1-偶氮苯-3-(3-硝基-5-氯-2-吡啶)-三氮烯的合成及其与铜的显色反应

合成了新显色剂1-偶氮苯-3-(3-硝基-5-氯-2-吡啶)-三氮烯(ABNCPDT)。研究了它与铜的显色反应。在pH10.5的Na2B4O7-NaOH缓冲溶液中,Triton X-100表面活性剂存在下,试剂与铜生成4∶1型红色配合物。配合物的最大吸收峰位于540nm,表观摩尔吸光系数为1.48×105L·mol-1·cm-1。Cu2 浓度在0—480μg/L范围内符合比耳定律,用于测定铝合金中微量铜,结果满意。     

新显色试剂1-(4-磺基苯)-3-(2-吡啶)-三氮烯的合成及其与镉(Ⅱ)的显色反应

合成了一种新三氮烯类显色剂1-(4-磺基苯)-3-(2-吡啶)-三氮烯(简称SPPT),并研究了在Triton X-100存在下,于pH为9.18的Na2B4O7-NaOH缓冲溶液中与镉的显色反应.结果表明,试剂与镉生成橙红色配合物.方法用于废水中微量镉的测定,结果令人满意.     

1-偶氮苯-3-(5-氯-2-吡啶)-三氮烯对银的显色反应及研究

合成了1-偶氮苯-3-(5-氯-2-吡啶)-三氮烯(ABCPDT),研究了ABCPDT与银的显色反应。在Na2B4O7-NaOH缓冲溶液(pH9.5)介质中,Triton X-100存在下试剂与Ag生成络合物(1∶1)。络合物在545nm处有最大吸收峰,络合物的表观摩尔吸光系数为1.55×105L·mol-1·cm-1,Ag含量在0—12μg/25mL范围内符合比耳定律。方法已用于回收定影液中银的测定,结果满意。     

1-（4-硝基苯基）-3-（4,6-二甲基-2-嘧啶）-三氮烯的合成及其与锌（Ⅱ）的显色反应

合成了一种新显色剂1-(4-硝基苯基)-3-(4,6-二甲基-2-嘧啶)-三氮烯(简称NPDMPMT),并研究了在非离子型表面活性剂Triton X-100存在下,于pH为11.0的Na2B4O7-NaOH缓冲溶液中与锌(Ⅱ)的显色反应.结果表明.Zn与试剂NPDMPMT形成1:2的橙黄色配合物,在456nm处有一最大正吸收,在530nm处有一最大负吸收,建立以530nm为参比波长,456nm为测量波长的双峰双波长测定法,其表观摩尔吸光系数为3.16×105L·mol-1·cm-1,锌(Ⅱ)浓度在0-8.0μg/25mL范围内符合比耳定律.方法用于人发中微量锌的测定,结果令人满意.     

2-羟基-4-磺酰氨基苯重氮氨基偶氮苯的合成及与锌的显色反应

在 Triton X- 10 0表面活性剂存在下 ,p H=9.5— 11.5的 Na2 B4O7- Na OH缓冲溶液中 ,2 -羟基 - 4-磺酰氨基苯重氮氨基偶氮苯 (HSDAA)与锌 ( )生成 2∶ 1型深红色配合物。最大吸收峰为 λ=5 30 nm处 ,表观摩尔吸光系数为 1.2 4× 10 5L· mol-1· cm-1。 Zn2 的浓度在 0— 4 80μg/L范围内符合比耳定律。用于测定样品中的微量锌 ,结果满意。     

离子缔合物光度法测定微量BrO3-

在 0 .1 6 mol/ L H2 SO4介质中 ,2 - (5 -氯 - 2 -吡啶偶氮 ) - 5 -二乙氨基苯酚 (5 - Cl- PADAP)与 Br O-3 和 SCN-形成紫红色三元离子缔合物 ,最大吸收波长为 5 6 0 nm,表观摩尔吸光系数为 1 .9× 1 0 4L· mol-1 · cm-1 ,Br O-3 含量在 0— 2× 1 0 -5mol/ L范围内符合比耳定律。方法可用于化学试剂中微量 Br O-3 的测定。     

1-(6-羟基-2-嘌呤基)-3-[4-(苯基偶氮)苯基]- 三氮烯分光光度法测定微量镍

在pH=10.97的NaB4O7-NaOH缓冲溶液中,表面活性剂Tween-80存在下,1-(6-羟基-2-嘌呤基)-3-[4-(苯基偶氮)苯基]-三氮烯(HPAPT)与镍的显色反应,形成一种稳定的1∶2红色配合物,其最大吸收波长位于540nm,表观摩尔吸光系数ε540＝2.06×105L·mol-1·cm-1,Ni(Ⅱ)在0-15μg/25mL范围内符合比耳定律.结合萃取分离,应用于人发、大米和油菜中镍的测定,结果令人满意.     

1-(6-硝基-2-苯并噻唑)-3-(4-硝基苯)-三氮烯与铜显色反应的研究及应用

在TritonX-100表面活性剂存在下,pH为10.0-11.0的Na2B4O7-NaOH缓冲溶液中,1-(6-硝基-2-苯并噻唑)-3-(4-硝基苯)-三氮烯(NBTNPT)与铜生成2:1配合物。配合物的最大负吸收峰是540nm,表观摩尔吸光系数为1.15×105L·mol-1·cm-1。Cu2 的质量浓度在0-360μg/L符合比耳定律。测定铝合金样品中的微量铜,结果满意。     

新显色剂3,5-二(1-羧基-4,5-二甲氧基-2-苯氨基偶氮基)苯甲酸与铜(Ⅱ)的显色反应

研究了新显色剂3,5-二(1-羧基-4,5-二甲氧基-2-苯氨基偶氮基)苯甲酸(CDMOBAABA)与铜(Ⅱ)的显色反应。在TritonX-100存在下,于pH9.5的NH3-NH4Cl缓冲介质中,CDMOBAABA与铜(Ⅱ)形成棕红色配合物。试剂与络合物的最大吸收波长分别为450nm和540nm。表观摩尔吸光系数为2.43×105L·mol-1.cm-1。铜(Ⅱ)含量在0—20μg/25mL范围内符合比耳定律。该方法用于铝合金样品中铜的测定,结果与原子吸收光谱法相吻合,相对标准偏差1.89%。     

5-(4-氯苯基偶氮)-8-苯磺酰氨基喹啉与钴(Ⅱ)的显色反应及其应用

本文用光度法研究了新显色剂5-(4-氯苯基偶氮)-8-苯磺酰氨基喹啉(CPBSQ)与钴的显色反应和最佳条件.结果表明,在pH 9.5-11.5范围内及有氯化十六烷基吡啶(CPC)和硫脲-酒石酸钾钠存在下,Co(Ⅱ)与CPBSQ形成1∶3的稳定配合物,其最大吸收波长为590nm.依此建立了一种测定Co(Ⅱ)的新光度法.Co(Ⅱ)的浓度在0-15.0μg/25mL范围内符合比耳定律,其摩尔吸光系数为1.15×105L*mol-1*cm-1.常见离子对Co2+的测定均无严重干扰.本法具有灵敏度高、选择性好的特点.用于VB12针剂中钴含量的测定,相对标准偏差为0.5%-0.6%,标准加入回收率为98%-104%.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.