亚甲基蓝分光光度法测定锑浸出液中硫化钠

湿法炼锑中常采用硫化钠作为从锑矿中提取锑硫化物的浸出剂。准确测定锑浸出液中的硫化钠浓度对掌握和完善湿法炼锑工艺、提高生产效率有重要作用。将亚甲基蓝分光光度法用于锑浸出液中硫化钠的测定,考察了波长选择、体系酸度、显色时间、基质干扰等条件,测评、优化了方法;将方法应用于锑浸出液中硫化钠的测定,方法检出限为0.002mg/L,测定结果相对标准偏差≤3%,加标回收率≥90%。方法能较理想地应用于锑浸出液中硫化钠的测定,丰富了锑浸出液中硫化钠的测定方法,也为相关研究提供了支持与参考。     

On the definition of the excess permittivity of a fluid mixture

It is shown that under the assumption of no intermolecular interaction, the permittivity of a homogeneous linear and isotropic fluid mixture is the sum of the individual permittivities weighted with the mole fractions of the components. For definiteness, a proof is given for gasses under standard temperature and pressure; it is, however, easy to generalize it to other conditions, as well as to liquids, as long as the assumption of no intermolecular interaction is retained. Also, although the proof is given for a binary mixture, it is a simple exercise to extend it to any multicomponent mixture.     

亚甲基蓝分光光度法测定锑浸出液中硫化钠

湿法炼锑中常采用硫化钠作为从锑矿中提取锑硫化物的浸出剂。准确测定锑浸出液中的硫化钠浓度对掌握和完善湿法炼锑工艺、提高生产效率有重要作用。将亚甲基蓝分光光度法用于锑浸出液中硫化钠的测定,考察了波长选择、体系酸度、显色时间、基质干扰等条件,测评、优化了方法;将方法应用于锑浸出液中硫化钠的测定,方法检出限为0.002mg/L,测定结果相对标准偏差≤3%,加标回收率≥90%。方法能较理想地应用于锑浸出液中硫化钠的测定,丰富了锑浸出液中硫化钠的测定方法,也为相关研究提供了支持与参考。     

Sol-Gel Fabrication of Rare-Earth Doped Photonic Components

The use of sol-gel to fabricate silica-on-silicon waveguides, and particularly erbium-doped waveguide amplifiers, is reviewed. In particular, efforts to use sol-gel to improve molecular homogeneity in heavily Er-doped silica-based films is discussed. A variety of material studies carried out to investigate the gain limitations found in these materials is then presented. These include x-ray diffraction, ellipsometry and Rutherford backscattering. Excess heat treatment is used to force crystallisation of the films, and analysis of the resulting structure is used to infer properties of the glass before the additional heating. The use of erbium alkoxide precursors is shown to alter the erbium environment in the final glass, in comparison to the use of inorganic erbium salts.     

QUASI: a novel method for simultaneous superposition of multiple flexible ligands and virtual screening using partial similarity

The structure of many receptors is unknown, and only information about diverse ligands binding to them is available. A new method is presented for the superposition of such ligands, derivation of putative receptor site models and utilization of the models for screening of compound databases. In order to generate a receptor model, the similarity of all ligands is optimized simultaneously taking into account conformational flexibility and also the possibility that the ligands can bind to different regions of the site and only partially overlap. Ligand similarity is defined with respect to a receptor site model serving as a common reference frame. The receptor model is dynamic and coevolves with the ligand alignment until an optimal self-consistent superposition is achieved. When ligand conformational flexibility is permitted, different superposition models are possible and consistent with the data. Clustering of the superposition solutions is used to obtain diverse models. When the models are used to screen a database of compounds, high enrichments are obtained, comparable to those obtained in docking studies.     

How to cancel the program of body aging?

This issue is devoted to biochemical aspects of studies on aging of living organisms. During last several years, new evidence was published to show that aging is programmed by the genome. If this is really the case, there is a chance to prevent aging just as the programmed cell death (apoptosis) can be prevented by inhibitors arresting some steps of this process. That is why the main problem discussed by the majority of the authors contributing to this issue consists in an attempt to answer the question whether aging is programmed or not. At present it is hardly possible to solve this problem. However, we already can assume that at least there are no facts allowing to exclude existence of the aging program in humans. Thus, there is a perspective to invent a chemical agent competent in transferring humans from aging to non-aging creatures, which is exemplified by the naked mole rat whose death rate is independent of age.     

Polymers for Enhanced Oil Recovery Technology

Recently enhance oil recovery (EOR) technology is getting more attention by many countries since energy crises are getting worse and frightened. One of the reasons for this is due to the shortage of current oil resources and difficulties in finding a new oil field. Indonesia is one of the examples, before 2004 Indonesia is a net oil exporting country but after that Indonesia is a net oil importing country. The oil demand in the country is increasing while the oil production capacity is decreasing. In fact, when a new oil reservoir is drilled, the oil amount obtained from it is about 20-40% of the potential and hence there is still 60-80% oil left in the reservoir. Application of EOR technology gives an additional chance to get out more oil from the reservoir, possibly about another 20%. Polymer is the material that plays an important role in the application of EOR technology, especially surfactant and hydrogel polymers. In the technology, surfactant polymer is injected to the reservoir to reduce an interfacial tension between oil and water and is able to wipe out the trapped oil from the reservoir rock and hence increase the oil production. While an injection of hydrogel polymer to the reservoir is to increase a viscosity of fluid containing water so that the fluid is more difficult to flow than the oil, and as a result, the oil production increases. The most common polymer used for this application is polyacrylamide group.     

Experimental study of dielectrophoresis and liquid dielectrophoresis mechanisms for particle capture in a droplet

This work presents a microfluidic system that can transport, concentrate, and capture particles in a controllable droplet. Dielectrophoresis (DEP), a phenomenon in which a force is exerted on a dielectric particle when it is subjected to a non-uniform electric field, is used to manipulate particles. Liquid dielectrophoresis (LDEP), a phenomenon in which a liquid moves toward regions of high electric field strength under a non-uniform electric field, is used to manipulate the fluid. In this study, a mechanism of droplet creation presented in a previous work that uses DEP and LDEP is improved. A driving electrode with a DEP gap is used to prevent beads from getting stuck at the interface between air and liquid, which is actuated with an AC signal of 200 V(pp) at a frequency of 100 kHz. DEP theory is used to calculate the DEP force in the liquid, and LDEP theory is used to analyze the influence of the DEP gap. The increment of the actuation voltage due to the electrode with a DEP gap is calculated. A set of microwell electrodes is used to capture a bead using DEP force, which is actuated with an AC signal of 20 V(pp) at a frequency of 5 MHz. A simulation is carried out to investigate the dimensions of the DEP gap and microwell electrodes. Experiments are performed to demonstrate the creation of a 100-nL droplet and the capture of individual 10-μm polystyrene latex beads in the droplet.     

Facile Electrochemical Hydrogenation and Chlorination of Glassy Carbon to Produce Highly Reactive and Uniform Surfaces for Stable Anchoring of Thiolated Molecules

Carbon is a highly adaptable family of materials and is one of the most chemically stable materials known, providing a remarkable platform for the development of tunable molecular interfaces. Herein, we report a two‐step process for the electrochemical hydrogenation of glassy carbon followed by either chemical or electrochemical chlorination to provide a highly reactive surface for further functionalization. The carbon surface at each stage of the process is characterized by AFM, SEM, Raman, attenuated total reflectance (ATR) FTIR, X‐ray photoelectron spectroscopy (XPS), and electroanalytical techniques. Electrochemical chlorination of hydrogen‐terminated surfaces is achieved in just 5 min at room temperature with hydrochloric acid, and chemical chlorination is performed with phosphorus pentachloride at 50 °C over a three‐hour period. A more controlled and uniform surface is obtained using the electrochemical approach, as chemical chlorination is observed to damage the glassy carbon surface. A ferrocene‐labeled alkylthiol is used as a model system to demonstrate the genericity and potential application of the highly reactive chlorinated surface formed, and the methodology is optimized. This process is then applied to thiolated DNA, and the functionality of the immobilized DNA probe is demonstrated. XPS reveals the covalent bond formed to be a C?S bond. The thermal stability of the thiolated molecules anchored on the glassy carbon is evaluated, and is found to be far superior to that on gold surfaces. This is the first report on the electrochemical hydrogenation and electrochemical chlorination of a glassy carbon surface, and this facile process can be applied to the highly stable functionalization of carbon surfaces with a plethora of diverse molecules, finding widespread applications.     

A universal equation for the emission range of x rays from bulk specimens.

The derivation of a universal equation to compute the range of emitted X rays is presented for homogeneous bulk materials. This equation is based on two fundamental assumptions: the varphi(rhoz) curve of X-ray generation is constant and the ratio of the emitted to the generated X-ray range is equal to the ratio of the emitted to the generated X-ray intensity. An excellent agreement is observed with data obtained from Monte Carlo simulations of 200,000 electron trajectories in C, Al, Cu, Ag, Au, and an Fe-B alloy with boron weight fractions equal to 0.01, 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8, 0.9, and 0.99, performed with the electron beam energy varied from 1 to 30 keV in 1-keV steps. When the ratio of the generated X-ray range to the photon mean free path is much smaller than one, the emission X-ray range is equal to the generated X-ray range, but when this ratio is much greater than one, the emission X-ray range is constant and is given by the product of the effective photon mean free path multiplied by the sine of the take-off angle.     

Thermomechanical degradation of filled polypropylene

The main problem in post-consumer plastics recycling is due to the thermomechanical stress acting on the melt during the reprocessing operations. The macromolecules break because of the temperature and of the mechanical stress. The extent of degradation is then correlated to the level of mechanical stress which, in turn, is proportional to the viscosity of the melt. The presence of fillers increases the viscosity of the polymers and then it is expected that the level of thermomechanical degradation of these systems is larger than that of the unfilled material. In this work the thermomechanical degradation kinetic of a polypropylene sample is investigated as a function of the calcium carbonate content. It is shown that the decrease of viscosity, that is the decrease of molecular weight, is directly related to the increase of viscosity due to the filler content. The worsening of the mechanical properties are consistent with the change of viscosity.     

Protocol for uncertainty assessment of half-lives

The apparent tendency to underestimate the uncertainty of experimentally determined half-life values of radionuclides is discussed. It is argued that the uncertainty derived from a least-squares analysis of a decay curve is prone to error. As it is quite common for a series of activity measurement results to be autocorrelated, the prerequisite of randomness of data for common statistical tests to apply is not fulfilled. In this work, an alternative data analysis method is applied that leads to a more realistic uncertainty budget. The uncertainty components are being subdivided in three categories according to the relative frequency at which they occur, an appropriate uncertainty propagation formula applied and then the total uncertainty obtained from an independent sum. An attempt is made to apply the protocol to problematic cases in literature, yet it is clear that the reporting is usually incomplete for a full uncertainty analysis. Suggestions are made for a concise but more complete reporting style, for the sake of traceability.     

Structure of organoclays--an X-ray diffraction and thermogravimetric analysis study

X-ray diffraction has been used to study the changes in the surface properties of a montmorillonitic clay through the changes in the basal spacings of montmorillonite (SWy-2) and surfactant-intercalated organoclays. Variation in the d-spacing was found to be a step function of the surfactant concentration. High-resolution thermogravimetric analysis (HRTG) shows that the thermal decomposition of SWy-2-MMTs modified with the surfactant octadecyltrimethylammonium bromide takes place in four steps. A mass-loss step is observed at room temperature and is attributed to dehydration of adsorption water. A second mass-loss step is observed over the temperature range 87.9 to 135.5 degrees C and is also attributed to dehydration of water hydrating metal cations such as Na+. The third mass loss occurs from 178.9 to 384.5 degrees C and is assigned to a loss of surfactant. The fourth mass-loss step is ascribed to the loss of OH units through dehydroxylation over the temperature range 556.0 to 636.4 degrees C. A model is proposed in which, up to 0.4 CEC, a surfactant monolayer is formed between the montmorillonitic clay layers; up to 0.8 CEC, a lateral-bilayer arrangement is formed; and above 1.5 CEC, a pseudotrimolecular layer is formed, with excess surfactant adsorbed on the clay surface.     

Theoretical study of the ruthenium-catalyzed cyclocotrimerization of alkynes with isocyanates and iothiocyanates: cemoselective formation of pyridine-2-one and thiopyrane-2-imine

The cyclocotrimerization of acetylene with isocyanate HNCO and isothiocyanate HNCS, mediated by CpRuCl, is theoretically investigated on the basis of DFT/B3LYP calculations. By these means, the experimental result can be rationalized as to why, with HNCO, a nitrogen-heterocycle is formed, but with HNCS a sulfur-heterocycle is formed. According to the proposed mechanism, the key reaction step is the addition of a double bond to a metallacyclopentatriene formed by oxidative coupling of two acetylene ligands coordinated to CpRuCl, giving a bicyclic carbene intermediate. This double-bond-addition is initiated by eta1 attack at the ruthenium center, and it is just the attacking atom that is going to be incorporated into the cycle. Thus, the chemoselectivity originates from the fact that, for HNCO, N attack is preferred over O, but for HNCS, S attack is preferred over N. The onward reaction is a reductive elimination to give a coordinatively unsaturated metallaheteronorbornene intermediate finally rearranging to a ligated heterocycle. Completion of the cycles is achieved by an exothermic displacement of the respective heterocyclic product by two acetylene molecules which regenerates the bisacetylene complex.     

Measurement uncertainty of liquid chromatographic analyses visualized by Ishikawa diagrams

Ishikawa, or cause-and-effect diagrams, help to visualize the parameters that influence a chromatographic analysis. Therefore, they facilitate the set up of the uncertainty budget of the analysis, which can then be expressed in mathematical form. If the uncertainty is calculated as the Gaussian sum of all uncertainty parameters, it is necessary to quantitate them all, a task that is usually not practical. The other possible approach is to use the intermediate precision as a base for the uncertainty calculation. In this case, it is at least necessary to consider the uncertainty of the purity of the reference material in addition to the precision data. The Ishikawa diagram is then very simple, and so is the uncertainty calculation. This advantage is given by the loss of information about the parameters that influence the measurement uncertainty.     

On the evaluation of the non-interacting kinetic energy in density functional theory

The utility of both an orbital-free and a single-orbital expression for computing the non-interacting kinetic energy in density functional theory is investigated for simple atomic systems. The accuracy of both expressions is governed by the extent to which the Kohn-Sham equation is solved for the given exchange-correlation functional and so special attention is paid to the influence of finite Gaussian basis sets. The orbital-free expression is a statement of the virial theorem and its accuracy is quantified. The accuracy of the single-orbital expression is sensitive to the choice of Kohn-Sham orbital. The use of particularly compact orbitals is problematic because the failure to solve the Kohn-Sham equation exactly in regions where the orbital has decayed to near-zero leads to unphysical behaviour in regions that contribute to the kinetic energy, rendering it inaccurate. This problem is particularly severe for core orbitals, which would otherwise appear attractive due to their formally nodeless nature. The most accurate results from the single-orbital expression are obtained using the relatively diffuse, highest occupied orbitals, although special care is required at orbital nodes.     

Adsorption and structure of hydrocarbons in MCM-41: a computational study

The adsorption of linear, branched, and cyclic hydrocarbons in MCM-41 is studied using Configurational Bias Monte Carlo simulations. A new computational model for MCM-41 is proposed which, although simple, is able to predict adsorption isotherms which are in agreement with the scarce experimental data. The structure of the adsorbed phase is analyzed and found to be similar to that of studies using small, hard spheres trapped in pores. The adsorption of mixtures is investigated, and the adsorption hierarchy is discussed. The structure of the adsorbed mixture is revealed and shows that all components of the mixture exhibit structure, even if they are only adsorbed in small quantities. Finally, the model is modified to include surface roughness and the effect on the adsorption isotherms and structure of the adsorbed phase is discussed.     

Appropriate volumes for adsorption isotherm studies: the absolute void volume, accessible pore volume and enclosing particle volume

In adsorption studies the choice of an appropriate void volume in the calculation of the adsorption isotherm is very crucial. It is often taken to be the apparent volume as determined by the helium expansion experiments. Unfortunately this method has difficulties especially when dealing with microporous solids, in which adsorption of helium might become significant at ambient temperatures. The amount adsorbed is traditionally obtained as the excess amount and the term "excess" refers to the excess over the amount occupying the apparent volume that has the same density as the bulk gas density. This could give rise to the maximum in the plot of excess amount versus pressure under supercritical conditions, and in some cases giving negative excess. Such behavior is difficult to analyze because the excess amount is not amenable to any classical thermodynamic treatments. In this paper we will present a method to determine the absolute void volume, and in that sense this volume is independent of temperature and adsorbate. The volume that is accessible to the centers of gas molecules is also investigated, and it is called the accessible volume. This volume depends on the choice of adsorbate, and it is appropriate to use this volume to calculate the pore density because we can assess how dense the adsorbed phase is. In the quest to determine the "absolute" adsorption isotherm so that a thermodynamics analysis can be applied, it is necessary to introduce the concept of "enclosing" volume, which is essentially the volume that encloses all solid particles, including all void spaces in them. The amount adsorbed is defined by the number of molecules residing in this volume. Having these volumes, we can derive the geometrical accessible void volume inside the particle and the solid volume, from which the particle and solid densities can be calculated.     

Heat transfer through fibrous assemblies by fractal method

Fractal theory has been proved effective to characterize the complex pore structure. In this article, the fractal method is utilized to study the structure property of fibrous assemblies. The box dimension parameter is applied to characterize the pore structure of fibrous assemblies by analyzing the electronic scanning microscope images of the fibrous assemblies. Furthermore, a fractal model for predicting effective heat conductivity is established. Experiment is conducted to verify the model, and good agreement is found between the experimental and theoretical results. The fractal model is also compared with the previous models for predicating heat conductivity, and the former is proved to be more accurate.