLAB的合肥光源储存环束流轨道校正系统

闭轨畸变对合肥同步光源的束流质量产生负面影响,因此必须对闭轨畸变进行校正。本文介绍了基于MATLAB的合肥光源储存环束流轨道校正系统的工作原理、开发过程及测试结果。该系统由束流轨道测量系统、校正铁系统和控制系统组成,基于MATLAB开发的束流轨道校正程序运行于操作员界面工作站上。首先对获取的束流轨道数据进行分析和计算,然后通过控制系统改变校正铁电源的电流以改变校正铁磁场强度,从而实现轨道校正。测试结果表明：束流轨道的最大畸变由校正前的4.468 mm下降到校正后的0.299 mm;标准方差（SDEV）由校正前的2.986 mm下降到校正后的0.087 mm。该系统达到了设计目标。     

Optimization of magnet sorting in a storage ring using genetic algorithms

In this paper, the genetic algorithms are applied to the optimization problem of magnet sorting in an electron storage ring, according to which the objectives are set so that the closed orbit distortion and beta beating can be minimized and the dynamic aperture maximized. The sorting of dipole, quadrupole and sextupole magnets is optimized while the optimization results show the power of the application of genetic algorithms in magnet sorting.